Effects of acetate and nitrite addition on fraction of denitrifying phosphate-accumulating organisms and nutrient removal efficiency in anaerobic/aerobic/anoxic process

The effects of acetate and nitrite on the performance of sequencing batch reactors (SBRs) employing an anaerobic/aerobic/anoxic (AOA) process were investigated. Three types of SBR operations were used: sodium acetate addition at the start of anoxic condition for heterotrophic denitrification (Type 1); sodium acetate addition at the start of aerobic condition for anoxic phosphate removal by denitrifying phosphate-accumulating organisms (DNPAOs) (Type 2: conventional AOA process); and nitrite addition at the start of aerobic condition for inhibition of phosphate-accumulating organisms (PAOs) (Type 3). A track experiment shows that Type 2 led to the best performance of SBRs among the three types. An analysis by fluorescence in situ hybridization (FISH) revealed that nitrite addition decreased the ratio of PAOs with a decrease in phosphorus removal efficiency. The fraction of DNPAOs in Type 2 was the highest at 13%, indicating that Type 2 is suitable for the simultaneous nitrogen and phosphorus removal in the AOA process.     

Metabolic influence of lead on polyhydroxyalkanoates (PHA) production and phosphate uptake in activated sludge fed with glucose or acetic acid as carbon source

Sludge in a sequential batch reactor (SBR) system was used to investigate the effect of lead toxicity on metabolisms of polyphosphate accumulating organisms (PAOs) and glycogen accumulating organisms (GAOs) communities fed with acetic acid or glucose as their sole carbon source, respectively. Results showed that the effect of lead on substrate utilization of both PAOs and GAOs was insignificant. However, lead substantially inhibited both of phosphate release and uptake of PAOs. In high concentration of acetic acid trials, an abnormal aerobic phosphate release was observed instead of phosphate uptake and the release rate increased with increasing lead concentration. Results also showed that PAOs could normally synthesize polyhydroxybutyrate (PHB) in the anaerobic phase even though lead concentration was 40 mg L⁻¹. However, they could not aerobically utilize PHB normally in the presence of lead. On the other hand, GAOs could not normally metabolize polyhydroxyvalerate (PHV) in both the anaerobic and aerobic phases.     

Enhanced denitrifying phosphorous removal in a novel anaerobic/aerobic/anoxic (AOA) process with the diversion of internal carbon source

A novel anaerobic/aerobic/anoxic (AOA) process is proposed to realize denitrifying phosphorous removal in this study, and the characteristic of the AOA process is transferring part of the anaerobic mixed liquor to the post-anoxic zone for providing the carbon source needed for denitrification. The AOA process was operated for 3 months, and the average removal efficiencies of NH4+-N, TN and PO4(3-)-P were 93.0±3.1%, 70.3±2.9% and 87.3±11.8%, respectively. A mass balance analysis indicated that 0.49±0.02 g VSS(-1) d(-1) of PO4(3-)-P and 0.23±0.04 g VSS(-1) d(-1) of NO3--N were simultaneously removed in the anoxic zone, and it is speculated that denitrifying phosphorous removal occurred in the AOA process. Furthermore, 0.24±0.06 g VSS(-1) d(-1) of TN was removed in the aerobic zone via simultaneous nitrification and denitrification (SND). The results demonstrate that the multi-zone structure of the AOA process favors the enhancement of denitrifying phosphorous removal and SND for municipal wastewater treatment.     

Verification of enhanced phosphate removal capability in pure cultures of<Emphasis Type="Italic">Acinetobacter calcoaceticus</Emphasis> under anaerobic/aerobic conditions in an SBR

Laboratory experiments were conducted using pure cultures ofAcinetobacter under anaerobic/aerobic cyclic conditions to explain the release and uptake of soluble phosphate in an activated sludge process showing enhanced biological phosphate removal (EBPR). Under anaerobic/aerobic cyclic conditions in a Sequencing Batch Reactor (SBR), COD uptake concurrent with soluble phosphate release byAcinetobacter was not significant during the anaerobic periods, indicating that EBPR would not be established in pure cultures. However,Acinetobacter cells accumulated higher phosphate content (5.2%) in SBR than that obtained (4.3%) from batch experiments. These results suggest thatAcinetobacter sp. may not follow the proposed pattern of behavior of poly-P bacteria in EBPR activated sludge plants.     

