Short-cut nitrification of domestic wastewater in a pilot-scale A/O nitrogen removal plant

The feasibility of nitrite accumulation in a pilot-scale A/O (anoxic/oxic) nitrogen removal plant treating domestic wastewater was investigated at various dissolved oxygen (DO) concentrations and pH levels. The results showed that the pH was not a useful operational parameter to realize nitrite accumulation. Significant nitrite accumulation was observed at the low DO concentration range of 0.3–0.8 mg/l and the maximum nitrite accumulation ratio of about 90% occurred at a DO concentration of 0.6 mg/l. This suggests a reduction of 22% in the oxygen consumption, and therefore a considerable saving in aeration. However, the nitrite accumulation was destroyed at the high DO concentration and the resumption was very slow. In addition, the average ammonia removal efficiency reached as high as 93% at the low DO level. Moreover, experimental results indicated that nitrogen could be removed by simultaneous nitrification and denitrification (SND) via nitrite in the aerobic zones at the low DO concentration, with the efficiency of 6–12%.     

Simultaneous nitrification,denitrification, and phosphorus removal in a lab-scale sequencing batch reactor

Simultaneous nitrification and denitrification (SND) via the nitrite pathway and anaerobic-anoxic-enhanced biological phosphorus removal (EBPR) are two processes that can significantly reduce the energy and COD demand for nitrogen and phosphorus removal. The combination of these two processes has the potential of achieving simultaneous nitrogen and phosphorus removal with a minimal requirement for COD. A lab-scale sequencing batch reactor (SBR) was operated in alternating anaerobic-aerobic mode with a low dissolved oxygen (DO) concentration (0.5 mg/L) during the aerobic period, and was demonstrated to accomplish nitrification, denitrification, and phosphorus removal. Under anaerobic conditions, COD was taken up and converted to polyhydroxyalkanoates (PHAs), accompanied by phosphorus release. In the subsequent aerobic stage, PHA was oxidized and phosphorus was taken up to <0.5 mg/L by the end of the cycle. Ammonia was also oxidized during the aerobic period, but without accumulation of nitrite or nitrate in the system, indicating the occurrence of simultaneous nitrification and denitrification. However, off-gas analysis showed that the final denitrification product was mainly nitrous oxide (N(2)O), not N(2). Further experimental results demonstrated that nitrogen removal was via nitrite, not nitrate. These experiments also showed that denitrifying glycogen-accumulating organisms (DGAOs), rather than denitrifying polyphosphate-accumulating organisms (DPAOs), were responsible for the denitrification activity.     

Enhanced biological nitrogen removal and N<Subscript>2</Subscript>O emission characteristics of the intermittent aeration activated sludge process

Enhanced biological nitrogen removal processes are necessarily required to cope with more stringent wastewater discharging regulations, especially for wastewater with low level of organic carbon to nitrogen ratios. The intermittent aeration activated sludge process has been received comprehensive attention over the past decades, due to its excellent performance in nitrogen removal and remarkable reduction of energy consumption. Recent advances for this technology was reviewed from aspects of characteristics of system, factors affecting nitrogen removal, nitrous oxide (N₂O) emission and its control, and application of the technology and its operation control. Finally, future development was proposed. In the intermittent aeration activated sludge process, aeration duration should be controlled for adequate nitrification and non-aeration duration should be adequate for complete denitrification, and these would benefit both nitrogen removal and N₂O mitigation. The step feed strategy could be applied to enhance the better utilization of influent organic carbon for nitrogen removal. Dissolved oxygen (DO) and aerobic duration both affected nitrogen removal in particular that via nitrite in the intermittent aeration process. Nitrite should be removed efficiently to avoid a high N₂O emission under both anoxic and aerobic conditions. Intermittent aeration activated sludge process has been applied in the treatment of various wastewaters, such as municipal wastewater, swine wastewater, anaerobic effluents and landfill leachate. For practical application, DO, pH and oxidation–reduction potential could be used as indices for controlling nitrogen removal and N₂O mitigation. Microbial ecology in the intermittent aeration activated sludge process should be specifically focused in future studies.     

