Comparison of different pretreatment methods for lignocellulosic materials. Part I: conversion of rye straw to valuable products

The conversion of lignocellulose to valuable products requires I: a fractionation of the major components hemicellulose, cellulose, and lignin, II: an efficient method to process these components to higher valued products. The present work compares liquid hot water (LHW) pretreatment to the soda pulping process and to the ethanol organosolv pretreatment using rye straw as a single lignocellulosic material. The organosolv pretreated rye straw was shown to require the lowest enzyme loading in order to achieve a complete saccharification of cellulose to glucose. At biomass loadings of up to 15% (w/w) cellulose conversion of LHW and organosolv pretreated lignocellulose was found to be almost equal. The soda pulping process shows lower carbohydrate and lignin recoveries compared to the other two processes. In combination with a detailed analysis of the different lignins obtained from the three pretreatment methods, this work gives an overview of the potential products from different pretreatment processes.     

Dilute sulfuric acid cycle spray flow-through pretreatment of corn stover for enhancement of sugar recovery

A cycle spray flow-through reactor was designed and used to pretreat corn stover in dilute sulfuric acid medium. The dilute sulfuric acid cycle spray flow-through (DCF) process enhanced xylose sugar yields and cellulose digestibility while increasing the removal of lignin. Within the DCF system, the xylose sugar yields of 90–93% could be achieved for corn stover pretreated with 2% (w/v) dilute sulfuric acid at 95 °C during the optimal reaction time (90 min). The remaining solid residue exhibited enzymatic digestibility of 90–95% with cellulase loading of 60 FPU/g glucan that was due to the effective lignin removal (70–75%) in this process. Compared with flow-through and compress-hot water pretreatment process, the DCF method produces a higher sugar concentration and higher xylose monomer yield. The novel DCF process provides a feasible approach for lignocellulosic material pretreatment.     

BIOETHANOL PRODUCTION FROM LEAFY BIOMASS OF MANGO (Mangifera indica) INVOLVING NATURALLY ISOLATED AND RECOMBINANT ENZYMES

The present study describes the usage of dried leafy biomass of mango (Mangifera indica) containing 26.3% (w/w) cellulose, 54.4% (w/w) hemicellulose, and 16.9% (w/w) lignin, as a substrate for bioethanol production from Zymomonas mobilis and Candida shehatae. The substrate was subjected to two different pretreatment strategies, namely, wet oxidation and an organosolv process. An ethanol concentration (1.21 g/L) was obtained with Z. mobilis in a shake-flask simultaneous saccharification and fermentation (SSF) trial using 1% (w/v) wet oxidation pretreated mango leaves along with mixed enzymatic consortium of Bacillus subtilis cellulase and recombinant hemicellulase (GH43), whereas C. shehatae gave a slightly higher (8%) ethanol titer of 1.31 g/L. Employing 1% (w/v) organosolv pretreated mango leaves and using Z. mobilis and C. shehatae separately in the SSF, the ethanol titers of 1.33 g/L and 1.52 g/L, respectively, were obtained. The SSF experiments performed with 5% (w/v) organosolv-pretreated substrate along with C. shehatae as fermentative organism gave a significantly enhanced ethanol titer value of 8.11 g/L using the shake flask and 12.33 g/L at the bioreactor level. From the bioreactor, 94.4% (v/v) ethanol was recovered by rotary evaporator with 21% purification efficiency.     

A comparison of chemical pretreatment methods for improving saccharification of cotton stalks

The effectiveness of sulfuric acid (H(2)SO(4)), sodium hydroxide (NaOH), hydrogen peroxide (H(2)O(2)), and ozone pretreatments for conversion of cotton stalks to ethanol was investigated. Ground cotton stalks at a solid loading of 10% (w/v) were pretreated with H(2)SO(4), NaOH, and H(2)O(2) at concentrations of 0.5%, 1%, and 2% (w/v). Treatment temperatures of 90 degrees C and 121 degrees C at 15 psi were investigated for residence times of 30, 60, and 90 min. Ozone pretreatment was performed at 4 degrees C with constant sparging of stalks in water. Solids from H(2)SO(4), NaOH, and H(2)O(2) pretreatments (at 2%, 60 min, 121 degrees C/15 psi) showed significant lignin degradation and/or high sugar availability and hence were hydrolyzed by Celluclast 1.5L and Novozym 188 at 50 degrees C. Sulfuric acid pretreatment resulted in the highest xylan reduction (95.23% for 2% acid, 90 min, 121 degrees C/15 psi) but the lowest cellulose to glucose conversion during hydrolysis (23.85%). Sodium hydroxide pretreatment resulted in the highest level of delignification (65.63% for 2% NaOH, 90 min, 121 degrees C/15 psi) and cellulose conversion (60.8%). Hydrogen peroxide pretreatment resulted in significantly lower (p相似文献   

