Burn‐in Free Nonfullerene‐Based Organic Solar Cells

Organic solar cells that are free of burn‐in, the commonly observed rapid performance loss under light, are presented. The solar cells are based on poly(3‐hexylthiophene) (P3HT) with varying molecular weights and a nonfullerene acceptor (rhodanine‐benzothiadiazole‐coupled indacenodithiophene, IDTBR) and are fabricated in air. P3HT:IDTBR solar cells light‐soaked over the course of 2000 h lose about 5% of power conversion efficiency (PCE), in stark contrast to [6,6]‐Phenyl C61 butyric acid methyl ester (PCBM)‐based solar cells whose PCE shows a burn‐in that extends over several hundreds of hours and levels off at a loss of ≈34%. Replacing PCBM with IDTBR prevents short‐circuit current losses due to fullerene dimerization and inhibits disorder‐induced open‐circuit voltage losses, indicating a very robust device operation that is insensitive to defect states. Small losses in fill factor over time are proposed to originate from polymer or interface defects. Finally, the combination of enhanced efficiency and stability in P3HT:IDTBR increases the lifetime energy yield by more than a factor of 10 when compared with the same type of devices using a fullerene‐based acceptor instead.     

Organic Sensitizers with Bridged Triphenylamine Donor Units for Efficient Dye‐Sensitized Solar Cells

Bridged triphenylamine was chosen as the donor unit for metal‐free organic sensitizers in dye‐sensitized solar cells (DSSCs). The easily constructed alkene linkage between the donor and the spacer improves the molecule's delocalization and causes a large red shift in its absorption peaks. Planarization of the donor and the use of alkene linkage have proven powerful in extending the red light response of the sensitizer, leading to a significant enhancement in photocurrent density of the device. As a result, devices sensitized with target sensitizers LC‐2 (η = 7.51%) and LC‐3 (η = 8.00%) exhibited more than 70% efficiency increase over devices sensitized with the reference sensitizer LC‐1 (η = 4.44%).     

Nanofiber‐Based Bulk‐Heterojunction Organic Solar Cells Using Coaxial Electrospinning

Nanofibers consisting of the bulk heterojunction organic photovoltaic (BHJ–OPV) electron donor–electron acceptor pair poly(3‐hexylthiophene):phenyl‐C₆₁‐butyric acid methyl ester (P3HT:PCBM) are produced through a coaxial electrospinning process. While P3HT:PCBM blends are not directly electrospinnable, P3HT:PCBM‐containing fibers are produced in a coaxial fashion by utilizing polycaprolactone (PCL) as an electrospinnable sheath material. Pure P3HT:PCBM fibers are easily obtained after electrospinning by selectively removing the PCL sheath with cyclopentanone (average diameter 120 ± 30 nm). These fibers are then incorporated into the active layer of a BHJ–OPV device, which results in improved short‐circuit current densities, fill factors, and power‐conversion efficiencies (PCE) as compared to thin‐film devices of identical chemical composition. The best‐performing fiber‐based devices exhibit a PCE of 4.0%, while the best thin‐film devices have a PCE of 3.2%. This increase in device performance is attributed to the increased in‐plane alignment of P3HT polymer chains on the nanoscale, caused by the electrospun fibers, which leads to increased optical absorption and subsequent exciton generation. This methodology for improving device performance of BHJ–OPVs could also be implemented for other electron donor–electron acceptor systems, as nanofiber formation is largely independent of the PV material.     

High‐Efficiency CsPbI2Br Perovskite Solar Cells with Dopant‐Free Poly(3‐hexylthiophene) Hole Transporting Layers

CsPbI₂Br is emerging as a promising all‐inorganic material for perovskite solar cells (PSCs) due to its more stable lattice structure and moisture resistance compared to CsPbI₃, although its device performance is still much behind this counterpart. Herein, a preannealing process is developed and systematically investigated to achieve high‐quality CsPbI₂Br films by regulating the nucleation and crystallization of perovskite. The preannealing temperature and time are specifically optimized for a dopant‐free poly(3‐hexylthiophene) (P3HT)‐based device to target dopant‐induced drastic performance degradation for spiro‐OMeTAD‐based devices. The resulting P3HT‐based device exhibits comparable power conversion efficiency (PCE) to spiro‐OMeTAD‐based devices but much enhanced ambient stability with over 95% PCE after 1300 h. A diphenylamine derivative is introduced as a buffer layer to improve the energy‐level mismatch between CsPbI₂Br and P3HT. A record‐high PCE of 15.50% for dopant‐free P3HT‐based CsPbI₂Br PSCs is achieved by alleviating the open‐circuit voltage loss with the buffer layer. These results demonstrate that the preannealing processing together with a suitable buffer layer are applicable strategies for developing dopant‐free P3HT PSCs with high efficiency and stability.     

