A High‐Performance D–A Copolymer Based on Dithieno[3,2‐b:2′,3′‐d]Pyridin‐5(4H)‐One Unit Compatible with Fullerene and Nonfullerene Acceptors in Solar Cells

Development of high‐performance donor–acceptor (D–A) copolymers is vital in the research of polymer solar cells (PSCs). In this work, a low‐bandgap D–A copolymer based on dithieno[3,2‐b:2′,3′‐d]pyridin‐5(4H)‐one unit (DTP), PDTP4TFBT, is developed and used as the donor material for PSCs with PC₇₁BM or ITIC as the acceptor. PDTP4TFBT:PC₇₁BM and PDTP4TFBT:ITIC solar cells give power conversion efficiencies (PCEs) up to 8.75% and 7.58%, respectively. 1,8‐Diiodooctane affects film morphology and device performance for fullerene and nonfullerene solar cells. It inhibits the active materials from forming large domains and improves PCE for PDTP4TFBT:PC₇₁BM cells, while it promotes the aggregation and deteriorates performance for PDTP4TFBT:ITIC cells. The ternary‐blend cells based on PDTP4TFBT:PC₇₁BM:ITIC (1:1.2:0.3) give a decent PCE of 9.20%.     

Rational Strategy to Stabilize an Unstable High‐Efficiency Binary Nonfullerene Organic Solar Cells with a Third Component

Long device lifetime is still a missing key requirement in the commercialization of nonfullerene acceptor (NFA) organic solar cell technology. Understanding thermodynamic factors driving morphology degradation or stabilization is correspondingly lacking. In this report, thermodynamics is combined with morphology to elucidate the instability of highly efficient PTB7‐Th:IEICO‐4F binary solar cells and to rationally use PC₇₁BM in ternary solar cells to reduce the loss in the power conversion efficiency from ≈35% to <10% after storage for 90 days and at the same time improve performance. The hypomiscibility observed for IEICO‐4F in PTB7‐Th (below the percolation threshold) leads to overpurification of the mixed domains. By contrast, the hypermiscibility of PC₇₁BM in PTB7‐Th of 48 vol% is well above the percolation threshold. At the same time, PC₇₁BM is partly miscible in IEICO‐4F suppressing crystallization of IEICO‐4F. This work systematically illustrates the origin of the intrinsic degradation of PTB7‐Th:IEICO‐4F binary solar cells, demonstrates the structure–function relations among thermodynamics, morphology, and photovoltaic performance, and finally carries out a rational strategy to suppress the degradation: the third component needs to have a miscibility in the donor polymer at or above the percolation threshold, yet also needs to be partly miscible with the crystallizable acceptor.     

Study of Burn‐In Loss in Green Solvent‐Processed Ternary Blended Organic Photovoltaics Derived from UV‐Crosslinkable Semiconducting Polymers and Nonfullerene Acceptors

This work deals with the investigation of burn‐in loss in ternary blended organic photovoltaics (OPVs) prepared from a UV‐crosslinkable semiconducting polymer (P2FBTT‐Br) and a nonfullerene acceptor (IEICO‐4F) via a green solvent process. The synthesized P2FBTT‐Br can be crosslinked by UV irradiation for 150 s and dissolved in 2‐methylanisole due to its asymmetric structure. In OPV performance and burn‐in loss tests performed at 75 °C or AM 1.5G Sun illumination for 90 h, UV‐crosslinked devices with PC₇₁BM show 9.2% power conversion efficiency (PCE) and better stability against burn‐in loss than pristine devices. The frozen morphology resulting from the crosslinking prevents lateral crystallization and aggregation related to morphological degradation. When IEICO‐4F is introduced in place of a fullerene‐based acceptor, the burn‐in loss due to thermal aging and light soaking is dramatically suppressed because of the frozen morphology and high miscibility of the nonfullerene acceptor (18.7% → 90.8% after 90 h at 75 °C and 37.9% → 77.5% after 90 h at AM 1.5G). The resulting crosslinked device shows 9.4% PCE (9.8% in chlorobenzene), which is the highest value reported to date for crosslinked active materials, in the first green processing approach.     

