A general kinetic model for biological nutrient removal activated sludge systems: model evaluation

Hu et al. (2007) presented a general kinetic model for biological nutrient removal (BNR) activated sludge (AS) systems in general, but for external nitrification (EN) BNRAS (ENBNRAS) systems in particular. In this article, this model is evaluated against a large number of experimental data sets. In this evaluation, the model is first used to simulate a wide variety of conventional internal nitrification (IN) BNRAS systems to evaluate its predictions and also evaluate the model parameters suggested by Hu et al. (2007), and to calibrate those constants for which values are not available in the literature. Simulation results indicate that the model, with appropriately calibrated parameters, is capable of predicting COD removal, nitrification and denitrification and two types of biological excess phosphorus removal (BEPR), namely aerobic and anoxic/aerobic P uptake BEPR. The model is then used to simulate the ENBNRAS systems to evaluate its capacity of simulating the behaviour of this system. Simulation results show that the model is capable of simulating the behaviour of the ENBNRAS systems, including COD, nitrification, denitrification and BEPR, particularly anoxic P uptake BEPR, with the values of kinetic and stoichiometric parameters obtained in modelling conventional BNRAS systems, except for micro(NIT), K(MP), eta(PAO) and eta(H) which required calibration.     

Assessment of a bioaugmentation strategy with polyphosphate accumulating organisms in a nitrification/denitrification sequencing batch reactor

Different alternative configurations and strategies for the simultaneous biological removal of organic matter and nutrients (N and P) in wastewater have been proposed in the literature. This work demonstrates a new successful strategy to bring in enhanced biological phosphorus removal (EBPR) to a conventional nitrification/denitrification system by means of bioaugmentation with an enriched culture of phosphorus accumulating organisms (PAO). This strategy was tested in a sequencing batch reactor (SBR), where an 8 h configuration with 3 h anoxic, 4.5 h aerobic and 25 min of settling confirmed that nitrification, denitrification and PAO activity could be maintained for a minimum of 60 days of operation after the bioaugmentation step. The successful bioaugmentation strategy opens new possibilities for retrofitting full-scale WWTP originally designed for only nitrification/denitrification. These systems could remove P simultaneously to COD and N if they were bioaugmented with waste purge of an anaerobic/aerobic SBR operated in parallel treating part of the influent wastewater.     

Simultaneous nitrification, denitrification, and phosphorus removal from nutrient-rich industrial wastewater using granular sludge

The biological removal of nitrogen and phosphorus from nutrient-rich abattoir wastewater using granular sludge has been investigated. A lab-scale sequencing batch reactor, seeded with granular sludge developed using synthetic wastewater, was operated for 13 months under alternating anaerobic and aerobic conditions. It is demonstrated that the granules could be sustained and indeed further developed with the use of abattoir wastewater. The organic, nitrogen, and phosphorus loading rates applied were 2.7 gCOD L(-1) day(-1), 0.43 gN L(-1) day(-1), and 0.06 gP L(-1) day(-1), respectively. The removal efficiency of soluble COD, soluble nitrogen and soluble phosphorus were 85%, 93%, and 89%, respectively. However, the high suspended solids in the effluent limited the overall removal efficiency to 68%, 86%, and 74% for total COD, TN, and TP, respectively. This good nutrient removal was achieved through the process known as simultaneous nitrification, denitrification, and phosphorus removal, likely facilitated by the presence of large anoxic zones in the center of the granules. The removal of nitrogen was likely via nitrite optimizing the use of the limited COD available in the wastewater. Accumulibacter spp. were found to be responsible for most of the denitrification, further reducing the COD requirement for nitrogen and phosphorus removal. Mineral precipitation was evaluated and was not found to significantly contribute to the overall nutrient removal. It is also shown that the minimum HRT in a granular sludge system is not governed by the sludge settleability, as is the case with floccular sludge systems, but likely by the limitations associated with the transfer of substrates in granules.     

