采用玉米秸秆水解糖和玉米浆发酵生产丁二酸

研究了以玉米秸秆水解糖为碳源,不同氮源条件下琥珀酸放线杆菌Actinobacillus succinogenesSF-9的丁二酸发酵产酸能力。结果表明玉米浆可以替代酵母膏作为丁二酸发酵的廉价氮源。厌氧摇瓶丁二酸发酵单因素试验,得到在初糖浓度50 g/L时,玉米浆的较佳用量为20 g/L。在5 L搅拌罐上,考察了不同初始玉米秸秆水解糖浓度对A.succinogenes SF-9发酵生产丁二酸的影响,结果显示高初始秸秆糖浓度对琥珀酸放线杆菌的生长有抑制作用。采用补料分批发酵,发酵60 h丁二酸的产量达到42.7g/L,丁二酸产率82.7%,生产强度0.81 g/(L·h)。丁二酸的产量和生产强度较分批发酵有明显提高。     

稀酸水解玉米芯制备丁二酸

利用正交设计得到稀H2SO4水解玉米芯制备混合糖液的优化工艺:玉米芯料液比1∶5(质量体积比),物料粒径250~380μm、H2SO4用量3%(体积分数)、水解温度126℃、反应时间2.5 h。此工艺条件下的总糖收率达90%,总糖质量浓度为60 g/L,发酵抑制物糠醛含量为0.87 g/L,5-羟甲基糠醛含量为0.68 g/L。在此基础上利用活性炭吸附和Ca(OH)2中和对玉米芯混合糖液进行脱毒及脱盐处理,SO42-脱除率达96%,色素脱除率为96%,糠醛、5-羟甲基糠醛及多酚类物质脱除率均高于50%。处理后的玉米芯多组分糖液作为产琥珀酸放线杆菌(Actinobacillus succino-genes)NJ113的发酵C源,当培养基中初始总糖质量浓度为50 g/L时,丁二酸收率为61.68%,丁二酸质量浓度为30.8 g/L;初始总糖质量浓度为70 g/L时,丁二酸收率仍可达50%以上,丁二酸质量浓度为35.2 g/L。发酵实验表明,将经过脱毒脱盐处理的玉米芯多组分糖液替代葡萄糖作为C源发酵制备丁二酸具有可行性。     

Fermentation of lignocellulosic sugars to acetic acid by <Emphasis Type="Italic">Moorella thermoacetica</Emphasis>

A systematic study of bioconversion of lignocellulosic sugars to acetic acid by Moorella thermoacetica (strain ATCC 39073) was conducted. Four different water-soluble fractions (hydrolysates) obtained after steam pretreatment of lignocellulosic biomass were selected and fermented to acetic acid in batch fermentations. M. thermoacetica can effectively ferment xylose and glucose in hydrolysates from wheat straw, forest residues, switchgrass, and sugarcane straw to acetic acid. Xylose and glucose were completely utilized, with xylose being consumed first. M. thermoacetica consumed up to 62 % of arabinose, 49 % galactose and 66 % of mannose within 72 h of fermentation in the mixture of lignocellulosic sugars. The highest acetic acid yield was obtained from sugarcane straw hydrolysate, with 71 % of theoretical yield based on total sugars (17 g/L acetic acid from 24 g/L total sugars). The lowest acetic acid yield was observed in forest residues hydrolysate, with 39 % of theoretical yield based on total sugars (18 g/L acetic acid from 49 g/L total sugars). Process derived compounds from steam explosion pretreatment, including 5-hydroxymethylfurfural (0.4 g/L), furfural (0.1 g/L) and total phenolics (3 g/L), did not inhibit microbial growth and acetic acid production yield. This research identified two major factors that adversely affected acetic acid yield in all hydrolysates, especially in forest residues: (i) glucose to xylose ratio and (ii) incomplete consumption of arabinose, galactose and mannose. For efficient bioconversion of lignocellulosic sugars to acetic acid, it is imperative to have an appropriate balance of sugars in a hydrolysate. Hence, the choice of lignocellulosic biomass and steam pretreatment design are fundamental steps for the industrial application of this process.     

