维生素B2在玻碳电极上的伏安行为及痕量检测

玻碳电极在活化后,在pH=5．6的柠檬酸-磷酸二氢钠缓冲体系中,在-0．8—0．1V范围内进行循环伏安扫描,可观察到明显的准可逆氧化还原峰,峰电流与扫速成正比。实验表明,VB2在玻碳电极表面有弱吸附现象,VB2浓度与峰电流在1．0×10^-5～2．0×10^-4moL／L之间线性关系较好,最低检测隈为5．0×10^-7mol／L。     

应用DPV法测定油脂中抗氧化剂PG、BHT含量的研究

目的：PG、BHT是食用油常用的抗氧化剂，本研究基于PG、BHT的电化学性质，探讨建立一种新型的油脂中抗氧化剂添加量快速测定方法。方法：以Nafion修饰玻碳电极作为工作电极，以LiClO4乙腈溶液作为电解质，采用微分脉冲溶出伏安扫描测定法（DPV）测定其含量与峰电流的关系。结果：PG在3.3×10-5～1.65×10-4 mol/L、BHT在1.32×10-4～3.3×10-4 mol/L内加入量与氧化峰电流呈良好的线性关系。结论：在一定浓度范围内通过电化学方法测定油脂抗氧化剂含量的方法是可行的。     

固定云芝漆酶纳米金颗粒修饰金盘电极的制备及其对氧还原反应的生物电催化性能

利用1,6-己二硫醇作为联结剂将纳米金颗粒修饰到金盘电极上,再以L-半胱氨酸为修饰剂使纳米金颗粒功能化并进一步与漆酶充分作用,制备了固定漆酶的纳米金颗粒修饰金盘电极并以循环伏安法测试了其对氧还原的催化性能。实验结果表明:O2在该电极上还原电位约为-0.26 V(vs SCE),氧还原峰电流为3.0 uA(25℃),较文献[7]报导的固酶聚异丙基丙烯酰胺(PNIPAM)水凝胶修饰ITO电极的氧还原催化性能要优。(氧气还原电位:-0.26 V,vs NHE,峰电流:0.47 uA)进一步研究表明:本文制备的修饰电极稳定性好,适于长期使用而且热稳定性优于文献[7]报道的固酶聚异丙基丙烯酰胺水凝胶修饰ITO电极:50℃时在本文制备的纳米金修饰电极上氧还原峰电流仍保持为25℃时修饰电极上氧还原峰电流的40%左右。     

葡萄糖氧化酶在枯草芽孢杆菌芽孢表面的展示及其酶电极制备

葡萄糖生物传感器是目前最为常见的电化学生物传感器,绝大多数葡萄糖生物传感器采用在电极表面修饰葡萄糖氧化酶的方法来制备,但是,在电极的固定化过程中需要酶的纯化,使得成本增加,已成为固定化酶电极开发领域的瓶颈。文中主要以芽孢衣壳蛋白CotX为锚定蛋白将葡萄糖氧化酶 (Glucose oxidase,GOD) 展示到枯草芽孢杆菌芽孢表面,通过Western blotting分析、免疫荧光分析以及酶活检测均证明GOD在芽孢表面有效表达,发酵获得重组芽孢 (Spore-GOD)。再采用滴涂法和电沉积法制备了氧化石墨烯/普鲁士蓝沉积膜修饰玻碳电极,将Spore-GOD固定在修饰电极表面,最后滴加一层Nafion溶液,制成了电化学生物传感器,用于葡萄糖的灵敏测定。葡萄糖在该酶电极传感器上的循环伏安图表明,该反应在0.42 V处出现明显的氧化峰,并且氧化还原峰电流与葡萄糖浓度在0.1–7.0 mmol/L之间具有良好的线性关系,校正曲线方程为：I=1.304 7Cglucose+3.639 (R2=0.992 9),其检测限为7.5 μmol/L (S/N=3)。此修饰电极具有良好的导电性能、稳定性和重现性,可用于葡萄糖的分析测定。     

二茂铁－交联剂修饰的葡萄糖传感器

用牛血清白蛋白-戊二醛交联剂把葡萄糖氧化酶固定在Nafion-二茂铁修饰电极上,最后在电极上修饰一层Nafion膜,制备成葡萄搪传感器,电活性物质如抗坏血酸、尿酸等对葡萄糖的测定无干扰.该传感器的线性范围为5.0×10^-4-1.3×10^-2mol/L,响应时间小于60s.     