Significantly Enhancing the Efficiency of a New Light‐Harvesting Polymer with Alkylthio naphthyl Substituents Compared to Their Alkoxyl Analogs

In this work, a new benzo[1,2‐b:4,5‐b′]dithiophene (BDT) building block containing alkylthio naphthyl as a side chain is designed and synthesized, and the resulting polymer, namely PBDTNS‐BDD, shows a lower HOMO energy level than that of its alkoxyl naphthyl counterpart PBDTNO‐BDD. An optimized photovoltaic device using PBDTNS‐BDD as a donor exhibits power conversion efficiencies (PCE) of 8.70% and 9.28% with the fullerene derivative PC₇₁BM and the fullerene‐free small molecule ITIC as acceptors, respectively. Surprisingly, ternary blend devices based on PBDTNS‐BDD and two acceptors, namely PC₇₁BM and ITIC, shows a PCE of 11.21%, which is much higher than that of PBDTNO‐BDD based ternary devices (7.85%) even under optimized conditions.     

Highly Efficient Polymer Tandem Cells and Semitransparent Cells for Solar Energy

Highly efficient tandem and semitransparent (ST) polymer solar cells utilizing the same donor polymer blended with [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PC₆₁BM) and [6,6]‐phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM) as active layers are demonstrated. A high power conversion efficiency (PCE) of 8.5% and a record high open‐circuit voltage of 1.71 V are achieved for a tandem cell based on a medium bandgap polymer poly(indacenodithiophene‐co‐phananthrene‐quinoxaline) (PIDT‐phanQ). In addition, this approach can also be applied to a low bandgap polymer poly[2,6‐(4,4‐bis(2‐ethylhexyl)‐4H‐cyclopenta[2,1‐b;3,4‐b′]dithiophene)‐alt‐4,7‐(5‐fluoro‐2,1,3‐benzothia‐diazole)] (PCPDTFBT), and PCEs up to 7.9% are achieved. Due to the very thin total active layer thickness, a highly efficient ST tandem cell based on PIDT‐phanQ exhibits a high PCE of 7.4%, which is the highest value reported to date for a ST solar cell. The ST device also possesses a desirable average visible transmittance (≈40%) and an excellent color rendering index (≈100), permitting its use in power‐generating window applications.     

Layer‐by‐Layer Solution‐Processed Low‐Bandgap Polymer‐PC61BM Solar Cells with High Efficiency

Polymer solar cells (PSCs) are fabricated without solvent additives using a low‐bandgap polymer, PBDTTT‐C‐T, as the donor and [6,6]‐phenyl‐C61‐butyric‐acid‐methyl‐ester (PC₆₁BM) as the acceptor. Donor‐acceptor blend and layer‐by‐layer (LL) solution process are used to form active layers. Relative to the blend devices, the LL devices exhibit stronger absorption, better vertical phase separation, higher hole and electron mobilities, and better charge extraction at correct electrodes. As a result, after thermal annealing the LL devices exhibit an average power conversion efficiency (PCE) of 6.86%, which is much higher than that of the blend devices (4.31%). The best PCE of the LL devices is 7.13%, which is the highest reported for LL processed PSCs and among the highest reported for PC₆₁BM‐based single‐junction PSCs.     

From Binary to Ternary: Improving the External Quantum Efficiency of Small‐Molecule Acceptor‐Based Polymer Solar Cells with a Minute Amount of Fullerene Sensitization

Ternary blend is proved to be a potential contender for achieving high efficiency in organic photovoltaics, which can apparently strengthen the absorption of active layer so as to better harvest light irradiation. Much of the previous work in ternary polymer solar cells focuses on broadening the absorption spectrum; however, a new insight is brought to study the third component, which in tiny amounts influents the small‐molecule acceptor‐based device performance. Without contributing to complementing the absorption, a minute amount of fullerene derivative, Bis‐PC₇₀BM, can effectively play an impressive role as sensitizer in enhancing the external quantum efficiency of the host binary blend, especially for polymeric donor. Detailed investigations reveal that the minute addition of Bis‐PC₇₀BM can realize morphology modification as well as facilitate electron transfer from polymeric donor to small molecule acceptor via cascade energy level modulation, and therefore lead to an improvement in device efficiency.     

