Kinetic behaviors between acetone and composite bead in biofilter

In this study, the kinetic behaviors between acetone and composite bead were investigated. The microbial growth rate decreased with increasing average inlet concentration and increased with increasing operation temperature at average inlet concentration ranging from 50 to 300 ppm and operation temperature ranging from 30 to 40°C. The microbial growth rate would be inhibited with increasing average inlet concentration, and the inhibitive effect was more pronounced at higher operation temperature. The microbial growth rate would be enhanced with increasing operation temperature, and the enhancing effect was more pronounced at higher average inlet concentration. The values of maximum reaction rate V _m and half-saturation constant K _s ranged from 0.04 to 0.05 g-C/h-kg packing material and from 37.19 to 42.77 ppm, respectively. The biochemical reaction model could be regarded as the zero-order kinetic with the diffusion rate limitation. The biochemical reaction rate decreased with increasing average inlet concentration and increased with increasing operation temperature. The biochemical reaction rate would be inhibited with increasing average inlet concentration, and the inhibitive effect was more pronounced at lower operation temperature. The biochemical reaction rate would be enhanced with increasing the operation temperature, and the enhancing effect was more pronounced at higher average inlet concentration. The maximum elimination capacity of biofilter increased with increasing operation temperature. The values of critical and maximum elimination capacity ranged from 0.07 to 0.15 and from 0.13 to 0.16 g-C/h-kg packing material, respectively.     

Kinetic comparisons of mesophilic and thermophilic aerobic biomass

Kinetic parameters describing growth and decay of mesophilic (30°C) and thermophilic (55°C) aerobic biomass were determined in continuous and batch experiments by using oxygen uptake rate measurements. Biomass was cultivated on a single soluble substrate (acetate) in a mineral medium. The intrinsic maximum growth rate (μ _max) at 55°C was 0.71±0.09 h⁻¹, which is 1.5 times higher than the μ _max at 30°C (0.48±0.11 h⁻¹). The biomass decay rates increased from 0.004 h⁻¹ at 30°C to 0.017 h⁻¹ at 55°C. Monod constants were very low for both types of biomass: 9±2 mg chemical oxygen demand (COD) l⁻¹at 30°C and 3±2 mg COD l⁻¹at 55°C. Theoretical biomass yields were similar at 30 and 55°C: 0.5 g biomass COD (g acetate COD)⁻¹. The observed biomass yields decreased under both temperature conditions as a function of the cell residence time. Under thermophilic conditions, this effect was more pronounced due to the higher decay rates, resulting in lower biomass production at 55°C compared to 30°C. Electronic Publication     

Effect of temperature on cell growth and production of transparent exopolymer particles by the diatom Coscinodiscus granii isolated from marine mucilage

In the autumn of 2007, marine mucilage caused by the diatom Coscinodiscus granii occurred in the central area of Ariake Sound, Japan, and resulted in damage to fishery. To elucidate the mechanism underlying the outbreak of marine mucilage, we examined the effect of temperature on cell growth and production of transparent exopolymer particles (TEPs) in a culture of this species. Growth and TEP production of C. granii are influenced by temperature. The maximum growth rate (1.63 divisions day⁻¹) and cell yield (1,280 cells mL⁻¹) at all temperatures were obtained at 30°C. Optimal growth rates (>1.15 divisions day⁻¹: ca. 70% of maximum) and cell yield (>900 cells mL⁻¹: ca. 70% of maximum) were observed at temperatures of 25–30°C. TEP production by C. granii depended on whether volume- or cell-related values were considered. The maximum volume-normalized increase rates and concentrations of TEP at all temperatures were observed at 25°C. However, when production rates and concentrations of TEP were normalized to cell numbers, optimal values were measured at 10–15°C. In Ariake Sound, when marine mucilage caused by C. granii occurred, the temperature ranged from 25.0 to 25.4°C. This suggests that growth conditions of C. granii are important factors for production of marine mucilage.     

