Statistical optimization of the medium composition by response surface methodology to enhance schizophyllan production by Schizophyllum commune

The response surface methodology (RSM) involving central composite design (CCD) was employed to optimize the fermentation medium for the cell growth and schizophllan production by Schizophyllum commune CGMCC 5.113 in submerged culture at pH 6.5 and 26 degrees C. The four variables involved in this study were glucose, yeast extract, ammonium nitrate, and magnesium sulfate. The statistical analysis of the results showed that, in the range studied, glucose and yeast extract had a highly significant effect on schizophyllan production. The optimal medium for schizophyllan production calculated from the regression model of RSM was as follows: glucose, 18 g/l; yeast extract, 0.5 g/l; NH4NO3, 0.48 g/l; and MgSO4, 0.05 g/l, with a predicted maximum schizophyllan production of 11.74 g/l. These predicted values were experimentally validated. The excellent correlation between predicted and measured values justifies the validity of the response model. The results of bioreactor fermentation also show that the optimized medium enhanced schizophyllan production (12.80 g/l) by S. commune in a 5-1 fermenter.     

The utilization of beet molasses as a novel carbon source for cephalosporin C production by Acremonium chrysogenum: Optimization of process parameters through statistical experimental designs

In this work, cephalosporin C (CPC) production on pilot scale fermenters of 600l capacity with 350l working volume by Acremonium chrysogenum EMCC 904 was performed. The effects of fermentation medium composition, inoculum concentration, initial pH and aeration rate on CPC production by A. chrysogenum strain was investigated by using response surface methodology (RSM). The Plackett-Burman design which involves two concentrations of each nutrient was effective in searching for the major medium components promoting CPC production. Under our experimental conditions; Soya oil, beet molasses and corn steep liquor were found to be the major factors contributing to the antibiotic production. Subsequently, a Box-Behnken design was used for outlining the concentration of the most effective medium constituents. Estimated optimum composition for the production of CPC was as follows: soya oil, 40g/l; beet molasses, 180g/l; and corn steep liquor, 330g/l. The central composite design was used for outlining the optimum values of the fermentation parameters. Estimated optimum values for the production of CPC are as follows: inoculum level, 10(5.5)spores/ml; initial pH, 4.3; and aeration rate, 9364ml/min.     

Optimization of submerged culture requirements for the production of mycelial growth and exopolysaccharide by Cordyceps jiangxiensis JXPJ 0109

AIMS: The objective of the present study was to investigate the optimal culture requirements for mycelial growth and exopolysaccharide production by Cordyceps jiangxiensis JXPJ 0109 in submerged culture. METHODS AND RESULTS: The effects of medium ingredients (i.e. carbon and nitrogen sources, and growth factor) and other culture requirements (i.e. initial pH, temperature, etc.) on the production of mycelia and exopolysaccharide were observed using a one-factor-at-a-time method. More suitable culture requirements for mycelial growth and exopolysaccharide production were proved to be maltose, glycerol, tryptone, soya bean steep powder, yeast extract, medium capacity 200 ml in a 500-ml flask, agitation rate 180 rev min(-1), seed age 4-8 days, inoculum size 2.5-7.5% (v/v), etc. The optimal temperatures and initial pHs for mycelial growth and exopolysaccharide production were at 26 degrees C and pH 5 and at 28 degrees C and pH 7, respectively, and corresponding optimal culture age were observed to be 8 and 10 days respectively. According to the primary results of the one-factor-at-a-time experiments, the optimal medium for the mycelial growth and exopolysaccharide production were obtained using an orthogonal layout method to optimize further. Herein the effects of medium ingredients on the mycelial growth of C. jiangxiensis JXPJ 0109 were in the order of yeast extract > tryptone > maltose > CaCl2 > glycerol > MgSO4 > KH2PO4 and the optimal concentration of each composition was 15 g maltose (food-grade), 10 g glycerol, 10 g tryptone, 10 g yeast extract, 1 g KH2PO4, 0.2 g MgSO4, and 0.5 g CaCl2 in 1 l of distilled water, while the order of effects of those components on exopolysaccharide production was yeast extract > maltose > tryptone > glycerol > KH2PO4 > CaCl2 > MgSO4, corresponding to the optimal concentration of medium was as follows: 20 g maltose (food-grade), 8 g glycerol, 5 g tryptone, 10 g yeast extract, 1 g KH2PO4, and 0.5 g CaCl2 in 1 l of distilled water. CONCLUSIONS: Under the optimal culture requirements, the maximum exopolysaccharide production reached 3.5 g l(-1) after 10 days of fermentation, while the maximum production of mycelial growth achieved 14.5 g l(-1) after 8 days of fermentation. SIGNIFICANCE AND IMPACT OF THE STUDY: This is the first report on the submerged culture requirements for mycelial growth and exopolysaccharide in C. jiangxiensis, and this two-step optimization strategy in this study can be widely applied to other microbial fermentation processes.     