Nitrous oxide production by Alcaligenes faecalis under transient and dynamic aerobic and anaerobic conditions.

Nitrous oxide can be a harmful by-product in nitrogen removal from wastewater. Since wastewater treatment systems operate under different aeration regimens, the influence of different oxygen concentrations and oxygen fluctuations on denitrification was studied. Continuous cultures of Alcaligenes faecalis TUD produced N2O under anaerobic as well as aerobic conditions. Below a dissolved oxygen concentration of 5% air saturation, the relatively highest N2O production was observed. Under these conditions, significant activities of nitrite reductase could be measured. After transition from aerobic to anaerobic conditions, there was insufficient nitrite reductase present to sustain growth and the culture began to wash out. After 20 h, nitrite reductase became detectable and the culture started to recover. Nitrous oxide reductase became measurable only after 27 h, suggesting sequential induction of the denitrification reductases, causing the transient accumulation of N2O. After transition from anaerobic conditions to aerobic conditions, nitrite reduction continued (at a lower rate) for several hours. N2O reduction appeared to stop immediately after the switch, indicating inhibition of nitrous oxide reductase, resulting in high N2O emissions (maximum, 1.4 mmol liter-1 h-1). The nitrite reductase was not inactivated by oxygen, but its synthesis was repressed. A half-life of 16 to 22 h for nitrite reductase under these conditions was calculated. In a dynamic aerobic-anaerobic culture of A. faecalis, a semisteady state in which most of the N2O production took place after the transition from anaerobic to aerobic conditions was obtained. The nitrite consumption rate in this culture was equal to that in an anaerobic culture (0.95 and 0.92 mmol liter-1 h-1, respectively), but the production of N2O was higher in the dynamic culture (28 and 26% of nitrite consumption, respectively).     

Shortcut biological nitrogen removal in hybrid biofilm/suspended growth reactors

A shortcut biological nitrogen removal (SBNR) process converts ammonium directly through nitrite to nitrogen gas, thus requiring less aeration and carbon. We evaluated a hybrid SBNR (HSBNR) reactor containing an anoxic tank followed by an aerobic tank and a settling tank. The aerobic tank was filled with polyvinyl alcohol sponge media (20%, v/v) to attach and retain ammonium oxidizers. Two configurations of the HSBNR reactor were tested for treating a wastewater with high strength ammonium and organic electron donor. The HSNBR reactors accumulated nitrite stably for 1.5 years and maintained a high free ammonia (FA) concentration (20–25 mg/L) and a low dissolved oxygen (DO) concentration (<1 mg/L) in the aerobic tank. Apparently, the biofilm carriers increased the solids retention time (SRT) for ammonium oxidizers, while high FA and low DO selected against nitrite oxidizers and promoted direct denitrification of nitrite in the aerobic tank. The significant amount of chemical oxygen demand (COD) was removed by shortcut denitrification of nitrite in the anoxic tank.     

Air-lift internal loop biofilm reactor for realized simultaneous nitrification and denitrification

Simultaneous nitrification and denitrification (SND) was realized by means of a novel air-lift internal loop biofilm reactor, in which aeration was set in middle of the reactor. During operation, the aeration was adjusted to get appropriate dissolve oxygen (DO) in bulk solution and let aerobic and anoxic zone coexist in one reactor. When aeration was at 0.6 and 0.2 L/min, corresponding to DO of 5.8 and 2.5 mg/L in bulk solution, ammonia nitrogen removal percentage reached about 80 and 90 %, but total nitrogen removal percentage was lower than 25 %. While the aeration was reduced to 0.1 L/min, aerobic and anoxic zones existed simultaneously in one reactor to get 75 % of ammonia nitrogen and 50 % of total nitrogen removal percentage. Biofilms were, respectively, taken from aerobic and anoxic zone to verify their function of nitrification and denitrification in two flasks, in which ammonia nitrogen was transferred into nitrate completely by aerobic biofilm, and nitrate was removed more than 80 % by anoxic biofilm. Microelectrode was used to measure the DO distribution inside biofilms in anoxic zone corresponding to different aerations. When aeration was at 0.6 and 0.2 L/min, DO inside biofilm was more than 1.5 mg/L, but the DO inside biofilm decreased to anoxic status with depth of biofilm increasing corresponding to aeration of 0.1 L/min. The experimental results indicated that SND could be realized because of simultaneous existence of aerobic and anoxic biofilms in one reactor.     