Optimization of flow rate,initial metal ion concentration and biomass density for maximum removal of Cu2+ by immobilized Microcystis

The potential of alginate-immobilized Microcystis packed in a column for maximum removal of Cu²⁺ at different flow rates, biomass, and initial metal ion concentration was assessed in a continuous flow system. Although Cu²⁺ removal did occur at all the flow rates tested, it was maximum (54%) at 0.75-ml min⁻¹ flow rate, 30 μg ml⁻¹ initial metal ion concentration and 0.016 g biomass. Cu²⁺ removal was influenced by inlet metal ion concentration and biomass density. An increase in the biomass concentration from 0.016 to 0.128 g resulted in an apparent increase in percentage removal but the Cu²⁺ adsorbed per unit dry wt. declined. When the flow rate (0.75 ml min⁻¹) and biomass density (0.064 g) were kept constant and the inlet metal ion concentration was varied from 10 to 150 μg ml⁻¹, a 68% removal of Cu²⁺ was obtained at 50 μg ml⁻¹ initial concentration in a time duration of 15 min. The metal-laden columns were efficiently desorbed and regenerated following elution with double distilled water (DDW) (pH 2) (89%). This was followed by 1 mm EDTA > 1 mm NTA > 0.1 mm EDTA > 1 mm HCl > 1 mm HNO₃ > 5 mm CaCl₂ > DDW (pH 7.0) > 1 mm NaHCO₃ > 1 mm CaCl₂. Of the total (2.83 mg) adsorbed Cu²⁺, 1.89 mg (67%) was desorbed by DDW (pH 2) within the first 20 min of elution time. Thereafter the desorption rate slowed down and only 22% (0.632 mg) desorption was obtained in the last 20 min. In contrast to water pH 2, the desorption of Cu²⁺ by 1 mm EDTA was very slow, the maximum being 8% after 40 min of elution. This revised version was published online in July 2006 with corrections to the Cover Date.     

Photosynthetic characteristics and physiological plasticity of an Aphanizomenon flos-aquae (Cyanobacteria, Nostocaceae) winter bloom in a deep oligo-mesotrophic lake (Lake Stechlin, Germany)

In winter of 2009/2010, Aphanizomenon flos-aquae bloomed in the ice and snow covered oligo-mesotrophic Lake Stechlin, Germany. The photosynthesis of the natural population was measured at eight temperatures in the range of 2–35°C, at nine different irradiance levels in the range of 0–1,320 μmol m⁻² s⁻¹ PAR at each applied temperature. The photoadaptation parameter (I _k) and the maximum photosynthetic rate (P _max) correlated positively with the temperature between 2 and 30°C, and there was a remarkable drop in both parameters at 35°C. The low I _k at low temperatures enabled the active photosynthesis of overwintering populations at low irradiance levels under ice and snow cover. The optimum of the photosynthesis was above 20°C at irradiances above 150 μmol m⁻² s⁻¹. At lower irradiance levels (7.5–30 μmol m⁻² s⁻¹), the photosynthesis was the most intensive in the temperature range of 2–5°C. The interaction between light and temperature allowed the proliferation of A. flos-aquae in Lake Stechlin resulting in winter water bloom in this oligo-mesotrophic lake. The applied 2°C is the lowest experimental temperature ever in the photosynthesis/growth studies of A. flos-aquae, and the results of the P–I and P–T measurements provide novel information about the tolerance and physiological plasticity of this species.     

Temperature and irradiance impacts on the growth,pigmentation and photosystem II quantum yields of <Emphasis Type="Italic">Haematococcus pluvialis</Emphasis> (Chlorophyceae)

The microalga Haematococcus pluvialis Flotow has been the subject of a number of studies concerned with maximizing astaxanthin production for use in animal feeds and for human consumption. Several of these studies have specifically attempted to ascertain the optimal temperature and irradiance combination for growth of H. pluvialis, but there has been a great deal of disagreement between laboratories. “Ideal” levels of temperature and irradiance have been reported to range from 14 to 28°C and 30 to 200 μmol photons m⁻² s⁻¹. The objective of the present study was to simultaneously explore temperature and irradiance effects for a single strain of H. pluvialis (UTEX 2505) across an experimental region that encompassed the reported “optimal” combinations of these factors for multiple strains. To this end, a two-dimensional experimental design based on response surface methodology (RSM) was created. Maximum growth rates for UTEX 2505 were achieved at 27°C and 260 μmol photons m⁻² s⁻¹, while maximum quantum yield for stable charge separation at PSII (F_v/F_m) was achieved at 27°C and 80 μmol photons m⁻² s⁻¹. Maximum pigment concentrations correlated closely with maximum F_v/F_m. Numeric optimization of growth rate and F_v/F_m produced an optimal combination of 27°C and 250 μmol photons m⁻² s⁻¹. Polynomial models of the various response surfaces were validated with multiple points and were found to be very useful for predicting several H. pluvialis UTEX 2505 responses across the entire two-dimensional experimental design space.     