Influence of Fullerene Acceptor on the Performance,Microstructure, and Photophysics of Low Bandgap Polymer Solar Cells

The morphology, photophysics, and device performance of solar cells based on the low bandgap polymer poly[[2,6′‐4,8‐di(5‐ethylhexylthienyl)benzo[1,2‐b;3,3‐b]dithiophene]3‐fluoro‐2[(2‐ethylhexyl)carbonyl]thieno[3,4‐b]thiophenediyl (PBDTTT‐EFT) (also known as PTB7‐Th) blended with different fullerene acceptors: Phenyl‐C₆₁‐butyric acid methyl ester (PC₆₁BM), phenyl‐C₇₁ ‐butyric acid methyl ester (PC₇₁BM), or indene‐C₆₀ bisadduct (ICBA) are correlated. Compared to PC₇₁ BM‐based cells – which achieve a power conversion efficiency (PCE) of 9.4% – cells using ICBA achieve a higher open‐circuit voltage (V_OC) of 1.0 V albeit with a lower PCE of 7.1%. To understand the origin of this lower PCE, the morphology and photophysics have been thoroughly characterized. Hard and soft X‐ray scattering measurements reveal that the PBDTTT‐EFT:ICBA blend has a lower crystallinity, lower domain purity, and smaller domain size compared to the PBDTTT‐EFT:PC₇₁BM blend. Incomplete photoluminescence quenching is also found in the ICBA blend with transient absorption measurements showing faster recombination dynamics at short timescales. Transient photovoltage measurements highlight further differences in recombination at longer timeframes due to the more intermixed morphology of the ICBA blend. Interestingly, a mild thermal treatment improves the performance of PBDTTT‐EFT:ICBA cells which is exploited in the fabrication of a homo PBDTTT‐EFT:ICBA tandem solar cell with PCE of 9.0% and V_OC of 1.93 V.     

Manipulating Backbone Structure to Enhance Low Band Gap Polymer Photovoltaic Performance

A pair of polymers, PBDTBT and PBDTDTBT , was synthesized for application in polymer solar cells (PSCs). Although these two polymers have similar absorption bands and molecular energy levels, PBDTDTBT exhibits much better photovoltaic performance in polymer solar cell (PSC) devices with power conversion efficiency (PCE) of 7.4%. To understand the differences between PBDTDTBT and PBDTBT , we have investigated the correlations of the molecular structure, morphology, dynamics and efficiency of these two polymers. A theoretical investigation using density functional theory (DFT) and time‐dependent DFT (TDDFT) has been employed to investigate the electron density and electron delocalization extent of the unimers. TEM data showed that PBDTDTBT phase separates from PC₇₁BM, while PBDTBT suffers from having a proper morphology on different processing conditions. Grazing incidence wide angle X‐ray diffraction (GIWAXD) was used to probe the crystal structure of the polymers in thin film. A polymorph crystal structure was observed for PBDTBT . Grazing incidence small angle X‐ray scattering (GISAXS) was used to probe the size scale of phase separation, with an optimized 25 nm feature size observed for PBDTDTBT /PC₇₁BM blends, which agrees well with TEM results. Femtosecond transient absorption (TA) spectroscopy was used to probe the dynamics of the fundamental processes in organic photovoltaic (OPV) materials, such as charge separation and recombination. The enhanced absorption coefficient, good charge separation, optimal phase separation and higher charge mobility all contribute to the high PCE of the PBDTDTBT /PC₇₁BM devices.     

