Production of <Emphasis Type="SmallCaps">l</Emphasis>-phenylalanine from glycerol by a recombinant <Emphasis Type="Italic">Escherichia coli</Emphasis>

The production of l-phenylalanine is conventionally carried out by fermentations that use glucose or sucrose as the carbon source. This work reports on the use of glycerol as an inexpensive and abundant sole carbon source for producing l-phenylalanine using the genetically modified bacterium Escherichia coli BL21(DE3). Fermentations were carried out at 37°C, pH 7.4, using a defined medium in a stirred tank bioreactor at various intensities of impeller agitation speeds (300–500 rpm corresponding to 0.97–1.62 m s⁻¹ impeller tip speed) and aeration rates (2–8 L min⁻¹, or 1–4 vvm). This highly aerobic fermentation required a good supply of oxygen, but intense agitation (impeller tip speed ~1.62 m s⁻¹) reduced the biomass and l-phenylalanine productivity, possibly because of shear sensitivity of the recombinant bacterium. Production of l-phenylalanine was apparently strongly associated with growth. Under the best operating conditions (1.30 m s⁻¹ impeller tip speed, 4 vvm aeration rate), the yield of l-phenylalanine on glycerol was 0.58 g g⁻¹, or more than twice the best yield attainable on sucrose (0.25 g g⁻¹). In the best case, the peak concentration of l-phenylalanine was 5.6 g L⁻¹, or comparable to values attained in batch fermentations that use glucose or sucrose. The use of glycerol for the commercial production of l-phenylalanine with E. coli BL21(DE3) has the potential to substantially reduce the cost of production compared to sucrose- and glucose-based fermentations.     

Alginate production and <Emphasis Type="Italic">alg8</Emphasis> gene expression by <Emphasis Type="Italic">Azotobacter vinelandii</Emphasis> in continuous cultures

Alginates are polysaccharides that are used as thickening agents, stabilizers, and emulsifiers in various industries. These biopolymers are produced by fermentation with a limited understanding of the processes occurring at the cellular level. The objective of this study was to evaluate the effects of agitation rate and inlet sucrose concentrations (ISC) on alginate production and the expression of the genes encoding for alginate-lyases (algL) and the catalytic subunit of the alginate polymerase complex (alg8) in chemostat cultures of Azotobacter vinelandii ATCC 9046. Increased alginate production (2.4 g l⁻¹) and a higher specific alginate production rate (0.1 g g⁻¹ h⁻¹) were obtained at an ISC of 15 g l⁻¹. Carbon recovery of about 100% was obtained at an ISC of 10 g l⁻¹, whereas it was close to 50% at higher ISCs, suggesting that cells growing at lower sucrose feed rates utilize the carbon source more efficiently. In each of the steady states evaluated, an increase in algL gene expression was not related to a decrease in alginate molecular weight, whereas an increase in the molecular weight of alginate was linked to higher alg8 gene expression, demonstrating a relationship between the alg8 gene and alginate polymerization in A. vinelandii for the first time. The results obtained provide a possible explanation for changes observed in the molecular weight of alginate synthesized and this knowledge can be used to build a recombinant strain able to overexpress alg8 in order to produce alginates with higher molecular weights.     

<Emphasis Type="Italic">Clostridium beijerinckii</Emphasis> mutant with high inhibitor tolerance obtained by low-energy ion implantation

Clostridium beijerinckii mutant strain IB4, which has a high level of inhibitor tolerance, was screened by low-energy ion implantation and used for butanol fermentation from a non-detoxified hemicellulosic hydrolysate of corn fiber treated with dilute sulfuric acid (SAHHC). Evaluation of toxicity showed C. beijerinckii IB4 had a higher level of tolerance than parent strain C. beijerinckii NCIMB 8052 for five out of six phenolic compounds tested (the exception was vanillin). Using glucose as carbon source, C. beijerinckii IB4 produced 9.1 g l⁻¹ of butanol with an acetone/butanol/ethanol (ABE) yield of 0.41 g g⁻¹. When non-detoxified SAHHC was used as carbon source, C. beijerinckii NCIMB 8052 grew well but ABE production was inhibited. By contrast, C. beijerinckii IB4 produced 9.5 g l⁻¹ of ABE with a yield of 0.34 g g⁻¹, including 2.2 g l⁻¹ acetone, 6.8 g l⁻¹ butanol, and 0.5 g l⁻¹ ethanol. The remarkable fermentation and inhibitor tolerance of C. beijerinckii IB4 appears promising for ABE production from lignocellulosic materials.     