Comparison of biological removal via nitrite with real-time control using aerobic granular sludge and flocculent activated sludge

The process of nitrification–denitrification via nitrite for nitrogen removal under real-time control mode was tested in two laboratory-scale sequencing batch reactors (SBRs) with flocculent activated sludge (R1) and aerobic granular sludge (R2) to compare operational performance and real-time control strategies. The results showed that the average ammonia nitrogen, total inorganic nitrogen (TIN), and chemical oxygen demand (COD) removal during aeration phase were 97.6%, 57.0%, and 90.1% in R2 compared with 98.6%, 48.7%, and 88.1% in R1. The TIN removed in both SBRs was partially due to the presence of simultaneous nitrification–denitrification via nitrite, especially in R2. The specific nitrification and denitrification rates in R2 were 0.0416 mgNH₄⁺–N/gSS-min and 0.1889 mgNO_X⁻–N/gSS-min, which were 1.48 times and 1.35 times that of R1. The higher rates for COD removal, nitrification, and denitrification were achieved in R2 than R1 with similar influent quality. Dissolved oxygen (DO), pH, and oxidization reduction potential, corresponding to nutrient variations, were used as diagnostic parameters to control the organic carbon degradation and nitrification–denitrification via nitrite processes in both SBRs. The online control strategy of granular SBR was similar to that of the SBR with flocculent activated sludge. However, a unique U-type pattern on the DO curve in granular SBR was different from SBR with flocculent activated sludge in aerobic phase.     

Nitrogen transformations during biological aerobic treatment of pig slurry: effect of intermittent aeration on nitrous oxide emissions

A laboratory scale aeration treatment system was built to study the fate of nitrogen during aeration of pig slurry. For each run evaluated, the nitrogen mass balance was determined including measurement of the nitrous oxide gas emissions. Intermittent aeration led to a nitrogen removal of about 53% of the total nitrogen content of the raw slurry. About 18% of the total nitrogen content of the raw slurry was emitted as N2O during aeration with an aerobic to anoxic ratio equal to 0.625. In contrast, the extension of the anoxic period (aerobic to anoxic ratio = 0.375) allowed complete denitrification and avoided N2O emissions.     

间歇曝气对微污染源水生物接触氧化修复系统脱氮性能的影响

针对寡营养生境下生物脱氮过程碳源不足等问题,开展不同间歇曝气方式对微污染源水生物接触氧化修复系统脱氮性能的影响研究,探究修复系统短程硝化反硝化的可行性与过程机理.结果表明:在停曝-曝气时间为8 h-16 h的间歇曝气方式(Ⅰ)下启动的生物接触氧化修复系统,其铵态氮(NH+4-N)、高锰酸盐指数(CODMn)、总氮(TN)的平均去除率分别稳定在93.0%、78.1%、19.4%;而在停曝-曝气时间为16 h-8 h的间歇曝气方式(Ⅱ)下运行修复系统,其NH+4-N、CODMn平均去除率仍能分别维持在81.2%、76.4%,体系内NO-2-N发生积累,TN去除率增至50%以上.对工况Ⅱ下修复系统周期内氮素转化特性分析发现,在确保出水NH+4-N、溶解氧(DO)浓度达标的前提下,缩短曝气时间可将体系DO长时间控制在0.5～1.5 mg·L-1,亚硝酸氧化菌(NOB)生长及其活性受到抑制,NO-2-N明显累积,最终实现了微污染源水生物接触氧化修复系统的短程生物脱氮.     