Ethanol production from seaweed (Undaria pinnatifida) using yeast acclimated to specific sugars

Ethanol production from Undaria pinnatifida (Sea mustard, Miyuk) was performed using yeast acclimated to specific sugars. Pretreatment conditions were optimized by thermal acid hydrolysis and enzyme treatment to increase the monosaccharide yield. Pretreatment by thermal acid hydrolysis was carried out using seaweed powder at 8 ～ 17% (w/v) solid content with a treatment time of 30 ～ 60 min. Enzyme treatment was carried out with 1% (v/v) Viscozyme L (1.2 FGU/mL), 1% (v/v) Celluclast 1.5 L (8.5 EGU/mL), 1% (v/v) AMG 300 L (3.0 AGU/mL), and 1% (v/v) Termamyl 120 L (0.72 KNU/mL). All enzymes except Termamyl 120 L, which was applied during pretreatment, were treated at 45°C for 24 h following pretreatment. Optimal pretreatment and enzyme conditions were determined to be 75 mM H₂SO₄, 13% (w/v) slurry, and 2.88 KNU/mL Termamyl 120 L at 121°C for 60 min. A maximum monosaccharide concentration of 33.1 g/L with 50.1% theoretical yield was obtained. To increase the ethanol yield, Pichia angophorae KCTC 17574 was acclimated to a high concentration (120 g/L) of galactose and mannitol at 30oC for 24 h. Ethanol production of 12.98 g/L with 40.12% theoretical yield was obtained from U. pinnatifida through fermentation with 0.35 g dry cell weight/L P. angophorae KCTC 17574 acclimated to mannitol and galactose.     

Production of isoprene,one of the high-density fuel precursors,from peanut hull using the high-efficient lignin-removal pretreatment method

Background

Isoprene as the feedstock can be used to produce renewable energy fuels, providing an alternative to replace the rapidly depleting fossil fuels. However, traditional method for isoprene production could not meet the demands for low-energy consumption and environment-friendliness. Moreover, most of the previous studies focused on biofuel production out of lignocellulosic materials such as wood, rice straw, corn cob, while few studies concentrated on biofuel production using peanut hull (PH). As is known, China is the largest peanut producer in the globe with an extremely considerable amount of PH to be produced each year. Therefore, a novel, renewable, and environment-friendly pretreatment strategy to increase the enzymatic hydrolysis efficiency of cellulose and reduce the inhibitors generation was developed to convert PH into isoprene.

Results

The optimal pretreatment conditions were 100 °C, 60 min, 10% (w/v) solid loading with a 2:8 volume ratio of phosphoric acid and of hydrogen peroxide. In comparison with the raw PH, the hemicellulose and lignin were reduced to 85.0 and 98.0%, respectively. The cellulose–glucose conversion of pretreated PH reached up to 95.0% in contrast to that of the raw PH (19.1%). Only three kinds of inhibitors including formic acid, levulinic acid, and a little furfural were formed during the pretreatment process, whose concentrations were too low to inhibit the isoprene yield for Escherichia coli fermentation. Moreover, compared with the isoprene yield of pure glucose fermentation (298 ± 9 mg/L), 249 ± 6.7 and 294 ± 8.3 mg/L of isoprene were produced using the pretreated PH as the carbon source by the engineered strain via separate hydrolysis and fermentation and simultaneous saccharification and fermentation (SSF) methods, respectively. The isoprene production via SSF had a 9.8% glucose–isoprene conversion which was equivalent to 98.8% of isoprene production via the pure glucose fermentation.