<Emphasis Type="Italic">Agrobacterium</Emphasis><Emphasis Type="Italic">tumefaciens</Emphasis>-mediated transformation of callus cells of <Emphasis Type="Italic">Crataegus</Emphasis><Emphasis Type="Italic">aronia</Emphasis>

A genetic transformation system has been developed for callus cells of Crataegus aronia using Agrobacterium tumefaciens. Callus culture was established from internodal stem segments incubated on Murashige and Skoog (MS) medium supplemented with 5 mg l⁻¹ Indole-3-butyric acid (IBA) and 0.5 mg l⁻¹ 6-benzyladenine (BA). In order to optimize the callus culture system with respect to callus growth and coloration, different types and concentrations of plant growth regulators were tested. Results indicated that the best average fresh weight of red colored callus was obtained on MS medium supplemented with 2 mg l⁻¹ 2,4-dichlorophenoxyacetic acid (2,4-D) and 1.5 mg l⁻¹ kinetin (Kin) (callus maintenance medium). Callus cells were co-cultivated with Agrobacterium harboring the binary plasmid pCAMBIA1302 carrying the mgfp5 and hygromycin phosphotransferase (hptII) genes conferring green fluorescent protein (GFP) activity and hygromycin resistance, respectively. Putative transgenic calli were obtained 4 weeks after incubation of the co-cultivated explants onto maintenance medium supplemented with 50 mg l⁻¹ hygromycin. Molecular analysis confirmed the integration of the transgenes in transformed callus. To our knowledge, this is the first time to report an Agrobacterium-mediated transformation system in Crataegus aronia.     

Substrate specificity of a recombinant ribose-5-phosphate isomerase from <Emphasis Type="Italic">Streptococcus pneumoniae</Emphasis> and its application in the production of <Emphasis Type="SmallCaps">l</Emphasis>-lyxose and <Emphasis Type="SmallCaps">l</Emphasis>-tagatose

A putative ribose-5-phosphate isomerase (RpiB) from Streptococcus pneumoniae was purified with a specific activity of 26.7 U mg⁻¹ by Hi-Trap Q HP anion exchange and Sephacryl S-300 HR 16/60 gel filtration chromatographies. The native enzyme existed as a 96-kDa tetramer with activity maxima at pH 7.5 and 35°C. The RpiB exhibited isomerization activity with l-lyxose, l-talose, d-gulose, d-ribose, l-mannose, d-allose, l-xylulose, l-tagatose, d-sorbose, d-ribulose, l-fructose, and d-psicose and exhibited particularly high activity with l-form monosaccharides such as l-lyxose, l-xylulose, l-talose, and l-tagatose. With l-xylulose (500 g l⁻¹) and l-talose (500 g l⁻¹) substrates, the optimum concentrations of RpiB were 300 and 600 U ml⁻¹, respectively. The enzyme converted 500 g l⁻¹ l-xylulose to 350 g l⁻¹ l-lyxose after 3 h, and yielded 450 g l⁻¹ l-tagatose from 500 g l⁻¹ l-talose after 5 h. These results suggest that RpiB from S. pneumoniae can be employed as a potential producer of l-form monosaccharides.     