Decolorization of azo-reactive dye by polyphosphate- and glycogen-accumulating organisms in an anaerobic-aerobic sequencing batch reactor

An anaerobic-aerobic sequencing batch reactor with a sludge age of 8 days and anaerobic + aerobic + settling times of 18 + 5 + 1 h, was used to decolorize an azo-reactive dye wastewater. The nutrient broth (NB) and sodium acetate (SA) solution at 500 + 0, 350 + 150, 250 + 250 and 0 + 500 mg/l as COD was fed to the system to promote the polyphosphate-accumulating organisms (PAOs), while only glucose (500 mg/l COD) was used as a glycogen-accumulating organisms (GAOs) promoting substrate. The decolorization capability of the process was about 73-77 and 59-64% in terms of ADMI for the systems which the PAOs and GAOs proliferated, respectively. The color reduction was mainly achieved within the first 2 h of the anaerobic stage.     

Experimental evaluation of decrease in the activities of polyphosphate/glycogen‐accumulating organisms due to cell death and activity decay in activated sludge

Decrease in bacterial activity (biomass decay) in activated sludge can result from cell death (reduction in the amount of active bacteria) and activity decay (reduction in the specific activity of active bacteria). The goal of this study was to experimentally differentiate between cell death and activity decay as the cause of decrease in bacterial activity. By means of measuring maximal anaerobic phosphate release rates, verifying membrane integrity by live/dead staining and verifying presence of 16S rRNA with fluorescence in situ hybridization (FISH), the decay rates and death rates of polyphosphate‐accumulating organisms (PAOs) in a biological nutrient removal (BNR) system and a laboratory phosphate removing sequencing batch reactor (SBR) system were determined, respectively, under famine conditions. In addition, the decay rate and death rate of glycogen‐accumulating organisms (GAOs) in a SBR system with an enrichment culture of GAOs were also measured under famine conditions. Hereto the maximal anaerobic volatile fatty acid uptake rates, live/dead staining, and FISH were used. The experiments revealed that in the BNR and enriched PAO‐SBR systems, activity decay contributed 58% and 80% to the decreased activities of PAOs, and that cell death was responsible for 42% and 20% of decreases in their respective activities. In the enriched GAOs system, activity decay constituted a proportion of 74% of the decreased activity of GAOs, and cell death only accounted for 26% of the decrease of their activity. Biotechnol. Bioeng. 2010; 106: 399–407. © 2010 Wiley Periodicals, Inc.     

Model-based analysis of anaerobic acetate uptake by a mixed culture of polyphosphate-accumulating and glycogen-accumulating organisms

An increasing number of studies shows that the glycogen-accumulating organisms (GAOs) can survive and may indeed proliferate under the alternating anaerobic/aerobic conditions found in EBPR systems, thus forming a strong competitor of the polyphosphate-accumulating organisms (PAOs). Understanding their behaviors in a mixed PAO and GAO culture under various operational conditions is essential for developing operating strategies that disadvantage the growth of this group of unwanted organisms. A model-based data analysis method is developed in this paper for the study of the anaerobic PAO and GAO activities in a mixed PAO and GAO culture. The method primarily makes use of the hydrogen ion production rate and the carbon dioxide transfer rate resulting from the acetate uptake processes by PAOs and GAOs, measured with a recently developed titration and off-gas analysis (TOGA) sensor. The method is demonstrated using the data from a laboratory-scale sequencing batch reactor (SBR) operated under alternating anaerobic and aerobic conditions. The data analysis using the proposed method strongly indicates a coexistence of PAOs and GAOs in the system, which was independently confirmed by fluorescent in situ hybridization (FISH) measurement. The model-based analysis also allowed the identification of the respective acetate uptake rates by PAOs and GAOs, along with a number of kinetic and stoichiometric parameters involved in the PAO and GAO models. The excellent fit between the model predictions and the experimental data not involved in parameter identification shows that the parameter values found are reliable and accurate. It also demonstrates that the current anaerobic PAO and GAO models are able to accurately characterize the PAO/GAO mixed culture obtained in this study. This is of major importance as no pure culture of either PAOs or GAOs has been reported to date, and hence the current PAO and GAO models were developed for the interpretation of experimental results of mixed cultures. The proposed method is readily applicable for detailed investigations of the competition between PAOs and GAOs in enriched cultures. However, the fermentation of organic substrates carried out by ordinary heterotrophs needs to be accounted for when the method is applied to the study of PAO and GAO competition in full-scale sludges.     