Modelling of biological processes during aerobic treatment of piggery wastewater aiming at process optimisation

A dynamic mathematical model was developed for the simulation of the aerobic treatment of piggery wastewater. This model includes the carbon oxidation, the nitrification and the denitrification. According to the experimental results obtained during this study, a modified version of the activated sludge model No. 1 has been developed. The model includes (1) nitrite as intermediate of nitrification and denitrification, (2) the distinction between the anoxic heterotrophic yield and the aerobic heterotrophic yield, respectively equal to 0.53 and 0.6 and (3) the first-order hydrolysis of the slowly biodegradable fraction. The calibration and the validation of the model was performed using experimental data from three experiments with two piggery wastewaters. A set of kinetic and stoichiometric parameters emerged from these tests. Except the kinetic of hydrolysis of the slowly biodegradable organic matter varying from 6 to 25 gCOD(gCODday)(-1), all other parameters were similar for all experiments. The dissolved oxygen concentration was identified as the main variable influencing the nitrite accumulation during nitrification. In the calibrated model, the oxygen half-saturation coefficient of the ammonium oxidisers (0.3g O(2)m(-3)) was lower than for the nitrite oxidisers (1.1 gO(2)m(-3)), leading to nitrite accumulation when the dissolved oxygen concentration was low. Simulations with the proposed model could be very useful for improved design and management of biological treatment of piggery wastewaters, particularly in case of partial nitrification to nitrite directly followed by denitrification.     

Nitrous oxide emissions from denitrifying activated sludge of urban wastewater treatment plants, under anoxia and low oxygenation

Batch experiments were made to better understand the mechanisms of N2O emissions from activated sludge in denitrifying conditions found in urban WWTPs, i.e. under anoxic and low oxygenation conditions. The results showed that in completely anoxic conditions, denitrification, related to a periplasmic nitrate reductase activity, is the major producer of N2O (100% of the N2O production), whereas the nitrate ammonifying activity is not significant. In a gradient of low oxygenation, the highest N2O emissions (49.7+/-3.8 microg N2O-N/g SS/h on average) occurred at a dissolved-oxygen concentration of around 0.3mg O2/L. Below 0.3mg O2/L, heterotrophic denitrification appeared to be the major process responsible for the N2O emission (100% at zero oxygenation). From 0.4 to 1.1mg O2/L, N2O emissions were due to two processes: (i) heterotrophic denitrification that represented about 40% of the N2O production, and (ii) autotrophic nitrifier denitrification that accounted for about 60%. The N2O emissions from activated sludge represented on average 0.4% of reduced NO3(-) in anoxic conditions. The N2O emissions associated with denitrification of entire nitrogen load would amount to 155 T N2O-N/year, if all the Paris wastewater was treated by a process using activated sludge.     

Nitrification-denitrification via nitrite accumulation for nitrogen removal from wastewaters

The biological nitrification-denitrification process is used extensively for removal of ammonia nitrogen from wastewaters. Saves in aeration, organic matter (for denitrification) and surplus sludge are achievable if nitrite accumulation is possible in the nitrification step. In this paper, operational parameters were studied for each process for maximum nitrite accumulation in the nitrification step and nitrite adaptation in the denitrification step. Nitrite accumulation during nitrification can be controlled by the dissolved oxygen (DO) concentration, presenting a maximum of 65% at around 0.7 mg DO/L. Denitrification can be adapted to nitrite and the process is stable if nitrite in the reactor is keep low. The performance of a continuous stirred tank reactor (CSTR) and an up flow sludge blanket reactor (USB) were compared. Once the operational parameters were established, a CSTR for nitrification and an USB reactor for denitrification were operated in series for 25 days. The process was stable and a steady state was maintained for 20 days, and 93.5% of overall nitrogen removal was achieved in the nitrification-denitrification via the nitrite process.     

