纳米磁性壳聚糖微球固定化酵母醇脱氢酶的研究

建立了以纳米级磁性壳聚糖微球(magnetic chitosan microspheres , M-CS)为载体固定化酵母醇脱氢酶(yeast alcohol dehydrogenase,YADH)的方法,优化了YADH的固定化条件,考察了固定化酶的性质。结果表明,M-CS 呈规则的圆球形,粒径在30nm 左右,具有较好的磁响应性。酵母醇脱氢酶固定化适宜条件为:50 mg 磁性壳聚糖微球,加入20mL 0.25 mg/mL 酵母醇脱氢酶(蛋白质含量)磷酸盐缓冲液(0.05 mol/L ,pH 7.0) ,在4 ℃固定2h。M-CS 容易吸附酵母醇脱氢酶,但吸附的酶量受载体与酶的比例、溶液的离子浓度、溶液pH的影响明显,而温度对吸附的酶量的影响则相对较弱。相对于游离的酵母醇脱氢酶,固定化酶的最适温度略有升高,可明显改善其热稳定性、酸碱稳定性、操作稳定性和贮存稳定性。     

壳聚糖固定化琼脂酶的研究

采用壳聚糖微球对琼脂酶进行固定化,在单因素实验的基础上用正交试验法确定最佳固定化工艺。结果表明:在戊二醛体积分数为2.5%,交联时间为6 h,加酶量为15 mL,固定时间为3 h时固定酶的活力最高;固定化酶的最适反应温度及最适pH分别为50℃和8.5,高于游离酶;同时其热稳定性及操作稳定性均高于游离酶。     

蒜氨酸酶的固定化及其酶学性质研究

为了提高蒜氨酸酶的稳定性并实现酶的反复利用,研究了影响蒜氨酸酶固定化的因素及固定化蒜氨酸酶的酶学性质。蒜氨酸酶的固定化以壳聚糖微球为载体,戊二醛为交联剂,固定化的最适条件为：戊二醛浓度4%,给酶量20.2U,交联时间2h。固定化蒜氨酸酶的最适pH值7.0,最适温度35℃,米氏常数Km 7.9 mmol/L,操作稳定性比较好,连续使用10次后酶活力损失低于10%。     

桦褶孔菌漆酶固定化及其对染料的降解

采用壳聚糖交联法和海藻酸钠-壳聚糖包埋交联法固定化桦褶孔菌产生的漆酶,探讨最佳固定化条件,固定化漆酶的温度,pH稳定性及操作稳定性,并以两种固定化酶分别对4种染料进行了降解.结果表明:(1)壳聚糖交联法固定化漆酶的最佳条件为:壳聚糖2.5%,戊二醛7%,交联时间2h,固定化时间5h,给酶量1g壳聚糖小球:1mL酶液(1U/mL),固定化效率56%;(2)海藻酸钠-壳聚糖包埋交联法固定化漆酶的最佳条件为:海藻酸钠浓度4%,壳聚糖浓度0.7%,氯化钙浓度5%,戊二醛浓度0.6%,给酶量4mL 4%海藻酸钠:1mL酶液(1U/mL),固定化效率高达86%;(3)固定化的漆酶相比游离漆酶有更好的温度和pH稳定性;(4)比较两种固定化漆酶,海藻酸钠-壳聚糖包埋交联法固定化酶的温度及酸度稳定性要优于壳聚糖固定化酶,但可重复操作性要弱于后者,两者重复使用8次后的剩余酶活比率分别为71%及64%;(5)两种固定化酶对所选的4种不同结构的合成染料均有较好的降解效果,其中壳聚糖固定化酶对茜素红的降解效果及重复使用性极佳,重复降解40mg/L的茜素红10次,降解率仍保持在100%.     

壳聚糖纳米磁性微球固定脂肪氧合酶的研究

实验采用溶胶凝胶法制备了纳米磁性Fe3O4,并用壳聚糖对颗粒2四川大学,生命科学学院,四川成都表面进行了表面修饰得到壳聚糖纳米磁性微球复合载体,再以戊二醛为交联剂将脂肪氧合酶固定在复合载体上,并测定了不同因素对游离酶和固定化酶活性的影响;实验表明,微粒在电镜观察下呈亮黑色球状,直径约为150nm,并具有良好的磁性,固定在载体上酶的含量约为7.6%,游离酶的最适温度为30℃,最适p H8.0,而固定化酶的最适温度为30℃,最适p H9.0,当H2O2浓度为12.0 g/L时,游离酶和固定化酶的活性最强;实验结果表明通过交联的方法成功将脂肪氧合酶固定在了纳米磁性四氧化三铁颗粒上,并表现出了较好的活性。     

