A Soft and Robust Spring Based Triboelectric Nanogenerator for Harvesting Arbitrary Directional Vibration Energy and Self‐Powered Vibration Sensing

Vibration is a common mechanical phenomenon and possesses mechanical energy in ambient environment, which can serve as a sustainable source of power for equipment and devices if it can be effectively collected. In the present work, a novel soft and robust triboelectric nanogenerator (TENG) made of a silicone rubber‐spring helical structure with nanocomposite‐based elastomeric electrodes is proposed. Such a spring based TENG (S‐TENG) structure operates in the contact‐separation mode upon vibrating and can effectively convert mechanical energy from ambient excitation into electrical energy. The two fundamental vibration modes resulting from the vertical and horizontal excitation are analyzed theoretically, numerically, and experimentally. Under the resonant states of the S‐TENG, its peak power density is found to be 240 and 45 mW m^?2 with an external load of 10 MΩ and an acceleration amplitude of 23 m s^?2. Additionally, the dependence of the S‐TENG's output signal on the ambient excitation can be used as a prime self‐powered active vibration sensor that can be applied to monitor the acceleration and frequency of the ambient excitation. Therefore, the newly designed S‐TENG has a great potential in harvesting arbitrary directional vibration energy and serving as a self‐powered vibration sensor.     

An Ultrathin Flexible Single‐Electrode Triboelectric‐Nanogenerator for Mechanical Energy Harvesting and Instantaneous Force Sensing

The trends in miniaturization of electronic devices give rise to the attention of energy harvesting technologies that gathers tiny wattages of power. Here this study demonstrates an ultrathin flexible single electrode triboelectric nanogenerator (S‐TENG) which not only could harvest mechanical energy from human movements and ambient sources, but also could sense instantaneous force without extra energy. The S‐TENG, which features an extremely simple structure, has an average output current of 78 μA, lightening up at least 70 LEDs (light‐emitting diode). Even tapped by bare finger, it exhibits an output current of 1 μA. The detection sensitivity for instantaneous force sensing is about 0.947 μA MPa^?1. Performances of the device are also systematically investigated under various motion types, press force, and triboelectric materials. The S‐TENG has great application prospects in sustainable wearable devices, sustainable medical devices, and smart wireless sensor networks owning to its thinness, light weight, energy harvesting, and sensing capacities.     

Self‐Powered Wireless Sensor Node Enabled by a Duck‐Shaped Triboelectric Nanogenerator for Harvesting Water Wave Energy

This paper presents a fully enclosed duck‐shaped triboelectric nanogenerator (TENG) for effectively scavenging energy from random and low‐frequency water waves. The design of the TENG incorporates the freestanding rolling mode and the pitch motion of a duck‐shaped structure generated by incident waves. By investigating the material and structural features, a unit of the TENG device is successfully designed. Furthermore, a hybrid system is constructed using three units of the TENG device. The hybrid system achieves an instantaneous peak current of 65.5 µA with an instantaneous output power density of up to 1.366 W m^?2. Following the design, a fluid–solid interaction analysis is carried out on one duck‐shaped TENG to understand the dynamic behavior, mechanical efficiency, and stability of the device under various water wave conditions. In addition, the hybrid system is experimentally tested to enable a commercial wireless temperature sensor node. In summary, the unique duck‐shaped TENG shows a simple, cost‐effective, environmentally friendly, light‐weight, and highly stable system. The newly designed TENG is promising for building a network of generators to harvest existing blue energy in oceans, lakes, and rivers.     

Boosting Photoelectrochemical Water Splitting by TENG‐Charged Li‐Ion Battery

The need for cost‐effective and sustainable power supplies has spurred a growing interest in hybrid energy harvesting systems, and the most elementary energy production process relies on intermittent solar power. Here, it is shown how the ambient mechanical energy leads to water splitting in a photoelectrochemical (PEC) cell boosted by a triboelectric nanogenerator (TENG). In this strategy, a flexible TENG collects and transforms mechanical energy into electric current, which boosts the PEC water splitting via the charged Li‐ion battery. Au nanoparticles are deposited on TiO₂ nanoarrays for extending the available light spectrum to visible part by surface plasmon resonance effect, which yields a photocurrent density of 1.32 mA cm^?2 under AM 1.5 G illumination and 0.12 mA cm^?2 under visible light with a bias of 0.5 V. The TENG‐charged battery boosts the water splitting performance through coupling electrolysis and enhanced electron–hole separation efficiency. The hybrid cell exhibits an instantaneous current more than 9 mA with a working electrode area of 0.3 cm², suggesting a simple but efficient route for simultaneously converting solar radiation and mechanical energy into hydrogen.     

