Dietzia sp.S-JS-1利用煎炸废油生产生物破乳剂及其性能研究

以前期研究中筛选得到的破乳剂产生菌Dietzia sp.S-JS-1为研究对象,采用煎炸废油为培养碳源,考察菌株的生物量和表面张力,研究处理方式、温度、乳状液pH对破乳剂在两种模型乳状液W/O型(water in oil)和O/W型(oilin water)中破乳性能的影响,并初步分析生物破乳剂成分。结果表明:菌株最大生物量为2.6 g/L,其产生的破乳剂能够将纯水表面张力从72.0 mN/m降低到32.5 mN/m。冻融对破乳剂效果的影响小于高温灭菌;破乳剂经冷冻干燥处理后的破乳效果明显好于烘干处理;破乳剂在35℃～75℃时具有较好的破乳效果,脱水率均在75%以上;破乳剂在W/O型乳状液中的效果随着pH变大而逐渐增加,pH=10时的脱水率高达99.8%,而在O/W型乳状液中,pH=7时的脱水率最高,为90%左右。薄层色谱结果表明S-JS-1利用煎炸油生产的生物破乳剂可能含有5种脂肽类物质。     

pH对破乳菌Alcaligenes sp. S-XJ-1破乳性能的影响

从受石油污染的土壤中筛选出一株破乳菌Alcaligenes sp. S-XJ-1,该菌在初始pH6.0-11.0均可生长,其最适初始pH为10.0。在初始pH10.0条件下培养,破乳菌产量最高可达4.8g/L,菌悬液投加量为1000mg/L时,24h破乳率在85%以上。同时,该培养条件下得到的生物破乳菌细胞表面疏水性最大,对碳氢化合物的吸附能力达72.7%,接触角达115°。采用稳定性分析仪分别对pH7.0和pH10.0条件下培养得到的菌体的破乳效果进行分析,结果发现与初始pH7.0相比,初始pH10.0培养得到的破乳菌可以加速分散相粒径的增大,最终使乳状液破乳速率大幅提高。     

生物破乳菌的筛选及发酵条件的优化

生物破乳剂的开发可以降低油田乳状液对石油工业和生态环境的负面影响并减少化学破乳剂的使用量。本研究建立了一套高效、便捷的破乳菌筛选方法, 并对破乳菌的特性进行研究。利用大庆油田受石油污染土壤作为菌种来源, 将Tween 60-water(0.072%, V/V)和Span 60-oil (0.028%, V/V)以6.5:3.5体积比配置出可以稳定200 h以上的O/W型乳状液, 用于破乳菌破乳效能的评价。经过分离纯化、血平板试验、排油试验和破乳试验最终筛选出2株24 h平均排油率在80%以上的优势破乳菌, 初步鉴定为芽孢杆菌属(Bascillus)。通过该破乳菌发酵条的件优化得到, 当温度为25°C, 摇床转数为160 r/min, pH值为9, 接菌量为20%时对该破乳菌生长速率最快, 积累发酵产物的量最多; 当温度为35°C, 摇床转数为120 r/min, pH值为9, 接菌量为2%时该破乳菌代谢产物的破乳活性最高。     

一株高效生物表面活性剂产生菌的筛选鉴定及其性能研究

从新疆克拉玛依油田受石油污染的土壤中筛选到一株高效生物表面活性荆产生菌,编号为XJ-T-1,经16S rDNA同源性分析和生理生化试验鉴定为产碱杆菌.该菌株具有很强的产表面活性剂能力,全培养液的排油图直径能达到13.0cm,表面张力可降至30.0mN/m.投加10%(V/V)培养7d的XJ-T-1全培养液可使原油乳状液150min脱水率达到90%以上.XJ-T-1对原油具有高效降解作用,投加量为2%～5%(V/V),pH为中性或碱性,降解时间为7d时,XJ-T-1对7500mg/L高浓度含油废水的降解率可达80%以上.     