Effect of high temperature on photosynthesis and transpiration of sweet corn (<Emphasis Type="Italic">Zea mays</Emphasis> L. var. <Emphasis Type="Italic">rugosa</Emphasis>)

Four temperature treatments were studied in the climate controlled growth chambers of the Georgia Envirotron: 25/20, 30/25, 35/30, and 40/35 °C during 14/10 h light/dark cycle. For the first growth stage (V3-5), the highest net photosynthetic rate (P _N) of sweet corn was found for the lowest temperature of 28–34 μmol m⁻² s⁻¹ while the P _N for the highest temperature treatment was 50–60 % lower. We detected a gradual decline of about 1 P _N unit per 1 °C increase in temperature. Maximum transpiration rate (E) fluctuated between 0.36 and 0.54 mm h⁻¹ (≈5.0–6.5 mm d⁻¹) for the high temperature treatment and the minimum E fluctuated between 0.25 and 0.36 mm h⁻¹ (≈3.5–5.0 mm d⁻¹) for the low temperature treatment. Cumulative CO₂ fixation of the 40/35 °C treatment was 33.7 g m⁻² d⁻¹ and it increased by about 50 % as temperature declined. The corresponding water use efficiency (WUE) decreased from 14 to 5 g(CO₂) kg⁻¹(H₂O) for the lowest and highest temperature treatments, respectively. Three main factors affected WUE, P _N, and E of Zea: the high temperature which reduced P _N, vapor pressure deficit (VPD) that was directly related to E but did not affect P _N, and quasi stem conductance (QC) that was directly related to P _N but did not affect E. As a result, WUE of the 25/20 °C temperature treatment was almost three times larger than that of 40/35 °C temperature treatment.     

Irreversible changes in barley leaf chlorophyll fluorescence detected by the fluorescence temperature curve in a linear heating/cooling regime

The chlorophyll fluorescence (F) temperature curves in a linear time-temperature heating/cooling regime were used to study heat-induced irreversible F changes in primary green leaves of spring barley (Hordeum vulgare L. cv. Akcent). The leaf segments were heated in a stirred water bath at heating rates of 0.0083, 0.0166, 0.0333, and 0.0500 °C s⁻¹ from room temperature up to maximal temperature T _m and then linearly cooled to 35 °C at the same rate. The F intensity was measured by a pulse-modulated technique. The results support the existence of the two critical temperatures of irreversible F changes postulated earlier, at 45–48 and 53–55 °C. The critical temperatures are slightly dependent on the heating rate. Two types of parameters were used to characterize the irreversibility of the F changes: the coefficient of irreversibility μ defined as the ratio of F intensity at 35 °C at the starting/ending parts of the cycle and the slopes of tangents of linear parts of the F temperature curve. The dependence of μ on T _m revealed a maximum, which moved from 54 to 61 °C with the increasing heating/cooling rate v from 0.0083 to 0.0500 °C s⁻¹, showing two basic phases of the irreversible changes. The Arrhenius and Eyring approaches were applied to calculate the activation energies of the initial increase in μ. The values varied between 30 and 50 kJ mol⁻¹ and decreased slightly with the increasing heating rate.     

An improved nitrilase-mediated bioprocess for synthesis of nicotinic acid from 3-cyanopyridine with hyperinduced <Emphasis Type="Italic">Nocardia globerula</Emphasis> NHB-2

Nitrilase of Nocardia globerula NHB-2 was induced by short-chain aliphatic nitriles (valeronitrile > isobutyronitrile > butyronitrile > propionitrile) and exhibited activity towards aromatic nitriles (benzonitrile > 3-cyanopyridine > 4-cyanopyridine > m-tolunitrile > p-tolunitrile). Hyperinduction of nitrilase (6.67 U mg_DCW⁻¹, 18.7 U mL⁻¹) was achieved in short incubation time (30 h, 30°C) through multiple feeding of isobutyronitrile in the growth medium. The nitrilase of this organism exhibits both substrate and product inhibition effects. In a fed batch reaction at 1 L scale using hyperinduced resting cells corresponding to 10 U mL⁻¹ nitrilase activity (1.5 mg_DCW mL⁻¹), a total of 123.11 g nicotinic acid was produced at a rate of 24 g h⁻¹ g_DCW⁻¹.     