Elicitation of guggulsterone production in cell cultures of <Emphasis Type="Italic">Commiphora wightii</Emphasis> by plant gums

Plant gum as an elicitor for guggulsterone production in cell cultures of Commiphora wightii is reported for the first time. Guggulsterone production increased 2.4 fold in the cell cultures by gum Arabic (100 mg l⁻¹), while mesquite gum elicited 2 fold. The cells treated with gum Arabic at 7th and 9th day accumulated enhanced guggulsterones within 24 h, which increased further up to 48 h and then declined. The cells treated at 9th day accumulated higher amount (218 μg l⁻¹) of guggulsterones after 48 h of elicitation as compared to cells treated at 7th day (164 μg l⁻¹). The optimized elicitation conditions were used in vessels of varying capacity where maximum yield of 285 μg l⁻¹ of guggulsterones was recorded in 3 l shake flasks. These experiments enabled highest guggulsterones yield in a short duration of 11 days in cell cultures of C. wightii.     

Growth retardants stimulate guggulsterone production in the presence of fungal elicitor in fed-batch cultures of <Emphasis Type="Italic">Commiphora wightii</Emphasis>

Guggulsterone, a hypolipidemic natural agent, is produced in resin canals of the plant Commiphora wightii. In this study, the stimulatory effects of growth retardants [ALAR (N,N-dimethylaminosuccinamic acid) and CCC (chlormequat chloride)] and fungal elicitor on guggulsterone accumulation in cell cultures of C. wightii are reported. CCC at 1 mg l⁻¹ enhanced guggulsterone content (~123 μg l⁻¹) when added on the fifth day after inoculation, while ALAR at 2.5 mg l⁻¹ increased guggulsterone content (~116 μg l⁻¹) when added on the tenth day. In a two-stage fed-batch process, combined treatment with fungal elicitor and growth retardant caused a significant increase (~353 μg l⁻¹) in guggulsterone content in cell cultures after 17 days of growth. This represents an approximately fivefold increase over the guggulsterone contents in initial cultures of this plant.     

<Emphasis Type="Italic">Agrobacterium</Emphasis>-mediated transformation of <Emphasis Type="Italic">indica</Emphasis> rice cv. ADT 43

A reproducible and highly efficient protocol for Agrobacterium tumefaciens-mediated transformation of indica rice (Oryza sativa L. subsp. indica cv. ADT 43) was established. Prior to transformation, embryogenic callus were induced from mature seeds incubated on Linsmaier and Skoog (LS) medium supplemented with 2.5 mg l⁻¹ 2,4-dichlorophenoxyacetic acid (2,4-D) and 1.0 mg l⁻¹ thiamine-HCl. Callus, intact mature seeds, and other in vitro derived explants (leaf bases, leaf blades, coleoptiles, and root-tips) were immersed in a bacterial suspension culture of A. tumefaciens strain EHA 105, OD600 of 0.8, and co-cultivated on LS medium for 2 days in the dark at 25 ± 2°C. Based on GUS expression analysis, 10 min incubation time of explants on a co-cultivation medium containing 100 μM acetosyringone was optimum. Following β-glucuronidase (GUS) assay and polymerase chain reaction (PCR) analysis, transformants were identified. Stable integration of the transgene was confirmed in four putatively transformed T₀ plants by Southern blot analysis. The copy number of the transgene in these lines, one to two, was then determined. Among the observations made, necrosis of co-cultivated explants was a problem, as well as sensitivity of callus to Agrobacterium infection. Levels of necrosis could be minimized following co-cultivation of explants in a medium consisting of 30% LS and containing 10 g l⁻¹ (14), polyvinyl pyrrolidone, 10% coconut water, and 250 mg l⁻¹ timentin (15:1). This latter medium also increased the final transformation efficiency to 15.33%.     

Enhanced <Emphasis Type="SmallCaps">d</Emphasis>-ribose biosynthesis in batch culture of a transketolase-deficient <Emphasis Type="Italic">Bacillus subtilis</Emphasis> strain by citrate

