树干毕赤酵母NLP31发酵产乙醇的研究

研究了树干毕赤酵母NLP31在木糖质量浓度为45 g/L的3种发酵培养基Ⅰ、Ⅱ和Ⅲ上发酵3轮的发酵性能以及在45 g/L木糖或混合糖(葡萄糖30 g/L,木糖15 g/L)的发酵培养基Ⅲ上的代谢历程。结果表明:树干毕赤酵母NLP31在发酵培养基Ⅲ上,乙醇浓度和乙醇得率均达到最高,分别为(17.29±0.15)g/L和(84.65±0.58)%。在45 g/L木糖或混合糖(葡萄糖30 g/L,木糖15 g/L)的发酵培养基Ⅲ上的代谢历程表明:混合糖发酵达到最大乙醇得率的时间仅为12 h,要比单一木糖发酵缩短了8 h。树干毕赤酵母NLP31在以廉价的无机N源为发酵培养基上的乙醇发酵性能高,能够降低燃料乙醇的生产成本。     

木糖发酵生产乙醇的研究

选育出一株优良的木糖发酵菌株树干毕赤酵母菌7124,并利用纯木糖优化了木糖发酵条件,利用海藻酸钠固定化树干毕赤酵母菌增殖细胞,不仅能较好满足限氧发酵条件,而且能耐较高糖浓度,使乙醇发酵浓度提高到20g/L。利用半纤维素水解液进行了乙醇发酵的初步研究,基本达到了纯木糖发酵的效果。     

高浓度糖发酵制备乙醇

以树干毕赤酵母为发酵菌株,混合糖（木糖、葡萄糖）为发酵底物,通过培养基和培养条件的改变来确定树干毕赤酵母高糖浓度发酵时所需的条件。研究结果表明：在24h发酵周期内初始木糖质量浓度为63．0g／L较适宜;在36h发酵周期内初始木糖质量浓度为72．0g/L较适宜。24h发酵周期内,在36．0g／L木糖中添加的葡萄糖质量浓度以54．0g/L为最佳,发酵结束乙醇质量浓度达32．9g／L;36h发酵周期内,添加的葡萄糖质量浓度以72．0g／L为最佳,发酵结束乙醇质量浓度为36．9g／L。以（NH4）2SO4为N源时较适合戊糖发酵制备乙醇,（NH2）2SO4的最佳质量浓度为1．1g／L。发酵前8h摇床转速为90r／min,后16h为150r／min,乙醇质量浓度较高,可达17．5g/L。     

分批补料对木糖发酵生产乙醇的影响

以树干毕赤酵母为发酵菌种,纯木糖为发酵底物,通过分批补料来提高糖利用率以及乙醇得率。结果表明,在24h内,最佳初始木糖浓度为80g/L,在28h的发酵周期中,可以将木糖浓度提高至90g/L,在32h发酵周期内可以将木糖浓度提高至100g/L。通过分批补料,乙醇浓度得到明显提高。当总糖浓度分别为80g/L、90g/L时,24h发酵周期内,分批补料次数以1次为宜,乙醇浓度分别达30.95g/L、32.60g/L,相比于不补料即一次性投料,乙醇浓度分别提高了9.36%、9.18%。总糖浓度100g/L,28h发酵周期内,补料2次效果最佳,乙醇浓度达37.49g/L,比一次性投料下提高了10.36%,较一次性投料达到相同发酵效果缩短了4h。     

萃取耦合技术对玉米秸秆水解液发酵产丁醇的影响

本研究以玉米秸秆水解液为原料,通过萃取发酵技术生产燃料丁醇,以提高丁醇产量,降低生产成本。通过对萃取剂的筛选与条件优化,确定纤维丁醇发酵的萃取剂为油醇,添加时间为发酵0 h,添加比例为1:1 (V/V)。该条件下发酵32 g/L糖浓度的玉米秸秆水解液,丁醇和总溶剂产量分别为3.28 g/L和4.72 g/L,比对照分别提高958.1%和742.9%。以D301树脂脱毒后5%总糖浓度的玉米秸秆水解液进行丁醇萃取发酵,丁醇和总溶剂产量分别达到10.34 g/L和14.72 g/L,发酵得率为0.31 g/g,与混合糖发酵结果相当。研究结果表明萃取发酵技术能够显著提高原料的利用率和丁醇产量,为纤维丁醇工业化生产提供了技术支撑。     