韩芝液体深层发酵培养基的优化研究

固体培养基上比较了韩芝与树舌的菌丝生长速度,二者平均分别达到0.77 cm.d-1和0.67 cm.d-1;液体培养试验了不同碳氮比、培养基组成对韩芝菌丝生长的影响,得出了菌丝生长较适宜的碳氮比范围在18~24∶1,最适宜的碳氮比在22∶1;对比试验、正交试验得出韩芝液体培养最佳的培养基配方为(g.L-1):葡萄糖10.0、玉米粉20.0、大豆粉20.0、酵母粉5.0;在此条件下,菌丝的平均产量可达23.12 g.L-1。     

Solid-state fermentation for gluconic acid production from sugarcane molasses by Aspergillus niger ARNU-4 employing tea waste as the novel solid support

Solid-state fermentation (SSF) was evaluated to produce gluconic acid by metal resistant Aspergillus niger (ARNU-4) strain using tea waste as solid support and with molasses based fermentation medium. Various crucial parameters such as moisture content, temperature, aeration and inoculum size were derived; 70% moisture level, 30 degrees C temperature, 3% inoculum size and an aeration volume of 2.5l min(-1) was suited for maximal (76.3 gl(-1)) gluconic acid production. Non-clarified molasses based fermentation media was utilized by strain ARNU-4 and maximum gluconic acid production was observed following 8-12 days of fermentation cycle. Different concentrations of additives viz. oil cake, soya oil, jaggary, yeast extract, cheese whey and mustard oil were supplemented for further enhancement of the production ability of microorganism. Addition of yeast extract (0.5%) was observed inducive for enhanced (82.2 gl(-1)) gluconic acid production.     

Improvement of very high gravity ethanol fermentation by media supplementation using Saccharomyces cerevisiae

The final ethanol concentration achieved was increased by 17% (to 103 g ethanol/l) when excess assimilable nitrogen was added to the batch very high gravity (VHG) ethanolic fermentations by Saccharomyces cerevisiae. The supplementation of the media with 12 g yeast extract l–1, 0.3 g cell walls l–1, 3 g glycine l–1 and 20 g soya flour l–1 led to halving reduction of the fermentation time to 28 h. The ethanol productivity was enhanced by more than 50% (to achieved value 3.3 g l–1 h–1).     

Elimination of ethanol inhibition by perstraction

Perstraction (membrane-aided solvent extraction) was utilized for elimination of ethanol inhibition in continuous ethanol fermentation using high sugar concentrate. Hollow fibers for an artificial kidney were used as a permeable membrane, and their capacity to extract ethanol was examined by using several organic solvents. When tri-n-butylphosphate was used as an extractant, a 500 g/L feed glucose medium was successfully fermented by immobilized yeast cells. During this continuous fermentation a high ehtanol productivity of 48 g/h-L-gel was held, and the solvent requirement per consumed glucose was 6 L-solvent/kg-glucose.     

Ethanol fermentation of acid-hydrolyzed cellulosic pyrolysate with Saccharomyces cerevisiae

Acid-hydrolysis of cellulosic pyrolysate to glucose and its fermentation to ethanol were investigated. The maximum glucose yield (17.4%) was obtained by the hydrolysis with 0.2 mol/l sulfuric acid using autoclaving at 121 degrees C for 20 min. The fermentation by Saccharomyces cerevisiae of a hydrolysate medium containing 31.6 g/l glucose gave 14.2 g/l ethanol after 24 h, whereas the fermentation of the medium containing 31.6 g/l pure glucose gave 13.7 g/l ethanol after 18 h. The results showed that acid-hydrolyzed pyrolysate could be used for ethanol production. Different nitrogen sources were evaluated and the best ethanol concentration (15.1 g/l) was achieved by single urea. S. cerevisiae (R) was obtained by adaptation of S. cerevisiae to the hydrolysate medium for 12 times, and 40.2 g/l ethanol was produced by it in the fermentation with the hydrolysate medium containing 95.8 g/l glucose, which was about 47% increase in ethanol production compared to its parent strain.     