In this study, the effects of citrate addition on d-ribose production were investigated in batch culture of a transketolase-deficient strain, Bacillus subtilis EC2, in shake flasks and bioreactors. Batch cultures in shake flasks and a 5-l reactor indicated that supplementation with 0.2–0.5 g l⁻¹ of citrate enhanced d-ribose production. When B. subtilis EC2 was cultivated in a 15-l reactor in a complex medium, the d-ribose concentration was 70.9 g l⁻¹ with a ribose yield of 0.497 mol mol⁻¹. When this strain was grown in the same medium supplemented with 0.3 g l⁻¹ of citrate, 83.4 g l⁻¹ of d-ribose were obtained, and the ribose yield was increased to 0.587 mol mol⁻¹. Addition of citrate reduced the activities of pyruvate kinase and phosphofructokinase, while it increased those of glucose-6-phosphate dehydrogenase and 6-phosphogluconate dehydrogenase. Metabolic flux distribution in the stationary phase indicated that citrate addition resulted in increased fluxes in the pentose phosphate pathway and TCA cycle, and decreased fluxes in the glycolysis and acetate pathways.     

Insecticide-tolerant and plant growth promoting <Emphasis Type="Italic">Bradyrhizobium</Emphasis> sp. (<Emphasis Type="Italic">vigna</Emphasis>) improves the growth and yield of greengram [<Emphasis Type="Italic">Vigna radiata</Emphasis> (L.) Wilczek] in insecticide-stressed soils

This study was designed to identify rhizobial strains specific to greengram expressing higher tolerance against insecticides, fipronil and pyriproxyfen, and synthesizing plant growth regulators even amid insecticide-stress. Of the 50 bradyrhizobial isolates, the Bradyrhizobium sp. strain MRM6 showed tolerance up to 1,600 μg mL⁻¹ against each of fipronil and pyriproxyfen. The tolerant Bradyrhizobium sp. (vigna) produced plant growth promoting substances in substantial amounts, both in the presence and absence of insecticides. The strain MRM6 was further used to investigate its impact on greengram grown in soils treated with 200 (the recommended dose), 400 and 600 μg kg⁻¹ soil of fipronil and 1,300 (the recommended dose), 2,600 and 3,900 μg kg⁻¹ soil of pyriproxyfen. Fipronil at 600 μg kg⁻¹ soils and pyriproxyfen at 3,900 μg kg⁻¹ soils had greatest toxic effects and decreased plant biomass, symbiotic efficiency, nutrient uptake and seed yield of greengram plants. The Bradyrhizobium sp. (vigna) inoculant when used with fipronil and pyriproxyfen significantly increased the measured parameters compared to the plants grown in soils treated solely with the same concentration of each insecticide. This study inferred that the Bradyrhizobium sp. (vigna) strain MRM6 may be exploited as bio-inoculant to increase the productivity of greengram exposed to insecticide-stressed soils.     

Improved clonal propagation of <Emphasis Type="Italic">Spilanthes</Emphasis><Emphasis Type="Italic">acmella</Emphasis> Murr. for production of scopoletin

A reproducible protocol for clonal propagation of Spilanthes acmella has been established. Routinely, the cultures were established in spring (January–April) season because of the highest aseptic culture establishment and high frequency shoot proliferation. Incorporation of 5 μM N⁶-benzyladenine (BA) to Murashige and Skoog (MS) basal medium showed 100% bud-break and promoted multiple shoot proliferation in cultures. Interestingly, a higher concentration of BA (7–15 μM) promoted stunted shoots with pale leaves while a lower concentration (1–3 μM) resulted in shoots with long internodes and excessive adventitious root proliferation from all over their surface. For recurrent shoot multiplication, single node segments from in vitro-developed shoots were excised and cultured on MS + BA (5 μM) medium where 20.3-fold shoot multiplication was achieved every 5 weeks. Finally, these shoots were successfully rooted on half-strength MS medium (major salts reduced to half-strength) with 50 g l⁻¹ sucrose, with a frequency of 100%. Transplantation survival of micropropagated plants was 88.9%. Additionally, accumulation of scopoletin, a phytoalexin, was revealed for the first time in the uninfected leaves of Spilanthes. Further, the quantitative estimation by HPLC with a fluorescence detector showed that the amounts of scopoletin content (0.10 μg g⁻¹ DW) in the leaves of micropropagated plants are comparable to those of field-grown mother plants. The study thus signifies the effectiveness of in vitro methodology for true-to-type plant regeneration of Spilanthes and their later utility for biosynthesis and constant production of scopoletin throughout the year.     