Lateral Organic Solar Cells with Self‐Assembled Semiconductor Nanowires

Solution‐processable organic semiconductor nanowires (NWs) offer a potentially powerful strategy for producing large‐area printed flexible devices. Here, the fabrication of lateral organic solar cells (LOSC) using solution‐processed organic NW blends on a flexible substrate to produce a power source for use in flexible integrated microelectronics is reported. A high photocarrier generation and an efficient charge sweep out are achieved by incorporating 1D self‐assembled poly(3‐hexylthiophene) NWs into the active layer, and an MoO₃ interfacial layer with high work function is introduced to increase the built‐in potential. These structures significantly increase the carrier diffusion/drift length and overall generated photocurrent in the channel. The utility of the LOSCs for high power source applications is demonstrated by using interdigitated electrode patterns that consist of multiple devices connected in parallel or in series. High photovoltage‐producing LOSC modules on plastic substrates for use in flexible optoelectronic devices are successfully fabricated. The LOSCs described here offer a new device architecture for use in highly flexible photoresponsive energy devices.     

Light Trapping with Dielectric Scatterers in Single‐ and Tandem‐Junction Organic Solar Cells

Efficient dielectric scatterers based on a mixture of TiO₂ nanoparticles and polydimethylsiloxane are demonstrated for light trapping in semitransparent organic solar cells. An improvement of 80% in the photocurrent of an optimized semitransparent solar cell is achieved with the dielectric scatterer with ≈100% diffuse reflectance for wavelengths larger than 400 nm. For a parallel tandem solar cell, the dielectric scatterer generates 20% more photocurrent compared with a silver mirror beneath the cell; for a series tandem solar cell, the dielectric scatterer can be used as a photocurrent balancer between the subcells with different photoabsorbing materials. The power conversion efficiency of the tandem cell in series configuration with balanced photocurrent in the subcells exceeds that of an optimized standard solar cell with a reflective electrode. The characteristics of polydimethylsiloxane, such as flexibility and the ability to stick conformably to surfaces, also remain in the dielectric scatterers, which makes the demonstrated light trapping configuration highly suitable for large scale module manufacturing of roll‐to‐roll printed organic single‐ or tandem‐junction solar cells.     

Development of Next‐Generation Organic‐Based Solar Cells: Studies on Dye‐Sensitized and Perovskite Solar Cells

Next‐generation organic solar cells such as dye‐sensitized solar cells (DSSCs) and perovskite solar cells (PSCs) are studied at the National Institute of Advanced Industrial Science and Technology (AIST), and their materials, electronic properties, and fabrication processes are investigated. To enhance the performance of DSSCs, the basic structure of an electron donor, π‐electron linker, and electron acceptor, i.e., D–π–A, is suggested. In addition, special organic dyes containing coumarin, carbazole, and triphenylamine electron donor groups are synthesized to find an effective dye structure that avoids charge recombination at electrode surfaces. Meanwhile, PSCs are manufactured using both a coating method and a laser deposition technique. The results of interfacial studies demonstrate that the level of the conduction band edge (CBE) of a compact TiO₂ layer is shifted after TiCl₄ treatment, which strongly affects the solar cell performance. Furthermore, a special laser deposition system is developed for the fabrication of the perovskite layers of PSCs, which facilitates the control over the deposition rate of methyl ammonium iodide used as their precursor.     

Comprehensive Insight into the Structure Contribution of A2-A1-D-A1-A2 Acceptor to Performance of P3HT Solar Cells

Poly(3-hexylthiophene) (P3HT) acting as one of the most popular and low-cost polymers is quite suitable for commercialization of organic solar cells but suffers from low power conversion efficiency (PCE) because of the limited matching non-fullerene acceptors (NFAs). One important reason that restricts the enhancement but remains unresolved is the undisclosed contributions of the subtle structure modification to the obvious performance change. In combination with the previous reports and this work, herein A₂-A₁-D-A₁-A₂ type NFAs with single, dual, and triple modifications based on parent BTA3 is designed, including benzyl-substitution on A₂ group (namely Bn modification), fluorine-substitution on A₁ group (namely F modification), and thieno[3,2-b]thiophene-substitution on D group (namely TT modification). It is finally found that the binary devices of P3HT with these NFAs underwent unexpected variations in the aspect of molecular optoelectronic property, blend morphological feature and charge generation process. The triple modification (including Bn, F, and TT) gives full play to their unique advantages and consequently increases PCE by 60%. To the knowledge, the obtained optimal PCE is one of the highest values for A₂-A₁-D-A₁-A₂ type NFAs. This study provides clearer insights into the rational substitutions on the A₂-A₁-D-A₁-A₂ acceptors matched with P3HT for high-performance organic photovoltaics.     