Investigation of Charge Carrier Behavior in High Performance Ternary Blend Polymer Solar Cells

This study demonstrates high‐performance, ternary‐blend polymer solar cells by modifying a binary blend bulk heterojunction (PPDT2FBT:PC₇₁BM) with the addition of a ternary component, PPDT2CNBT. PPDT2CNBT is designed to have complementary absorption and deeper frontier energy levels compared to PPDT2FBT, while being based on the same polymeric backbone. A power conversion efficiency of 9.46% is achieved via improvements in both short‐circuit current density (J_SC) and open‐circuit voltage (V_OC). Interestingly, the V_OC increases with increasing the PPDT2CNBT content in ternary blends. In‐depth studies using ultraviolet photoelectron spectroscopy and transient absorption spectroscopy indicate that the two polymers are not electronically homogeneous and function as discrete light harvesting species. The structural similarity between PPDT2CNBT and PPDT2FBT allows the merits of a ternary system to be fully utilized to enhance both J_SC and V_OC without detriment to fill‐factor via minimized disruption of semi‐crystalline morphology of binary PPDT2FBT:PC₇₁BM blend. Further, by careful analysis, charge carrier transport in this ternary blend is clearly verified to follow parallel‐like behavior.     

Impact of Fullerene on the Photophysics of Ternary Small Molecule Organic Solar Cells

Ternary organic solar cells (OSCs) are among the best‐performing organic photovoltaic devices to date, largely due to the recent development of nonfullerene acceptors. However, fullerene molecules still play an important role in ternary OSC systems, since, for reasons not well understood, they often improve the device performance, despite their lack of absorption. Here, the photophysics of a prototypical ternary small‐molecule OSC blend composed of the donor DR3, the nonfullerene acceptor ICC6, and the fullerene derivative PC₇₁BM is studied by ultrafast spectroscopy. Surprisingly, it is found that after excitation of PC₇₁BM, ultrafast singlet energy transfer to ICC6 competes efficiently with charge transfer. Subsequently, singlets on ICC6 undergo hole transfer to DR3, resulting in free charge generation. Interestingly, PC₇₁BM improves indirectly the electron mobility of the ternary blend, while electrons reside predominantly in ICC6 domains as indicated by fast spectroscopy. The improved mobility facilitates charge carrier extraction, in turn leading to higher device efficiencies of the ternary compared to binary solar cells. Using the (photo)physical parameters obtained from (transient) spectroscopy and charge transport measurements, the device's current–voltage characteristics are simulated and it is demonstrated that the parameters accurately reproduce the experimentally measured device performance.     

A Thieno[3,2‐c]Isoquinolin‐5(4H)‐One Building Block for Efficient Thick‐Film Solar Cells

An aromatic lactam acceptor unit, thieno[3,2‐c]isoquinolin‐5(4H)‐one (TIQ), is developed. Compared with its analogues, dithieno[3,2‐b:2′,3′‐d]pyridin‐5(4H)‐one (DTP) and phenanthridin‐6(5H)‐one (PN), TIQ shows its advantage in constructing donor–acceptor (D–A) copolymers for efficient solar cells. TIQ‐based D–A copolymer PTIQ4TFBT delivers a power conversion efficiency (PCE) of 10.16% in polymer:fullerene solar cells, while those based on DTP and PN copolymers, PDTP4TFBT and PPN4TFBT, afford PCEs around 8.5%. The higher performance of PTIQ4TFBT:PC₇₁BM solar cells originates from enhanced short‐circuit current density (J_sc) and fill factor (FF), because of favorable morphology, less bimolecular recombination, and balanced charge transport in the active layer. Moreover, the performance for PTIQ4TFBT:PC₇₁BM solar cells is less sensitive to active layer thickness than PDTP4TFBT:PC₇₁BM and PPN4TFBT:PC₇₁BM solar cells. Over 8% PCEs can be obtained from PTIQ4TFBT:PC₇₁BM solar cells when the active layer thickness is over 500 nm.     