Conclusions

The optimized phosphoric acid/hydrogen peroxide combination pretreatment approach was proved effective to remove lignin and hemicellulose from lignocellulosic materials. Meanwhile, the pretreated PH could be converted into isoprene efficiently in the engineered Escherichia coli. It is concluded that this novel strategy of isoprene production using lignocellulosic materials pretreated by phosphoric acid/hydrogen peroxide is a promising alternative to isoprene production using traditional way which can fully utilize non-renewable fossil sources.

     

Biorefining of softwoods using ethanol organosolv pulping: preliminary evaluation of process streams for manufacture of fuel-grade ethanol and co-products

Pulps with residual lignin ranging from 6.4-27.4% (w/w) were prepared from mixed softwoods using a proprietary biorefining technology (the Lignol process) based on aqueous ethanol organosolv extraction. The pulps were evaluated for bioconversion using enzymatic hydrolysis of the cellulose fraction to glucose and subsequent fermentation to ethanol. All pulps were readily hydrolyzed without further delignification. More than 90% of the cellulose in low lignin pulps (< or =18.4% residual lignin) was hydrolyzed to glucose in 48 h using an enzyme loading of 20 filter paper units/g cellulose. Cellulose in a high lignin pulp (27.4% residual lignin) was hydrolyzed to >90% conversion within 48 h using 40 filter paper units/g. The pulps performed well in both sequential and simultaneous saccharification and fermentation trials indicating an absence of metabolic inhibitors. Chemical and physical analyses showed that lignin extracted during organosolv pulping of softwood is a suitable feedstock for production of lignin-based adhesives and other products due to its high purity, low molecular weight, and abundance of reactive groups. Additional co-products may be derived from the hemicellulose sugars and furfural recovered from the water-soluble stream.     

Mild pretreatment of yellow poplar biomass using sequential dilute acid and enzymatically-generated peracetic acid to enhance cellulase accessibility

Biomass contains cellulose, xylan and lignin in a complex interwoven structure that hinders enzymatic hydrolysis of the cellulose. To separate these components in yellow poplar biomass, we sequentially pretreated with dilute sulfuric acid and enzymatically-generated peracetic acid. In the first step, the dilute acid with microwave heating (140°C, 5 min) hydrolyzed 90% of xylan. The xylose yield in hydrolysate after dilute acid pretreatment was 83.1%. In the second step, peracetic acid (60°C, 6 h) removed up to 80% of lignin. This sequential pretreatment fractionated biomass into xylan and lignin, leaving a solid residue enriched in cellulose (~80%). The sequential pretreatment enhanced enzymatic digestibility of the cellulase by removal of the other components in biomass. The glucose yield after enzymatic hydrolysis was 90.5% at a low cellulase loading (5 FPU/g of glucan), which is 1.6 and 18 times higher than for dilute acid-pretreated biomass and raw biomass, respectively. This novel sequential pretreatment with dilute acid and peracetic acid efficiently separates the three major components of yellow poplar biomass, and reduces the amount of cellulase needed.     

Simultaneous saccharification and fermentation of acid-pretreated rapeseed meal for succinic acid production using Actinobacillus succinogenes

Rapeseed meal was evaluated for succinic acid production by simultaneous saccharification and fermentation using Actinobacillus succinogenes ATCC 55618. Diluted sulfuric acid pretreatment and subsequent hydrolysis with pectinase was used to release sugars from rapeseed meal. The effects of culture pH, pectinase loading and yeast extract concentration on succinic acid production were investigated. When simultaneous saccharification and fermentation of diluted acid pretreated rapeseed meal with a dry matter content of 12.5% (w/v) was performed at pH 6.4 and a pectinase loading of 2% (w/w, on dry matter) without supplementation of yeast extract, a succinic acid concentration of 15.5 g/L was obtained at a yield of 12.4 g/100g dry matter. Fed-batch simultaneous saccharification and fermentation was carried out with supplementation of concentrated pretreated rapeseed meal and pectinase at 18 and 28 h to yield a final dry matter content of 20.5% and pectinase loading of 2%, with the succinic acid concentration enhanced to 23.4 g/L at a yield of 11.5 g/100g dry matter and a productivity of 0.33 g/(Lh). This study suggests that rapeseed meal may be an alternative substrate for the efficient production of succinic acid by A. succinogenes without requiring nitrogen source supplementation.     

