毕赤酵母高密度表达重组猪胰岛素前体的研究

对摇瓶和50L罐上的重组菌毕赤酵母(Pichia pastoris)表达猪胰岛素前体(PIP)的发酵过程进行了研究。摇瓶发酵中,最佳诱导周期为60 h左右,诱导期甲醇的最佳加入量为每日2．0%～2．5%。50L发酵过程分为批发酵、补料和诱导表达3个阶段。生长期(批发酵和补料阶段)细胞干重与培养时间的关系可用模型y= 0．6525e~(0．1909t)来描述。在批发酵阶段和补料阶段,流加的氨水和甘油几乎全部用来合成菌体和维持,没有其他副产物产生。诱导表达阶段流加的氨水和甲醇分别约有80%和70%被菌体利用。将摇瓶与发酵罐的实验结果进行了比较,发现摇瓶发酵的限制因子很可能是溶氧,而罐发酵的限制因子为碳源,因此,将摇瓶实验的结果放大到发酵罐时调整了控制策略,加大了甲醇的补料速率,最终PIP浓度达到1．72g/L。     

枯草芽孢杆菌β-甘露聚糖酶补料发酵及其特性研究

采用正交实验设计对枯草芽孢杆菌产β－甘露聚糖酶的培养基组成和培养条件进行优化,在此基础上进行摇瓶补料发酵,酶活达223．47U／mL,较未补料的酶活提高了32．09％。酶反应最适pH为6．5,最适温度为70℃,该酶在pH5.0-10.0和70摄氏度以下稳定,水解魔芋胶产物主要为二糖以上低聚糖。     

枯草芽孢杆菌β-甘露聚糖酶补料发酵及其特性研究

采用正交实验设计对枯草芽孢杆菌产 β-甘露聚糖酶的培养基组成和培养条件进行优化 ,在此基础上进行摇瓶补料发酵 ,酶活达223.47U/mL ,较未补料的酶活提高了 32 90 %。酶反应的最适pH为 6 5 ,最适温度为 70℃ ;该酶在pH 5.0～10.0和 70℃以下稳定。水解魔芋胶产物主要为二糖以上低聚糖。     

重组巴氏毕赤酵母高密度发酵表达rHSA

对基因工程菌Pichiapastoris的摇瓶发酵条件进行了试验 ,并根据摇瓶发酵的优化结果进行了补料分批高密度发酵。在摇瓶发酵时 ,甲醇诱导基因工程菌P .pastoris表达重组人血清白蛋白的发酵周期为 96h ;甲醇的最佳诱导浓度为 1 0g L ;发酵pH范围为 5 72～ 6 5 9;在摇瓶培养时 ,随着接种量的增加 ,虽然目的蛋白表达量缓慢增加 ,但单位细胞光密度的蛋白产率却明显下降 ,符合y =1 2 941x- 0 50 59方程 (线性相关系数r=0 9789) ,其限制性因子很可能为溶氧。在分批发酵 ,接种量为 1 0 %且种子细胞光密度 (OD60 0 )为 2 0左右时 ,细胞生长的延迟期为 2 1 1h左右 ,细胞生长光密度与培养时间的关系模型为 :y =0 7841e0 .2 3 19t(线性相关系数r=0 .993 6 ) ;在补料发酵时细胞干重浓度可达到 1 1 5g L— 1 6 0g L ,在 1 2 0h重组人血清白蛋白表达量最大达到 3 6g L。     

毕赤酵母高密度发酵工艺的研究

高密度发酵是毕赤酵母提高蛋白表达量的一种重要策略,发酵工艺是高密度发酵的一个重要因素。采用下列措施均可以有效地提高表达水平：调节基础培养基,采用变pH和变温发酵,提高DO,选择最适的诱导前菌体密度和比生长速率并降低甘油初始浓度和采用分段式指数流加进行调控。选择合适的甲醇补料策略：甲醇限制补料（MLFB）、氧气限制补料（OLFB）、甲醇不限制补料（MNLFB）和温度限制补料（TLFB）。采用两种方式调控补料：诱导阶段菌体生长时,甲醇比消耗速率(qMeOH)为0.02-0.03gg-1h-1,而菌体不生长时,qMeOH采用较高值。     

碱性果胶裂解酶摇瓶发酵条件的研究

利用碱性果胶裂解酶生产菌株Bacillus subtilis WSH02-02进行摇瓶发酵优化,确定了最适种子斜面培养基、种子摇瓶培养基和发酵摇瓶培养基等培养条件,经14h的摇瓶发酵,酶活最高达到8．29U／mL。     