Determination of shelf life of <Emphasis Type="Italic">Spirulina platensis</Emphasis> (MI<Subscript>2</Subscript>) grown in the Philippines

Gamma linolenic acid (GLA) degradation in Spirulina followed first-order reaction kinetics. At an accelerated temperature range of 45 to 55°C, the degradation rate constants (k _r) of GLA obtained were 4.0 × 10⁻² to 8.8 × 10⁻² day⁻¹. The energy of activation (E _a) was 16.53 kcal mol⁻¹, and the Q₁₀ was 2.22. Based on 20% GLA degradation, the shelf life of sun-dried Spirulina at 30°C is 263 days or 8.6 months using the Arrhenius plot, and 258 days or 8.5 months using the Q ₁₀ approach. Presented at the 6th Meeting of the Asia Pacific Society of Applied Phycology, Manila, Philippines.     

Bioethanol production in batch mode by a native strain of <Emphasis Type="Italic">Zymomonas mobilis</Emphasis>

Two wild strains of Zymomonas mobilis were isolated (named as ML1 and ML2) from sugar cane molasses obtained from different farms of Santander, Colombia. Initially, selection of the best ethanol-producer strains was carried out using ethanol production parameters obtained with a commercial strain Z. mobilis DSM 3580. Three isolated strains were cultivated in a culture medium containing yeast extract, peptone, glucose and salts, at pH 6 and 32°C with stirring rate of 65 rpm during 62 h. The best results of ethanol production were obtained with the native strain ML1, reaching a maximum ethanol concentration of 79.78 g l⁻¹. ML1 and ML2 strains were identified as Z. mobilis, according to the morphology, biochemical tests and molecular characterization by PCR of specific DNA sequences from Z. mobilis. Subsequently, the effect of different nitrogen sources on production of ethanol was evaluated. The best results were obtained using urea at a 0.73 g/l. In this case, maximum concentration of ethanol was 83.81 g l⁻¹, with kinetic parameters of yield of ethanol on biomass (Y_P/X) = 69.01(g g⁻¹), maximum volumetric productivity of ethanol (Qp_max) = 2.28 (g l⁻¹ h⁻¹), specific productivity of ethanol (q_P) = 3.54 (h⁻¹) and specific growth rate (μ) = 0.12 h⁻¹. Finally, we studied the effect of different culture conditions (pH, temperature, stirring, C/N ratio) with a Placket-Burman′s experimental design. This optimization indicated that the most significant variables were temperature and stirring. In the best culture conditions a significant increase in all variables of response was achieved, reaching a maximum ethanol concentration of 93.55 g l⁻¹.     

Enzymatic resolution of racemic phenyloxirane by a novel epoxide hydrolase from Aspergillus niger SQ-6 and its fed-batch fermentation

A microorganism with the ability to catalyze the resolution of racemic phenyloxirane was isolated and identified as Aspergillus niger SQ-6. Chiral capillary electrophoresis was successfully applied to separate both phenyloxirane and phenylethanediol. The epoxide hydrolase (EH) involved in this resolution process was (R)-stereospecific and constitutively expressed. When whole cells were used during the biotransformation process, the optimum temperature and pH for stereospecific vicinal diol production were 35°C and 7.0, respectively. After a 24-h conversion, the enantiomer excess of (R)-phenylethanediol produced was found to be >99%, with a conversion rate of 56%. In fed-batch fermentations at 30°C for 44 h, glycerol (20 g L⁻¹) and corn steep liquor (CSL) (30 g L⁻¹) were chosen as the best initial carbon and nitrogen sources, and EH production was markedly improved by pulsed feeding of sucrose (2 g L⁻¹ h⁻¹) and continuous feeding of CSL (1 g L⁻¹ h⁻¹) at a fermentation time of 28 h. After optimization, the maximum dry cell weight achieved was 24.5±0.8 g L⁻¹; maximum EH production was 351.2±13.1 U L⁻¹ with a specific activity of 14.3±0.5 U g⁻¹. Partially purified EH exhibited a temperature optimum at 37°C and pH optimum at 7.5 in 0.1 M phosphate buffer. This study presents the first evidence for the existence of a predicted epoxide racemase, which might be important in the synthesis of epoxide intermediates.     