丙酮丁醇梭菌发酵菊芋汁生产丁醇

对丙酮丁醇梭菌Clostridium acetobutylicum L7发酵菊芋汁酸水解液生产丁醇进行了初步研究。实验结果表明,以该水解液为底物生产丁醇,不需要添加氮源和生长因子。当水解液初始糖浓度为48.36 g/L时,其发酵性能与以果糖为碳源的对照组基本相同,发酵终点丁醇浓度为8.67 g/L,丁醇、丙酮和乙醇的比例为0.58∶0.36∶0.06,但与以葡萄糖为碳源的对照组相比,发酵时间明显延长,表明该菌株葡萄糖转运能力强于果糖。当水解液初始糖浓度提高到62.87 g/L时,发酵终点残糖浓度从3.09 g/L增加到3.26 g/L,但丁醇浓度却提高到11.21 g/L,丁醇、丙酮和乙醇的比例相应为0.64∶0.29∶0.05,表明适量糖过剩有助于C.acetobutylicum L7胞内代谢从丙酮合成向丁醇合成途径调节;继续提高水解液初始糖浓度,发酵终点残糖浓度迅速升高,丁醇生产的技术经济指标受到明显影响。     

休哈塔假丝酵母乙醇发酵性能的研究

木糖的高效发酵是制约纤维素燃料乙醇生产的技术瓶颈之一,高性能发酵菌种的开发是本领域研究的重点。以木糖发酵的典型菌株休哈塔假丝酵母为材料,研究氮源配比、葡萄糖和木糖初始浓度、葡萄糖添加及典型抑制物等因素对其木糖利用和乙醇发酵性能的影响规律。结果表明,硫酸铵更适宜于木糖和葡萄糖发酵产乙醇。在摇瓶振荡发酵条件下,该酵母可发酵164.0 g/L葡萄糖生成61.9 g/L乙醇,糖利用率和乙醇得率分别为99.8%和74.0%;受酵母细胞膜上转运体系的限制,对木糖的最高发酵浓度为120.0 g/L,可生成45.7 g/L乙醇,糖利用率和乙醇得率分别达到94.8%和87.0%。休哈塔假丝酵母发酵木糖的主要产物为乙醇,仅生成微量的木糖醇;添加葡萄糖可促进木糖的利用;休哈塔假丝酵母在葡萄糖发酵时的乙酸和甲酸的耐受浓度分别为8.32和2.55 g/L,木糖发酵时的乙酸和甲酸的耐受浓度分别为6.28和1.15 g/L。     

采用玉米秸秆水解糖和玉米浆发酵生产丁二酸

研究了以玉米秸秆水解糖为碳源,不同氮源条件下琥珀酸放线杆菌Actinobacillus succinogenesSF-9的丁二酸发酵产酸能力。结果表明玉米浆可以替代酵母膏作为丁二酸发酵的廉价氮源。厌氧摇瓶丁二酸发酵单因素试验,得到在初糖浓度50 g/L时,玉米浆的较佳用量为20 g/L。在5 L搅拌罐上,考察了不同初始玉米秸秆水解糖浓度对A.succinogenes SF-9发酵生产丁二酸的影响,结果显示高初始秸秆糖浓度对琥珀酸放线杆菌的生长有抑制作用。采用补料分批发酵,发酵60 h丁二酸的产量达到42.7g/L,丁二酸产率82.7%,生产强度0.81 g/(L·h)。丁二酸的产量和生产强度较分批发酵有明显提高。     

圆红冬孢酵母利用生物乙醇废水-木薯粉水解液发酵产油

【目的】获得能够高效降解生物乙醇废水化学需氧量(COD)的圆红冬孢酵母菌株,评估废水初始COD浓度对驯化菌株生长的影响,将木薯粉生产微生物油脂和高浓度有机废水降解过程整合,以生物乙醇废水为水源制备生物乙醇废水-木薯粉水解液培养基,明确产油效率高、生物乙醇废水COD降解率高的初始还原糖浓度。【方法】采用在高浓度的生物乙醇废水中进行多次驯化的方法,获得能够适应废水环境的圆红冬孢酵母菌株;采用双酶水解法对加入乙醇废水中的木薯粉进行水解;采用重量法监测生物量浓度变化,采用酸热法提取油脂,重铬酸钾法监测COD,DNS法测定废水还原糖浓度,凯氏定氮法测定总氮,钼酸铵比色法测定总磷。【结果】通过驯化筛选得到一株能耐受高浓度生物乙醇废水的优势菌株Rhodosporidium toruloides D5。以未稀释的废水为培养基,驯化菌株的最终生物量浓度和COD降解率分别为3.8 g/L和75.0%。采用生物乙醇废水-木薯粉水解液发酵时,控制初始还原糖浓度低于30 g/L时,生物量浓度和油脂浓度随初始还原糖浓度的升高而升高,均在120 h时达到最高COD降解率,初始还原糖浓度对达到的最大COD降解率无明显影响,废水N、P去除率分别达到99%和92%以上。【结论】在未经稀释的高浓度生物乙醇废水中可获得较高的生物量浓度;采用高浓度生物乙醇废水-木薯粉水解液培养基发酵产油,初始还原糖浓度为30 g/L,可在保证高油脂产量的同时,实现废水COD的高效降解,有效回收利用废水中残余的N、P源,从而降低微生物油脂生产和废水处理成本,研究结果可为开发廉价微生物油脂生产技术提供有用的参考。     