An innovative membrane bioreactor (MBR) system for simultaneous nitrogen and phosphorus removal

Membrane filtration was integrated with a post-denitrification process to form an innovative membrane bioreactor (MBR) system for effective organic degradation and nutrient (N and P) removal. The system comprised of an aerobic tank, an anoxic tank, an intermediate sedimentation tank, and a membrane filtration tank. The sedimentation tank functioned not only as a rough settler for sludge–water separation before membrane filtration but also as an anaerobic chamber for P release. While half of the influent flowed into the aerobic tank, the other half was fed into the anoxic tank to favor the proliferation of phosphorus accumulating organisms (PAOs). The experiment was conducted continuously for about 430 days. With a short overall treatment time of less than 10 h for municipal wastewater, the MBR-based process could achieve the total organic carbon, total nitrogen, and total phosphorus removals of around 94%, 85%, and 87%, respectively. The growth and activity of PAOs in the MBR system were evidenced by the significant P release in the anaerobic chamber followed by the luxury P uptake in the membrane tank. With the DAPI and PAO_mix probe staining, the increases of PAOs and polyhydroxybutyrate (PHB) in sludge during the experiment were well observed under the fluorescent microscope.     

Anaerobic metabolism of propionate by polyphosphate-accumulating organisms in enhanced biological phosphorus removal systems

Propionate, a carbon substrate abundant in many prefermenters, has been shown in several previous studies to be a more favorable substrate than acetate for enhanced biological phosphorus removal (EBPR). The anaerobic metabolism of propionate by polyphosphate accumulating organisms (PAOs) is studied in this paper. A metabolic model is proposed to characterize the anaerobic biochemical transformations of propionate uptake by PAOs. The model is demonstrated to predict very well the experimental data from a PAO culture enriched in a laboratory-scale reactor with propionate as the sole carbon source. Quantitative fluorescence in-situ hybridization (FISH) analysis shows that Candidatus Accumulibacter phosphatis, the only identified PAO to date, constitute 63% of the bacterial population in this culture. Unlike the anaerobic metabolism of acetate by PAOs, which induces mainly poly-beta-hydroxybutyrate (PHB) production, the major fractions of poly-beta-hydroxyalkanoate (PHA) produced with propionate as the carbon source are poly-beta-hydroxyvalerate (PHV) and poly-beta-hydroxy-2-methylvalerate (PH2MV). PHA formation correlates very well with a selective (or nonrandom) condensation of acetyl-CoA and propionyl-CoA molecules. The maximum specific propionate uptake rate by PAOs found in this study is 0.18 C-mol/C-mol-biomass . h, which is very similar to the maximum specific acetate uptake rate reported in literature. The energy required for transporting 1 carbon-mole of propionate across the PAO cell membrane is also determined to be similar to the transportation of 1 carbon-mole of acetate. Furthermore, the experimental results suggest that PAOs possess a similar preference toward acetate and propionate uptake on a carbon-mole basis.     