Effects of temperature on photosynthesis of two morphologically contrasting plant species along an altitudinal gradient in the tropical high Andes

The effects of temperature on photosynthesis of a rosette plant growing at ground level, Acaena cylindrostachya R. et P., and an herb that grows 20–50 cm above ground level, Senecio formosus H.B.K., were studied along an altitudinal gradient in the Venezuelan Andes. These species were chosen in order to determine – in the field and in the laboratory – how differences in leaf temperature, determined by plant form and microenvironmental conditions, affect their photosynthetic capacity. CO₂ assimilation rates (A) for both species decreased with increasing altitude. For Acaena leaves at 2900 m, A reached maximum values above 9 μmol m⁻² s⁻¹, nearly twice as high as maximum A found at 3550 m (5.2) or at 4200 m (3.9). For Senecio leaves, maximum rates of CO₂ uptake were 7.5, 5.8 and 3.6 μmol m⁻² s⁻¹ for plants at 2900, 3550 and 4200 m, respectively. Net photosynthesis-leaf temperature relations showed differences in optimum temperature for photosynthesis (A _o.t.) for both species along the altitudinal gradient. Acaena showed similar A _o.t. for the two lower altitudes, with 19.1°C at 2900 m and 19.6°C at 3550 m, while it increased to 21.7°C at 4200 m. Maximum A for this species at each altitude was similar, between 5.5 and 6.0 μmol m⁻² s⁻¹. For the taller Senecio, A _o.t. was more closely related to air temperatures and decreased from 21.7°C at 2900 m, to 19.7°C at 3550 m and 15.5°C at 4200 m. In this species, maximum A was lower with increasing altitude (from 6.0 at 2900 m to 3.5 μmol m⁻² s⁻¹ at 4200 m). High temperature compensation points for Acaena were similar at the three altitudes, c. 35°C, but varied in Senecio from 37°C at 2900 m, to 39°C at 3550 m and 28°C at 4200 m. Our results show how photosynthetic characteristics change along the altitudinal gradient for two morphologically contrasting species influenced by soil or air temperatures. Received: 5 July 1997 / Accepted: 25 October 1997     

Biofiltration of ketone compounds by a composite bead biofilter

In this study, the biochemical kinetic behaviors of ketone compounds in a composite bead biofilter were investigated. Both microbial growth rate kg and biochemical reaction rate kd would be inhibited at higher average inlet concentration. For the microbial growth process, the inhibitive effect was the least pronounced for acetone and the order of kg value was MEK>MIPK>acetone in the average inlet concentration range of 100-150 ppm. The degree of inhibitive effect was almost the same for three ketone compounds and the order of kg value was acetone>MEK>MIPK in the average inlet concentration range of 200-300 ppm. The values of half-saturation constant Ks for acetone, MEK and MIPK were 26.80, 21.56 and 22.96 ppm, respectively. The values of maximum reaction rate Vm for acetone, MEK and MIPK were 8.55, 9.06 and 7.55 g-C/h-kg packed material, respectively. The zero-order kinetic with the diffusion rate limitation could be regarded as the most adequate biochemical reaction model. For the biochemical reaction process, the inhibitive effect was the most pronounced for MEK and the order of kd value was MEK>acetone>MIPK in the average inlet concentration range of 100-150 ppm. The degree of inhibitive effect was MIPK>MEK>acetone and the order of kd value was acetone>MEK>MIPK in the average inlet concentration range of 200-300 ppm. The maximum elimination capacity of acetone, MEK and MIPK were 0.157, 0.127 and 0.101 g-C/h-kg packed material.     