一株葡萄糖和木糖共发酵高效产乙醇重组运动发酵单胞菌的性能评价

木糖是木质纤维素原料水解液中的第二大组分,木糖和葡萄糖的充分利用是有经济性地生产纤维素乙醇的关键。通过基因克隆手段构建了一株可以高效利用木糖产乙醇的重组运动发酵单胞菌Zymomonas mobilis TSH01,并进行了利用单糖溶液、混合糖溶液及玉米秸秆水解液发酵产乙醇效率的研究。结果表明,利用单一葡萄糖或单一木糖溶液发酵时,当糖浓度为8%、发酵72 h后,糖利用率分别为100%和98.9%,乙醇代谢收率分别为87.8%和78.3%;利用8%葡萄糖和8%木糖的混合溶液发酵时,72 h后,葡萄糖和木糖的利用率分别为98.5%和97.4%,乙醇代谢收率为94.9%。利用含3.2%葡萄糖和3.5%木糖的玉米秸秆水解液发酵72 h后,葡萄糖和木糖的利用率分别为100%和92.3%,乙醇代谢收率为91.5%。此外,磷酸二氢钾对发酵过程中木糖利用率以及乙醇收率的提高有明显促进作用。     

一株拜氏梭菌利用甘蔗废糖蜜发酵生产丙酮丁醇

以甘蔗废糖蜜作为原料,利用Clostridium beijerinckii DSM 6422菌株进行丙酮丁醇发酵的初步研究.结果表明:采用H2SO4预处理糖蜜,初糖质量浓度60 g/L,(NH4)2SO4 2g/L,CaCO3 10 g/L,温度30℃,pH 5.5～7.0,接种量6％(体积分数),在5L发酵罐中发酵培养96 h,总溶剂产量为16.17 g/L,其中丁醇质量浓度为10.07 g/L,总溶剂产率为30.2％,糖利用率为89.3％.     

以玉米秸秆为原料同步糖化发酵生产燃料乙醇

以玉米秸秆为原料,经酸法预处理后,采用同步糖化发酵SSF工艺生产燃料乙醇。正交试验获得的最佳体系为:培养温度34℃、发酵pH值5.5、发酵的液固比8:1、当发酵108h后,乙醇浓度可达8.33g/L。该实验为纤维质燃料乙醇的产业化生产提供技术依据。     

亚硫酸盐甘蔗渣浆酶解液发酵制备乙醇

以亚硫酸盐甘蔗渣浆酶解液作为原料,利用C. shehatae发酵制取燃料乙醇。结果表明：还原糖最适初始质量浓度为葡萄糖140 g/L、木糖60 g/L、酶解液总糖80 g/L。利用初始葡萄糖55.06 g/L、木糖11.18 g/L、纤维二糖4.51 g/L的亚硫酸盐甘蔗渣浆酶解液发酵,经18 h获得乙醇22.98 g/L。乙醇得率为67.23%,葡萄糖利用率为99.27%,木糖利用率为32.96%,C. shehatae适合作为蔗渣为原料的乙醇发酵菌株。     

Production of fructose and ethanol from sugar beet molasses using Saccharomyces cerevisiae ATCC 36858

The production of enriched fructose syrups and ethanol from beet molasses using Saccharomyces cerevisiae ATCC 36858 was studied. In batch experiments with a total sugar concentration between 94.9 and 312.4 g/L, the fructose yield was above 93% of the theoretical value. The ethanol yield and volumetric productivity in the beet molasses media with sugar concentration below 276.2 g/L were in the range of 59-76% of theoretical value and between 0.48 and 2.97 g of ethanol/(L x h), respectively. The fructose fraction in the carbohydrates content of the produced syrups was more than 95% when the total initial sugar concentration in the medium was below 242.0 g/L. Some oligosaccharides and glycerol were also produced in all tested media. Raffinose and the produced oligosaccharides were completely consumed by the end of the fermentation process when the total initial sugar concentration was below 190.1 g/L. The glycerol concentration was below 16.1 g/L. The results could be useful for a potential industrial production of ethanol and high-fructose syrup from sugar beet molasses.     