Thermally Durable Nonfullerene Acceptor with Nonplanar Conjugated Backbone for High‐Performance Organic Solar Cells

A nonfullerene acceptor (NFA) with acceptor–donor–acceptor (A–D–A) architecture, i‐IEICO‐2F, based on 4,9‐dihydro‐s‐indaceno[1,2‐b:5,6‐b′]dithiophene as an electron‐donating core and 2‐(6‐fluoro‐2,3‐dihydro‐3‐oxo‐1H‐inden‐1‐ylidene)‐propanedinitrile as electron‐withdrawing end groups, is designed and synthesized. i‐IEICO‐2F has a twist structure in the main conjugated chain, which causes blueshifted absorption and leads to harmonious absorption with a high bandgap donor. The bandgap of i‐IEICO‐2F compliments the bandgap of suitable wide bandgap donor polymers such as J52, leading to complete light absorption throughout the visible spectrum. Devices based on i‐IEICO‐2F exhibit optimized photovoltaic performance including an open‐circuit voltage of 0.93 V, a short‐circuit current density of 16.61 mA cm^?2, and a fill factor of 73%, and result in a power conversion efficiency (PCE) of 11.28%. The i‐IEICO‐2F‐based devices reach PCEs of >11% without using any additives or post‐treatments. Devices are found to be thermally stable and maintain 44% of their initial PCE after 184.5 h of continuous thermal annealing (TA) treatment at 150 °C. Based on UV, atomic force microscopy (AFM), and grazing incidence wide angle X‐ray scattering (GIWAXS) results, i‐IEICO‐2F devices show almost identical morphology and molecular orientation throughout the TA treatment and excellent stability compared to other IEICO derivatives.     

Effect of Molecular Orientation of Donor Polymers on Charge Generation and Photovoltaic Properties in Bulk Heterojunction All‐Polymer Solar Cells

All‐polymer solar cells (all‐PSCs) utilizing p‐type polymers as electron‐donors and n ‐typepolymers as electron‐acceptors have attracted a great deal of attention, and their efficiencies have been improved considerably. Here, five polymer donors with different molecular orientations are synthesized by random copolymerization of 5‐fluoro‐2,1,3‐benzothiadiazole with different relative amounts of 2,2′‐bithiophene (2T) and dithieno[3,2‐b;2′,3′‐d]thiophene (DTT). Solar cells are prepared by blending the polymer donors with a naphthalene diimide‐based polymer acceptor (PNDI) or a [6,6]‐phenyl C₇₁‐butyric acid methyl ester (PC₇₁BM) acceptor and their morphologies and crystallinity as well as optoelectronic, charge‐transport and photovoltaic properties are studied. Interestingly, charge generation in the solar cells is found to show higher dependence on the crystal orientation of the donor polymer for the PNDI‐based all‐PSCs than for the conventional PC₇₁BM‐based PSCs. As the population of face‐on‐oriented crystallites of the donor increased in PNDI‐based PSC, the short‐circuit current density (J_SC) and external quantum efficiency of the devices are found to significantly improve. Consequently, device efficiency was enhanced of all‐PSC from 3.11% to 6.01%. The study reveals that producing the same crystal orientation between the polymer donor and acceptor (face‐on/face‐on) is important in all‐PSCs because they provide efficient charge transfer at the donor/acceptor interface.     

Ternary Organic Solar Cells with >11% Efficiency Incorporating Thick Photoactive Layer and Nonfullerene Small Molecule Acceptor

Currently, constructing ternary organic solar cells (OSCs) and developing nonfullerene small molecule acceptors (n‐SMAs) are two pivotal avenues to enhance the device performance. However, introducing n‐SMAs into the ternary OSCs to construct thick layer device is still a challenge due to their inferior charge transport property and unclear aggregation mechanism. In this work, a novel wide band gap copolymer 4,8‐bis(4,5‐dioctylthiophen‐2‐yl) benzo[1,2‐b:4,5‐b′]dithiophene‐2,6‐diyl‐alt‐N‐(2‐hexyldecyl)‐5,5′‐bis(thiophen‐2‐yl)‐2,2′‐bithiophene‐3,3′‐dicarboximide (PDOT) is designed and blend of PDOT:PC₇₁BM achieves a power conversion efficiency (PCE) of 9.5% with active layer thickness over 200 nm. The rationally selected n‐SMA based on a bulky seven‐ring fused core (indacenodithieno[3,2‐b]thiophene) end‐capped with 2‐(3‐oxo‐2,3‐dihydroinden‐1‐ylidene) malononitrile groups (ITIC) is introduced into the host binary PDOT:PC₇₁BM system to extend the absorption range and reduce the photo energy loss. After fully investigating the morphology evolution of the ternary blends, the different aggregation behavior of n‐SMAs with respect to their fullerene counterpart is revealed and the adverse effect of introducing n‐SMAs on charge transport is successfully avoided. The ternary OSC delivers a PCE of 11.2% with a 230 nm thick active layer, which is among the highest efficiencies of thick layer OSCs. The results demonstrate the feasibility of using n‐SMAs to construct a thick layer ternary device for the first time, which will greatly promote the efficiency of thick layer ternary devices.     