Multidirection and Multiamplitude Triboelectric Nanogenerator Composed of Porous Conductive Polymer with Prolonged Time of Current Generation

In this work, a sponge structure triboelectric nanogenerator (TENG) named as porous conductive polymer (PCP)‐TENG, is demonstrated. The measured volume charge density of PCP‐TENG is reached to 60 mC m^?3 by utilizing wide inner surface of the sponge structure as contact surface. Moreover, the PCP‐TENG generates a continuous sinusoidal‐like alternative current. Notably, the PCP‐TENG can effectively harvest vibrational mechanical energy from various directions and amplitudes. With these characteristics, the PCP‐TENG can be implemented in a wide variety of settings, such as inside of a tire. It is confirmed that the PCP‐TENG generates electrical power for operating a commercial light‐emitting diode and a humidity sensor even under small deformation of the tire.     

Tribovoltaic Effect on Metal–Semiconductor Interface for Direct‐Current Low‐Impedance Triboelectric Nanogenerators

The triboelectric nanogenerator (TENG) is a new energy technology that is enabled by coupled contact electrification and electrostatic induction. The conventional TENGs are usually based on organic polymer insulator materials, which have the limitations and disadvantages of high impedance and alternating output current. Here, a tribovoltaic effect based metal–semiconductor direct‐current triboelectric nanogenerator (MSDC‐TENG) is reported. The tribovoltaic effect is facilitated by direct voltage and current by rubbing a metal/semiconductor on another semiconductor. The frictional energy released by the forming atomic bonds excites nonequilibrium carriers, which are directionally separated to form a current under the built‐in electric field. The continuous average open‐circuit voltage (10–20 mV), short‐circuit direct‐current output (10–20 µA), and low impedance characteristic (0.55–5 kΩ) of the MSDC‐TENG can be observed during relative sliding of the metal and silicon. The working parameters are systematically studied for electric output and impedance characteristics. The results reveal that faster velocity, larger pressure, and smaller area can improve the maximum power density. The internal resistance is mainly determined by the velocity and the electrical resistance of semiconductor. This work not only expands the material candidates of TENGs from organic polymers to semiconductors, but also demonstrates a tribovoltaic effect based electric energy conversion mechanism.     

Rotating‐Disk‐Based Direct‐Current Triboelectric Nanogenerator

An innovative design is reported of a direct‐current triboelectric nanogenerator (DC‐TENG) based on a rotating disk design for harvesting rotational mechanical energy. The DC‐TENG consists of two disks and two pairs of flexible electric brushes that are made of carbon fiber and contact two electrodes, respectively. During the rotation, two disks have distinct triboelectric polarities for a cyclic in‐plane charge separation between them and an alternating current is generated between the two electrodes. Because of the sliding contact and automatically switch between the electric brushes and the two electrodes, the current is reversed in the second half of the cycle and a direct current is generated. The role that the rotating speed and the segmentation number have is thoroughly investigated and shows that there is direct current enhancement not only at higher speed but also with more segments. The DC‐TENG has been demonstrated as a constant current source for directly and continuously driving electronic devices and/or charging an energy storage unit without a rectifier bridge. This work presents a novel DC‐TENG technology and opens up more potential applications for harvesting rotational mechanical energy and powering electronics.     

Energy Harvesting from Breeze Wind (0.7–6 m s−1) Using Ultra‐Stretchable Triboelectric Nanogenerator

Wind is one of the most important sources of green energy, but the current technology for harvesting wind energy is only effective when the wind speed is beyond 3.5–4.0 m s^?1. This is mainly due to the limitation that the electromagnetic generator works best at high frequency. This means that light breezes cannot reach the wind velocity threshold of current wind turbines. Here, a high‐performance triboelectric nanogenerator (TENG) for efficiently harvesting energy from an ambient gentle wind, especially for speeds below 3 m s^?1 is reported, by taking advantage of the relative high efficiency of TENGs at low‐frequency. Attributed to the multiplied‐frequency vibration of ultra‐stretchable and perforated electrodes, an average output of 20 mW m^?3 can be achieved with inlet wind speed of 0.7 m s^?1, while an average energy conversion efficiency of 7.8% at wind speed of 2.5 m s^?1 is reached. A self‐charging power package is developed and the applicability of the TENG in various light breezes is demonstrated. This work demonstrates the advantages of TENG technology for breeze energy exploitation and proposes an effective supplementary approach for current employed wind turbines and micro energy structure.     

