海金沙草粗多糖提取工艺的响应面优化

为获得海金沙草粗多糖最佳提取工艺,利用Plackett-Burman试验对提取工艺进行了初步优化研究,根据PB设计主效应分析结果进行了爬陡坡试验进一步逼近优化区域,最后用Box-Behnken设计进行了响应面优化并获得了提取工艺多项式数学模型,即y=12.27-0.027x1-0.065x2-0.039x3-0.20x...     

响应面法优化合萌总黄酮提取工艺

目的:利用响应面法优化合萌中总黄酮的提取工艺条件。方法:通过单因素试验分别考察提取时间、乙醇体积分数、液固比、提取温度及提取次数对合萌总黄酮得率的影响,并选取提取时间、乙醇体积分数、液固比、提取温度为影响因子,应用响应面法优化提取工艺。结果:合萌总黄酮的最佳提取条件为:提取时间60 min,乙醇浓度65%,液固比(g∶m L)25∶1,提取温度90℃,在此条件下,合萌总黄酮得率为4.08 mg/g,接近模型预测值4.11 mg/g。结论:响应面法在一定程度上可以提高合萌总黄酮得率,表明响应面法用于合萌总黄酮提取工艺的优化具有可行性。     

响应面法优化回流提取紫薯花青素工艺

旨在获得紫薯花青素的最佳提取工艺,采用中心组合(Box-Behnken)试验设计及响应面分析相结合的方法,对紫薯花青素的回流提取工艺进行优化。单因素试验结果显示,最佳乙醇体积浓度为75%、提取温度为60℃、提取时间为60 min、液料比为7∶1,在此基础上,利用中心组合(Box-Behnken)试验设计及响应面分析法进行回归分析,获得最优工艺参数为:乙醇体积浓度74%、提取温度66℃、提取时间56 min、液料比8∶1。在优化后的条件下进行验证试验,得到紫薯花青素的提取率为4.64mg/g,与理论值(4.68 mg/g)相比,相对误差较小,为0.85%。研究表明,采用响应面法分析优化紫薯花青素的水浴回流提取工艺参数准确可靠,可应用于紫薯花青素的提取生产。     

Box-Behnken响应面法优化余甘子总多酚超声提取工艺

以余甘子中总多酚的提取量为评价指标,通过单因素试验结合Box-Behnken响应面法,研究乙醇浓度、超声时间、超声温度对余甘子中总多酚提取工艺的影响,并优化提取工艺。结果表明：影响余甘子总多酚提取的因素主次为乙醇浓度>超声温度>超声时间,最佳提取工艺为乙醇浓度64%、超声时间39 min、提取温度43 ℃。验证试验中总多酚提取量为186.17 mg/g,与模型预测值190.33 mg/g较接近。Box-Behnken响应面回归方程拟合度良好,适合用于余甘子总多酚提取工艺的回归分析和参数优化。     

纤维素酶解-超声偶联法提取葛根中总异黄酮的工艺优化

采用酶解-超声偶联新工艺对葛根中总异黄酮提取进行优化,以提高其收率.在单因素试验的基础上,利用Box-Behnken响应面试验设计,以蒸馏水作为提取溶剂,对温度、酶浓度、时间进行三因素三水平的试验设计优化.结果表明最佳提取工艺条件为:温度34℃、酶浓度0.63 mg/mL、时间62 min.在此条件下,葛根总异黄酮提取率为7.10％,与预测值的相对误差为0.34％.酶解-超声偶联工艺是一种新型、快速、有效的总黄酮提取方法.     

响应面法优化酶解辅助提取翅果油树叶总黄酮

利用酶辅助法对翅果油树(Elaeagnus mollis Diels)叶中总黄酮的提取工艺进行优化。在单因子试验结果的基础上,采用响应面法(RSM)研究了酶用量、酶解时间、pH值和酶解温度对翅果油树叶总黄酮提取得率的影响。结果表明:纤维素酶具有较好的酶解能力,当酶用量为6.5 mg.g-1,酶解时间为1.5 h,pH4.7,温度为46℃时,总黄酮得率达到7.1%。     

响应曲面法优化菌丝体中红曲色素的提取条件

以红曲菌丝体为原料,通过单因素实验及Box-Behnken设计响应曲面分析优化了红曲色素的提取工艺条件。通过实验,得到了提取率的回归方程Y=0.923-0.011X1-0.011X2-0.017X12-0.027X22-0.026X32-0.028X1X2-0.019X1X3,通过对模型解逆矩阵得优化方案:乙醇浓度X1=66%、超声功率X2=200 w、提取温度X3=52℃,模型预测结果为92.5%。在该工艺条件下进行验证实验,提取率达到92.1±0.6%(n=3)。     