Influence of Zn2+ and Fe3+ on polysaccharide production and mycelium/yeast dimorphism of Aureobasidium pullulans in batch cultivations

Cultivation of Aureobasidium pullulans in medium with a low concentration of yeast extract (0.4 g/l) led to a decrease in the growth rate early in the fermentation as compared to cultivations in medium with high concentration of yeast extract. When this medium was supplemented with zinc and iron the cultivation closely resembled that obtained in medium with high concentration of yeast extract (4.0 g/l). The culture retained a high growth rate throughout the fermentation and the initiation of the mycelial to yeast (M-Y) transition and the exopolysaccharide production was delayed. In a defined medium or in defined medium without iron only a little exopolysaccharide was produced and the yeast fraction of the total biomass at the onset of the stationary phase was 22%–25%. However, cultivation in the defined medium without zinc resulted in a high production of exopolysaccharide and an increased intensity of the M-Y transition, which led to a yeast fraction of 41%.     

Continuous alpha-amylase production using Bacillus amyloliquefaciens adsorbed on an ion exchange resin

Summary A method for the continuous production of extracellular alpha amylase by surface immobilized cells of Bacillus amyloliquefaciens NRC 2147 has been developed. A large-pore, macroreticular anionic exchange resin was capable of initially immobilizing an effective cell concentration of 17.5 g DW/1 (based on a total reactor volume of 160 ml). The reactor was operated continuously with a nutrient medium containing 15 g/l soluble starch, as well as yeast extract and salts. Aeration was achieved by sparging oxygen enriched air into the column inlet. Fermentor plugging by cells was avoided by periodically substituting the nutrient medium with medium lacking in both soluble starch and yeast extract. This fermentor was operated for over 200 h and obtained a steady state enzyme concentration of 18700 amylase activity units per litre (18.7 kU/l), and an enzyme volumetric productivity of 9700 amylase activity units per litre per hour (9.7 kU/l-h). Parallel fermentations were performed using a 2 l stirred vessel fermentor capable of operation in batch and continuous mode. All fermentation conditions employed were identical to those of the immobilized cell experiments in order to assess the performance of the immobilized cell reactor. Batch stirred tank operation yielded a maximum amylase activity of 150 kU/l and a volumetric productivity of 2.45 kU/l-h. The maximum cell concentration obtained was 5.85 g DW/l. Continuous stirred tank fermentation obtained a maximum effluent amylase activity of 6.9 kU/l and a maximum enzyme volumetric productivity of 2.73 kU/l-h. Both of these maximum values were observed at a dilution rate of 0.345 l/h. The immobilized cell reactor was observed to achieve larger volumetric productivities than either mode of stirred tank fermentation, but achieved an enzyme activity concentration lower than that of the batch stirred tank fermentor.     

Ethanol fermentation of acid-hydrolyzed cellulosic pyrolysate with Saccharomyces cerevisiae

The acid hydrolysis of cellulosic pyrolysate to glucose and its fermentation to ethanol were investigated. The maximum glucose yield (17.4%) was obtained by the hydrolysis with 0.2 mol sulfuric acid per liter pyrolysate using autoclaving at 121 degrees C for 20 min. The fermentation by Saccharomyces cerevisiae of a hydrolysate medium containing 31.6 g/l glucose gave 14.2 g/l ethanol in 24 h, whereas the fermentation of the medium containing 31.6 g/l pure glucose gave 13.7 g/l ethanol in 18 h. The results showed that the acid-hydrolyzed pyrolysate could be used for ethanol production. Different nitrogen sources were evaluated and the best ethanol concentration (15.1 g/l) was achieved by single urea. S. cerevisiae (R) was obtained by adaptation of S. cerevisiae to the hydrolysate medium for 12 times, and 40.2 g/l ethanol was produced by S. cerevisiae (R) in the fermentation with the hydrolysate medium containing 95.8 g/l glucose, which was about 47% increase in ethanol production compared to its parent strain.     