Dietzia sp. S-JS-1利用废弃油脂生产生物破乳剂的研究

生物破乳剂是近期开发出来的用于油水分离的新型破乳剂。本研究利用从受石油污染的土壤中筛选得到、并采用16S rRNA鉴定为Dietzia sp.的一株破乳剂产生菌, 在以废弃油脂MWFO、SWFO为碳源培养下, 得到的生物破乳剂的粗重为4 g/L、3.5 g/L; 对于W/O、O/W模型乳状液的破乳效果均可超过以液体石蜡产生的破乳剂, 且以SWFO废弃油脂培养得到的生物破乳剂可以同时应用于两种模型乳状液的使用。对于碳源利用方面Dietzia sp.在利用两种废弃油脂脂肪酸的过程中, 都是优先利用C16和C18的脂肪酸, 但对于两种废弃油脂的利用率上存在一定差异。采用TLC和FTIR分析发现, 3种碳源培养得到的生物破乳剂均为脂肽类生物破乳剂, 其破乳剂的化学结构还有待进一步研究。     

生物破乳剂产生菌混合培养及其发酵条件的优化

【目的】对菌株L1和XH1的混合发酵条件进行优化,为混合菌发酵生物破乳剂的实际生产和应用提供理论依据。【方法】利用响应面实验(RSM)的中心组合旋转设计方法(CCRD)针对混合菌的发酵条件进行优化,通过对模型乳状液进行破乳实验,以排油率作为发酵液破乳效能的评价标准。【结果】经模型的分析与验证,确定最佳发酵条件为：种子液比例(L1:XH1)为3:2,葡萄糖投加时间为第4天,投加葡萄糖后再培养21 h,液体石蜡含量3.6% (体积比)。【结论】与破乳菌XH1和L1单独培养相比,经混合培养后获得复合生物破乳剂具有投加量少、破乳接触时间短的优势。同时双株破乳菌复配培养有效地提高了培养基中主要营养物质的利用率,减少了对底物的浪费。     

生物破乳剂产生菌的筛选及其方法研究

针对生物破乳剂产生菌筛选难的问题, 采用显色法、溶血细胞测试法、表面张力测定法和排油圈法从6种不同菌源对生物破乳菌产生菌进行了筛选。通过试验筛选得到了17株生物破乳剂产生菌, 其中24h内破乳率高于70%的破乳菌有5株; 油田含油污泥、采油废水生物处理污泥和污水处理厂剩余污泥是筛选破乳菌的较好的菌源; 显色法、溶血圈法存在检测范围的局限性; 表面张力测定法和排油圈法是最为简易和准确的生物表面活性剂产生菌的筛选方法, 采用模型乳状液对生物破乳剂产生菌进行筛选最为直接和准确, 但工作量大、所需时间长, 因此在筛选高效破乳菌时, 建议采用表面张力、排油圈法进行初筛, 而后通过模型乳状液破乳进行验证。     

生物破乳剂产生菌的筛选及其方法研究

针对生物破乳剂产生菌筛选难的问题,采用显色法、溶血细胞测试法、表面张力测定法和排油圈法从6种不同菌源对生物破乳菌产生茵进行了筛选.通过试验筛选得到了17株生物破乳剂产生茵,其中24h内破乳率高于70%的破乳菌有5株;油田含油污泥、采油废水生物处理污泥和污水处理厂剩余污泥是筛选破乳菌的较好的菌源:显色法、溶血圈法存在检测范围的局限性;表面张力测定法和排油圈法是最为简易和准确的生物表面活性剂产生茵的筛选方法,采用模型乳状液对生物破乳剂产生菌进行筛选最为直接和准确,但工作量大、所需时间长,因此在筛选高效破乳菌时,建议采用表面张力、排油圈法进行初筛,而后通过模型乳状液破乳进行验证.     