Improvement of kojic acid production in Aspergillus oryzae B008 mutant strain and its uses in fermentation of concentrated corn stalk hydrolysate

A strain designated M866, producing kojic acid with a high yield, was obtained by combining induced mutation using ion beam implantation and ethyl methane sulfonate treatment of a wild type strain of Aspergillus oryzae B008. The amount of kojic acid produced by the strain M866 in a shaking flask was 40.2 g/L from 100 g/L of glucose, which was 1.7 times higher than that produced by wild strain (23.58 g/L). When the mixture of glucose and xylose was used as carbon source, the resulting kojic acid production was raised with the increasing of glucose ratios in the mixture. With concentrations of glucose at 75 g/L and xylose at 25 g/L mixed in the medium, the production of kojic acid reached 90.8 %, which was slightly lower than with glucose as the sole source of carbon. In addition, the kojic acid fermentation of the concentrated hydrolysate from corn stalk was also investigated in this study, the maximum concentration of kojic acid accumulated at the end of the fermentation was 33.1 g/L and this represents the yield based on reducing sugar consumed and the overall productivity of 0.36 g/g and 0.17 g/L/h, respectively.     

A complete industrial system for economical succinic acid production by Actinobacillus succinogenes

An industrial fermentation system using lignocellulosic hydrolysate, waste yeast hydrolysate, and mixed alkali to achieve high-yield, economical succinic acid production by Actinobacillus succinogenes was developed. Lignocellulosic hydrolysate and waste yeast hydrolysate were used efficiently as carbon sources and nitrogen source instead of the expensive glucose and yeast extract. Moreover, as a novel method for regulating pH mixed alkalis (Mg(OH)₂ and NaOH) were first used to replace the expensive MgCO₃ for succinic acid production. Using the three aforementioned substitutions, the total fermentation cost decreased by 55.9%, and 56.4 g/L succinic acid with yield of 0.73 g/g was obtained, which are almost the same production level as fermentation with glucose, yeast extract and MgCO₃. Therefore, the cheap carbon and nitrogen sources, as well as the mixed alkaline neutralize could be efficiently used instead of expensive composition for industrial succinic acid production.     

Conversion of acid hydrolysate of oil palm empty fruit bunch to L-lactic acid by newly isolated Bacillus coagulans JI12

Cost-effective conversion of lignocellulose hydrolysate to optically pure lactic acid is commercially attractive but very challenging. Bacillus coagulans JI12 was isolated from natural environment and used to produce L-lactic acid (optical purity?>?99.5 %) from lignocellulose sugars and acid hydrolysate of oil palm empty fruit bunch (EFB) at 50 °C and pH 6.0 without sterilization of the medium. In fed-batch fermentation with 85 g/L initial xylose and 55 g/L xylose added after 7.5 h, 137.5 g/L lactic acid was produced with a yield of 98 % and a productivity of 4.4 g/L?h. In batch fermentation of a sugar mixture containing 8.5 % xylose, 1 % glucose, and 1 % L-arabinose, the lactic acid yield and productivity reached 98 % and 4.8 g/L?h, respectively. When EFB hydrolysate was used, 59.2 g/L of lactic acid was produced within 9.5 h at a yield of 97 % and a productivity of 6.2 g/L?h, which are the highest among those ever reported from lignocellulose hydrolysates. These results indicate that B. coagulans JI12 is a promising strain for industrial production of L-lactic acid from lignocellulose hydrolysate.     

发酵产丁二酸过程中废弃细胞的循环利用

对厌氧发酵产丁二酸后的废弃细胞进行破壁处理,考察了以细胞水解液作为有机氮源重新用于丁二酸发酵的可行性。比较了超声破碎、盐溶、酶解3种方法破碎细胞获得的水解液作为氮源发酵产丁二酸的效果,结果表明酶解制得的细胞水解液效果最佳。以总氮含量为1.11g/L的酶解液(相当于10g/L酵母膏)作为氮源发酵,丁二酸产量可达42.0g/L,继续增大酶解液用量对耗糖、产酸能力没有显著提高。将细胞酶解液与5g/L酵母膏联用发酵36h后,丁二酸产量达75.5g/L,且丁二酸生产强度为2.10g/(L·h),比使用10g/L酵母膏时提高了66.7%。因此,厌氧发酵产丁二酸结束后的废弃细胞酶解液可以替代原培养基中50%的酵母膏用于发酵。     