Microbial distribution of Accumulibacter spp. and Competibacter spp. in aerobic granules from a lab-scale biological nutrient removal system

Granular sludge for simultaneous nitrification, denitrification and phosphorus removal (SNDPR) was generated and studied in a lab-scale sequencing batch reactor (SBR). The SBR was monitored for 450 days during which the biomass was transformed from flocs to granules, which persisted for the last 130 days of operation. Short sludge settling time was employed to successfully generate the granules, with the 10th and 90th percentiles of diameter being 0.7 and 1.6 mm respectively. Good phosphorus removal and nitrification occurred throughout the SBR operation but only when granules were generated were denitrification and full nutrient removal complete. Fluorescence in situ hybridization and oxygen microsensors were used to study the granules at a microscale. Accumulibacter spp. (a polyphosphate-accumulating organism, PAO) and Competibacter spp. (a glycogen non-polyphosphate-accumulating organism, GAO) were the most abundant microbial community members (together 74% of all Bacteria ) and both are capable of denitrification. In the aerobic period of the SBR operation, the oxygen penetrated 250 μm into the granules leaving large anoxic zones in the centre part where denitrification can occur. In granules > 500 μm in diameter, Accumulibacter spp. was dominant in the outermost 200 μm region of the granule while Competibacter spp. dominated in the granule central zone. The stratification of these two populations between the outer aerobic and inner anoxic part of the granule was highly significant ( P  < 0.003). We concluded that the GAO Competibacter spp., and not the PAO Accumulibacter spp., was responsible for denitrification in this SBR. This is undesirable for SNDPR as savings in carbon demand cannot be fulfilled with phosphorus removal and denitrification being achieved by different groups of bacteria.     

A comparative study of methanol as a supplementary carbon source for enhancing denitrification in primary and secondary anoxic zones

A comparative study on the use of methanol as a supplementary carbon source to enhance denitrification in primary and secondary anoxic zones is reported. Three lab-scale sequencing batch reactors (SBR) were operated to achieve nitrogen and carbon removal from domestic wastewater. Methanol was added to the primary anoxic period of the first SBR, and to the secondary anoxic period of the second SBR. No methanol was added to the third SBR, which served as a control. The extent of improvement on the denitrification performance was found to be dependent on the reactor configuration. Addition to the secondary anoxic period is more effective when very low effluent nitrate levels are to be achieved and hence requires a relatively large amount of methanol. Adding a small amount of methanol to the secondary anoxic period may cause nitrite accumulation, which does not improve overall nitrogen removal. In the latter case, methanol should be added to the primary anoxic period. The addition of methanol can also improve biological phosphorus removal by creating anaerobic conditions and increasing the availability of organic carbon in wastewater for polyphosphate accumulating organisms. This potentially provides a cost-effective approach to phosphorus removal from wastewater with a low carbon content. New fluorescence in situ hybridisation (FISH) probes targeting methanol-utilising denitrifiers were designed using stable isotope probing. Microbial structure analysis of the sludges using the new and existing FISH probes clearly showed that the addition of methanol stimulated the growth of specific methanol-utilizing denitrifiers, which improved the capability of sludge to use methanol and ethanol for denitrification, but reduced its capability to use wastewater COD for denitrification. Unlike acetate, long-term application of methanol has no negative impact on the settling properties of the sludge.     

A general kinetic model for biological nutrient removal activated sludge systems: model development

In this article, a kinetic model is developed and presented for biological nutrient removal (BNR) activated sludge (BNRAS) systems in general, but for external nitrification (EN) BNRAS (ENBNRAS) systems in particular. The model is based on the UCTPHO model, but includes some significant modifications, such as anoxic P uptake and associated denitrification by phosphorus accumulating organisms (PAOs). Some key features of the model are described and discussed before the model is presented. Model evaluation will be addressed in another article (Hu et al., 2007).     