Fractionation of wheat straw by atmospheric acetic acid process

Fractionation of wheat straw was investigated using an atmospheric acetic acid process. Under the typical conditions of 90% (v/v) aqueous AcOH, 4% H(2)SO(4) (w/w, on straw), ratio of liquor to straw (L/S) 10 (v/w), pulping temperature 105 degrees C, and pulping time 3h, wheat straw was fractionated to pulp (cellulose), lignin and monosaccharides mainly from hemicellulose with yields of approximately 50%, 15% and 35%, respectively. Acetic acid pulp from the straw had an acceptable strength for paper and could be bleached to a high brightness over 85% with a short bleaching sequence. Acetic acid pulp was also a potential feedstock for fuels and chemicals. The acetic acid process separated pentose and hexose in wheat straw to a large extent. Most of the pentose (xylan) was dissolved, whereas the hexose (glucan) remained in the pulp. Approximately 30% of carbohydrates in wheat straw were hydrolyzed to monosaccharides during acetic acid pulping, of which xylose accounted for 70% and glucose for 12%. The acetic acid lignin from wheat straw showed relatively lower molecular weight and fusibility, which made the lignin a promising raw material for many products, such as adhesive and molded products.     

Isolation and characterisation of cellulose obtained by a two-stage treatment with organosolv and cyanamide activated hydrogen peroxide from wheat straw

Seven wheat straw cellulose preparations were isolated by a two-stage acidic organosolv treatment followed by cyanamide activated hydrogen peroxide bleaching. The effects of concentration of acetic and formic acids on the yield of cellulose and degradation of lignin and non-cellulose polysaccharides were investigated. Organic acids were more effective than alcohols on the degradation of lignin and hemicelluloses. Formic acid/acetic acid/water (30/60/10, v/v/v) system was found to be the most effective in delignification and removal of non-cellulose polysaccharides from the straw and did not have any undesirable effects on cellulose properties such as its intrinsic viscosity. In this case, the treatment removed 94.1% of the original lignin and 76.5% of the original hemicelluloses using 0.1% HCl as a catalyst at 85 °C for 4 h. Cyanamide activated hydrogen peroxide bleaching degraded substantial amounts of residual hemicelluloses and lignin, produced the cellulose samples having a relatively high purity. Under a best condition, a cellulose relatively free of lignin (0.7%) and with intrinsic viscosity of 393 ml g⁻¹ and favourable molar mass (213,940 g mol⁻¹) was obtained. Both unbleached and bleached cellulose preparations were further characterised by FT-IR and CP/MAS ¹³C NMR spectroscopy, and thermal stability.     

Bioethanol production from tension and opposite wood of <Emphasis Type="Italic">Eucalyptus globulus</Emphasis> using organosolv pretreatment and simultaneous saccharification and fermentation

During tree growth, hardwoods can initiate the formation of tension wood, which is a strongly stressed wood on the upper side of the stem and branches. In Eucalyptus globulus, tension wood presents wider and thicker cell walls with low lignin, similar glucan and high xylan content, as compared to opposite wood. In this work, tension and opposite wood of E. globulus trees were separated and evaluated for the production of bioethanol using ethanol/water delignification as pretreatment followed by simultaneous saccharification and fermentation (SSF). Low residual lignin and high glucan retention was obtained in organosolv pulps of tension wood as compared to pulps from opposite wood at the same H-factor of reaction. The faster delignification was associated with the low lignin content in tension wood, which was 15% lower than in opposite wood. Organosolv pulps obtained at low and high H-factor (3,900 and 12,500, respectively) were saccharified by cellulases resulting in glucan-to-glucose yields up to 69 and 77%, respectively. SSF of the pulps resulted in bioethanol yields up to 35 g/l that corresponded to 85–95% of the maximum theoretical yield on wood basis, considering 51% the yield of glucose to ethanol conversion in fermentation, which could be considered a very satisfactory result compared to previous studies on the conversion of organosolv pulps from hardwoods to bioethanol. Both tension and opposite wood of E. globulus were suitable raw materials for organosolv pretreatment and bioethanol production with high conversion yields.     