Succinic acid production by <Emphasis Type="Italic">Actinobacillus succinogenes</Emphasis> from batch fermentation of mixed sugars

Succinic acid production from the monosaccharides xylose, arabinose, glucose, mannose and galactose was studied using the bacterium Actinobacillus succinogenes. In Duran bottle cultures, containing 10 g/L of each of sugar, succinic acid was produced from all sugars except for galactose. The highest succinate yield, 0.56 g/g, was obtained with glucose, whereas the succinate yield was 0.42, 0.38 and 0.44 g/g for xylose, mannose and arabinose, respectively. The specific succinate productivity was 0.7 g/g h for glucose, but below 0.2 g/g h for the other sugars. Batch bioreactor fermentations were carried out using a sugar mixture of the five sugars giving a total concentration of 50 g/L, mimicking the distribution of sugars in spent sulfite liquor (SSL) from Eucalyptus which is rich in xylose. In this mixture, an almost complete conversion of all sugars (except galactose) was achieved resulting in a final succinate concentration of 21.8–26.8 g/L and a total yield of 0.59–0.68 g/g. There was evidence of co-consumption of glucose and xylose, whereas mannose was consumed after glucose. The main by-products were acetate 0.14–0.20 g/g and formate 0.08–0.13 g/g. NADH balance calculations suggested that NADH required for succinate production was not met solely from formate and acetate production, but other means of NADH production was necessary. Results from mixed sugar fermentations were verified using SSL as substrate resulting in a succinate yield of 0.60 g/g. In addition, it was found that CO₂ sparging could replace carbonate supply in the form of MgCO₃ without affecting the succinate yield.     

Beneficial Effect of Corncob Acid Hydrolysate on the Lipid Production by Oleaginous Yeast Trichosporon dermatis

In this work, corncob acid hydrolysate and its simulated medium whose sugar composition was the same as the corncob acid hydrolysate were used as fermentation substrate for lipid production by oleaginous yeast Trichosporon dermatis. On the corncob acid hydrolysate, after 7 days of fermentation, the biomass, lipid content, lipid yield, and lipid coefficient of T. dermatis were 17.3 g/L, 40.2%, 7.0 g/L, and 16.5%, respectively. Interestingly, during the lipid fermentation on the corncob acid hydrolysate, glucose, xylose, arabinose, and even acetic acid could be well utilized as carbon sources by T. dermatis. Surprisingly, the lipid yield (7.0 g/L) of T. dermatis on the corncob acid hydrolysate was much higher than that (3.8 g/L) on the simulated medium, in spite of the fact that the lipid coefficient (17.4%) on the simulated medium was a little higher. This phenomenon further showed that lignocellulosic acid hydrolysate was a suitable substrate for lipid fermentation by T. dermatis. This work would help the comprehensive utilization of lignocellulosic biomass for lipid production.     

Development of succinic acid production from corncob hydrolysate by <Emphasis Type="Italic">Actinobacillus succinogenes</Emphasis>

Succinic acid is one of the most important platform chemicals since it has great potential in industrial applications. In this study, corncob hydrolysate was used for succinic acid production. After diluted acid treatment, xylose was released from hemicellulose as the predominant monosaccharide in the hydrolysate, whereas glucose was released very little and most was retained as cellulose in the raw material. Without any detoxification, corncob hydrolysate was used directly as the carbon source in the fermentation. Actinobacillus succinogenes could utilize the sugars in the hydrolysate to produce succinic acid efficiently. Through medium optimization, yeast extract was selected as the nitrogen source and MgCO₃ was used to control pH. A total of 23.64 g/l of succinic acid was produced with a yield of 0.58 g/g based on consumed sugar, indicating that the waste corncob residue can be used to produce value-added chemicals practically.     