Simultaneous nitrification,denitrification, and phosphorus removal in a lab-scale sequencing batch reactor

Simultaneous nitrification and denitrification (SND) via the nitrite pathway and anaerobic-anoxic-enhanced biological phosphorus removal (EBPR) are two processes that can significantly reduce the energy and COD demand for nitrogen and phosphorus removal. The combination of these two processes has the potential of achieving simultaneous nitrogen and phosphorus removal with a minimal requirement for COD. A lab-scale sequencing batch reactor (SBR) was operated in alternating anaerobic-aerobic mode with a low dissolved oxygen (DO) concentration (0.5 mg/L) during the aerobic period, and was demonstrated to accomplish nitrification, denitrification, and phosphorus removal. Under anaerobic conditions, COD was taken up and converted to polyhydroxyalkanoates (PHAs), accompanied by phosphorus release. In the subsequent aerobic stage, PHA was oxidized and phosphorus was taken up to <0.5 mg/L by the end of the cycle. Ammonia was also oxidized during the aerobic period, but without accumulation of nitrite or nitrate in the system, indicating the occurrence of simultaneous nitrification and denitrification. However, off-gas analysis showed that the final denitrification product was mainly nitrous oxide (N(2)O), not N(2). Further experimental results demonstrated that nitrogen removal was via nitrite, not nitrate. These experiments also showed that denitrifying glycogen-accumulating organisms (DGAOs), rather than denitrifying polyphosphate-accumulating organisms (DPAOs), were responsible for the denitrification activity.     

Preliminary study of a suspended growth predenitrification system

A laboratory study has been conducted to obtained preliminary process information of a suspended growth Predenitrification (SGPDN)system. System performance was evaluated, in terms of chemical oxygen demand (COD) removal, NH(3)-N removal, system biomass yield and inventory, and effluent qualities, at different solids retention times (SRTs) and recycle ratios. Chemical oxygen demand removal in an SGPDN system occurs mainly in the anoxic reactor, which accounts for 94% of total COD removal. The overall COD removal rate is independent of recycle ratio (ranging from 2-5) used in this study; however, effluent COD increase with increasing recycle ratio. The observed anoxic and aerobic COD removal rates decrease with increasing SRT. The NH(3)-N removal in an SGPDN system is induced by two mechanisms: assimilatory NH(3)-N requirement for biomass production in the anoxic reactor and nitrification in the aerobic reactor. The observed anoxic NH(3)-N removal rate relates directly to the anoxic COD removal rate and agrees fairly well with the assimilatory NH(3)-N requirement theoretically predicted. The overall NH(3)-N removal rate is independent of SRTs and recycle ratios used in this study. Biomass yield in an SGPDN system occurs mainly in the anoxic reactor. However, uniform distribution of biomass throughout the entire system is obtained because of the high recycle rate used. The observed biomass yield (Y(O)) decreases with increasing STR. Tertiary treatment efficiency can be achieved in an SGPDN system. More than 90% reduction in feed COD., feed NH(3)-N, and NO(2) + NO(3)-N is obtained at all SRTs and recycle ratios used in this study. Higher MLVSS loading rates can be applied to a final clarifier without impairing its separation efficiency because of the excellent settleability of the Predenitrification activated sludge.     

Challenges for simultaneous nitrification, denitrification, and phosphorus removal in microbial aggregates: mass transfer limitation and nitrous oxide production

The microbial community composition and activity was investigated in aggregates from a lab-scale bioreactor, in which nitrification, denitrification and phosphorus removal occurred simultaneously. The biomass was highly enriched for polyphosphate accumulating organisms facilitating complete removal of phosphorus from the bulk liquid; however, some inorganic nitrogen still remained at the end of the reactor cycle. This was ascribed to incomplete coupling of nitrification and denitrification causing NO(3)(-) accumulation. After 2 h of aeration, denitrification was dependent on the activity of nitrifying bacteria facilitating the formation of anoxic zones in the aggregates; hence, denitrification could not occur without simultaneous nitrification towards the end of the reactor cycle. Nitrous oxide was identified as a product of denitrification, when based on stored PHA as carbon source. This observation is of critical importance to the outlook of applying PHA-driven denitrification in activated sludge processes.     