虎耳草中抗氧化活性物质的提取及成分研究

对虎耳草中抗氧化活性物质提取工艺进行优化研究并对其进行总黄酮、总多酚、多糖的含量测定。通过单因素试验和Box-Behnken设计,以虎耳草中抗氧化活性物质对DPPH.自由基的清除率为响应值,利用响应面分析法对提取参数进行优化。结果表明:在提取温度39℃、料液比1∶40.5(g/mL)、提取时间3.7 min,微波功率500 W的优化条件下,以水为提取溶剂时,其提取液对DPPH.的清除率达到最大,为80.32%,同时将该提取液进行成分分析,1 g提取液中含有总黄酮11.30 mg,总多酚20.27 mg,多糖55.85 mg。     

响应面法优化益母草总黄酮的提取工艺研究

采用响应面法优化超声提取益母草总黄酮的工艺条件。方法:在超声时间、超声功率、超声温度、料液比等单因素的基础上,通过中心组合设计原理采用三因子三水平的响应面分析法设计,对单因子显著性和交互作用进行分析。结果:超声提取益母草总黄酮的最佳工艺条件为:超声时间35.54 min,料液比1∶30.63,乙醇浓度73.41%。此时吸光度为0.295 9。在此条件下益母草的总黄酮提取率为1.21%。结论:优化的提取工艺条件,益母草的总黄酮提取率高,节约资源。     

超声辅助提取凤丹籽总黄酮的工艺研究

本文以经脱脂处理后的凤丹籽为原料,在单因素实验的基础上,选取乙醇浓度、料液比、超声时间和超声功率为自变量,以总黄酮得率为响应值,采用Box-Behnken响应面设计分析方法优化凤丹籽总黄酮的提取工艺。通过此模型得出:超声时间对凤丹籽总黄酮提取的影响最为显著,超声时间和乙醇浓度,超声时间和料液比,超声时间和超声功率之间的交互作用显著。模型预计凤丹籽总黄酮提取的最佳工艺条件为:乙醇浓度75%,料液比1:21 g/mL,超声时间49 min,超声功率240 w,在此条件下,总黄酮得率平均值为9.015 mg/g。     

Optimization of the Cellulase−Ultrasonic Synergistic Extraction Conditions of Polysaccharides from Lenzites betulina

Lenzites betulina has been recognized as a rich source of chemical components, including polysaccharides, sterides and sugar alcohols. In this study, cellulase?ultrasonic synergistic extraction method was applied to extract polysaccharides from L. betulina, and the response surface methodology was used to optimize the extraction conditions. The eight basic factors affecting extraction yield were evaluated by Plackett?Burman design (PBD). Then, the four important factors significantly affecting the yield of polysaccharides from L. betulina, including enzymolysis temperature, enzymolysis time, ultrasound time and ultrasound temperature, were optimized by Box?Behnken design (BBD). Maximum extraction yield of L. betulina polysaccharides was 13.64±0.09 % at a cellulase dosage of 0.8 %, enzymolysis temperature of 60 °C, enzymolysis time of 180 min, pH of 4.5, liquid‐solid ratio of 45 ml/g, ultrasound power of 300 W, ultrasound time of 20 min and ultrasound temperature of 45 °C. Subsequently, the characteristic structure of crude polysaccharides was determined by FT‐IR. Results indicated that cellulase?ultrasonic synergistic treatment is suitable for L. betulina polysaccharides extraction, and it has good prospect for development and utilization.     

Nutrient improvement using statistical optimization for growth of Schizophyllum commune, and its antifungal activity against wood degrading fungi of rubberwood

Two statistical tools, Plackett-Burman design (PBD) and Box-Behnken design (BBD) were used to optimize the mycelia growth of Schizophyllum commune with different nutrient components. Results showed that 32.92 g/L of biomass were produced using a medium consisting of 18.74 g/L yeast extract, 38.65 g/L glucose, and 0.59 g/L MgSO(4).7H(2)O. The experimental data fitted well with the model predicted values within 0.09 to 0.77% error. The biomass was also tested for antifungal activity against wood degrading fungi of rubberwood. Results showed that the minimum inhibitory concentration (MIC) values for antifungal activity range from 0.16 to 5.00 μg/μL. The GC-MS analysis indicated that this fungus produced several compounds, such as glycerin, 2(3H)-furanone, 5-heptyldihydro-, 4H-pyran-4-one, 2,3-dihydro-3,5-dihydroxy-6-methyl-, and triacetin.     

Optimization and characterization of rhamnolipid production by Pseudomonas aeruginosa NY3 using waste frying oil as the sole carbon

Yield and cost are two major factors limiting the widespread use of rhamnolipids (RLs). In the present study, waste frying oil (WFO) was used as the sole carbon source to produce environmentally friendly RLs by Pseudomonas aeruginosa NY3. The Plackett–Burman design (PBD) and Box–Behnken design (BBD) methods were used to maximize the production yield of RL. The PBD results showed that the concentrations of NaNO₃, Na₂HPO₄, and trace elements were the key factors affecting the yield of RL. Furthermore, the BBD results showed that at NaNO₃, Na₂HPO₄, and trace elements concentrations were 4.95, 0.66, and 0.64 mL/L, respectively, the average RL yield reached 9.15 ± 0.52 g/L, 1.58-fold higher than that observed before optimization. Fourier transform infrared spectroscopy (FTIR) and liquid chromatography-ion trap-time of flight mass spectrometry (LCMS-IT-TOF) were used to elucidate the diversity of RL congeners. The results showed that, after optimization, the RL congener diversity increased, and the major RL constituent was converted from di-RLs (64.04%) to mono-RLs (60.44%). These results suggested that the concentrations of the components contained in the culture medium of P. aeruginosa NY3 influenced not only the yield of RL, but also its congener distribution.     