15-KETE对大鼠肺动脉平滑肌细胞钾离子通道的作用

目的观察15-酮基二十碳四烯酸(15-ketoeicosatetraenoic acid,15-KETE)对大鼠肺动脉平滑肌细胞(pulmonary arterial smooth muscle cells,PASMCs)膜电压门控钾离子通道(Kv)的作用,探讨其收缩肺动脉的离子通道机制。方法采用急性酶分离法(胶原酶Ⅰ型和弹性酶)获得健康成年SD大鼠单个PASMC,应用全细胞膜片钳记录方法,研究15-KETE对膜电位(Em)、膜电容(Cm)、电压门控钾电流(Ikv)的影响。结果①高浓度15-KETE(1×10-7mol/L、1×10-6mol/L)可引起PASMCs去极化,并且在细胞内钙被BAPTA缓冲后,15-KETE仍可引起PASMCs去极化,15-KETE对PASMC的膜电容无影响;②15-KETE(1×10-8~1×10-6mol/L)对Ikv的影响呈浓度依赖性和可逆性;③细胞内钙离子在生理浓度时([Ca2 ]i=75 nmol/L),15-KETE(1×10-6mol/L)对Ikv峰电流的抑制率显著高于细胞内无钙离子时。结论15-KETE可浓度依赖性的抑制Ikv,使常氧大鼠PASMCs去极化;细胞内钙离子加强了15-KETE对Ikv峰电流的抑制作用。     

非洲爪蟾卵母细胞GABA_B和GABA_C受体介导的电流反应

实验应用双电极电压箝技术 ,在具有滤泡膜的非洲爪蟾 (Xenopuslaevis)卵母细胞上记录到γ 氨基丁酸(γ aminobutyricacid ,GABA) 激活电流。此GABA 激活电流的特点及有关GABA受体类型的研究和分析如下 :( 1)在 3 5 5 % ( 5 5 / 15 5 )的受检细胞外加GABA可引起一慢的浓度依赖性的外向电流。 ( 2 )GABAA 受体的选择性拮抗剂bicuculline ( 10 -5mol/L)对GABA ( 10 -5mol/L)引起的外向电流无阻断作用 (n =6)。 ( 3 )GABAB 受体的选择性拮抗剂2 hydroxysaclofen ( 10 -4mol/L)能将GABA ( 10 -5mol/L)引起的外向电流可逆性地转变为内向电流 ,后者又可被GABAC 受体的选择性拮抗剂I4AA ( 10 -5mol/L)所消除 (n =6)。 ( 4 )GABAB 受体的特异性激动剂baclofen可引起部分 ( 2 0 % ,12 / 60 )受检细胞产生一慢的浓度依赖性的外向电流。 3× 10 -6 、3× 10 -5及 3× 10 -4mol/L 2 hydroxysaclofen分别阻断baclofen ( 10 -5mol/L) 激活电流 ( 6 3± 3 2 ) % ,( 4 4 1± 2 2 ) %及 ( 86 0± 1 6) % (n =6)。 ( 5 )baclofen激活电流的I V曲线显示逆转电位在 - 96 8± 7 2mV左右 ,此电流可分别被TEA ( 5mmol/L)和BaCl2 ( 2mmol/L)所阻断。以上结果提示 :在非洲爪蟾的卵母细胞上存在内源性GABAB 和GABAC 受体 ,GA     

黄曲霉毒素氧化酶/壳聚糖-单壁碳纳米管/聚邻苯二胺修饰电极对杂色曲霉素的检测

将黄曲霉毒素氧化酶(AFO)固定在壳聚糖(CS)-单壁碳纳米管(SWCNTs)杂交膜中,组装在聚邻苯二胺(POPD)修饰的金电极(Au)表面,制备了对杂色曲霉素(ST)敏感的生物传感器(AFO/CS-SWCNTs/POPD/Au)。运用原子力显微镜(AFM)、傅立叶变换红外光谱(FT-IR)和交流阻抗技术(EIS)对电极组装过程进行了表征。循环伏安法研究表明,AFO在修饰电极上发生了准可逆的氧化还原反应,是表面控制过程,其式量电位为-0.436V(vs.Ag/AgCl),说明包埋在CS-SWCNTs中的AFO和电极之间发生了直接电子传递。AFO修饰电极对ST具有明显的电催化作用,其表观米氏常数appKM为7.13μmol/L,催化电流与ST浓度在10～310ng/mL范围内呈线性关系,相关系数为0.997,检出限为3ng/mL(S/N=3),响应时间小于10s。组装的生物传感器具有较好的稳定性与重现性,连续检测20ng/mL的ST标准溶液11次,电流值RSD为3.9%;放置一个月后,其电流响应值仍为初始值的85.6%。该方法具有较高的选择性和灵敏度,应用于实际样品检测时,其回收率在87.6%～105.5%之间...     