Bioethanol Production from Horticultural Waste Using Crude Fungal Enzyme Mixtures Produced by Solid State Fermentation

It was desired to study efficient and simplified methods to convert organosolv-pretreated horticultural waste (HW) to ethanol fuel using cellulase produced under solid-state fermentation (SSF). The unprocessed cellulase crude (72.2 %) showed better reducing sugar yield using filter paper than the commercial enzyme blend (68.7 %). Enzymatic hydrolysis of organosolv-pretreated HW using the crude cellulase with 20 % solid content, enzyme loading of 15 FPU/g HW at 50 °C, and pH 5.5 resulted in a HW hydrolysate containing 25.06 g/L glucose after 72 h. Fermentation of the hydrolysate medium produced 12.39 g/L ethanol with 0.49 g/g yield from glucose and 0.062 g/g yield from HW at 8 h using Saccharomyces cerevisiae. This study proved that crude cellulase complex produced under SSF and organosolv pretreatment can efficiently convert woody biomass to ethanol without any commercial cellulase usage.     

Fermentation of sugar cane bagasse hemicellulose hydrolysate to l(+)-lactic acid by a thermotolerant acidophilic Bacillus sp.**

Sugar cane bagasse hemicellulose, hydrolyzed by dilute H2SO4, supplemented with mineral salts and 0.5% corn steep liquor, was fermented to L(+)-lactic acid using a newly isolated strain of Bacillus sp. In batch fermentations at 50 degrees C and pH 5, over 5.5% (w/v) L(+)-lactic acid was produced (89% theoretical yield; 0.9 g lactate per g sugar) with an optical purity of 99.5%.     

Fractionation of Eucalyptus grandis chips by dilute acid-catalysed steam explosion

Steam explosion of Eucalyptus grandis has been carried out under various pretreatment conditions (200-210 degrees C, 2-5 min) after impregnation of the wood chips with 0.087 and 0.175% (w/w) H2SO4. This study, arranged as a 2(3) factorial design, indicated that pretreatment temperature is the most critical variable affecting the yield of steam-treated fractions. Pretreatment of 0.175% (w/w) H2SO4-impregnated chips at 210 degrees C for 2 min was the best condition for hemicellulose recovery (mostly as xylose) in the water soluble fraction, reaching almost 70% of the corresponding xylose theoretical yield. By contrast, lower pretreatment temperatures of 200 degrees C were enough to yield steam-treated substrates from which a 90% cellulose conversion was obtained in 48 h, using low enzyme loadings of a Celluclast 1.5 1 plus Novozym 188 mixture (Novo Nordisk). Release of water-soluble chromophores was monitored by UV spectroscopy and their concentration increased with pretreatment severity. The yield of alkali-soluble lignin increased at higher levels of acid impregnation and pretreatment temperatures. Thermoanalysis of these lignin fractions indicated a pattern of lignin fragmentation towards greater pretreatment severities but lignin condensation prevailed at the most drastic pretreatment conditions.     

Enhanced lignin peroxidase synthesis by Phanerochaete Chrysosporium in solid state bioprocessing of a lignocellulosic substrate

Summary A solid state fermentation (SSF) process for the production of lignin peroxidase was optimized to enhance enzyme production by Phanerochaete chrysosporium. Optimization of the corncob SSF medium caused a significant reduction in fermentation time to give maximum lignin peroxidase yield. Supplementation of the SSF medium by low concentrations of peptone, yeast extract and Tween-80 enhanced lignin peroxidase production. Maximum yield of lignin peroxidase was 13.7 U/gds (units per gram dry substrate) noted after 5 days of SSF with 70% moisture and 20% (v/w) inoculum.     

Effects of organosolv pretreatment and enzymatic hydrolysis on cellulose structure and crystallinity in Loblolly pine

Ethanol organosolv pretreatment was performed on Loblolly pine to enhance the efficiency of enzymatic hydrolysis of cellulose to glucose. Solid-state ¹³C NMR spectroscopy coupled with line shape analysis was used to determine the structure and crystallinity of cellulose isolated from pretreated and enzyme-hydrolyzed Loblolly pine. The results indicate reduced crystallinity of the cellulose following the organosolv pretreatment, which renders the substrate easily hydrolyzable by cellulase. The degree of crystallinity increases and the relative proportion of para-crystalline and amorphous cellulose decreases after enzymatic hydrolysis, indicating preferential hydrolysis of these regions by cellulase. The structural and compositional changes in this material resulting from the organosolv pretreatment and cellulase enzyme hydrolysis of the pretreated wood were studied with solid-state CP/MAS ¹³C NMR spectroscopy. NMR spectra of the solid material before and after the treatments show that hemicelluloses and lignin are degraded during the organosolv pretreatment.     