Ethanolic fermentation of hydrolysates from ammonia fiber expansion (AFEX) treated corn stover and distillers grain without detoxification and external nutrient supplementation

External nutrient supplementation and detoxification of hydrolysate significantly increase the production cost of cellulosic ethanol. In this study, we investigated the feasibility of fermenting cellulosic hydrolysates without washing, detoxification or external nutrient supplementation using ethanologens Escherichia coli KO11 and the adapted strain ML01 at low initial cell density (16 mg dry weight/L). The cellulosic hydrolysates were derived from enzymatically digested ammonia fiber expansion (AFEX)-treated corn stover and dry distiller's grain and solubles (DDGS) at high solids loading (18% by weight). The adaptation was achieved through selective evolution of KO11 on hydrolysate from AFEX-treated corn stover. All cellulosic hydrolysates tested (36-52 g/L glucose) were fermentable. Regardless of strains, metabolic ethanol yields were near the theoretical limit (0.51 g ethanol/g consumed sugar). Volumetric ethanol productivity of 1.2 g/h/L was achieved in fermentation on DDGS hydrolysate and DDGS improved the fermentability of hydrolysate from corn stover. However, enzymatic hydrolysis and xylose utilization during fermentation were the bottlenecks for ethanol production from corn stover at these experimental conditions. In conclusion, fermentation under the baseline conditions was feasible. Utilization of nutrient-rich feedstocks such as DDGS in fermentation can replace expensive media supplementation.     

Potential utilization of sorghum field waste for fuel ethanol production employing Pachysolen tannophilus and Saccharomyces cerevisiae

In this study, we demonstrate that the sorghum field waste, sorghum stover could be used to produce fuel grade ethanol. The alkaline treatment of 2% NaOH for 8h removed 64% of lignin from sorghum stover. Maximum of 68 and 56 g/L of ethanol yield were obtained by Saccharomyces cerevisiae (MTCC 173) and Pachysolen tannophilus (MTCC 1077) from sorghum stover under optimized condition, respectively. pH and temperature were optimized for the better growth of S. cerevisiae and P. tannophilus. A total of 51% and 48% more ethanol yield was obtained at initial sugar concentration of 200 g/L than 150 g/L by P. tannophilus and S. cerevisiae, respectively. Respiratory deficiency and ethanol tolerance of the organisms were studied. This investigation showed that sorghum field waste could be effectively used for the production of fuel ethanol to avoid conflicts between human food use and industrial use of crops.     

Effect of soy skim from soybean aqueous processing on the performance of corn ethanol fermentation

The feasibility of using soy skim, a co-product of the aqueous processing of soybeans, in ethanol production from corn was evaluated. Specific growth rates were compared when Saccharomyces cerevisiae was grown in soy skim and peptone-yeast extract media supplemented with glucose. Such soy skim was proved to be a good nitrogen source for yeast growth. Next, fermentation of dry-ground corn to ethanol using soy skim as the media was simulated on 1.5-L scale. Replacing water with soy skim increased the initial ethanol production rates by 4-32% while final ethanol yield was about 39 g/100 g dry corn, similar to the result when water was used. Solid and protein contents in the finished beer increased with the addition of soy skim. Thus, replacing water in corn-ethanol fermentation with soy skim is feasible, and may improve the economics of both aqueous soybean processing and corn ethanol fermentation.     

Evaluation of Saccharomyces cerevisiae Y5 for ethanol production from enzymatic hydrolysate of non-detoxified steam-exploded corn stover

Saccharomyces cerevisiae Y5 was used to produce ethanol from enzymatic hydrolysate of non-detoxified steam-exploded corn stover, with and without a nitrogen source, and decreasing inoculum size. The results indicated that the ethanol concentration of 44.55 g/L, corresponding to 94.5% of the theoretical yield was obtained after 24 h, with an inoculum size of 10% (v/v) and nitrogen source (corn steep liquor, CSL) of 40 mL/L. With the same inoculum size, and without CSL, the ethanol concentration was 43.21 g/L, corresponding to 91.7% of the theoretical value after 60 h. With a decreased inoculum size of 5% (v/v), and without CSL, the ethanol concentration was 40.00 g/L, corresponding to 85.8% of the theoretical value after 72 h. The strain offers the potential to improve the economy of cellulosic ethanol production by simplifying the production process and reducing the costs associated with the process such as water, capital equipment and nutrient supplementation.