心房肌胞内钙浓度变化对心房颤动患者小电导钙激活钾通道电流的影响

目的：SK通道存在于心肌细胞上,其中SK2亚型主要表达在心房。SK2通道对胞内游离钙离子高度敏感,可快速将钙离子浓度的变化转换成细胞膜电位变化。本实验应用穿孔膜片钳技术记录人心肌细胞SK2电流,观察心房肌细胞SK2电流在窦性患者和心房颤动患者之间的差别,以及电极液中不同的钙浓度对两组细胞SK2电流的影响。方法：将接受体外循环手术的患者分为两组：心房颤动组和窦性心律组。以心房肌细胞为研究对象,用穿孔膜片钳技术记录人心肌细胞电流,观察窦性组与房颤组SK2通道电流的差异以及两组细胞SK2电流对电极液中钙敏感性的不同。结果：在全细胞穿孔膜片钳模式下,电极液中游离钙离子浓度为5×10-7mol/L时,记录到房颤组SK2通道电流明显大于窦性组,尤其是在超极化水平。膜电位在-130 mV时,窦性组与房颤组的SK2通道电流密度分别为（-2.92±0.35）pA/pF（n=6）,（-6.83±0.19）pA/pF（n=3,P〈0.05）。在电极液游离钙离子浓度分别为0 mol/L、5×10-7mol/L、10-6mol/L,膜电位为-130 mV时,窦性组SK2通道电流密度分别为（-1.43±0.33）pA/pF（n=7）,（-2.92±0.35）pA/pF（n=6）,（-10.11±2.15）pA/pF（n=8,P〈0.05）;房颤组SK2通道电流密度分别为（-2.17±0.40）pA/pF（n=4）（-6.83±0.19）pA/pF（n=3）（-14.47±2.89）pA/pF（n=4）（P〈0.05）。结论：人心房肌细胞SK2通道具有电压不敏感、内向整流、apamin敏感的特性。电极液中钙浓度相同的情况下,房颤组的SK2电流密度明显大于窦性组,SK2通道电流对钙离子的敏感性高于窦性组,提示SK2通道钙敏感性增加可能与心房颤动的发生发展密切相关。     

精氨酸加压素对大鼠背根神经节神经元GABA激活电流的增强作用（英文）

越来越多的研究表明,精氨酸加压素(arginine vasopressin,AVP)在痛觉调制中具有镇痛作用。已报道的研究专注于AVP镇痛的中枢作用机制,而本研究旨在研究AVP镇痛的的外周作用机制。应用全细胞膜片钳技术,在急性分离的大鼠背根神经节(DRG)神经元上,观察AVP对GABA激活电流(IGABA)的增强作用以及AVP对GABAA受体功能的影响。结果显示,AVP(1×10-10~1×10-5 mol/L)预处理后,IGABA增大,GABA剂量效应曲线上移,IGABA的最大值较之对照增加约49.1%;而EC50值几乎不变,表示此种加强为非竞争性的,而且AVP对GABA电流的作用可能是电压非依赖性的。AVP对IGABA的加强作用几乎完全被V1a受体的拮抗剂SR49059(3×10-6 mol/L)阻断。二次钳压技术胞内透析非水解GDP类似物GDP-β-S(5×10-4 mol/L)或PKC抑制剂GF109203X(2×10-6 mol/L)也可以阻断AVP对IGABA的加强作用。以上结果提示,AVP经由G蛋白耦联受体以及PKC信号通路上调DRG神经元GABAA受体的功能,可能是其诱导镇痛作用的基础。     

Simultaneous voltammetric determination of norepinephrine, ascorbic acid and uric acid on polycalconcarboxylic acid modified glassy carbon electrode