Development and characteristics of phosphorus-accumulating microbial granules in sequencing batch reactors

Phosphorus (P)-accumulating microbial granules were developed at different substrate P/chemical oxygen demand (COD) ratios in the range of 1/100 to 10/100 by weight in sequencing batch reactors. The soluble COD and PO4-P profiles showed that the granules had typical P-accumulating characteristics, with concomitant uptake of soluble organic carbon and the release of phosphate in the anaerobic stage, followed by rapid phosphate uptake in the aerobic stage. The size of P-accumulating granules exhibited a decreasing trend with the increase in substrate P/COD ratio, while the structure of the granules became more compact and denser as the substrate P/COD ratio increased. The P uptake by granules fell within the range of 1.9% to 9.3% by weight, which is comparable with uptake obtained in conventional enhanced biological phosphorus removal (EBPR) processes. It was further found that low aerobic respirometric activity of granules in terms of specific oxygen utilization rate favors P uptake by granules. The results presented would be useful for the further development of a novel granule-based EBPR technology.     

Inducing mechanism of biological phosphorus removal driven by the aerobic/extended-idle regime

Recently, it was found that excess phosphorus (Pi) removal could be achieved in activated sludge with an aerobic/extended‐idle (AEI) process. In this study, batch tests were performed to further reveal the inducing mechanism of Pi removal involved in the AEI process. Unlike the classical anaerobic/aerobic process where an anaerobic Pi release along with a significant polyhydroxyalkanoate (PHA) accumulation drives polyphosphate (poly‐P) accumulating organisms (PAOs) to over‐store Pi as poly‐P, an idle Pi release accompanied by a low‐idle PHA production, which is usually considered to be detrimental for biological Pi removal, was observed to induce some cells to effectively uptake Pi in excess of metabolic requirement in the AEI process. With the increase of idle Pi release, Pi removal efficiency linearly increased. The results also showed that a long idle period with a low level of intracellular glycogen could significantly increase Pi release contents, thus remarkably enhancing Pi removal performances. Fluorescence in situ hybridization analysis further revealed that activated sludge in the AEI process contained 37.6% of Accumulibacter (PAOs) and 28.2% of Competibacter and Defluviicoccus‐related organisms (glycogen accumulating organisms). This study revealed an actually existent, yet previously unrecognized, inducing mechanism of poly‐P accumulation, and this mechanism behind the AEI regime may provide a scientific basis for the development of an alternative strategy for Pi removal from wastewaters. Biotechnol. Bioeng. 2012; 109: 2798–2807. © 2012 Wiley Periodicals, Inc.     

Aerobic phosphorus release linked to acetate uptake in bio-P sludge: process modeling using oxygen uptake rate

The main processes involved in enhanced biological phosphorus removal (EBPR) under anaerobic and subsequently aerobic conditions are widely described in the literature. Polyphosphate accumulating organisms (PAO) are the organisms responsible for this process. However, the mechanisms of PAO are not fully established yet under conditions that differ from the classical anaerobic/aerobic conditions. In this work, we made a comparison between the behavior of PAO under classical EBPR conditions and its behavior when consuming substrate under only aerobic conditions. In addition, oxygen uptake rate (OUR) was measured in the set of experiments under aerobic conditions to improve the characterization of the process. A kinetic and stoichiometric model based on Activated Sludge Model No.2 (ASM2) and including glycogen economy (AnOx model), calibrated for classical anaerobic/aerobic conditions, was not able to describe the experimental data since it underestimated the acetate consumption, the PHB storage, and the OUR. Two different hypotheses for describing the experimental measurements were proposed and modeled. Both hypotheses considered that PAO, under aerobic conditions, uptake acetate coupled to PHB storage, glycogen degradation, and phosphorus release as in anaerobic conditions. Moreover, the first hypothesis (PAO-hypothesis) considered that PAO were able to store acetate as PHB linked to oxygen consumption and the second one (OHO hypothesis) considered that this storage was due to ordinary heterotrophic organisms (OHO). Both hypotheses were evaluated by simulation extending the AnOx model with additional equations. The main differences observed were the predictions for PHB degradation during the famine phase and the OUR profile during both feast and famine phases. The OHO hypothesis described the experimental profiles more accurately than the PAO hypothesis.     