Sequential Blade‐Coated Acceptor and Donor Enables Simultaneous Enhancement of Efficiency,Stability, and Mechanical Properties for Organic Solar Cells

As a predominant fabrication method of organic solar cells (OSCs), casting of a bulk heterojunction (BHJ) structure presents overwhelming advantages for achieving higher power conversion efficiency (PCE). However, long‐term stability and mechanical strength are significantly crucial to realize large‐area and flexible devices. Here, controlling blend film morphology is considered as an effective way toward co‐optimizing device performance, stability, and mechanical properties. A PCE of 12.27% for a P‐i‐N‐structured OSC processed by sequential blade casting (SBC) is reported. The device not only outperforms the as‐cast BHJ devices (11.01%), but also shows impressive stability and mechanical properties. The authors corroborate such enhancements with improved vertical phase separation and purer phases toward more efficient transport and collection of charges. Moreover, adaptation of SBC strategy here will result in thermodynamically favorable nanostructures toward more stable film morphology, and thus improving the stability and mechanical properties of the devices. Such co‐optimization of OSCs will pave ways toward realizing the highly efficient, large‐area, flexible devices for future endeavors.     

Extended Conjugation Length of Nonfullerene Acceptors with Improved Planarity via Noncovalent Interactions for High‐Performance Organic Solar Cells

Three low‐bandgap nonfullerene acceptors (NFAs) IDTO‐T‐4F, IDTO‐Se‐4F, and IDTO‐TT‐4F with extended conjugation length are designed and synthesized. Various π‐spacers, thiophene, selenophene, and thieno[3,2‐b]thiophene are incorporated to extend the conjugated length and enhance the backbone planarity via noncovalent O···S or O···Se interactions. These NFAs exhibit strong light absorption in the range of 600–900 nm with narrow bandgaps between 1.38 and 1.45 eV. By blending with a wide‐bandgap donor material PBDB‐T, organic solar cells (OSCs) based on these NFAs all yield high efficiency over 10% with low energy losses ranging from 0.52 to 0.59 eV. Importantly, as a result of relatively high lowest unoccupied molecular orbital level, large hole and electron mobility in blend film, and low charge carrier recombination loss, optimized devices based on IDTO‐T‐4F exhibit a large open‐circuit voltage of 0.864 V, a high short‐circuit current density of 20.12 mA cm^?2, and a notable fill factor of 72.7%, leading to an impressive efficiency of 12.62%, which represents the best performance for NFA OSCs using noncovalent interactions in acceptor molecule design. The results indicate that optimizing the conjugation length and backbone planarity via intramolecular noncovalent O···S or O···Se interactions is a useful strategy for NFA materials invention toward high‐performance solar cells.     

Three‐Dimensional Nanostructured Indium‐Tin‐Oxide Electrodes for Enhanced Performance of Bulk Heterojunction Organic Solar Cells

A three‐dimensional indium tin oxide (ITO) nanohelix (NH) array is presented as a multifunctional electrode for bulk heterojunction organic solar cells for simultaneously improving light absorption and charge transport from the active region to the anode. It is shown that the ITO NH array, which is easily fabricated using an oblique‐angle‐deposition technique, acts as an effective antireflection coating as well as a light‐scattering layer, resulting in much enhanced light harvesting. Furthermore, the larger interfacial area between the electrode and the active layer, together with the enhanced carrier mobility through highly conductive ITO NH facilitate transport and collection of charge carriers. The optical and electrical improvements enabled by the ITO NH electrode result in a 10% increase in short‐circuit current density and power‐conversion efficiency of the solar cells.     

Nonfullerene n‐Type Organic Semiconductors for Perovskite Solar Cells

Compared to inorganic semiconductors and/or fullerene derivatives, nonfullerene n‐type organic semiconductors present some advantages, such as low‐temperature processing, flexibility, and molecule structure diversity, and have been widely used in perovskite solar cells (PSCs). In this research news article, the recent advances in nonfullerene n‐type organic semiconductors which function as electron‐transporting, interface‐modifying, additive, and light‐harvesting materials in PSCs are summarized. The remaining challenges and promising future directions of nonfullerene‐based PSCs are also discussed.     

Donor‐Acceptor Interfacial Interactions Dominate Device Performance in Hybrid P3HT‐ZnO Nanowire‐Array Solar Cells

The adsorption of self‐assembled monolayers (SAMs) on metal oxide surfaces is a promising route to control electronic characteristics and surface wettability. Here, arylphosphonic acid derivatives are used to modulate the surface properties of vertically oriented ZnO nanowire arrays. Arylphosphonate‐functionalized ZnO nanowires are incorporated into hybrid organic‐inorganic solar cells in which infiltrated poly(3‐hexylthiophene) (P3HT) serves as the polymer donor. Strong correlations between device short‐circuit current density (J _sc) and power conversion efficiencies (PCEs) with ZnO surface functionalization species are observed and a weak correlation in the open‐circuit voltage (V _oc) is observed. Inverted solar cells fabricated with these treated interfaces exhibit PCEs as high as 2.1%, primarily due to improvements in J _sc. Analogous devices using untreated ZnO arrays having efficiencies of 1.6%. The enhancement in J _sc is attributed to surface passivation of ZnO by SAMs and enhanced wettability from P3HT, which improve charge transfer and reduce carrier recombination at the organic‐inorganic interface in the solar cells.