Fermentation of sugar cane bagasse hemicellulosic hydrolysate and sugar mixtures to ethanol by recombinant Escherichia coli KO11

Escherichia coli KO11, carrying the ethanol pathway genes pdc (pyruvate decarboxylase) and adh (alcohol dehydrogenase) from Zymomonas mobilis integrated into its chromosome, has the ability to metabolize pentoses and hexoses to ethanol, both in synthetic medium and in hemicellulosic hydrolysates. In the fermentation of sugar mixtures simulating hemicellulose hydrolysate sugar composition (10.0 g of glucose/l and 40.0 g of xylose/l) and supplemented with tryptone and yeast extract, recombinant bacteria produced 24.58 g of ethanol/l, equivalent to 96.4% of the maximum theoretical yield. Corn steep powder (CSP), a byproduct of the corn starch-processing industry, was used to replace tryptone and yeast extract. At a concentration of 12.5 g/l, it was able to support the fermentation of glucose (80.0 g/l) to ethanol, with both ethanol yield and volumetric productivity comparable to those obtained with fermentation media containing tryptone and yeast extract. Hemicellulose hydrolysate of sugar cane bagasse supplemented with tryptone and yeast extract was also readily fermented to ethanol within 48 h, and ethanol yield achieved 91.5% of the theoretical maximum conversion efficiency. However, fermentation of bagasse hydrolysate supplemented with 12.5 g of CSP/l took twice as long to complete. This revised version was published online in November 2006 with corrections to the Cover Date.     

Contributo Alla Flora Dell'alto Adige

In order to obtain a high ethanol yield from the Jerusalem artichoke raw extract and reduce the fermentation cost, we have engineered a new recombinant Saccharomyces cerevisiae strain that could produce ex-inulinase. The response surface methodology based on Plackett–Burman and Box–Behnken design was used to optimize the medium for the ethanol production from the Jerusalem artichoke raw extracts by the recombinant strain. In the first optimization step, Plackett–Burman design was employed to select significant factors, including concentrations of yeast extract, inoculum, and MgSO₄·7H₂O. In the second step, the steepest ascent experiment was carried out to determine the center point with the three significant factors; the selected combinations were further optimized using the Box–Behnken design. The maximum ethanol production rate was predicted at 91.1 g/l, which was based on a medium consisting of yeast extract 9.24 g/l, inoculum 39.8 ml/l, and MgSO₄·7H₂O 0.45 g/l. In the validating experiment, the ethanol fermentation rate reached 102.1 g/l, closely matching the predicted rate.     

Characterization of ethanol fermentation waste and its application to lactic acid production by Lactobacillus paracasei

In this study, an ethanol fermentation waste (EFW) was characterized for use as an alternative to yeast extract for bulk fermentation processes. EFW generated from a commercial plant in which ethanol is produced from cassava/rice/wheat/barley starch mixtures using Saccharomyces cerevisiae was used for lactic acid production by Lactobacillus paracasei. The effects of temperature, pH, and duration on the autolysis of an ethanol fermentation broth (EFB) were also investigated. The distilled EFW (DEFW) contained significant amounts of soluble proteins (2.91 g/l), nitrogen (0.47 g/l), and amino acids (24.1 mg/l). The autolysis of the EFB under optimum conditions released twice as much amino acids than in the DEFW. Batch fermentation in the DEFW increased the final lactic acid concentration, overall lactic acid productivity, and lactic acid yield on glucose by 17, 41, and 14 %, respectively, in comparison with those from comparable fermentation in a lactobacillus growth medium (LGM) that contained 2 g/l yeast extract. Furthermore, the overall lactic acid productivity in the autolyzed then distilled EFW (ADEFW) was 80 and 27 % higher than in the LGM and DEFW, respectively.     

红酵母NZ-01发酵条件的优化

以红酵母菌株NZ-01为试验菌株,研究其发酵工艺与中试生产。采用摇瓶发酵优化的方式,研究培养基组分与发酵工艺条件对该菌发酵的影响,并进行中试放大生产。结果显示,该菌最适生长培养基组分为葡萄糖10g/L,蔗糖10g/L,酵母膏10g/L,牛肉膏2.5g/L;色素合成最适培养基组分为葡萄糖15g/L,蔗糖10g/L,酵母膏2.5g/L,牛肉膏5g/L。最适生长起始pH值为6.0,最适接种量为8%,生长周期为44h;最适色素合成起始pH值为7.0,最适色素合成接种量为8%,色素合成周期为48h。发酵优化后的色素产量3.88μg/mL较优化前1.71μg/mL提高了127%。中试产量达3.05μg/mL。红酵母菌NZ-01优化后的发酵条件可以应用于中试生产虾青素,有规模化生产应用潜力。     

Optimization of medium composition for actinorhodin production by Streptomyces coelicolor A3(2) with response surface methodology

Optimization of the fermentation medium for maximization of actinorhodin production by Streptomyces coelicolor A3(2) was carried out. Response surface methodology (RSM) was applied to optimize the medium constituents. A 2⁴ full-factorial central composite design (CCD) was chosen to explain the combined effects of the four medium constituents, viz. sucrose, glucose, yeast extract (YE) and peptone, and to design a minimum number of experiments. The P-values of the coefficients for linear, quadratic and cross-product effect of sucrose and glucose concentration were <0.0001, suggesting that these were critical variables having the greatest effect on the production of actinorhodin in the complex medium. The optimized medium consisting of 339 g/l sucrose, 1 g/l glucose, 1.95 g/l YE and 2.72 g/l peptone predicted 195 mg/l of actinorhodin which was 32% higher than that of the unoptimized medium. The amounts of glucose, YE and peptone required were also reduced with RSM.     