The influence of anaerobic pretreatment on the nitrogen removal from biosynthetic pharmaceutical wastewaters

The C:N ratio of the pharmaceutical wastewaters is usually suitable for a combination of the anaerobic pretreatment with the high COD removal and aerobic posttreatment with the efficient biological N removal. This kind of anaerobic-aerobic process was tested in semipilot scale by using a UASB reactor and an activated sludge system with a predenitrification (total volume 100 1). It was found that at a total HRT of 2.3 days an average of 97.5% of COD and 73.5% of total N was removed. The UASB reactor was operated at 30°C with a volumetric loading rate of 8.7 kg.m^-3.d^-1, the efficiency of COD removal was 92.2%. The processes, which take part in the biological removal of nitrogen, especially the nitrification, were running with lower rates than usually observed in aerobic treatment systems.Abbreviations AAO anaerobic anoxic oxic configuration - AOO anaerobic oxic oxic configuration - B _V volumetric organic loading rate (kg COD.m^-3. d^-1) - dB _x specific COD removal rate (mg COD. g^-1 VSS. d^-1) - DNR denitrification rate (mg N–NO₃. g^-1 VSS. h^-1) - E_COD efficiency of COD removal (%) - HRT hydraulic retention time (d) - NR nitrification rate (mg N–NO₃. g^-1 VSS. h^-1) - R recirculation ratio (%) - SBP specific biogas production (m³.kg^-1 removed COD) - SRT solids retention time; sludge age (d) - SS suspended solids (g.1^-1) - UASB upflow anaerobic sludge blanket reactor - VSS volatile suspended solids (g.1^-1)     

Comparison of biological removal via nitrite with real-time control using aerobic granular sludge and flocculent activated sludge

The process of nitrification–denitrification via nitrite for nitrogen removal under real-time control mode was tested in two laboratory-scale sequencing batch reactors (SBRs) with flocculent activated sludge (R1) and aerobic granular sludge (R2) to compare operational performance and real-time control strategies. The results showed that the average ammonia nitrogen, total inorganic nitrogen (TIN), and chemical oxygen demand (COD) removal during aeration phase were 97.6%, 57.0%, and 90.1% in R2 compared with 98.6%, 48.7%, and 88.1% in R1. The TIN removed in both SBRs was partially due to the presence of simultaneous nitrification–denitrification via nitrite, especially in R2. The specific nitrification and denitrification rates in R2 were 0.0416 mgNH₄⁺–N/gSS-min and 0.1889 mgNO_X⁻–N/gSS-min, which were 1.48 times and 1.35 times that of R1. The higher rates for COD removal, nitrification, and denitrification were achieved in R2 than R1 with similar influent quality. Dissolved oxygen (DO), pH, and oxidization reduction potential, corresponding to nutrient variations, were used as diagnostic parameters to control the organic carbon degradation and nitrification–denitrification via nitrite processes in both SBRs. The online control strategy of granular SBR was similar to that of the SBR with flocculent activated sludge. However, a unique U-type pattern on the DO curve in granular SBR was different from SBR with flocculent activated sludge in aerobic phase.     

Enhanced nutrient removal in three types of step feeding process from municipal wastewater

An anoxic/oxic step feeding process was improved to enhance nutrient removal by reconfiguring the process into (1) anaerobic/anoxic/oxic step feeding process or (2) modified University of Capetown (UCT) step feeding process. Enhanced nitrogen and phosphorus removal and optimized organics utilization were obtained simultaneously in the modified UCT type with both internal and sludge recycle ratios of 75% as well as anaerobic/anoxic/oxic volume ratio of 1:3:6. Specifically, the UCT configuration and optimized operational conditions lead to the enrichment of denitrifying phosphorus removal microorganisms and achieved improved anaerobic P-release and anoxic P-uptake activities, which were beneficial to the denitrifying phosphorus removal activities and removal efficiencies. Due to high mixed liquor suspended solid and uneven distributed dissolved oxygen, 35% of total nitrogen was eliminated through simultaneous nitrification and denitrification process in aerobic zones. Moreover, 62 ± 6% of influent chemical oxygen demands was involved in the denitrification or phosphorus release processes.     