Effects of loading rate and aeration on nitrogen removal and N<Subscript>2</Subscript>O emissions in intermittently aerated sequencing batch reactors treating slaughterhouse wastewater at 11 °C

This study aimed to find optimal operation conditions for nitrogen removal from high strength slaughterhouse wastewater at 11 °C using the intermittently aerated sequencing batch reactors (IASBRs) so as to provide an engineering control strategy for the IASBR technology. Two operational parameters were examined: (1) loading rates and (2) aeration rates. Both the two parameters affected variation of DO concentrations in the IASBR operation cycles. It was found that to achieve efficient nitrogen removal via partial nitrification–denitrification (PND), “DO elbow” point must appear at the end of the last aeration period. There was a correlation between the ammonium oxidizing bacteria (AOB)/nitrite oxidizing bacteria (NOB) ratio and the average DO concentrations in the last aeration periods; when the average DO concentrations in the last aeration periods were lower than 4.86 mg/L, AOB became the dominant nitrifier population, which benefited nitrogen removal via PND. Both the nitrogen loading rate and the aeration rate influenced the population sizes of AOB and NOB. To accomplish efficient nitrogen removal via PND, the optimum aeration rate (A, L air/min) applied can be predicted according to the average organic loading rates based on mathematical equations developed in this study. The research shows that the amount of N₂O generation in the aeration period was reduced with increasing the aeration rate; however, the highest N₂O generation in the non-aeration period was observed at the optimum aeration rates.     

Effect of ammonium concentration on the emission of N(2)O under oxygen-limited autotrophic wastewater nitrification

A significant amount of nitrous oxide (N(2)O), which is one of the serious greenhouse gases, is emitted from nitrification and denitrification of wastewater. Batch wastewater nitrifications with enriched nitrifiers were carried out under oxygen-limited condition with synthetic (without organic carbon) and real wastewater (with organic carbon) in order to find out the effect of ammonium concentration on N(2)O emission. Cumulated N(2)O-N emission reached 3.0, 5.7, 6.2, and 13.5 mg from 0.4 l of the synthetic wastewater with 50, 100, 200, and 500 mg/l NH(4)(+)-N, respectively, and 1.0 mg from the real wastewater with 125 mg/l NH(4)(+)-N. The results indicate that N(2)O emission increased with ammonium concentration and the load. The ammonium removal rate and nitrite concentration also increased N(2)O emission. Comparative analysis of N(2)O emission from synthetic and real wastewaters revealed that wastewater nitrification under oxygen-limited condition emitted more N(2)O than that of heterotrophic denitrification. Summarizing the results, it can be concluded that denitrification by autotrophic nitrifiers contributes significantly to the N(2)O emission from wastewater nitrification.     

Effect of oxygen concentration on nitrification and denitrification in single activated sludge flocs

Simultaneous nitrification and denitrification (SND) was investigated in the single aeration tank of a municipal wastewater treatment plant. Microelectrode measurements and batch experiments were performed to test for the presence of SND. Microelectrodes recorded the presence of O(2) concentration gradients in individual activated sludge flocs. When the O(2) concentration in the bulk liquid was <45 microM, anoxic zones were detected within flocs with a larger diameter (approximately 3000 microm). The O(2) penetration depth in the floc was found to be dependent on the O(2) concentration in the bulk liquid. Nitrification was restricted to the oxic zones, whereas denitrification occurred mainly in the anoxic zones. The nitrification rate of the activated sludge increased with increasing O(2) concentration in the bulk liquid, up to 40 microM, and remained constant thereafter. SND was observed in the aerated activated sludge when O(2) concentration was in the range of 10 to 35 microM.     