Production of succinic acid and lactic acid by Corynebacterium crenatum under anaerobic conditions

A new succinic acid and lactic acid production bioprocess by Corynebacterium crenatum was investigated in mineral medium under anaerobic conditions. Corynebacterium crenatum cells with sustained acid production ability and high acid volumetric productivity harvested from the glutamic acid fermentation broth were used to produce succinic acid and lactic acid. Compared with the first cycle, succinic acid production in the third cycle increased 120% and reached 43.4 g/L in 10 h during cell-recycling repeated fermentations. The volumetric productivities of succinic acid and lactic acid could maintain above 4.2 g/(L·h) and 3.1 g/(L·h), respectively, for at least 100 h. Moreover, wheat bran hydrolysates could be used for succinic acid and lactic acid production by the recycled C. crenatum cells. The final succinic acid concentration reached 43.6 g/L with a volumetric productivity of 4.36 g/(L·h); at the same time, 32 g/L lactic acid was produced.     

Batch and continuous fermentation of succinic acid from wood hydrolysate by Mannheimia succiniciproducens MBEL55E

Batch and continuous cultures of Mannheimia succiniciproducens MBEL55E were carried out in a complex medium containing a NaOH-treated wood hydrolysate for the production of succinic acid. The wood hydrolysate based medium was treated with NaOH before sterilization to reduce the formation of inhibitory compounds. M. succiniciproducens MBEL55E utilized xylose as well as glucose in the wood hydrolysate based medium as a carbon source for the succinic acid production. In batch cultures, the final succinic acid concentration of 11.73 g l⁻¹ was obtained from the pre-treated wood hydrolysate based medium, resulting in a succinic acid yield of 56% and a succinic acid productivity of 1.17 g l⁻¹ h⁻¹, while the corresponding continuous cultures gave the succinic acid yield and productivity of 55% and 3.19 g l⁻¹ h⁻¹, respectively. These results suggest that succinic acid can be produced economically and efficiently by the fermentation of M. succiniciproducens MBEL55E from an inexpensive biomass-based wood hydrolysate.     

Simultaneous saccharification and fermentation of acid-pretreated rapeseed meal for succinic acid production using Actinobacillus succinogenes

Rapeseed meal was evaluated for succinic acid production by simultaneous saccharification and fermentation using Actinobacillus succinogenes ATCC 55618. Diluted sulfuric acid pretreatment and subsequent hydrolysis with pectinase was used to release sugars from rapeseed meal. The effects of culture pH, pectinase loading and yeast extract concentration on succinic acid production were investigated. When simultaneous saccharification and fermentation of diluted acid pretreated rapeseed meal with a dry matter content of 12.5% (w/v) was performed at pH 6.4 and a pectinase loading of 2% (w/w, on dry matter) without supplementation of yeast extract, a succinic acid concentration of 15.5 g/L was obtained at a yield of 12.4 g/100g dry matter. Fed-batch simultaneous saccharification and fermentation was carried out with supplementation of concentrated pretreated rapeseed meal and pectinase at 18 and 28 h to yield a final dry matter content of 20.5% and pectinase loading of 2%, with the succinic acid concentration enhanced to 23.4 g/L at a yield of 11.5 g/100g dry matter and a productivity of 0.33 g/(Lh). This study suggests that rapeseed meal may be an alternative substrate for the efficient production of succinic acid by A. succinogenes without requiring nitrogen source supplementation.     

Production of biobutanol from acid-pretreated corncob using Clostridium beijerinckii TISTR 1461: Process optimization studies

Corncob is a potential feedstock in Thailand that can be used for fermentable sugar production through dilute sulfuric acid pretreatment and enzymatic hydrolysis. To recover high amounts of monomeric sugars from corncob, the sulfuric pretreatment conditions were optimized by using response surface methodology with three independent variables: sulfuric acid concentration, temperature, and time. The highest response of total sugars, 48.84 g/L, was found at 122.78°C, 4.65 min, and 2.82% (v/v) H₂SO₄. With these conditions, total sugars from the confirmation experiment were 46.29 g/L, with 5.51% error from the predicted value. The hydrolysate was used as a substrate for acetone–butanol–ethanol fermentation to evaluate its potential for microbial growth. The simultaneous saccharification and fermentation (SSF) showed that C. beijerinckii TISTR 1461 can generate acetone–butanol–ethanol products at 11.64 g/L (5.29 g/L acetone, 6.26 g/L butanol, and 0.09 g/L ethanol) instantly using sugars from the hydrolysed corncob with Novozymes 50013 cellulase enzyme without an overliming process.     