Favorable Mixing Thermodynamics in Ternary Polymer Blends for Realizing High Efficiency Plastic Solar Cells

Ternary blends with broad spectral absorption have the potential to increase charge generation in organic solar cells but feature additional complexity due to limited intermixing and electronic mismatch. Here, a model system comprising the polymers poly[5,5‐bis(2‐butyloctyl)‐(2,2‐bithiophene)‐4,4‐dicarboxylate‐alt‐5,5‐2,2‐bithiophene] (PDCBT) and PTB7‐Th and PC₇₀BM as an electron accepting unit is presented. The power conversion efficiency (PCE) of the ternary system clearly surpasses the performance of either of the binary systems. The photophysics is governed by a fast energy transfer process from PDCBT to PTB7‐Th, followed by electron transfer at the PTB7‐Th:fullerene interface. The morphological motif in the ternary blend is characterized by polymer fibers. Based on a combination of photophysical analysis, GIWAXS measurements and calculation of the intermolecular parameter, the latter indicating a very favorable molecular affinity between PDCBT and PTB7‐Th, it is proposed that an efficient charge generation mechanism is possible because PTB7‐Th predominantly orients around PDCBT filaments, allowing energy to be effectively relayed from PDCBT to PTB7‐Th. Fullerene can be replaced by a nonfullerene acceptor without sacrifices in charge generation, achieving a PCE above 11%. These results support the idea that thermodynamic mixing and energetics of the polymer–polymer interface are critical design parameter for realizing highly efficient ternary solar cells with variable electron acceptors.     

Slot‐Die and Roll‐to‐Roll Processed Single Junction Organic Photovoltaic Cells with the Highest Efficiency

The record efficiency of the state‐of‐the‐art polymer solar cells (PSCs) is rapidly increasing, due to the discovery of high‐performance photoactive donor and acceptor materials. However, strong questions remain as to whether such high‐efficiency PSCs can be produced by scalable processes. This paper reports a high power conversion efficiency (PCE) of 13.5% achieved with single‐junction ternary PSCs based on PTB7‐Th, PC₇₁BM, and COi8DFIC fabricated by slot‐die coating, which shows the highest PCE ever reported in PSCs fabricated by a scalable process. To understand the origin of the high performance of the slot‐die coated device, slot‐die coated photoactive films and devices are systematically investigated. These results indicate that the good performance of the slot‐die PSCs can be due to a favorable molecule‐structure and film‐morphology change by introducing 1,8‐diiodooctane and heat treatment, which can lead to improved charge transport with reduced carrier recombination. The optimized condition is then used for the fabrication of large‐area modules and also for roll‐to‐roll fabrication. The slot‐die coated module with 30 cm² active‐area and roll‐to‐roll produced flexible PSC has shown 8.6% and 9.6%, respectively. These efficiencies are the highest in each category and demonstrate the strong potential of the slot‐die coated ternary system for commercial applications.     