Organic and nitrogen removal in a two-stage rotating biological contactor treating municipal wastewater

A laboratory scale rotating biological contactor (RBC) predenitrification system incorporating anoxic and aerobic units was evaluated for the treatment of settled high-strength municipal wastewater. The system was operated under four recycle ratios (1, 2, 3 and 4) and loading rates of 38-182 gCOD/m(2)d and 0.22-14 gOxid-N/m(2)d on the anoxic unit and 3.4-18 gCOD/m(2)d and 0.24-1.8 gNH(4)-N/m(2)d on the aerobic. The average removal efficiency in terms of chemical oxygen demand (COD), biochemical oxygen demand (BOD(5)), total suspended solids (TSS) and total nitrogen (Total-N) was 82%, 86%, 63% and 54%; settling of the RBC effluent increased COD and TSS removal to 94% and 97%. An increase in hydraulic loading resulting from higher recirculation, had limited negative effect on organic removal but improved nitrogen removal, and in terms of Total-N removal efficiency increased up to a ratio of 3 and then decreased.     

Simultaneous estimation of sludge biological activity and influent nitrogen load using ORP and DO dynamics

This paper proposes a new optimization strategy to estimate nitrifiable nitrogen concentration in wastewater, nitrification rate, denitrification rate and/or COD available for denitrification of an activated sludge process submitted to intermittent aeration. The approach uses the oxydo-reduction potential and dissolved oxygen measurements only. The parameter identification is based on a Simplex optimization of a cost function related to the error between an experimental cycle (an aerobic period followed by an anoxic one) and a simulation of a reduced model derived from ASM1. Results show very good prediction of experimental oxygen, ammonium and nitrate profiles. The estimation of nitrifiable nitrogen and removal rates has been validated both on simulated data obtained from COST action 624 benchmark and on experimental data.     

Effect of oxic and anoxic conditions on nitrous oxide emissions from nitrification and denitrification processes

A lab-scale sequencing batch reactor fed with real municipal wastewater was used to study nitrous oxide (N(2)O) emissions from simulated wastewater treatment processes. The experiments were performed under four different controlled conditions as follows: (1) fully aerobic, (2) anoxic-aerobic with high dissolved oxygen (DO) concentration, (3) anoxic-aerobic with low DO concentration, and 4) intermittent aeration. The results indicated that N(2)O production can occur from both incomplete nitrification and incomplete denitrification. N(2)O production from denitrification was observed in both aerobic and anoxic phases. However, N(2)O production from aerobic conditions occurred only when both low DO concentrations and high nitrite concentration existed simultaneously. The magnitude of N(2) O produced via anoxic denitrification was lower than via oxic denitrification and required the presence of nitrite. Changes in DO, ammonium, and nitrite concentrations influenced the magnitude of N(2)O production through denitrification. The results also suggested that N(2)O can be produced from incomplete denitrification and then released to the atmosphere during aeration phase due to air stripping. Therefore, biological nitrogen removal systems should be optimized to promote complete nitrification and denitrification to minimize N(2)O emissions.     

Enhanced aerobic granulation and nitrogen removal by the addition of zeolite powder in a sequencing batch reactor

The aim of this study was to evaluate the impact of zeolite powders on feasibility of rapid aerobic granulation in the column-type sequencing batch reactors. After 90 days' operation, aerobic granular sludge was formed in both reactors by altering influent chemical oxygen demand/nitrogen (COD/N) ratios. R1 with zeolite powders had better removal capabilities of COD and total nitrogen than R2, which was without zeolite powders. Mixed liquor volatile suspended solid concentrations of the two reactors were 7.36 and 5.45 g/L, while sludge volume index (SVI₃₀) values were 34.9 and 47.9 mg/L, respectively. The mean diameters of aerobic granular sludge in the above two reactors were 2.5 and 1.5 mm, respectively. Both reactors achieved the largest simultaneous nitrification and denitrification (SND) efficiency at an influent COD/N ratio of 8; however, R1 exhibited more excellent SND efficiency than R2. The obtained results could provide a novel technique for rapid aerobic granulation and N removal simultaneously, especially when treating nitrogen-rich industrial wastewater.     