Sustainable Energy Source for Wearable Electronics Based on Multilayer Elastomeric Triboelectric Nanogenerators

Wearable electronics have attracted a wide range of attention with various functions due to the development of semiconductor industry and information technology. This work focuses on a triboelectric nanogenerator‐based self‐charging power system as a continuous energy source for wearable electronics. The triboelectric nanogenerator has a multilayer elastomeric structure with closely stacked arches as basic functional units. Owing to material and structural innovations, this triboelectric nanogenerator performs outstanding electric output with the maximum volume charge density ≈0.055 C m^?3 and practical properties for energy harvesting from body motions. Utilizing the triboelectric nanogenerator as outsole to harvest energy from walking or jogging, a pair of shoes is fabricated with the maximum equivalent charge current of each shoe being around 16.2 µA and specific fitness functions realized on each shoe separately without complex connections.     

Multiple‐Frequency High‐Output Triboelectric Nanogenerator Based on a Water Balloon for All‐Weather Water Wave Energy Harvesting

Energy and the environment are two of the main issues facing the world today. As a consequence abundant renewable green energy sources such as wave energy, have become hot topics. Here, a multiple‐frequency triboelectric nanogenerator based on the water balloon (WB‐TENG) is proposed for harvesting water wave energy in any direction. Owing to the high elasticity of the water balloon, the WB‐TENG can realize a multiple‐frequency response to low‐frequency external mechanical simulations to generate high‐frequency electrical output. In addition, the water balloon can achieve self‐support without any additional supporting structure because of its tension, to make WB‐TENG still produce electrical output under slight vibration, which can also bring high energy conversion efficiency. Moreover, the fabricated WB‐TENG generates a maximum instantaneous short‐circuit current and an open‐circuit voltage of 147 µA and 1221 V, respectively. Most noteworthy, under the same conditions, the total transferred charge of WB‐TENG is 28 times than that of traditional TENG based on double plate structure during one working cycle. Therefore, this design can provide an effective way to promote the development of TENGs in blue energy.     

Long‐Lifetime Triboelectric Nanogenerator Operated in Conjunction Modes and Low Crest Factor

The high‐output triboelectric nanogenerator (TENG) is indispensable for its practical applications toward industrial products. However, the electricity loss in simple parallel connection among all units and the typically high crest factor output seriously hamper the practical applications of TENG. Here, a rectified TENG is reported in parallel structure to solve the problem of electricity loss in simple parallel connection. The rotational contact–separation structure with phase difference between rectified TENGs addresses high crest factor output and extends service life of rotational TENG simultaneously. The current crest factor is dramatically decreased to 1.31 in multiple rectifier multiple TENG in parallel (MRM‐TENG), while that of TENG in simple parallel is higher than 6. Meanwhile, the current output can retain up to ≈93% of its initial performance after 7 200 000 rotations under 2.00 r s^?1 of 1000 h. Furthermore, the equivalent current can be in linear growth with low crest factor by making MRM‐TENG in parallel for distributed energy supply without electricity loss. This work may provide a new strategy for TENG in parallel to achieve a low crest factor output and long‐term cycling stability power generation in distributed energy harvesting for large‐scale power application.     

High‐Output Triboelectric Nanogenerator Based on Dual Inductive and Resonance Effects‐Controlled Highly Transparent Polyimide for Self‐Powered Sensor Network Systems

High‐output triboelectric nanogenerators (TENGs) are demonstrated based on polyimide (PI)‐based polymers by introducing functionalities (e.g., electron‐withdrawing and electron‐donating groups) into the backbone. The TENG based on 6FDA‐APS PI, possessing the most negative electrostatic potential and the low‐lying lowest unoccupied molecular orbital level, produces the highest effective charge density of about 860 µC m^?2 in practical working conditions with the ion injection process. This may be ascribed to the excellent charge‐retention characteristics as well as the enhanced charge transfer capability, which increases the output power by 7 times compared to the commercially available Kapton film‐based TENG. Finally, a 6FDA‐APS‐driven sensor network system is demonstrated, providing the identity of three gases (H₂, CO, and NO₂) by illuminating the light‐emitting diodes within several seconds.     