Drought,warming and soil fertilization effects on leaf volatile terpene concentrations in <Emphasis Type="Italic">Pinus halepensis</Emphasis> and <Emphasis Type="Italic">Quercus ilex</Emphasis>

The changes in foliar concentrations of volatile terpenes in response to water stress, fertilization and temperature were analyzed in Pinus halepensis and Quercus ilex. The most abundant terpenes found in both species were α-pinene and Δ³-carene. β-Pinene and myrcene were also abundant in both species. P. halepensis concentrations were much greater than those of Q. ilex in agreement with the lack of storage in the latter species (15205.60 ± 1140.04 vs. 0.54 ± 0.08 μg g⁻¹ [d.m.]). The drought treatment (reduction to 1/3 of full watering) significantly increased the total terpene concentrations in both species (54% in P. halepensis and 119% in Q. ilex). The fertilization treatment (addition of either 250 kg N ha⁻¹ or 250 kg P ha⁻¹ or both) had no significant effects on terpene foliar concentrations. The terpene concentrations increased from 0.25 μg g⁻¹ [d.m.] at 30°C to 0.70 μg g⁻¹ [d.m.] at 40°C in Q. ilex (the non-storing species) and from 2,240 μg g⁻¹ [d.m.] at 30°C to 15,621 μg g⁻¹ [d.m.] at 40°C in P. halepensis (the storing species). Both species presented negative relationship between terpene concentrations and relative water contents (RWC). The results of this study show that higher terpene concentrations can be expected in the warmer and drier conditions predicted for the next decades in the Mediterranean region.     

Succinic acid production from sugarcane bagasse hemicellulose hydrolysate by <Emphasis Type="Italic">Actinobacillus succinogenes</Emphasis>

Succinic acid, a four-carbon diacid, has been the focus of many research projects aimed at developing more economically viable methods of fermenting sugar-containing natural materials. Succinic acid fermentation processes also consume CO₂, thereby potentially contributing to reductions in CO₂ emissions. Succinic acid could also become a commodity used as an intermediate in the chemical synthesis and manufacture of synthetic resins and biodegradable polymers. Much attention has been given recently to the use of microorganisms to produce succinic acid as an alternative to chemical synthesis. We have attempted to maximize succinic acid production by Actinobacillus succinogenes using an experimental design methodology for optimizing the concentrations of the medium components. The first experiment consisted of a 2⁴⁻¹ fractional factorial design, and the second entailed a Central Composite Rotational Design so as to achieve optimal conditions. The optimal concentrations of nutrients predicted by the model were: NaHCO₃, 10.0 g l⁻¹; MgSO₄, 3.0 g l⁻¹; yeast extract, 2.0 g l⁻¹; KH₂PO₄. 5.0 g l⁻¹; these were experimentally validated. Under the best conversion conditions, as determined by statistical analysis, the production of succinic acid was carried out in an instrumented bioreactor using sugarcane bagasse hemicellulose hydrolysate, yielding a concentration of 22.5 g l⁻¹.     

Role of two contrasting ecosystem engineers (<Emphasis Type="Italic">Zostera noltii</Emphasis> and <Emphasis Type="Italic">Cymodocea nodosa</Emphasis>) on the food intake rate of <Emphasis Type="Italic">Cerastoderma edule</Emphasis>