Efficient Ternary Polymer Solar Cells with Two Well‐Compatible Donors and One Ultranarrow Bandgap Nonfullerene Acceptor

Nonfullerene polymer solar cells (PSCs) are fabricated by using one wide bandgap donor PBDB‐T and one ultranarrow bandgap acceptor IEICO‐4F as the active layers. One medium bandgap donor PTB7‐Th is selected as the third component due to the similar highest occupied molecular orbital level compared to that of PBDB‐T and their complementary absorption spectra. The champion power conversion efficiency (PCE) of PSCs is increased from 10.25% to 11.62% via incorporating 20 wt% PTB7‐Th in donors, with enhanced short‐circuit current (J_SC) of 24.14 mA cm^?2 and fill factor (FF) of 65.03%. The 11.62% PCE should be the highest value for ternary nonfullerene PSCs. The main contribution of PTB7‐Th can be summarized as the improved photon harvesting and enhanced exciton utilization of PBDB‐T due to the efficient energy transfer from PBDB‐T to PTB7‐Th. Meanwhile, PTB7‐Th can also act as a regulator to adjust PBDB‐T molecular arrangement for optimizing charge transport, resulting in the enhanced FF of ternary PSCs. This experimental result may provide new insight for developing high‐performance ternary nonfullerene PSCs by selecting two well‐compatible donors with different bandgap and one ultranarrow bandgap acceptor.     

Work Function Control of Interfacial Buffer Layers for Efficient and Air‐Stable Inverted Low‐Bandgap Organic Photovoltaics

A water‐soluble cationic polythiophene derivative, poly[3‐(6‐{4‐tert‐butylpyridiniumyl}‐hexyl)thiophene‐2,5‐diyl] [P3(TBP)HT], is combined with anionic poly(3,4‐ethylenedioxythiophene):poly(p‐styrenesulfonate) (PEDOT:PSS) on indium tin oxide (ITO) substrates via electrostatic layer‐by‐layer (eLbL) assembly. By varying the number of eLbL layers, the electrode's work function is precisely controlled from 4.6 to 3.8 eV. These polymeric coatings are used as cathodic interfacial modifiers for inverted‐mode organic photovoltaics that incorporate a photoactive layer composed of either poly[(3‐hexylthiophene)‐2,5‐diyl] (P3HT) and the fullerene acceptor [6,6‐phenyl‐C₆₁‐butyric acid methyl ester (PC₆₁BM) or the low bandgap polymer [poly({4,8‐di(2‐ethylhexyloxyl)benzo[1,2‐b:4,5‐b′]dithiophene}‐2,6‐diyl)‐alt‐({5‐octylthieno[3,4‐c]pyrrole‐4,6‐dione}‐1,3‐diyl) (PBDTTPD)] and the electron acceptor [6,6‐phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM)]. The power conversion efficiency (PCE) of the resulting photovoltaic device is dependent on the composition of the eLbL‐assembled interface and permits the fabrication of devices with efficiencies of 3.8% and 5.6% for P3HT and PBDTTPD donor polymers, respectively. Notably, these devices demonstrate significant stability with a P3HT:PC₆₁BM system maintaining 83% of its original PCE after 1 year of storage and a PBDTTPD:PC₇₁BM system maintaining 97% of its original PCE after over 1000 h of storage in air, according to the ISOS‐D‐1 shelf protocol.     

Synergic Interface and Optical Engineering for High‐Performance Semitransparent Polymer Solar Cells

In this study the thickness of the PTB7‐Th:PC₇₁BM bulk heterojunction (BHJ) film and the PF3N‐2TNDI electron transport layer (ETL) is systematically tuned to achieve polymer solar cells (PSCs) with optimized power conversion efficiency (PCE) of over 9% when an ultrathin BHJ of 50 nm is used. Optical modeling suggests that the high PCE is attributed to the optical spacer effect from the ETL, which not only maximizes the optical field within the BHJ film but also facilitates the formation of a more homogeneously distributed charge generation profile across the BHJ film. Experimentally it is further proved that the extra photocurrent produced at the PTB7‐Th/PF3N‐2TNDI interface also contributes to the improved performance. Taking advantage of this high performance thin film device structure, one step further is taken to fabricate semitransparent PSCs (ST‐PSCs) by using an ultrathin transparent Ag cathode to replace the thick Ag mirror cathode, yielding a series of high performance ST‐PSCs with PCEs over 6% and average visible transmittance between 20% and 30%. These ST‐PSCs also possess remarkable transparency color perception and rendering properties, which are state‐of‐the‐art and fulfill the performance criteria for potential use as power‐generating windows in near future.