长孢被孢霉利用淀粉质原料发酵产微生物油脂

通过研究长孢被孢霉(Mortierella elongate)的发酵过程,并采用摇瓶分批补料发酵模式考察了起始补料时间及补料基质对长孢被孢霉合成微生物油脂的影响。结果发现该菌株合成油脂主要在发酵48~96 h进行,且N源对菌株的生长有促进作用,采用限氮补料发酵可大幅度提高微生物油脂的产量。最适培养条件:可溶性淀粉20 g/L,玉米浆3 g/L,补料起始时间为发酵48 h,单次补加可溶性淀粉4 g。在此条件下,油脂产量较不补料时增加了521.74 mg,增长率为237.1%。     

Aspergillus sp.脂肪酶发酵条件优化及酶学性质的研究

作者为了得到一种热稳定性较好的脂肪酶新酶种,通过研究分离白极端环境的Aspergillus sp．的最佳产酶条件及其所产脂肪酶的酶学性质,得出了该菌产酶的最佳发酵条件为：以1％黄豆饼粉为氮源、0．2％玉米淀粉为碳源,1．5％橄榄油为诱导物,起始pH6．0左右。装量10mL（250mL三角瓶。摇瓶转速180r／min）、发酵时间为96h。在最佳发酵条件下可得最大发酵酶活36U/mL。Aspergillus sp．所产的脂肪酶的酶学性质是：最适pH为9．0,在pH5．0—10．0于20℃下放置24h后,残余酶活仍保持在起始酶活的90％以上;该酶的最适温度为50℃,50℃保温60min后仍保留70％以上的酶活。Aspergillus sp．所产脂肪酶的热稳定性较好。     

重组大肠杆菌产普鲁兰酶的高密度发酵工艺研究

以表达普鲁兰酶的重组大肠杆菌作为出发菌株,在摇瓶培养的基础上,建立了大肠杆菌工程菌产普鲁兰酶的高密度发酵工艺。通过测定细胞密度、细胞干重、分离菌体可溶性成分与不溶性成分及SDS-PAGE电泳,分析重组大肠杆菌的生长和普鲁兰酶的表达情况。摇瓶试验使用合成培养基和LB培养基,重组大肠杆菌在合成培养基生长较慢,诱导5 h的普鲁兰酶表达量高于LB培养基,包涵体比例低于LB培养基。重组大肠杆菌的高密度发酵使用合成培养基,补料阶段采用指数流加的工艺,在设定细胞的比生长速率为0.12的前提下,限制补料中碳源的供应,以阻止乙酸的产生。当细胞密度OD600达到70.0开始诱导,最终细胞密度为每升53.3 g细胞干重,细胞内可溶性普鲁兰酶为每升1.35 g。     

过量表达自身hemA基因的重组大肠杆菌发酵生产5-氨基乙酰丙酸的研究

研究了优化重组大肠杆菌产5-氨基乙酰丙酸（ALA）的条件,提高大肠杆菌发酵生产AL气的产量。在测定重组大肠杆菌GT48的生长曲线的基础上,确定诱导时间,优化摇瓶发酵条件。然后,进一步在5L发酵罐上进行间歇和流加发酵研究。摇瓶实验表明,细胞培养最佳初始pH为6．5,最佳诱导时间为稳定期前期,最佳接种量为2％,过高的葡萄糖浓度对细胞生长和产物合成均有一定的抑制作用。在5L发酵罐间歇发酵中,重组菌产ALA能力达到47．8mg／L。采用流加发酵可以进一步将产物产量提高到63．8mg／L。构建的过量表达自身的hemA基因的大肠杆菌具有较高的产ALA能力,通过发酵条件优化和采用流加发酵可以提高AL气产量。     

Structured modeling of a microbial system: I. A theoretical study of lactic acid fermentation

Most fermentation models presented in the literature are unstructured, i.e., the biomass composition is assumed constant during all operating conditions. These models are unable to simulate experiments carried out at widely different operating conditions. It is therefore interesting to examine simple structured models where knowledge of the cell physiology is taken into account in the modeling phase. In this article, a simple structured model is presented. The model is based on experimental work with the lactic acid bacteria Streptococcus cremoris, but due to the similarities in basic metabolism for many microorganisms it is applicable also for other fermentation system. The basic assumption in the model is that the biomass can be divided into two parts (compartments)-an active part and a mainly inactive structural part. The size of the active part has a pivotal role in the model.     