Nitrous oxide production by lithotrophic ammonia-oxidizing bacteria and implications for engineered nitrogen-removal systems

Chemolithoautotrophic AOB (ammonia-oxidizing bacteria) form a crucial component in microbial nitrogen cycling in both natural and engineered systems. Under specific conditions, including transitions from anoxic to oxic conditions and/or excessive ammonia loading, and the presence of high nitrite (NO??) concentrations, these bacteria are also documented to produce nitric oxide (NO) and nitrous oxide (N?O) gases. Essentially, ammonia oxidation in the presence of non-limiting substrate concentrations (ammonia and O?) is associated with N?O production. An exceptional scenario that leads to such conditions is the periodical switch between anoxic and oxic conditions, which is rather common in engineered nitrogen-removal systems. In particular, the recovery from, rather than imposition of, anoxic conditions has been demonstrated to result in N?O production. However, applied engineering perspectives, so far, have largely ignored the contribution of nitrification to N?O emissions in greenhouse gas inventories from wastewater-treatment plants. Recent field-scale measurements have revealed that nitrification-related N?O emissions are generally far higher than emissions assigned to heterotrophic denitrification. In the present paper, the metabolic pathways, which could potentially contribute to NO and N?O production by AOB have been conceptually reconstructed under conditions especially relevant to engineered nitrogen-removal systems. Taken together, the reconstructed pathways, field- and laboratory-scale results suggest that engineering designs that achieve low effluent aqueous nitrogen concentrations also minimize gaseous nitrogen emissions.     

Survival of the aerobic denitrifier Pseudomonas stutzeri strain TR2 during co-culture with activated sludge under denitrifying conditions

The aerobic denitrifier Pseudomonas stutzeri TR2 (strain TR2) has the potential to reduce nitrous oxide emissions during the wastewater treatment process. In this application, it is important to find the best competitive survival conditions for strain TR2 in complex ecosystems. To that end, we examined co-cultures of strain TR2 with activated sludge via five passage cultures in a medium derived from treated piggery wastewater that contained a high concentration of ammonium. The results are as follows: (i) The medium supported the proliferation of strain TR2 (P. stutzeri strains) under denitrifying conditions. (ii) Nitrite was a better denitrification substrate than nitrate for TR2 survival. (iii) Strain TR2 also demonstrated strong survival even under aerobic conditions. This suggests that strain TR2 is effectively augmented to the wastewater treatment process, aiding in ammonium-nitrogen removal and reducing nitrous oxide production with a partial nitrification technique in which nitrite accumulates.     

A comparison of NO and N2O production by the autotrophic nitrifier Nitrosomonas europaea and the heterotrophic nitrifier Alcaligenes faecalis.

Soil microorganisms are important sources of the nitrogen trace gases NO and N2O for the atmosphere. Present evidence suggests that autotrophic nitrifiers such as Nitrosomonas europaea are the primary producers of NO and N2O in aerobic soils, whereas denitrifiers such as Pseudomonas spp. or Alcaligenes spp. are responsible for most of the NO and N2O emissions from anaerobic soils. It has been shown that Alcaligenes faecalis, a bacterium common in both soil and water, is capable of concomitant heterotrophic nitrification and denitrification. This study was undertaken to determine whether heterotrophic nitrification might be as important a source of NO and N2O as autotrophic nitrification. We compared the responses of N. europaea and A. faecalis to changes in partial O2 pressure (pO2) and to the presence of typical nitrification inhibitors. Maximal production of NO and N2O occurred at low pO2 values in cultures of both N. europaea (pO2, 0.3 kPa) and A. faecalis (pO2, 2 to 4 kPa). With N. europaea most of the NH4+ oxidized was converted to NO2-, with NO and N2O accounting for 2.6 and 1% of the end product, respectively. With A. faecalis maximal production of NO occurred at a pO2 of 2 kPa, and maximal production of N2O occurred at a pO2 of 4 kPa. At these low pO2 values there was net nitrite consumption. Aerobically, A. faecalis produced approximately the same amount of NO but 10-fold more N2O per cell than N. europaea did. Typical nitrification inhibitors were far less effective for reducing emissions of NO and N2O by A. faecalis than for reducing emissions of NO and N2O by N. europaea.(ABSTRACT TRUNCATED AT 250 WORDS)     

Long-term effect of dissolved oxygen on partial nitrification performance and microbial community structure