A novel polycalconcarboxylic acid (CCA) modified glassy carbon electrode (GCE) was fabricated by electropolymerization and then successfully used to simultaneously determine ascorbic acid (AA), norepinephrine (NE) and uric acid (UA). The characterization of electrochemically synthesized Poly-CCA film was investigated by atomic force microscopy (AFM), electrochemical impedance spectroscopy (EIS) and voltammetric methods. It was found that the electrochemical behavior of the polymer-modified electrode depended on film thickness, i.e., the electropylmyerization time. Based on the electrochemical data, the charge transfer coefficient (alpha) and the surface coverage (Gamma) were calculated. This poly-CCA modified GCE could reduce the overpotential of ascorbic acid (AA), norepinephrine (NE) and uric acid (UA) oxidation in phosphate buffer solution (pH 6.0), while it increases the peak current significantly. The current peak separations of AA/NE, NE/UA and AA/UA on this modified electrode are 91mV, 256mV and 390mV in CV at 100mVs(-1), respectively. Therefore, the voltammetric responses of these three compounds can be well resolved on the polymer-modified electrode, and simultaneously determination of these three compounds can be achieved. In addition, this modified electrode can be successfully applied to determine AA and NE in injection and UA in urine samples without interferences.     

The electrochemical modification of clenbuterol for biosensors of dopamine, norepinephrine, adrenalin, ascorbic acid and uric acid at paraffin-impregnated graphite electrode

The electrochemical modification of clenbuterol (CLB) was studied at paraffin-impregnated graphite electrode (WGE) in two potential ranges of 0.0-1.6V and -1.2 to 1.2V. Various methods including X-ray photoelectron spectroscopy (XPS), UV-spectroelectrochemistry, infrared (IR) spectra and electrochemical techniques have been used to characterizing the modification. Clenbuterol can be modified at the electrode surface by carbon-nitrogen linkage or carbon-carbon linkage in 0.0-1.6V or -1.2 to 1.2V, respectively. The electrochemical behaviors of dopamine (DA), norepinephrine (NE), adrenalin (EP), ascorbic acid (AA) and uric acid (UA) were studied at clenbuterol-modified paraffin-impregnated graphite electrode (CLB/WGE), and it was found that all these compounds could be detected successfully.     

A novel sensor based on electrochemical polymerization of diglycolic acid for determination of acetaminophen

Diglycolic acid (DA) polymer was coated on glassy carbon (GC) electrode by cyclic voltammetry (CV) technique for the first time. The electrochemical performances of the modified electrode were investigated by CV and electrochemical impedance (EIS). The obtained electrode showed an excellent electrocatalytic activity for the oxidation of acetaminophen (ACOP). A couple of well-defined reversible electrochemical redox peaks were observed on the ploy(DA)/GC electrode in ACOP solution. Compared with bare GC electrode, the oxidation peak potential of ACOP on ploy(DA)/GC electrode moved from 0.289 V to 0.220 V. Meanwhile, the oxidation peak current was much higher on the modified electrode than that on the bare GC electrode, indicating DA polymer modified electrode possessed excellent performance for the oxidation of ACOP. This kind of capability of the modified electrode can be enlisted for the highly sensitive and selective determination of ACOP. Under the optimized conditions, a wide linear range from 2 × 10(-8) to 5.0 × 10(-4)M with a correlation coefficient 0.9995 was obtained. The detection limit was 6.7 × 10(-9)M (at the ratio of signal to noise, S/N=3:1). The modified electrode also exhibited very good stability and reproducibility for the detection of ACOP. The established method was applied to the determination of ACOP in samples. An average recovery of 100.1% was achieved. These results indicated that this method was reliable for determining ACOP.     

Electrochemical selective determination of ascorbic acid at redox active polymer modified electrode derived from direct blue 71

A simple selective method for determination of ascorbic acid using polymerized direct blue 71 (DB71) is described. Anodic polymerization of the azo dye DB71 on glassy carbon (GC) electrode in 0.1M H(2)SO(4) acidic medium was found to yield thin and stable polymeric films. The poly(DB71) films were electroactive in wide pH range (1-13). A pair of symmetrical redox peaks at a formal redox potential, E('0)=-0.02V vs. Ag/AgCl (pH 7.0) was observed with a Nernstian slope -0.058V, is attributed to a 1:1 proton+electron involving polymer redox reactions at the modified electrode. Scanning electron microscope (SEM), atomic force microscope (AFM) and electrochemical impedance spectroscopy (EIS) measurements were used for surface studies of polymer modified electrode. Poly(DB71) modified GC electrode showed excellent electrocatalytic activity towards ascorbic acid in neutral buffer solution. Using amperometric method, linear range (1x10(-6)-2x10(-3)M), dynamic range (1x10(-6)-0.01M) and detection limit (1x10(-6)M, S/N=3) were estimated for measurement of ascorbic acid in pH 7.0 buffer solution. Major interferences such as dopamine and uric acid are tested at this modified electrode and found that selective detection of ascorbic acid can be achieved. This new method successfully applied for determination of ascorbic acid in commercial tablets with satisfactory results.     