Identification and comparison of aerobic and denitrifying polyphosphate-accumulating organisms

Two laboratory-scale sequencing batch reactors (SBRs) were operated for enhanced biological phosphorus removal (EBPR) in alternating anaerobic-aerobic or alternating anaerobic-anoxic modes, respectively. Polyphosphate-accumulating organisms (PAOs) were enriched in the anaerobic-aerobic SBR and denitrifying PAOs (DPAOs) were enriched in the anaerobic-aerobic SBR. Fluorescence in situ hybridization (FISH) demonstrated that the well-known PAO, "Candidatus Accumulibacter phosphatis" was abundant in both SBRs, and post-FISH chemical staining with 4,6-diamidino-2-phenylindol (DAPI) confirmed that they accumulated polyphosphate. When the anaerobic-anoxic SBR enriched for DPAOs was converted to anaerobic-aerobic operation, aerobic uptake of phosphorus by the resident microbial community occurred immediately. However, when the anaerobic-aerobic SBR enriched for PAOs was exposed to one cycle with anoxic rather than aerobic conditions, a 5-h lag period elapsed before phosphorus uptake proceeded. This anoxic phosphorus-uptake lag phase was not observed in the subsequent anaerobic-aerobic cycle. These results demonstrate that the PAOs that dominated the anaerobic-aerobic SBR biomass were the same organisms as the DPAOs enriched under anaerobic-anoxic conditions.     

Effects of different carbon supplements on phosphorus removal in low C/P ratio industrial wastewater

This study focuses on the effects of different carbon supplements on biological phosphorus removal in the optonics and semiconductor industrial wastewater treatment. Experimental results demonstrate that the addition of a carbon source (glucose, acetate, and digester supernatant) improved phosphorus removal effectively. When the COD/P ratios were controlled in the range of 18-20 (using glucose and supernatant as supplement), the acclimated sludge showed more than 98% removal of phosphorus. In addition, different organic carbons induce dissimilar behavior in anaerobic release and aerobic uptake of phosphorus. The glucose supplement induces significant phosphorus release in anaerobic phase and then an increased phosphorus uptake in aerobic phase. The released phosphorus descended in anaerobic phase when acetate and supernatant were added. There was a good linear relationship of first order reaction between initial COD concentration and specific substrate utilization rate in anaerobic phase.     

Effect of basic operating parameters on biological phosphorus removal in a continuous-flow anaerobic–anoxic activated sludge system

A continuous-flow anaerobic–anoxic (A2) activated sludge system was operated for efficient enhanced biological phosphorus removal (EBPR). Because of the system configuration with no aeration zones, phosphorus (P) uptake takes place solely under anoxic conditions with simultaneous denitrification. Basic operating conditions, namely biomass concentration, influent carbon to phosphorus ratio and anaerobic retention time were chosen as variables in order to assess their impact on the system performance. The experimental results indicated that maintenance of biomass concentration above 2,500 mg MLVSS/L resulted in the complete phosphate removal from the influent (i.e. 15 mg PO₄ ³⁻-P/L) for a mean hydraulic residence time (HRT) of 15 h. Additionally, by increasing the influent COD/P ratio from 10 to 20 g/g, the system P removal efficiency was improved although the experimental results indicated a possible enhancement of the competition between phosphorus accumulating organisms (PAOs) and other microbial populations without phosphorus uptake ability. Moreover, because of the use of acetate (i.e. easily biodegradable substrate) as the sole carbon source in the system feed, application of anaerobic retention times greater than 2 h resulted in no significant release of additional P in the anaerobic zone and no further amelioration of the system P removal efficiency. The application of anoxic P removal resulted in more than 50% reduction of the organic carbon necessitated for nitrogen and phosphorus removal when compared to a conventional EBPR system incorporating aerobic phosphorus removal.     