The performance and microbial communities of biodegradation-electron transfer with sulfur metabolism integrated process for flue gas desulfurization wastewater treatment

The biodegradation-electron transfer with sulfur metabolism integrated (BESI®) process was used for the treatment of real flue gas desulfurization wastewater. The BESI® process consists of an anaerobic activated sludge reactor, an anoxic activated sludge reactor, and an aerobic bio-film reactor. The performance of the integrated process was evaluated by the removal efficiencies of organics and nitrogen pollutants. The sulfate in the wastewater was used as an abundant sulfur source to drive the integrated process. The removal efficiencies of chemical oxygen demand, total organic carbon, ammonia nitrogen, and total nitrogen of the integrated process were 87.99, 87.04, 30.77, and 45.17%, respectively. High-throughput 454-pyrosequencing was applied for the analysis of microbial communities in the integrated process. From the anaerobic activated sludge (Sample 1), anoxic activated sludge (Sample 2), and aerobic bio-film (Sample 3), totals of 1701, 1181, and 857 operational taxonomic units were obtained, respectively. The sulfur cycle was associated with the removal of organics and nitrogen pollutants. The sulfate-reducing bacteria participated in the organics removal in the anaerobic reactor, and the sulfide oxidation was related with the denitrification in the anoxic reactor. A complete nitrogen degradation chain was built in the integrated process. Through the degradation chain, the nitrogenous organic pollutants, ammonia nitrogen, and nitrate could be removed. The participant functional bacteria were also detected by pyrosequencing.     

Nutrient removal and sludge age in a sequencing batch reactor

The aim of this work was to establish a relation between the mean cellular retention time and the ability of activated sludge to remove phosphate and ammonium. A sequencing batch reactor (SBR) with a total volume of 1.94 m³ was fed with municipal wastewater and was operated under four different organic loading rates to obtain sludge ages of 23, 16, 6, and 3 days. The operational strategy included fill, anaerobic, aerobic, settling and draw phases. The experimental work lasted 445 days. Biological phosphate removal was achieved with sludge ages from 6 to 23 days. The highest PO₄-P removal rate observed was of 98% and corresponds to a 16-day sludge age; phosphate removal increased with the sludge age. A sludge age of 3 days resulted in a chemical oxygen demand (COD) removal rate of 81% and a sludge age of 23 days in a removal rate of 99%. Full nitrification was observed with a sludge age of 16 days. Nitrification increased with the sludge age. The 3-day sludge age did not allow nitrification. The phosphate concentrations in the biomass were inversely proportional to the sludge age.     

Effects of synthetic polymer on the filamentous bacteria in activated sludge

Filamentous bulking is one of the solid-liquid separation problems always seen in activated sludge process. The addition of synthetic polymer is always one of the popular ways for the treatment plant operator to immediately solve the poor sludge settling problem. Therefore, it may be interesting to understand the effects of synthetic polymer on the filamentous bacteria in activated sludge. In this study, synthetic polymer was applied to a lab-scale wastewater treatment system with the filamentous bulking problem. The population structure of filamentous bacteria and sludge characteristics were investigated under different conditions. When synthetic polymer was added into the system, it was found that poor sludge settleability caused by filamentous bulking was temporarily solved and filamentous branches growing outside the flocs were damaged or inhibited. However, filamentous growth was still observed inside the flocs. After the addition of polymer was halted, filamentous branches extended out of the flocs immediately. Very serious filamentous bulking occurred and sludge settleability became much worse than that occurring before the addition of polymer. And, it took several weeks for the system to return to normal operation.     

Effect of COD/N ratio on cultivation of aerobic granular sludge in a pilot-scale sequencing batch reactor

Aerobic granular sludge was successfully cultivated with the effluent of internal circulation reactor in a pilot-scale sequencing batch reactor (SBR). Soy protein wastewater was used as an external carbon source for altering the influent chemical oxygen demand/nitrogen (COD/N) ratios of SBR. Initially, the phenomenon of partial nitrification was observed and depressed by increasing the influent COD/N ratios from 3.32 to 7.24 mg/mg. After 90 days of aerobic granulation, the mixed liquor suspended solids concentration of the reactor increased from 2.80 to 7.02 g/L, while the sludge volumetric index decreased from 105.51 to 42.99 mL/g. The diameters of mature aerobic granules vary in the range of 1.2 to 2.0 mm. The reactor showed excellent removal performances for COD and $ {\text{NH}}_4^{ + }{\text{ - N}} $ after aerobic granulation, and average removal efficiencies were over 93% and 98%, respectively. The result of this study could provide further information on the development of aerobic granule-based system for full-scale applications.