Natural Leaf Made Triboelectric Nanogenerator for Harvesting Environmental Mechanical Energy

Distributed environmental mechanical energy is rarely collected due to its fluctuating amplitudes and low frequency, which is usually attributed as “random” energy. Considering the rapid development of the Internet of things (IoT), there is a great need for a large number of distributed and sustainable power sources. Here, a natural leaf assembled triboelectric nanogenerator (Leaf‐TENG) is designed by utilizing the green leaf as an electrification layer and electrode to effectively harvest environmental mechanical energy. The Leaf‐TENG with good adaptability has the maximum output power of ≈45 mW m^?2, which is capable of driving advertising LEDs and commercial electronic temperature sensors. Besides, a tree‐shaped energy harvester is integrated with natural Leaf‐TENG to harvest large‐area environmental mechanical energy. This work provides a new prospect for distributed and environmental‐friendly power sources and has potential applications in the IoT and self‐powered systems.     

Environmentally Friendly Hydrogel‐Based Triboelectric Nanogenerators for Versatile Energy Harvesting and Self‐Powered Sensors

Triboelectric nanogenerators (TENGs), as a promising energy harvesting technology, have been rapidly developed in recent years. However, the research based on fully flexible and environmentally friendly TENGs is still limited. Herein, for the first time, a hydrogel‐based triboelectric nanogenerator (Hydrogel‐TENG) with high flexibility, recyclability, and environmental friendliness simultaneously has been demonstrated. The standard Hydrogel‐TENG can generate a maximum output power of 2 mW at a load resistance of 10 MΩ. The tube‐shaped Hydrogel‐TENG can harvest mechanical energy from various human motions, including bending, twisting, and stretching. Furthermore, the system can serve as self‐powered sensors to detect the human motions. Additionally, the utilized Polyvinyl Alcohol hydrogel employed in this study is recyclable to benefit for fabricating the renewable TENG. The open‐circuit voltage of renewed hydrogel‐TENG can reach up to 92% of the pristine output voltage. This research will pave a potential approach for the development of flexible energy sources and self‐powered motion sensors in environmentally friendly way.     

Triboelectric Nanogenerator for Sustainable Wastewater Treatment via a Self‐Powered Electrochemical Process

By harvesting the flowing kinetic energy of water using a rotating triboelectric nanogenerator (R‐TENG), this study demonstrates a self‐powered wastewater treatment system that simultaneously removes rhodamine B (RhB) and copper ions through an advanced electrochemical unit. With the electricity generated by R‐TENG, the removal efficiency (RE) of RhB can reach the vicinity of 100% within just 15 min when the initial concentration of RhB is around 100 ppm at optimized conditions. The removal efficiency of copper ions can reach 97.3% after 3 h within an initial concentration of 150 ppm at an optimized condition. Importantly, a better performance and higher treating efficiency are found by using the pulsed output of R‐TENG than those using direct current (DC) supply for pollutant removal when consuming equal amount of energy. The recovered copper layer on the cathode through R‐TENG is much denser, more uniform, and with smaller grain size (d = 20 nm) than those produced by DC process, which also hints at very promising applications of the R‐TENG in electroplating industry. In light of the merits such as easy portability, low cost, and effectiveness, this R‐TENG‐based self‐powered electrochemical system holds great potential in wastewater treatment and electroplating industry.     

Honeycomb Structure Inspired Triboelectric Nanogenerator for Highly Effective Vibration Energy Harvesting and Self‐Powered Engine Condition Monitoring

Vibration in mechanical equipment can serve as a sustainable energy source to power sensors and devices if it can be effectively collected. In this work, a honeycomb structure inspired triboelectric nanogenerator (HSI‐TENG) consisting of two copper electrode layers with sponge bases and one honeycomb frame filled with polytetrafluoroethylene (PTFE) balls is proposed to harvest vibration energy. The application of a compact honeycomb structure increases the maximum power density of HSI‐TENG by 43.2% compared to the square grid structure and provides superior advantages in large‐scale manufacturing. More importantly, the nonspring‐assisted HSI‐TENG can generate electricity once the PTFE balls obtain sufficient kinetic energy to separate from the bottom electrode layer regardless of the vibration frequency and direction. This is fundamentally different from the spring‐assisted harvesters that can only work around their natural frequencies. The vibration model and working criteria of the HSI‐TENG are established. Furthermore, the HSI‐TENG is successfully used to serve as a self‐powered sensor to monitor engine conditions by analyzing the electrical output of the HSI‐TENG installed on a diesel engine. Therefore, the nonspring‐assisted HSI‐TENG provides a novel strategy for highly effective vibration energy harvesting and self‐powered machinery monitoring.     