Seagrasses are well known ecosystem engineers that can significantly influence local hydrodynamics and the abundance and biodiversity of macrobenthic organisms. This study focuses on the potential role of the seagrass canopy structure in altering the abundance of filter-feeding organisms by modifying the hydrodynamic driven food supply. We quantified the effect of two ecosystem engineers with contrasting canopy properties (i.e. Zostera noltii and Cymodocea nodosa) on the food intake rate of a suspension-feeding bivalve Cerastoderma edule living in these seagrass meadows. Field experiments were carried out in two seagrass beds (Z. noltii and C. nodosa) and bare sediment, located on sandflat characterised by a relatively high hydrodynamic energy from waves and currents. Results demonstrated that the filter-feeding rate was almost twofold increased when C. edule was inhabiting Z. noltii meadows (1.10 ± 0.24 μg Chl g Fresh Weight⁻¹) when compared to cockles living on the bare sediment (0.65 ± 0.14 μg Chl g FW⁻¹). Intermediate values were found within C. nodosa canopy (0.97 ± 0.24 μg Chl g FW⁻¹), but filter feeding rate showed no significant differences with values for Z. noltii meadows. There were no apparent correlations between canopy properties and filter-feeding rates. Our results imply that food refreshment within the seagrass canopies was enough to avoid food depletion. We therefore expect that the ameliorated environmental conditions within vegetated areas (i.e. lower hydrodynamic conditions, higher sediment stability, lower predation pressure…) in combination with sufficient food supply to prevent depletion within both canopies are the main factors underlying our observations.     

<Emphasis Type="SmallCaps">l</Emphasis>-Arabinose pathway engineering for arabitol-free xylitol production in <Emphasis Type="Italic">Candida tropicalis</Emphasis>

Xylose reductase (XR) is a key enzyme in biological xylitol production, and most XRs have broad substrate specificities. During xylitol production from biomass hydrolysate, non-specific XRs can reduce l-arabinose, which is the second-most abundant hemicellulosic sugar, to the undesirable byproduct arabitol, which interferes with xylitol crystallization in downstream processing. To minimize the flux from l-arabinose to arabitol, the l-arabinose-preferring, endogenous XR was replaced by a d-xylose-preferring heterologous XR in Candida tropicalis. Then, Bacillus licheniformis araA and Escherichia coli araB and araD were codon-optimized and expressed functionally in C. tropicalis for the efficient assimilation of l-arabinose. During xylitol fermentation, the control strains BSXDH-3 and KNV converted 9.9 g l-arabinose l⁻¹ into 9.5 and 8.3 g arabitol l⁻¹, respectively, whereas the recombinant strain JY consumed 10.5 g l-arabinose l⁻¹ for cell growth without forming arabitol. Moreover, JY produced xylitol with 42 and 16% higher productivity than BSXDH-3 and KNV, respectively.     

Increase of lycopene production by supplementing auxiliary carbon sources in metabolically engineered <Emphasis Type="Italic">Escherichia coli</Emphasis>

In the fed-batch culture of glycerol using a metabolically engineered strain of Escherichia coli, supplementation with glucose as an auxiliary carbon source increased lycopene production due to a significant increase in cell mass, despite a reduction in specific lycopene content. l-Arabinose supplementation increased lycopene production due to increases in cell mass and specific lycopene content. Supplementation with both glucose and l-arabinose increased lycopene production significantly due to the synergistic effect of the two sugars. Cell growth by the consumption of carbon sources was related to endogenous metabolism in the host E. coli. Supplementation with l-arabinose stimulated only the mevalonate pathway for lycopene biosynthesis and supplementation with both glucose and l-arabinose stimulated synergistically only the mevalonate pathway. In the fed-batch culture of glycerol with 10 g l⁻¹ glucose and 7.5 g l⁻¹ l-arabinose, the cell mass, lycopene concentration, specific lycopene content, and lycopene productivity after 34 h were 42 g l⁻¹, 1,350 mg l⁻¹, 32 mg g cells⁻¹, and 40 mg l⁻¹ h⁻¹, respectively. These values were 3.9-, 7.1-, 1.9-, and 11.7-fold higher than those without the auxiliary carbon sources, respectively. This is the highest reported concentration and productivity of lycopene.     

Evaluation of key factors influencing <Emphasis Type="Italic">Agrobacterium</Emphasis>-mediated transformation of somatic embryos of avocado (<Emphasis Type="Italic">Persea americana</Emphasis> Mill.)