Variations in daytime net carbon and water exchange in a montane shrubland ecosystem in southeast Spain

Carbon and water fluxes in a semiarid shrubland ecosystem located in the southeast of Spain (province of Almería) were measured continuously over one year using the eddy covariance technique. We examined the influence of environmental variables on daytime (photosynthetically active photons, F _P >10 μmol m⁻² s⁻¹) ecosystem gas exchange and tested the ability of an empirical eco-physiological model based on F _P to estimate carbon fluxes over the whole year. The daytime ecosystem fluxes showed strong seasonality. During two solstitial periods, summer with warm temperatures (>15 °C) and sufficient soil moisture (>10 % vol.) and winter with mild temperatures (>5 °C) and high soil moisture contents (>15 % vol.), the photosynthetic rate was higher than the daytime respiration rate and mean daytime CO₂ fluxes were ca. −1.75 and −0.60 μmol m⁻² s⁻¹, respectively. Daytime evapotranspiration fluxes averaged ca. 2.20 and 0.24 mmol m⁻² s⁻¹, respectively. By contrast, in summer and early autumn with warm daytime temperatures (>10 °C) and dry soil (<10 % vol.), and also in mid-winter with near-freezing daytime temperatures the shrubland behaved as a net carbon source (mean daytime CO₂ release of ca. 0.60 and 0.20 μmol m⁻² s⁻¹, respectively). Furthermore, the comparison of water and carbon fluxes over a week in June 2004 and June 2005 suggests that the timing—rather than amount—of spring rainfall may be crucial in determining growing season water and carbon exchange. Due to strongly limiting environmental variables other than F _P, the model applied here failed to describe daytime carbon exchange only as a function of F _P and could not be used over most of the year to fill gaps in the data.     

Combined effect of temperature and light intensity on growth and extracellular polymeric substance production by the cyanobacterium Arthrospira platensis

The effects of light intensity and temperature on Arthrospira platensis growth and production of extracellular polymeric substances (EPS) in batch culture were evaluated using a three-level, full-factorial design and response surface methodology. Three levels were tested for each parameter (temperature: 30, 35, 40°C; light intensity: 50, 115, 180 μmol photons m⁻² s⁻¹). Both growth and EPS production are influenced mainly by the temperature factor but the interaction term temperature*light intensity also had a significant effect. In addition, conditions optimising EPS production are different from those optimising growth. The highest growth rate (0.414 ± 0.003 day⁻¹) was found at the lowest temperature (30°C) and highest light intensity (180 μmol photons m⁻² s⁻¹) tested, no optima were detectable within the given test range. Obviously, optima for growth must be at a temperature lower than 30°C and a light intensity higher than 180 μmol photons m⁻² s⁻¹. For EPS production, light intensity had a positive linear effect (optimum obviously higher than 180 μmol photons m⁻² s⁻¹), but for the temperature parameter a maximum effect was detectable at 35°C.     

Biodegradation kinetic behaviors of n-butyl alcohol and sec-butyl alcohol in a composite bead biofilter

Biodegradation kinetic behaviors of n-butyl alcohol and sec-butyl alcohol in a composite bead biofilter were investigated. The microbial growth rate of n-butyl alcohol was greater than that of sec-butyl alcohol in the inlet concentration range of 50–300 ppm. The microbial growth rate was inhibited at higher inlet concentration, and the inhibitive effect in the concentration range of 50–150 ppm was more pronounced than that in the concentration range of 150–300 ppm. The degree of inhibitive effect for n-butyl alcohol was more sensitive than that for sec-butyl alcohol in the concentration range of 50–150 ppm. The zero-order kinetic with the diffusion rate limitation could be regarded as the most adequate biochemical reaction model. For the biochemical reaction process, the biochemical reaction rate coefficient of n-butyl alcohol was greater than that of sec-butyl alcohol in the inlet concentration range of 50–300 ppm. The biochemical reaction rate coefficient was decreased with increasing inlet concentration. The inhibitive effect for sec-butyl alcohol was more pronounced than that for n-butyl alcohol. The factor of the chemical structure of compound was more predominant in the microbial growth and biochemical reaction processes. The maximum elimination capacity of n-butyl alcohol and sec-butyl alcohol were 55.7 and 20.9 g C h^?1 m^?3 bed volume, respectively. The primary alcohol was easily biodegraded by the microbial.     