In this study, the performance of partial nitrification via nitrite and microbial community structure were investigated and compared in two sequencing batch reactors (SBR) with different dissolved oxygen (DO) levels. Both reactors achieved stable partial nitrification with nitrite accumulation ratio of above 95% by using real-time aeration duration control. Compared with high DO (above 3 mg/l on average) SBR, simultaneous nitrification and denitrification (SND) via nitrite was carried out in low DO (0.4–0.8 mg/l) SBR. The average efficiencies of SND in high DO and low DO reactor were 7.7% and 44.9%, and the specific SND rates were 0.20 and 0.83 mg N/(mg MLSS h), respectively. Low DO did not produce sludge with poorer settling properties but attained lower turbidities of the effluent than high DO. Fluorescence in situ hybridization (FISH) analysis in both the reactors showed that ammonia-oxidizing bacteria (AOB) were the dominant nitrifying bacteria and nitrite-oxidizing bacteria (NOB) did not be recovered in spite of exposing nitrifying sludge to high DO. The morphology of the sludge from both two reactors according to scanning electron microscope indicated that small rod-shaped and spherical clusters were dominant, although filamentous bacteria and few long rod-shaped coexisted in the low DO reactor. By selecting properly DO level and adopting process control method is not only of benefit to the achievement of novel biological nitrogen removal technology, but also favorable to sludge population optimization.     

Identification of novel small molecule enhancers of protein production by cultured mammalian cells

Shortcut nitrogen removal, that is, removal via formation and reduction of nitrite rather than nitrate, has been observed in membrane-aerated biofilms (MABs), but the extent, the controlling factors, and the kinetics of nitrite formation in MABs are poorly understood. We used a special MAB reactor to systematically study the effects of the dissolved oxygen (DO) concentration at the membrane surface, which is the biofilm base, on nitrification rates, extent of shortcut nitrification, and microbial community structure. The focus was on anoxic bulk liquids, which is typical in MAB used for total nitrogen (TN) removal, although aerobic bulk liquids were also studied. Nitrifying MABs were grown on a hollow-fiber membrane exposed to 3 mg N/L ammonium. The MAB intra-membrane air pressure was varied to achieve different DO concentrations at the biofilm base, and the bulk liquid was anoxic or with 2 g m(-3) DO. With 2.2 and 3.5 g m(-3) DO at the biofilm base, and with an anoxic bulk-liquid, the ammonium fluxes were 0.75 and 1.0 g N m(-2) day(-1), respectively, and nitrite was the main oxidized nitrogen product. However, with membrane DO of 5.5 g m(-3), and either zero or 2 g m(-3) DO in the bulk, the ammonium flux was around 1.3 g N m(-2) day(-1), and nitrate flux increased significantly. For all experiments, the cell density of ammonium oxidizing bacteria (AOB) was relatively uniform throughout the biofilm, but the density of nitrite oxidizing bacteria (NOB) decreased with decreasing biofilm DO. Among NOB, Nitrobacter spp. were dominant in biofilm regions with 2 g m(-3) DO or greater, while Nitrospira spp. were dominant in regions with less than 2 g m(-3) DO. A biofilm model, including AOB, Nitrobacter spp., and Nitrospira spp., was developed and calibrated with the experimental results. The model predicted the greatest extent of nitrite formation (95%) and the lowest ammonium oxidation flux (0.91 g N m(-2) day(-1)) when the membrane DO was 2 g m(-3) and the bulk liquid was anoxic. Conversely, the model predicted the lowest extent of nitrite formation (40%) and the highest ammonium oxidation flux (1.5 g N m(-2) day(-1)) when the membrane-DO and bulk-DO were 8 g m(-3) and 2 g m(-3), respectively. The estimated kinetic parameters for Nitrospira spp., revealed a high affinity for nitrite and oxygen. This explains the dominance of Nitrospira spp. over Nitrobacter spp. in regions with low nitrite and oxygen concentrations. Our results suggest that shortcut nitrification can effectively be controlled by manipulating the DO at the membrane surface. A tradeoff is made between increased nitrite accumulation at lower DO, and higher nitrification rates at higher DO.