Broadband Vibrational Energy Harvesting Based on a Triboelectric Nanogenerator

Vibrations in living environments are generally distributed over a wide frequency spectrum and exhibit multiple motion directions over time, which renders most of the current vibration energy harvesters unpractical for their harvesting purposes. Here, a 3D triboelectric nanogenerator (3D‐TENG) is designed based on the coupling of the triboelectrification effect and the electrostatic induction effect. The 3D‐TENG operates in a hybridization mode of conjuntioning the vertical contact‐separation mode and the in‐plane sliding mode. The innovative design facilitates harvesting random vibrational energy in multiple directions over a wide bandwidth. An analytical model is established to investigate the mechano‐triboelectric transduction of 3D‐TENG and the results agree well with experimental data. The 3D‐TENG is able to harvest ambient vibrations with an extremely wide working bandwidth. Maximum power densities of 1.35 W m^‐2 and 1.45 W m^‐2 are achieved under out‐of‐plane and in‐plane excitation, respectively. The 3D TENG is designed for harvesting ambient vibration energy, especially at low frequencies, under a range of conditions in daily life and has potential applications in environmental/infrastructure monitoring and charging portable electronics.     

A Self‐Powered Dynamic Displacement Monitoring System Based on Triboelectric Accelerometer

An integrated self‐powered dynamic displacement monitoring system by utilizing a novel triboelectric accelerometer for structural health monitoring is proposed and implemented in this study, which can show the dynamic displacement and transmit the alarming signal by accurately sensing the vibration acceleration. The fabricated triboelectric accelerometer based on the noncontact freestanding triboelectric nanogenerator consists of an outer transparent sleeve tube and an inner cylindrical inertial mass that is suspended by a highly stretchable silicone fiber. One pair of copper film electrodes is deposited by physical vapor deposition on nylon film and adhered on the inner wall of the outer tube, while a fluorinated ethylene propylene film with nanowire structures is adhered on the surface of the inner cylindrical inertial mass. The experimental results show that proposed triboelectric accelerometer can accurately sense the vibration acceleration with a high sensitivity of 0.391 V s² m^?1. In particular, the developed accelerometer has superior performance within the low‐frequency range. One of the most striking features is that the commercial accelerometer using piezoelectric material is strongly dominated by high‐order harmonics, which can cause confusion in computer data analysis. In contrast, the triboelectric accelerometer is only dominated by the base resonance mode.     

Metal–Organic Framework: A Novel Material for Triboelectric Nanogenerator–Based Self‐Powered Sensors and Systems

The triboelectric nanogenerator (TENG) offers a simple and cost‐effective method to harness waste energy and works on the principle of contact electrification and electrostatic induction. The performance and application of TENG depend to a great extent on the material used for fabrication. The most widely used materials include polymers and a few metals, well‐arranged in the triboelectric series so as to promote electrification upon contact. New triboelectric materials are important for extending the applications and specificity of the TENG. A TENG based on a metal–organic framework (MOF) of the zeolitic imidazole family is reported here. The zeolitic imidazole framework‐8 (ZIF‐8) and Kapton are used as the active materials for MOF–TENG fabrication. Surface potential, structural, morphological and electrical measurements reveals detailed characteristics of ZIF‐8, confirming the MOF as a potential candidate for TENG applications. The MOF–TENG generates a sustainable output of 164 V and 7 µA in vertical contact–separation mode. Finally, a self‐powered UV counterfeit system and a tetracycline sensor are successfully developed and demonstrated with the MOF–TENG. The sensor is highly selective and reusable simply by washing.     

Microdischarge‐Based Direct Current Triboelectric Nanogenerator via Accumulation of Triboelectric Charge in Atmospheric Condition

Direct conversion of mechanical energy into direct current (DC) by triboelectric nanogenerators (TENGs) is one of the desired features in terms of energy conversion efficiency. Although promising applications have been reported using the triboelectric effect, effective DC generating TENGs must be developed for practical purposes. Here, it is reported that continuous DC generation within a TENG itself, without any circuitry, can be achieved by triggering air breakdown via triboelectrification. It is demonstrated that DC generation occurs in combination with i) charge accumulation to generate air breakdown, ii) incident discharge (microdischarge), and iii) conveyance of charges to make the device sustainable. 10.5 mA m^?2 of output current and 10.6 W m^?2 of output power at 33 MΩ load resistance are achieved. Compared to the best DC generating TENGs ever reported, the TENG in this present study generates about 20 times larger root‐mean square current density.