Effect of light and temperature on the cyanobacterium <Emphasis Type="Italic">Arthronema africanum</Emphasis> - a prospective phycobiliprotein-producing strain

The effect of light intensity (50–300 μmol photons m⁻² s⁻¹) and temperature (15–50°C) on chlorophyll a, carotenoid and phycobiliprotein content in Arthronema africanum biomass was studied. Maximum growth rate was measured at 300 μmol photons m⁻² s⁻¹ and 36°C after 96 h of cultivation. The chlorophyll a content increased along with the increase in light intensity and temperature and reached 2.4% of dry weight at 150 μmol photons m⁻² s⁻¹ and 36°C, but it decreased at higher temperatures. The level of carotenoids did not change significantly under temperature changes at illumination of 50 and 100 μmol photons m⁻² s⁻¹. Carotenoids were about 1% of the dry weight at higher light intensities: 150 and 300 μmol photons m⁻² s⁻¹. Arthronema africanum contained C-phycocyanin and allophycocyanin but no phycoerythrin. The total phycobiliprotein content was extremely high, more than 30% of the dry algal biomass, thus the cyanobacterium could be deemed an alternative producer of C-phycocyanin. A highest total of phycobiliproteins was reached at light intensity of 150 μmol photons m⁻² s⁻¹ and temperature of 36°C, C-phycocyanin and allophycocyanin amounting, respectively, to 23% and 12% of the dry algal biomass. Extremely low (<15°C) and high temperatures (>47°C) decreased phycobiliprotein content regardless of light intensity.     

Immobilization of cyclodextrin glucanotransferase on amberlite IRA-900 for biosynthesis of transglycosylated xylitol

Cyclodextrin glucanotransferase (CGTase) fromThermoanaerobacter sp. was adsorbed on the ion exchange resin Amberlite IRA-900. The optimum conditions for the immobilization of the CGTase were pH 6.0 and 600 U CGTase/g resin, and the maximum yield of immobilization was around 63% on the basis of the amount ratio of the adsorbed enzyme to the initial amount in the solution. Immobilization of CGTase shifted the optimum temperature for the enzyme to produce transglycosylated xylitol from 70°C to 90°C and improved the thermal stability of immobilized CGTase, especially after the addition of soluble starch and calcium ions. Transglycosylated xylitol was continuously produced using immobilized CGTase in the column type packed bed reactor, and the operating conditions for maximum yield were 10% (w/v) dextrin (13 of the dextrose equivalent) as the glycosyl donor, 10% (w/v) xylitol as the glycosyl acceptor, 20 mL/h of medium flow rate, and 60°C. The maximum yield of transglycosylated xylitol and productivity were 25% and 7.82 g·L⁻¹·h⁻¹, respectively. The half-life of the immobilized CGTase in a column type packed bed reactor was longer than 30 days.     

Facultative hypothermia as a thermoregulatory strategy in the phyllostomid bats, Carollia perspicillata and Sturnira lilium

The present study questions whether hypothermia is an artifact due to captivity-induced stress or a thermoregulatory strategy for bats of the neotropical family Phyllostomidae. In Guanacaste, Costa Rica, Carollia perspicillata and Sturnira lilium exhibited a bimodal distribution of body temperatures when submitted to an ambient temperature of 21 °C. Body temperature was highly correlated with body mass in both species. C. perspicillata of mass ≥20 g and S. lilium of mass ≥17 g remained normothermic (body temperature >37 °C), whereas at masses below 18 g and 13 g, respectively, >80% of individuals were hypothermic (body temperature ≤32 °C). In two treatment groups for each species, we restricted food intake to ca. 20% of body mass on either night 1 or night 4 following capture. Hypothermia was significantly related to food-restriction, but not time in captivity. Metabolic rate (ml O₂ ·  g⁻¹ h⁻¹) at ambient temperature = 21 °C was MR = e ^{(–2.11 + 0.101 Tb)} (r ² = 0.7, P < 0.001) for C. perspicillata and MR = e ^{(−2.62 + 0.115 Tb)} (r ² = 0.89) for S. lilium. Free-ranging, radio tagged C. perspicillata exhibited daily depression of body temperature to 33–34 °C. We conclude that hypothermia is an thermoregulatory strategy that allows phyllostomid bats to adjust metabolic rate to feeding success and the level of fat stores. Accepted: 20 August 1996