丙酸絮凝发酵新工艺研究

报道了丙酸发酵的一种新工艺:絮凝发酵工艺。采用谢氏丙酸杆菌(Propionibacterium shermanii)W125在批次发酵产酸达到29g/L的基础上,选择氢氧化钙作为中和剂兼絮凝剂,建立了絮凝半连续发酵工艺,连续运行250h,产酸量达到了35.4g/L,产酸率提高了22%,糖酸转化率达到了51.56%,体积效率达到了0.37g/(L/h)。     

Relevance of microbial coculture fermentations in biotechnology

The purpose of this article is to review coculture fermentations in industrial biotechnology. Examples for the advantageous utilization of cocultures instead of single cultivations include the production of bulk chemicals, enzymes, food additives, antimicrobial substances and microbial fuel cells. Coculture fermentations may result in increased yield, improved control of product qualities and the possibility of utilizing cheaper substrates. Cocultivation of different micro‐organisms may also help to identify and develop new biotechnological substances. The relevance of coculture fermentations and the potential of improving existing processes as well as the production of new chemical compounds in industrial biotechnology are pointed out here by means of more than 35 examples.     

Optimization of a two-stage recombinant fermentation process: the dilution rate effect

The effects of dilution rates on the performance of a two-stage fermentation system for a recombinant Escherichia coli culture were studied. Dilution rate determines the apparent or averaged specific growth rate of a heterogeneous population of cells in the recombinant culture. The specific growht rate affects the genetic parameters involved in product formation in the second stage, such as plasmid stability, plasmid content, and specific gene expression rate. Kinetic models and correlations were developed for these parameters based on experimental data. Simulations of plasmid stability in the first stage showed that for longer fermentation periods, plasmid stability is better at higher dilution rates. However, the plasmid content is lower at these dilution rates. The optimal apparent specific growth rate for maximum productivity in the second stage was determined using two methods: (1) direct search for a constant specific growth rate, and (2) dynamic optimization using the maximum principle for a time-dependent specific growth rate profile. The results of the calculations showed that the optimum constant apparent specific growth rate for maximum over-all productivity is 0.40 h(-1). This coincides with the optimal specific growht rate for maximum plasmid content in the expressed stage. A 3.5% increase in overall productivity can be obtained by using a linear time dependent apparent specific growth rate control, mu(2)(t) = 0.0007t, in the course of the fermentation time.     

鸟苷补料分批发酵的研究

目的:以枯草芽孢杆菌TA208为出发菌株,研究了补料分批发酵方式下各种参数对鸟苷产量的影响。方法:采用补料分批发酵工艺,利用纸层析法测定发酵液中鸟苷的产量。结果:确定了葡萄糖、酵母粉和次黄嘌呤的最优补料方式,使鸟苷产量达到32.05g/L,较分批发酵方式提高了36.3%。结论:发酵工艺过程控制对发酵生产鸟苷具有重大影响。     

固态间歇补料乙醇生料发酵新工艺

浓醪发酵是酒精生产的发展方向。与现行酒精厂普遍采用的热蒸煮工艺相比, 生料发酵技术的发展使得浓醪发酵更容易进行。本研究首次在生料发酵中直接采用固态原料间歇补料, 比较了STARGENTM生淀粉水解酶间歇补料工艺和传统无补料工艺, 并对不同补料方式进行了研究。结果表明: 与传统无补料生料发酵工艺相比, 在相同的干基配料浓度30%、相同的生料酶添加量0.22%(W/W)的条件下, 采用15%的起始配料浓度、发酵15~25 h进行间歇补料的新工艺, 酒精产量从17.06%提高到18.50%。该间歇补料优化工艺的建立, 丰富了生料发酵技术的应用。     

Optimization of an industrial microalgae fermentation

Optimization of cellular productivity of an industrial microalgae fermentation was investigated. The fermentation was carried out at Coors Biotech Products Company, Fort Collins, Colorado. A mathematical model was developed based on the data collected from pilot plant test runs at different operating conditions. Pontryagin's maximum principle was used for determining the optimal feed policy. A feedback control algorithm was also studied for maximizing the cellular productivity. During continuous operation, the optimum dilution rate was determined by an adaptive optimization scheme based on the steepest descent technique and a recursive least squares estimation of model parameters. A direct search algorithm was also applied to determine the optimum feed rate. Comparison of the theoretical results of the different optimization schemes revealed that the direct search algorithm was preferable because of its simplicity. The experimental results of real time application of the feedback algorithm agreed fairly well with those of the theoretical analyses. (c) 1994 John Wiley & Sons, Inc.