Enhanced wastewater treatment efficiency through microbially catalyzed oxidation and reduction: synergistic effect of biocathode microenvironment

Microbially catalyzed treatment of wastewater was evaluated in both the anode and cathode chambers in dual chambered microbial fuel cell (MFC) under varying biocathode microenvironment. MFC operation with aerobic biocathode showed significant increment in both TDS (cathode, 90.2±1%; anode, 39.7±0.5%) and substrate (cathode, 98.07±0.06%; anode, 96.2±0.3%) removal compared to anaerobic biocathode and abiotic cathode operations (COD, 80.25±0.3%; TDS, 30.5±1.2%). Microbially catalyzed reduction of protons and electrons at cathode will be higher during aerobic biocathode operation which leads to gradual substrate removal resulting in stable bio-potential for longer periods facilitating salts removal. Bio-electro catalytic behavior showed higher exchange current density during aerobic biocathode operation resulting in induced electrochemical oxidation which supports the enhanced treatment. Anaerobic biocathode operation depicted relatively less TDS removal (anode, 16.35%; cathode, 16.04%) in both the chambers in spite of good substrate degradation (anode, 84%; cathode, 87.39%). Both the chambers during anaerobic biocathode operation competed as electron donors resulting in negligible bio-potential development.     

Fully coupled activated sludge model (FCASM): Model development

A sub-microscopic mechanism model named Fully Coupled Activated Sludge Model (FCASM) about biological nutrient removal in the wastewater treatment process was developed in the present study. The functional organisms existing simultaneously in the activated sludge system were separated into eight groups, including aerobic heterotrophic organisms, nitrite reducing organisms, nitrate reducing organisms, ammonium oxidizing autotrophs, nitrite oxidizing autotrophs, non-denitrifying phosphorus-accumulating organisms (PAOs), denitrifying phosphorus-accumulating bacteria (DPB), and glycogen-accumulating organisms (GAOs). In FCASM, the interaction relationships of the eight functional microorganisms were taken fully into account. FCASM could model biological nitrogen removal via nitrite by splitting nitrification process and denitrification process into two-step reactions, and the autotrophs and denitrifying organisms were divided into two groups, respectively. What’s important, FCASM included the anaerobic maintenance processes of sequential utilization of polyphosphate followed by glycogen for PAOs and DPB and glycolysis of the intracellular stored glycogen for GAOs.     

Metabolic model for glycogen-accumulating organisms in anaerobic/aerobic activated sludge systems

Glycogen-accumulating organisms (GAO) have the potential to directly compete with polyphosphate-accumulating organisms (PAO) in EBPR systems as both are able to take up VFA anaerobically and grow on the intracellular storage products aerobically. Under anaerobic conditions GAO hydrolyse glycogen to gain energy and reducing equivalents to take up VFA and to synthesise polyhydroxyalkanoate (PHA). In the subsequent aerobic stage, PHA is being oxidised to gain energy for glycogen replenishment (from PHA) and for cell growth. This article describes a complete anaerobic and aerobic model for GAO based on the understanding of their metabolic pathways. The anaerobic model has been developed and reported previously, while the aerobic metabolic model was developed in this study. It is based on the assumption that acetyl-CoA and propionyl-CoA go through the catabolic and anabolic processes independently. Experimental validation shows that the integrated model can predict the anaerobic and aerobic results very well. It was found in this study that at pH 7 the maximum acetate uptake rate of GAO was slower than that reported for PAO in the anaerobic stage. On the other hand, the net biomass production per C-mol acetate added is about 9% higher for GAO than for PAO. This would indicate that PAO and GAO each have certain competitive advantages during different parts of the anaerobic/aerobic process cycle.     