Identification and quantitative determination of uric acid in human urine and plasma by capillary electrophoresis with amperometric detection

Application of capillary zone electrophoresis with electrochemical detection to the identification and quantitative determination of uric acid in human urine as well as plasma is described. This work was carried out in a 30 cm×25 μm I.D. fused-silica capillary with tricine buffer and a carbon fiber bundle was employed as a working electrode, the working voltage in amperometric detection was set at +0.80 V (vs. SCE). The sample constituent is identified by stopped flow-linear sweep voltammetry. Under optimal conditions, a lower detection limit of 0.48 fmol was obtained for uric acid.     

Electrochemical synthesis of polyaniline nano-networks on p-aminobenzene sulfonic acid functionalized glassy carbon electrode Its use for the simultaneous determination of ascorbic acid and uric acid

A composite film of polyaniline (PAN) nano-networks/p-aminobenzene sulfonic acid (ABSA) modified glassy carbon electrode (GCE) has been fabricated via an electrochemical oxidation procedure and applied to the electro-catalytic oxidation of uric acid (UA) and ascorbic acid (AA). The ABSA monolayer at GCE surface has been characterized by X-ray photo-electron spectroscopy (XPS) and electrochemical techniques. Atomic force microscopy (AFM), field emission scanning electron microscope (SEM), electrochemical impedance spectroscopy (EIS), UV-visible absorption spectra (UV-vis) and cyclic voltammetry (CV) have been used to investigate the PAN-ABSA composite film, which demonstrates the formation of the composite film and the maintenance of the electroactivity of PAN in neutral and even in alkaline media. Due to its different catalytic effects towards the electro-oxidation of UA and AA, the modified GCE can resolve the overlapped voltammetric response of UA and AA into two well-defined voltammetric peaks with both CV and differential pulse voltammetry (DPV), which can be used for the selective and simultaneous determination of these species in a mixture. The catalytic peak currents are linearly dependent on the concentrations of UA and AA in the range of 50-250 and 35-175mumoll(-1) with correlation coefficients of 0.997 and 0.998, respectively. The detection limits for UA and AA are 12 and 7.5mumoll(-1), respectively. Besides the good stability and reproducibility of PAN-ABSA/GCE due to the covalent attachment of ABSA at GCE surface, the modified electrode also exhibits good sensitivity and selectivity.     

A cyclodextrin host-guest recognition approach to an electrochemical sensor for simultaneous quantification of serotonin and dopamine

An electrochemical sensor for simultaneous quantification of serotonin (5-hydroxytryptamine, 5-HT) and dopamine (DA) using a β-cyclodextrin/poly(N-acetylaniline)/carbon nanotube composite modified carbon paste electrode has been developed. Synergistic effect of multi-walled carbon nanotube (MWCNT) in addition to the pre-concentrating effect of β-cyclodextrin (β-CD) as well as its different inclusion complex stability with 5-HT and DA was used to construct an electrochemical sensor for quantification of these important neurotransmitters. The overlapping anodic peaks of 5-HT and DA at 428 mV on bare electrode resolved in two well-defined voltammetric peaks at 202 and 363 mV vs. Ag/AgCl respectively. The oxidation mechanism of 5-HT and DA on the surface of the electrode was investigated by cyclic voltammetry and it was found that the electrode processes are pH dependent and electrochemical oxidation of 5-HT is totally irreversible while the electrode gave a more reversible process to DA. Under optimized conditions, linear calibration curves were obtained in the range of about 4-200 μM with a detection limits down to sub-μM levels (S/N=3) after 20-s accumulation, for both. The proposed sensor was shown to be remarkably selective for 5-HT and DA in matrices containing different species including ascorbic acid and uric acid. The suitability of the developed method was tested for the determination of 5-HT and DA in the Randox Synthetic Plasma samples and acceptable recoveries were obtained for a set of spiked samples.     