糠醛和5-羟甲基糠醛对大肠杆菌产丁二酸的影响

利用可再生生物质特别是木质纤维素水解液来生产平台化合物丁二酸,是目前研究的热点。虽然许多研究者相继报道了木质纤维素水解液对菌株生长和丁二酸生产存在一定抑制作用,但并没有水解液中各种抑制物对菌株影响的相关动力学研究及机理研究。我们选择了两种代表性木质纤维素水解液抑制物,即糠醛和5-羟甲基糠醛,系统研究了它们对大肠杆菌的生长和丁二酸生产的影响。结果表明：糠醛和5-羟甲基糠醛的初始抑制浓度均为0.8 g/L。当糠醛浓度大于6.4 g/L,5-羟甲基糠醛浓度大于12.8 g/L时,菌株生长完全受到抑制。在最高耐受浓度下,糠醛的存在使菌株生物量比对照菌株下降77.8%,丁二酸产量下降36.1%。5-羟甲基糠醛的存在使菌株生物量比对照菌株降低13.6%,丁二酸产量降低18.3%。糠醛和5-羟甲基糠醛具有明显的协同作用。体外酶活测定表明丁二酸生产途径中关键酶磷酸烯醇式丙酮酸羧化酶、苹果酸脱氢酶、富马酸还原酶均受糠醛和5-羟甲基糠醛抑制。研究结果对丁二酸生产用纤维素水解液的预处理和脱毒工艺开发具有指导作用,有利于实现丁二酸发酵生产的工业化。     

Homogeneous solid dispersion (HSD) system for rapid and stable production of succinic acid from lignocellulosic hydrolysate

Continuous bio-production of succinic acid was reported in homogeneous solid dispersion (HSD) system utilizing porous coconut shell activated carbon (CSAC) as immobilization carrier. The aim of the present work was to implement the HSD system to increase the area of cell immobilization and the rate of succinic-acid production from the lignocellulosic medium. The ratio of the two enzymes (cellulase-to-hemicellulase) was initially optimized to break down the lignocellulose into its free monomers, wherein the best ratio was determined as 4:1. Succinic-acid production was evaluated in the HSD system by varying the substrate loading and dilution rate. The results showed that high productivities of succinic acid were obtained when 60 g/L glucose was fed over a dilution rates ranging from 0.03 to 0.4/h. The titer of succinic acid decreased gradually with higher dilution rate, whereas the residual substrate concentration increased with it. Critical dilution rate was determined to be 0.4/h at which the best productivity of succinic acid of 6.58 g/L h and its yield of 0.66 g/g were achieved using oil palm fronds (OPF) hydrolysate. This work lends evidence to the use of CSAC and lignocellulosic hydrolysate to further exploit the potential economies of scale.

     

玉米芯稀酸水解及L-乳酸发酵研究

对玉米芯稀硫酸水解条件及糖化液发酵L-乳酸进行了初步研究。结果表明,玉米芯木聚糖最适水解条件为2%H2SO_4、120℃、30 min、固液比1:10,糖化液还原糖含量可达40.8 g/L,主要成分为木塘。细菌A-19可以利用水解液中的葡萄糖和木糖产酸,最适发酵条件为45℃、pH 6.5,从45℃～51℃、pH 5.5～pH 6.5产量均较高。用未浓缩的水解液发酵24 h,L-乳酸产量为30.6g/L,残糖为1.6 g/L,糖酸转化率为82.6%;用浓缩1倍的水解液发酵48 h,L-乳酸产量为41.4 g/L,残糖4.1g/L,糖酸转化率为68.2%,在发酵48 h后继续补料发酵至72 h(补料液为浓缩3倍的水解液),L-乳酸产量为50.9 g/L,残糖6.3 g/L,糖酸转化率为71.8%。该研究为利用木质纤维素生产L-乳酸奠定了一定基础。     