Anaerobic treatment of complex chemical wastewater in a sequencing batch biofilm reactor: process optimization and evaluation of factor interactions using the Taguchi dynamic DOE methodology

The Taguchi robust experimental design (DOE) methodology has been applied on a dynamic anaerobic process treating complex wastewater by an anaerobic sequencing batch biofilm reactor (AnSBBR). For optimizing the process as well as to evaluate the influence of different factors on the process, the uncontrollable (noise) factors have been considered. The Taguchi methodology adopting dynamic approach is the first of its kind for studying anaerobic process evaluation and process optimization. The designed experimental methodology consisted of four phases--planning, conducting, analysis, and validation connected sequence-wise to achieve the overall optimization. In the experimental design, five controllable factors, i.e., organic loading rate (OLR), inlet pH, biodegradability (BOD/COD ratio), temperature, and sulfate concentration, along with the two uncontrollable (noise) factors, volatile fatty acids (VFA) and alkalinity at two levels were considered for optimization of the anae robic system. Thirty-two anaerobic experiments were conducted with a different combination of factors and the results obtained in terms of substrate degradation rates were processed in Qualitek-4 software to study the main effect of individual factors, interaction between the individual factors, and signal-to-noise (S/N) ratio analysis. Attempts were also made to achieve optimum conditions. Studies on the influence of individual factors on process performance revealed the intensive effect of OLR. In multiple factor interaction studies, biodegradability with other factors, such as temperature, pH, and sulfate have shown maximum influence over the process performance. The optimum conditions for the efficient performance of the anaerobic system in treating complex wastewater by considering dynamic (noise) factors obtained are higher organic loading rate of 3.5 Kg COD/m3 day, neutral pH with high biodegradability (BOD/COD ratio of 0.5), along with mesophilic temperature range (40 degrees C), and low sulfate concentration (700 mg/L). The optimization resulted in enhanced anaerobic performance (56.7%) from a substrate degradation rate (SDR) of 1.99 to 3.13 Kg COD/m3 day. Considering the obtained optimum factors, further validation experiments were carried out, which showed enhanced process performance (3.04 Kg COD/m3-day from 1.99 Kg COD/m3 day) accounting for 52.13% improvement with the optimized process conditions. The proposed method facilitated a systematic mathematical approach to understand the complex multi-species manifested anaerobic process treating complex chemical wastewater by considering the uncontrollable factors.     

Comparison of acetate and propionate uptake by polyphosphate accumulating organisms and glycogen accumulating organisms

Enhanced biological phosphorus removal (EBPR) performance is directly affected by the competition between polyphosphate accumulating organisms (PAOs) and glycogen accumulating organisms (GAOs). This study investigates the effects of carbon source on PAO and GAO metabolism. Enriched PAO and GAO cultures were tested with the two most commonly found volatile fatty acids (VFAs) in wastewater systems, acetate and propionate. Four sequencing batch reactors (SBRs) were operated under similar conditions and influent compositions with either acetate or propionate as the sole carbon source. The stimulus for selection of the PAO and GAO phenotypes was provided only through variation of the phosphorus concentration in the feed. The abundance of PAOs and GAOs was quantified using fluorescence in situ hybridisation (FISH). In the acetate fed PAO and GAO reactors, "Candidatus Accumulibacter phosphatis" (a known PAO) and "Candidatus Competibacter phosphatis" (a known GAO) were present in abundance. A novel GAO, likely belonging to the group of Alphaproteobacteria, was found to dominate the propionate fed GAO reactor. The results clearly show that there are some very distinctive differences between PAOs and GAOs in their ability to take up acetate and propionate. PAOs enriched with acetate as the sole carbon source were immediately able to take up propionate, likely at a similar rate as acetate. However, an enrichment of GAOs with acetate as the sole carbon source took up propionate at a much slower rate (only about 5% of the rate of acetate uptake on a COD basis) during a short-term switch in carbon source. A GAO enrichment with propionate as the sole carbon source took up acetate at a rate that was less than half of the propionate uptake rate on a COD basis. These results, along with literature reports showing that PAOs fed with propionate (also dominated by Accumulibacter) can immediately switch to acetate, suggesting that PAOs are more adaptable to changes in carbon source as compared to GAOs. This study suggests that the PAO and GAO competition could be influenced in favour of PAOs through the provision of propionate in the feed or even by regularly switching the dominant VFA species in the wastewater. Further study is necessary in order to provide greater support for these hypotheses.