Highly selective and sensitive determination of dopamine using a Nafion/carbon nanotubes coated poly(3-methylthiophene) modified electrode

A poly(3-methylthiophene) modified glassy carbon electrode coated with Nafion/single-walled carbon nanotubes film was fabricated and used for highly selective and sensitive determination of dopamine. The hybrid film surface of the modified electrode was characterized by scanning electrochemical microscopy (SECM) and the results indicated that the carbon nanotubes were dispersed uniformly on the conductive polymer. The experimental results suggest that the hybrid film modified electrode combining the advantages of poly(3-methylthiophene), carbon nanotubes with Nafion exhibits dramatic electrocatalytic effect on the oxidation of dopamine (DA) and results in a marked enhancement of the current response. In 0.1M phosphate buffer solution (PBS) of pH 7.0, the differential pulse voltammetric (DPV) peak heights are linear with DA concentration in three intervals, viz. 0.020-0.10 microM, 0.10-1.0 microM and 1.0-6.0 microM, with correlation coefficients of 0.9993, 0.9996 and 0.9993, respectively. The detection limit of 5.0 nM DA could be estimated (S/N=3). Moreover, the interferences of ascorbic acid (AA) and uric acid (UC) are effectively diminished. This hybrid film modified electrode can be applied to the determination of DA contents in dopamine hydrochloride injection and human serum. These attractive features provide a potential application for either in vitro measurement of DA in the presence of excess AA and UA or as detectors in flow injection analysis (FIA) and high performance liquid chromatography (HPLC).     

Electrochemical performance of 8-hydroxy-2'-deoxyguanosine and its detection at poly(3-methylthiophene) modified glassy carbon electrode

8-Hydroxy-2'-deoxyguanosine (8-OH-dG) has attracted enormous attention in recent years because it has been acknowledged as a typical biomarker of oxidative DNA damage. In this paper, the electrochemical performance of 8-OH-dG at the poly(3-methylthiophene) (P3MT) modified glassy carbon electrode (GCE) was investigated by cyclic voltammetry (CV) and linear sweep voltammetry (LSV). The conducting polymer P3MT can effectively decrease the oxidation peak potential of 8-OH-dG and greatly enhance its peak current. In 0.1 M pH 7.0 phosphate buffer solution (PBS), the anodic peak currents of cyclic voltammograms are linear with the 8-OH-dG concentration in two intervals, viz. 0.700-35.0 microM and 35.0-70.0 microM, with the correlative coefficients of 0.9992 and 0.9995, respectively. The detection limit of 8-OH-dG can be estimated to be 0.100 microM (S/N=3). This modified electrode can be used to detect the amount of 8-OH-dG in human urine. Furthermore, the effects of scan rate, pH, and interference of uric acid (UA) for the voltammetric behavior and detection of 8-OH-dG are also discussed. This proposed modified electrode also shows excellent reproducibility and stability that makes it an ideal candidate for amperometric detection of 8-OH-dG in flow injection analysis (FIA) and high performance liquid chromatography (HPLC).     

Hollow nitrogen-doped carbon microspheres pyrolyzed from self-polymerized dopamine and its application in simultaneous electrochemical determination of uric acid, ascorbic acid and dopamine

Hollow nitrogen-doped carbon microspheres (HNCMS) as a novel carbon material have been prepared and the catalytic activities of HNCMS-modified glassy carbon (GC) electrode towards the electro-oxidation of uric acid (UA), ascorbic acid (AA) and dopamine (DA) have also been investigated. Comparing with the bare GC and carbon nanotubes (CNTs) modified GC (CNTs/GC) electrodes, the HNCMS modified GC (HNCMS/GC) electrode has higher catalytic activities towards the oxidation of UA, AA and DA. Moreover, the peak separations between AA and DA, and DA and UA at the HNCMS/GC electrode are up to 212 and 136 mV, respectively, which are superior to those at the CNTs/GC electrode (168 and 114 mV). Thus the simultaneous determination of UA, AA and DA was carried out successfully. In the co-existence system of UA, AA and DA, the linear response range for UA, AA and DA are 5-30 μM, 100-1000 μM and 3-75 μM, respectively and the detection limits (S/N = 3) are 0.04 μM, 0.91 μM and 0.02 μM, respectively. Meanwhile, the HNCMS/GC electrode can be applied to measure uric acid in human urine, and may be useful for measuring abnormally high concentration of AA or DA. The attractive features of HNCMS provide potential applications in the simultaneous determination of UA, AA and DA.