Bioethanol production from ammonia percolated wheat straw

This study examined the effectiveness of ammonia percolation pretreatment of wheat straw for ethanol production. Ground wheat straw at a 10% (w/v) loading was pretreated with a 15% (v/v) ammonia solution. The experiments were performed at treatment temperature of 50∼170°C and residence time of 10∼150 min. The solids treated with the ammonia solution showed high lignin degradation and sugar availability. The pretreated wheat straw was hydrolyzed by a cellulase complex (NS50013) and β-glucosidase (NS50010) at 45°C. After saccharification, Saccharomyces cerevisiae was added for fermentation. The incubator was rotated at 120 rpm at 35°C. As a result of the pretreatment, the delignification efficiency was > 70% (170°C, 30 min) and temperature was found to be a significant factor in the removal of lignin than the reaction time. In addition, the saccharification results showed an enzymatic digestibility of > 90% when 40 FPU/g cellulose was used. The ethanol concentration reached 24.15 g/L in 24 h. This paper reports a total process for bioethanol production from agricultural biomass and an efficient pretreatment of lignocellulosic material.     

Bioethanol production from barley hull using SAA (soaking in aqueous ammonia) pretreatment

Barley hull, a lignocellulosic biomass, was pretreated using aqueous ammonia, to be converted into ethanol. Barley hull was soaked in 15 and 30 wt.% aqueous ammonia at 30, 60, and 75 °C for between 12 h and 11 weeks. This pretreatment method has been known as “soaking in aqueous ammonia” (SAA). Among the tested conditions, the best pretreatment conditions observed were 75 °C, 48 h, 15 wt.% aqueous ammonia and 1:12 of solid:liquid ratio resulting in saccharification yields of 83% for glucan and 63% for xylan with 15 FPU/g-glucan enzyme loading. Pretreatment using 15 wt.% ammonia for 24–72 h at 75 °C removed 50–66% of the original lignin from the solids while it retained 65–76% of the xylan without any glucan loss.

Addition of xylanase along with cellulase resulted in synergetic effect on ethanol production in SSCF (simultaneous saccharification and co-fermentation) using SAA-treated barley hull and recombinant E. coli (KO11). With 3% w/v glucan loading and 4 mL of xylanase enzyme loadings, the SSCF of the SAA treated barley hull resulted 24.1 g/L ethanol concentration at 15 FPU cellulase/g-glucan loading, which corresponds to 89.4% of the maximum theoretical yield based on glucan and xylan.

SEM results indicated that SAA treatment increased surface area and the pore size. It is postulated that these physical changes enhance the enzymatic digestibility in the SAA treated barley hull.     

Optimization of alkaline pretreatment of coffee pulp for production of bioethanol

The use of lignocellulosic raw materials in bioethanol production has been intensively investigated in recent years. However, for efficient conversion to ethanol, many pretreatment steps are required prior to hydrolysis and fermentation. Coffee stands out as the most important agricultural product in Brazil and wastes such as pulp and coffee husk are generated during the wet and dry processing to obtain green grains, respectively. This work focused on the optimization of alkaline pretreatment of coffee pulp with the aim of making its use in the alcoholic fermentation. A central composite rotatable design was used with three independent variables: sodium hydroxide and calcium hydroxide concentrations and alkaline pretreatment time, totaling 17 experiments. After alkaline pretreatment the concentration of cellulose, hemicellulose, and lignin remaining in the material, the subsequent hydrolysis of the cellulose component and its fermentation of substrate were evaluated. The results indicated that pretreatment using 4% (w/v) sodium hydroxide solution, with no calcium hydroxide, and 25 min treatment time gave the best results (69.18% cellulose remaining, 44.15% hemicelluloses remaining, 25.19% lignin remaining, 38.13 g/L of reducing sugars, and 27.02 g/L of glucose) and produced 13.66 g/L of ethanol with a yield of 0.4 g ethanol/g glucose. © 2013 American Institute of Chemical Engineers Biotechnol. Prog., 30:451–462, 2014