A novel isolate of <Emphasis Type="Italic">Clostridium butyricum</Emphasis> for efficient butyric acid production by xylose fermentation

Bacterial fermentation of lignocellulose has been regarded as a sustainable approach to butyric acid production. However, the yield of butyric acid is hindered by the conversion efficiency of hydrolysate xylose. A mesophilic alkaline-tolerant strain designated as Clostridium butyricum B10 was isolated by xylose fermentation with acetic and butyric acids as the principal liquid products. To enhance butyric acid production, performance of the strain in batch fermentation was evaluated with various temperatures (20–47 °C), initial pH (5.0–10.0), and xylose concentration (6–20 g/L). The results showed that the optimal temperature, initial pH, and xylose concentration for butyric acid production were 37 °C, 9.0, and 8.00 g/L, respectively. Under the optimal condition, the yield and specific yield of butyric acid reached about 2.58 g/L and 0.36 g/g xylose, respectively, with 75.00% butyric acid in the total volatile fatty acids. As renewable energy, hydrogen was also collected from the xylose fermentation with a yield of about 73.86 mmol/L. The kinetics of growth and product formation indicated that the maximal cell growth rate (μ _m ) and the specific butyric acid yield were 0.1466 h^?1 and 3.6274 g/g cell (dry weight), respectively. The better performance in xylose fermentation showed C. butyricum B10 a potential application in efficient butyric acid production from lignocellulose.     

Optimization of citric acid production from a carrot juice-based medium by <Emphasis Type="Italic">Yarrowia lipolytica</Emphasis> using response surface methodology

In this study, diluted and fortified carrot juice was used for modelling and optimization of citric acid production by a new mutant strain, Yarrowia lipolytica K-168. Protein concentrate obtained from fine flour -a byproduct of semolina production- was used as a nitrogen source in the fermentation medium. Interactive effects of selected independent variables, initial total sugar concentration, initial pH, initial concentration of protein concentrate obtained from fine flour of semolina and temperature, on the growth and citric acid production of the yeast were investigated. An experimental design including 30 experiments was conducted by using the method of central composite design. Modelling the effects of these independent variables on maximum citric acid concentration, maximum citric acid production rate, citric acid yield, the ratio of maximum citric acid concentration to maximum isocitric acid concentration and specific growth rate were performed by response surface methodology. The variations of all of the responses with the independent variables were defined by a quadratic model. Numeric optimization was performed by using the desireability function. The conditions with 190.83 g/L initial sugar concentration, 5.90 initial pH, 0.07 g/L initial concentration of fine flour protein concentrate and 27.86 °C were determined as optimal conditions for citric acid production. The maximum citric acid concentration reached to 80.53 g/L in optimal conditions.     

耐乙酸粘红酵母合成油脂

乙酸是木质纤维素在水解过程中的主要副产物,高浓度的乙酸严重影响产油微生物的生长和油脂合成。本文研究了粘红酵母对乙酸的耐受性及其利用乙酸合成微生物油脂的能力。结果表明,在初始葡萄糖、木糖浓度分别为6 g/L和44 g/L的混合糖培养基中,乙酸浓度低于10 g/L时,不会对菌体生长产生抑制作用,油脂合成还得到了促进。当乙酸添加量为10 g/L时,生物量、油脂产量、油脂含量较对照组分别提高了21.5%、171.2%和121.6%。进一步研究表明,粘红酵母具备利用乙酸合成油脂的能力,当以乙酸为唯一碳源,浓度为25 g/L时,油脂产量达到3.20 g/L,油脂质量得率为13%。微生物油脂成分分析表明,粘红酵母以乙酸为底物制得的油脂可以作为制备生物柴油的油脂原料,其主要成分为棕榈酸、硬脂酸、油酸、亚油酸和亚麻酸,其中饱和脂肪酸和不饱和脂肪酸含量分别为40.9%和59.1%。由于粘红酵母具有利用乙酸合成微生物油脂的能力,在以木质纤维素水解液为原料生产微生物油脂的脱毒过程中,一定浓度的乙酸可以不必脱除。