活性炭吸附固定化粪产碱杆菌青霉素G酰化酶

目的：以活性炭为载体固定化粪产碱杆菌来源的青霉素G酰化酶,考察固定化酶的性质。方法：对影响酶固定化的因素优化筛选,确定有显著影响的因素：pH、离子强度、酶量、固定化时间进行L934的正交实验,获得最佳固定化条件,并对固定化酶的最适反应温度、pH及批次稳定性进行研究。结果：最佳固定化条件为：载体0.3g,酶量5mL,总反应体系为12mL,离子强度1mol/L,温度4℃,pH 7.0,固定化40h;最高固定化酶活性为135.9U/g湿载体。固定化酶性最适反应温度为55℃,最适pH为10,重复使用12次后没有活性损失。结论：活性炭吸附固定化青霉素G酰化酶的活性高,批次反应稳定,具有工业应用潜力。     

壳聚糖固定化德氏根霉脂肪酶的研究

研究了壳聚糖吸附和戊二醛交联对脂肪酶固定化条件,在室温条件下将0．4g酶粉溶于pH6．0缓冲液中,加入10g壳聚糖,摇匀,再加入浓度为0．6％戊二醛交联6h,得到固定化酶,酶活力回收率约为54．2％。固定化酶的半失活温度比游离酶的高,半失活温度由游离酶的47℃提高到100℃,最适反应温度由40℃上升至80℃,最适pH由6下降到5．5,固定化酶K’m值由游离酶的Km 50mg／mL增加到56mg／mL。该固定化脂肪酶用于酯的合成;在80℃条件下经过10批次连续水解植物油反应,固定化酶的活力仍保持在82．6％以上。     

以伴刀豆球蛋白为介质定向固定化脲酶的研究

将戊二醛将伴刀豆球蛋白(ConA)和壳聚糖载体交联,然后利用ConA与脲酶糖链的特异性结合作用,实现脲酶的定向固定化.定向固定化的最适条件为戊二醛浓度3.5%、ConA浓度1mg/mL、ConA溶液pH值7.0、脲酶浓度0.4mg/mL.定向固定化脲酶的最适pH 5.0～6.0、最适温度77℃,米氏常数Km11.76mmol/L,与游离酶及非定向固定化脲酶比较,定向固定化脲酶的最适pH向酸性范围发生了偏移并有更宽的pH适用范围,最适温度提高,与底物的亲和力较大,且有较好的操作稳定性.     

金属框架结构材料MOF-199对漆酶的固定化及其性质

以金属框架结构材料MOF-199为载体对漆酶进行固定化,并对固定化酶的性质进行初步研究。首先,以3-氨基丙基三乙氧基硅烷对载体MOF-199进行表面氨基化修饰,再用戊二醛对载体进行活化,最后对漆酶进行固定化。固定化条件优化结果表明:在漆酶质量浓度0.3 g/L,戊二醛用量1%(体积分数),pH 4.8下固定7 h,制得固定化酶活性最高。对固定化酶的研究发现:最适反应温度为40℃,最适pH为5.2,在连续操作7次后,固定化酶的活力仍能保持在51%。固定化漆酶热稳定性,pH耐受性,贮存稳定性均明显高于游离漆酶。     

仿生法制备氧化硅载体固定化苏氨酸脱氨酶及其酶学性质

通过共沉淀法制备无机氧化硅载体,然后将其应用到苏氨酸脱氨酶的固定化研究中。用扫描电子显微镜对氧化硅载体进行表征,优化了固定化条件,当n(Si):n(N)为1∶1、偏硅酸浓度为0.03 mol/L、酶添加量为0.16mg/m L时,固定化的效率最高。接着对固定化酶和游离酶的酶学性质进行了考察,结果发现:固定化酶和游离酶的最适pH都是9.0,最适温度都是45℃,而相对于游离酶,固定化酶在pH 9.0~10.0和温度35~50℃范围内稳定性更好。固定化酶的米氏常数为7.48 mmol/L,重复使用15次后,酶活力保持80%以上。说明仿生氧化硅制备的固定化苏氨酸脱氨酶具有酶活回收率高、力学强度高和操作稳定性好等优势。     

Application and characterization of magnetic chitosan microspheres for enhanced immobilization of cellulase

In this study, a unique carrier magnetic chitosan microspheres (MCTS) was simply synthesized by anchoring Fe₃O₄ onto chitosan for direct immobilization of cellulases cross-linked by gluteraldehye. The structure and morphology were characterized using FT-IR, TGA, VSM and SEM. The optimum immobilization conditions were investigated: immobilized pH 7.0, amount of enzyme 15?mL (0.1?mg/mL), immobilization temperature 30?°C, immobilization time 5?h. At optimum conditions, MCTS achieved maximum enzyme solid loading rate of 73.5?mg/g, while recovery of enzyme activity approached to 71.6%. In the recycle test, immobilized cellulases operated without significant loss in its initial performances after 3 cycles, which indicated that immobilized cellulases can be regenerated and reused. The immobilized enzyme has better values of thermal and storage stability than that of free enzyme. Therefore, MCTS may be considered as a candidate with potential value of application in large-scale operations for cellulases immobilization.     