Optimization of 2,3-dihydroxybiphenyl 1,2-dioxygenase expression and its application for biosensor

In this study, two statistical experimental designs, Plackett-Burman design (PBD) and response surface methodology (RSM), were employed to enhance the expression of 2,3-dihydroxybiphenyl 1,2-dioxygenase (BphC_LA-4), which was subsequently used for the construction of catechol biosensor. Ten important factors were evaluated by PBD, and four significant parameters were then optimized by RSM. Under the favorable fermentation conditions, the maximal specific activity of BphC_LA-4 was about 0.58U/mg with catechol as substrate. Meanwhile, homology modeling and molecular docking were utilized to help understand the interaction between BphC_LA-4 and catecholic substrates, which illustrated that BphC_LA-4 presented lower binding affinity towards 4-methylcatechol in comparison with 3-methylcatechol and catechol. Interestingly, the BphC_LA-4 enzyme electrode prepared by SiO2 sol-gel showed good response to all these three catecholic compounds. The differences of selectivity to 4-methylcatechol between free and immobilized enzyme implied that the introduction of electro-catalysis might have an effect on the enzyme-catalysis process.     

Plackett-Burman Design与均匀设计法优化玫瑰色微球菌固定化脱氮的性能

【目的】采用Plackett-Burman Design (PBD)与均匀设计(Uniform Design, UD) 优化玫瑰色微球菌(Micrococcus roseus)固定化脱氮的条件,以提高其脱氮性能。【方法】选择聚乙烯醇(Polyvinyl alcohol,PVA)与海藻酸钠(Sodium alginate,SA)作为固定化细胞材料,研究其成球方式与性能,应用PBD对9个影响脱氮效果的因素进行显著性检验,筛选出PVA、SA、温度、菌液接种量、菌球量5个显著性因素(P<0.05)。采用UD对5个显著因素进行条件优化,优化数据通过Minitab与Matlab软件进行逐步回归分析,并建立二阶多项式模型。【结果】最优脱氮条件为PVA 9.6%、SA 2.2%、温度33.4 °C、菌液接种量8%、菌球量500个/100 mL,连续脱氮72 h,最高脱氮率达到60.9%。【结论】PBD与UD的联合使用能够在显著因子筛选与寻优中发挥重要的作用。连续脱氮试验表明,玫瑰色微球菌去除氨氮主要通过同化、硝化与反硝化途径。     

Mutations of Gln64 in the HIV-1 gp41 N-terminal heptad repeat render viruses resistant to peptide HIV fusion inhibitors targeting the gp41 pocket

To prove that the peptidic HIV-1 fusion inhibitors containing the pocket-binding domain (PBD) mainly target the hydrophobic pocket in the gp41 N-terminal heptad repeat (NHR), we constructed pseudoviruses by replacement of Q64 in the gp41 pocket region with Ala (Q64A) or Leu (Q64L). These viruses were highly resistant to C34 and CP32M containing the PBD, while they were susceptible to T20 (enfuvirtide) lacking the PBD but containing the GIV-motif-binding domain (GBD) and lipid-binding domain (LBD). They were also sensitive to C52L, which contains the PBD, GBD, and LBD. Those mutations may disrupt the hydrophilic interaction between Q64 in the NHR and N113 in the peptides containing the PBD. This report provides insights into the mechanisms of drug resistance, with implications for the design of novel HIV fusion and entry inhibitors.     

Determination of experimental domain factors of polyphenols,phenolic acids and flavonoids of lemon (Citrus limon) peel using two-level factorial design

This study aimed to evaluate the significant extraction factors in achieving higher recovery yield of total polyphenols, phenolic acids and flavonoids content from Citrus limon peel using two-level factorial design. The effect of five independent factors including drying temperature (40–60 °C), methanol concentration (20–60%), extraction temperature (28–60 °C), extraction time (30–60 min) and storage duration (0–14 days) were evaluated. Among all the examined factors, results showed that drying temperature, storage duration and extraction temperature were the most significant and contributing factors affecting the total polyphenols, phenolic acids and flavonoids content of lemon peel at P < 0.05. On the contrary, methanol concentration and extraction time exhibited the least significant and contribution at P greater than 0.05. In conclusion, the experimental domain factors were successfully obtained from this experiment, Therefore, further study on optimization of the obtained factors will be conducted in the future study using response surface methodology.