Key factors influencing the efficiency of transformation of embryogenic cultures, induced from immature zygotic embryos, of avocado cv. ‘Duke 7’ were evaluated. Initially, the sensitivity of somatic embryos to the antibiotics kanamycin, used for selection, carbenicillin, cefotaxime and timentin, all used for elimination of Agrobacterium cells, were evaluated. Isolated globular somatic embryos were more sensitive to kanamycin than embryogenic masses, and 25 mg l⁻¹ kanamycin completely restricted callus proliferation. Cefotaxime at 500 mg l⁻¹ partially inhibited proliferation of embryogenic cultures, while both carbenicillin and timentin did not affect callus growth. For genetic transformation, somatic embryos were infected with A. tumefaciens containing the pBINUbiGUSint plasmid. After 2 days, the embryos were transferred to selection medium supplemented with 50 mg l⁻¹ kanamycin and 250 mg l⁻¹ timentin for 2 months. Then, kanamycin level was increased to 100 mg l⁻¹ for two additional months. The A. tumefaciens strain AGL1 yielded higher transformation rates, 6%, than EHA105 or LBA4404, 1.2%. The percentage of kanamycin resistant calli obtained was significantly influenced by the embryogenic line used as source of explants. Genetic transformation was confirmed by PCR and Southern blot analysis. A significant improvement in the germination rate was obtained when transgenic embryos were cultured in liquid MS medium with 4.44 μM BA and 2.89 μM GA₃ for 3 days in a roller drum and later transferred to the same medium gelled with 7 g l⁻¹ agar. Plants from five independent transgenic lines were acclimated and grown in the greenhouse, being phenotipically similar to control plants.     

Evaluation of methods for celery (<Emphasis Type="Italic">Apium Graveolens</Emphasis> L.) transformation using <Emphasis Type="Italic">Agrobacterium tumefaciens</Emphasis> and the <Emphasis Type="Italic">bar</Emphasis> gene as selectable marker

Callus selection (CS) and the flamingo-bill explant (FB) methods were evaluated for efficacy in transformation for celery. Agrobacterium tumefaciens strains EHA105 and GV3101, each with the bar gene under the promoters NOS (pGPTV-BAR) or 35S (pDHB321.1), were used. Leaf explants were inoculated and co-cultivated for 2 d in the dark. Calluses emerged on the explants on callus medium (C), Murashige and Skoog (MS) medium + 2,4-Dichlorophenoxyacetic acid (2,4-D) (2.3 μM) + kinetin (2.8 μM) + timentin (300 mg·l⁻¹). Calluses 4- to 6-wk-old were selected for glufosinate (GS) resistance by a two step method. First, calluses were transferred to C medium + GS 0.35, 0.5, 1, 2, 5, or 10 mg·l⁻¹; calluses formed only with 0, 0.35 and 0.5 mg·l⁻¹ GS. All growing calluses from 0 and 0.35 mg·l⁻¹ and a few from 0.5 mg·l⁻¹, were divided and placed back on C + GS 0.35–0.5 mg·l⁻¹ for another 5–6 wk. Second, tolerant clones were again divided and placed on C + GS 1–50 mg·l⁻¹. When cultivar XP85 was inoculated with both strains, using pGPTVBAR, 19 glufosinate resistant (GR) callus clones were selected, but shoots regenerated only for strain EHA105 inoculations. When both of the strains (each with pDHB321.1) were inoculated on cv. XP166, 3 and 12 GR calluses occurred for EHA105 and GV3101, respectively. Using CS, a total of 34 GR callus clones were selected, and shoots were regenerated from over 50% of them on Gamborg B5 medium + 6-(γ, γ-dimethylallylamino) purine 2ip (4.9 μM) + naphthaleneacetic acid (NAA; 1.6 μM) and rooted on MS in 5–6 mo total time. Conversely, using FB with inoculation by GV3101/pDHB321.1 on cv. XP166 yielded putative transgenic celery plants confirmed by polymerase chain reaction (PCR) in just 6 wk. Transformation of the bar gene into celery was confirmed by PCR for 5 and 6 CS and FB lines, respectively. Southern blot analyses indicated 1–2 copies in CS lines and 1 copy in FB lines. Herbicide assays on whole plants with 100 and 300 mg·l⁻¹ glufosinate indicated a range of low to high tolerance for lines derived by both methods. The bar gene was found to be Mendelian inherited in one self-fertile CS derived line.