Production of tyrosinase by Auricularia auricula using low cost fermentation medium

Low cost fermentation media using agricultural by-products (wheat bran extract, rice bran extract and soybean meal extract) as a major nutrient source, were evaluated for the production of tyrosinase from the fungus Auricularia auricula in submerged culture. In single-factor experiments, three components (wheat bran extract, casein and CuSO₄) were chosen to further optimize medium composition using response surface methodology (RSM). The central composite experimental results showed the following optimum medium composition: wheat bran extract 36.0 %, casein 1.1 g/l and CuSO₄ 0.13 g/l. Under these conditions, the highest tyrosinase activity was 17.22 U/ml, which was 2.1 fold higher than that obtained using the non-optimized medium. The present study is the first to report the statistical optimization of medium composition for production of tyrosinase by A. auricula using cheaper wheat bran extract as a major nutrient source. These results might provide a reference for the development of a cost-effective medium for commercial production of tyrosinase.     

Optimization of fermentation conditions for production of anti-TMV extracellular ribonuclease by Bacillus cereus using response surface methodology

Bacillus cereus ZH14 was previously found to produce a new type of antiviral ribonuclease, which was secreted into medium and active against tobacco mosaic virus. In order to enhance the ribonuclease production, in this study the optimization of culture conditions using response surface methodology was done. The fermentation variables including culture temperature, initial pH, inoculum size, sucrose, yeast extract, MgSO₄·7H₂O, and KNO₃ were considered for selection of significant ones by using the Plackett–Burman design, and four significant variables (sucrose, yeast extract, MgSO₄·7H₂O, and KNO₃) were further optimized by a 2⁴ factorial central composite design. The optimal combination of the medium constituents for maximum ribonuclease production was determined as 8.50 g/l sucrose, 9.30 g/l yeast extract, 2.00 g/l MgSO₄·7H₂O, and 0.62 g/l KNO₃. The enzyme activity was increased by 60%. This study will be helpful to the future commercial development of the new bacteria-based antiviral ribonuclease fermentation process.     

Influence of Medium Composition on Xylitol Bioproduction from Wheat Straw Hemicellulosic Hydrolysate

Summary Xylose-to-xylitol batch bioconversions from wheat straw hemicellulosic hydrolysate were carried out in Erlenmeyer flasks in order to assess the influence of medium composition (hydrolysate concentration, supplementation with ammonium sulphate, calcium chloride and rice bran extract, and initial pH) on xylitol production, productivity and yield. By using the screening design and the response surface methodologies, the statistically significant variables influencing the bioconversion were selected and linear models were fitted to the experimental data. According to the results, the best conditions to perform the bioconversion consisted in using a threefold concentrated hydrolysate supplemented with ammonium sulphate (1.0 g/l) and rice bran extract (5.0 g/l), whose pH was adjusted to 6.0 prior to inoculation. Under these conditions, a xylitol production of 24.17 g/l was observed after 72 h of fermentation, resulting in a productivity of 0.34 g/l h and in a bioconversion yield of 0.49 g/g.     

Culture conditions for growth and solvent biosynthesis by a modified Clostridium acetobutylicum

Summary A modified strain of Clostridium acetobutylicum and the fermentation medium conditions for good growth of the culture and normal production of solvents are described. The pretreatment of the culture with butyric-acid-enriched medium increased the final solvent yield on sugar and lowered the residual butyric acid accumulation. In a complex medium, relatively high concentrations of yeast extract (7.5 g/l) and ammonium sulphate (3 g/l to 6 g/l) were required for normal solvent synthesis. The nitrogen requirements for cellular growth and solvent production were distinctively different. Production of solvents and growth of the culture were dependent on the concentration of para-aminobenzoic acid and relatively independent of the variations of the initial pH of the medium in the range of 4.6 to 6.3. Solvent production was obtained with initial glucose concentrations of 20.5 g/l to 70 g/l, resulting in a maximum solvent concentration of 22 g/l and a maximum yield on glucose of 32.7%.