壳聚糖固定化木瓜蛋白酶的研究

以自制的壳聚糖作为载体,用戊二醛作交联剂,优化了固定化条件,研制成壳聚糖固定化木瓜蛋白酶。其活性回收率达到42—53％,操作半衰期达到一个月以上,对热、乙醇以及尿素的稳定性有很大的提高,Km值为0.67×10~2mg/mL,最适温度65—70℃,最适pH8.0,能使啤酒中的蛋白质浓度从56.5mg/L减少到2.7mg/L,可以消除啤酒的低温混浊现象。     

以聚丙烯腈纤维为载体制备固定化青霉素G酰化酶的研究

以酸部分水解聚丙烯腈纤维为载体 ,以戊二醛为交联剂 ,共价键结合制备了固定化胞外青霉素G酰化酶。当水解后的载体中 NH2 基含量为 690 μmol g和含水量为 64%时 ,对酶蛋白的固定量达 1 0 0mg g以上 ,固定化酶的活力达 2 30 0IU g ,酶活力总产率为 30 % ,固定化效率为 56%。酶活力的总产率和固定化率随加酶量的增加而降低。该酶可以将浓度为 2 5%～1 2 5%的青霉素G钾盐水解 98%以上。批投青霉素G钾盐为 1 0g,酶负荷为 1 50IU g(PGK) ,经2 0批水解反应后 ,剩余酶活力为 80 %。用二硫基苏醣醇处理固定化酶 ,对水解青霉素G钾盐的操作稳定性有促进作用。固定化酶的室温保存半衰期为 1 30d。用戊二醛和硼氢化钠溶液处理固定化酶后 ,酶活力的室温保存稳定性有所降低。     

Characterization and immobilization of the laccase from Pleurotus ostreatus and its use for the continuous elimination of phenolic pollutants

A laccase, the only ligninolytic enzyme produced by the basidiomycete Pleurotus ostreatus strain RK 36 was purified to homogeneity and characterized. The enzyme is a monomeric protein with a molecular weight of 67 000 Da and an isoelectric point of 3.6. Type I and type III Cu(2+) centers were identified by spectrophotometry. With syringaldazine as substrate laccase showed the highest oxidation rates at pH 5.8, 50 degrees C, and in 40 mM phosphate buffer. Among the tested stabilization parameters laccase retained most of its activity in high ionic buffer, pH 10, -20 degrees C, in the presence of 10 mM benzoic acid and with 35% ethylene glycol respectively. Crude laccase was covalently immobilized to Eupergit((R))C. Benzoate was found to stabilize the enzyme during the immobilization process. The activity loss of laccase during 10 days at 25 degrees C storage was 2% on average. Continuous elimination of 2,6-dimethoxyphenol by immobilized laccase was carried out in a packed bed reactor followed by filtration of the formed precipitate. The solubility of the polymerisates of oxidized syringaldazine, o-dianisidine, and 2,6-dimethoxyphenol with respect to temperature, pH-value and organic solvents were examined. The precipitates were found to be insoluble under non-extreme environmental conditions.     

以伴刀豆球蛋白为介质定向固定化脲酶的研究

将戊二醛将伴刀豆球蛋白(ConA)和壳聚糖载体交联, 然后利用ConA与脲酶糖链的特异性结合作用, 实现脲酶的定向固定化。定向固定化的最适条件为戊二醛浓度3.5%、ConA浓度1 mg/mL、ConA溶液pH值7.0、脲酶浓度 0.4 mg/mL。定向固定化脲酶的最适pH 5.0~6.0、最适温度77°C、米氏常数Km11.76 mmol/L, 与游离酶及非定向固定化脲酶比较, 定向固定化脲酶的最适pH向酸性范围发生了偏移并有更宽的pH适用范围, 最适温度提高, 与底物的亲和力较大, 且有较好的操作稳定性。     

Preparation and characterization of epoxy-functionalized magnetic chitosan beads: laccase immobilized for degradation of reactive dyes

Cross-linked magnetic chitosan beads were prepared by phase-inversion technique in the presence of epichlorohydrin under alkaline condition, and used for covalent immobilization of laccase. The activity of the immobilized laccase on the magnetic chitosan was about 260 U (g/dry beads) with an enzyme loading of about 16.33 ± 0.39 mg [(g/dry beads) mg/g]. Kinetic parameters, V _max and K _m values were determined as 21.7 U/mg protein and 9.4 μM for free enzyme, and 15.6 U/mg protein and 19.7 μM for the immobilized laccase, respectively. The operational and thermal stabilities of the immobilized laccase were improved compared to free counterpart. The immobilized laccase was operated in a batch reactor for the decolorization of reactive dyes from aqueous solution. The laccase immobilized on magnetic chitosan beads was very effective for removal of textile dyes from aqueous solution which creates an important environmental problem in the discharged textile dying solutions.