假单细菌GX_4-1利用鱼粉废水产絮凝剂的研究

研究了假单胞菌 (Pseudomonassp .)GX4 1利用鱼粉废水产生絮凝剂的条件 ,结果表明 ,适宜条件为废水COD浓度为 1 0g/L左右、初始pH为 7～ 9、培养温度为 30℃、摇床转速为 1 0 0～ 2 50r/min ,此时的絮凝率可高达 99 5%。同时发现在废水培养基不灭菌的条件下 ,该菌仍能产生高效的絮凝剂。该菌利用鱼粉废水产生的絮凝剂对高岭土悬液、土壤悬液和细活性炭粉末悬液和电瓷厂污水均有较好的絮凝作用。     

假单细菌GX4-1利用鱼粉废水产絮凝剂的研究

研究了假单胞菌 (Pseudomonassp .)GX4 1利用鱼粉废水产生絮凝剂的条件 ,结果表明 ,适宜条件为废水COD浓度为 1 0g/L左右、初始pH为 7～ 9、培养温度为 30℃、摇床转速为 1 0 0～ 2 50r/min ,此时的絮凝率可高达 99 5%。同时发现在废水培养基不灭菌的条件下 ,该菌仍能产生高效的絮凝剂。该菌利用鱼粉废水产生的絮凝剂对高岭土悬液、土壤悬液和细活性炭粉末悬液和电瓷厂污水均有较好的絮凝作用。     

Evaluation of screening methods for demulsifying bacteria and characterization of lipopeptide bio-demulsifier produced by Alcaligenes sp

In this paper, surface tension measurement, oil-spreading test and blood-plate hemolysis test were attempted in the screening of demulsifying bacteria. After the comparison to the screening results obtained in demulsification test, 50 mN/m of surface tension of culture was proposed as a preliminary screening standard for potential demulsifying bacteria. For the identification of efficient demulsifying strains, surface tension level was set at 40 mN/m. The detected strains were further verified in demulsification test. Compared to using demulsification test alone as screening method, the proposed screening protocol would be more efficient. From the screening, a highly efficient demulsifying stain, S-XJ-1, was isolated from petroleum-contaminated soil and identified as Alcaligenes sp. by 16S rRNA gene and physiological test. It achieved 96.5% and 49.8% of emulsion breaking ratio in W/O and O/W kerosene emulsion within 24h, respectively, and also showed 95% of water separation ratio in oilfield petroleum emulsion within 2h. The bio-demulsifier was found to be cell-wall combined. After soxhlet extraction and purification through silicon-gel column, the bio-demulsifier was then identified as lipopeptide biosurfactant by TLC and FT-IR.     

Water-in-oil emulsions that improve the storage and delivery of the biolarvacide <Emphasis Type="Italic">Lagenidium giganteum</Emphasis>

Lagenidium giganteum is an effective biological control agent for mosquitoes with limited use due to poor survival and contamination during storage. Invert (water-in-oil) emulsions using crop oils were investigated for formulating L. giganteum mycelium for improved shelf life and delivery. Cells formulated in a water-in-oil (W/O) emulsion were just as effective against larvae as those formulated in aqueous suspension. Cells formulated in the W/O emulsion and cell suspension settled during storage and formed clumps, which significantly reduced the efficacy of formulations. Hydrophobic silica nanoparticles were added to the W/O emulsion formulation for oil thickening. The addition of silica significantly reduced cell sedimentation and improved storage; thickened W/O emulsions with an initial cell density of 3900 CFU/mg applied at 0.5 mg/cm² were greater than 95% effective at infecting mosquitoes after 12 weeks of storage at room temperature. Cell density reduction during storage was represented using first-order kinetics. Surface treatment of silica nanoparticles and oil refinement both had a significant effect on the first-order rate constant; as the hydrophobicity of the silica increased and level of oil refinement decreased, the rate constant increased. The percentage of water in the W/O emulsion and type of refined crop oil had no significant effect on the first-order rate constant. Cells formulated in the thickened W/O emulsion were less likely to settle when applied to water compared to cells in aqueous suspension, suggesting better cell distribution in an aqueous environment could be achieved when cells are applied in a W/O emulsion.     

一株嗜热子囊菌产生的碱性耐热过氧化氢酶及其应用潜力

研究了一株嗜热子囊菌产过氧化氢酶的摇瓶发酵条件,并对其在纺织工业中的应用潜力进行了评价。以20 g/L糊精和1%(V/V)乙醇为混合碳源时,过氧化氢酶酶活达到1594 u/Ml,比以糊精和乙醇单独为碳源时过氧化氢酶的活力之和还高23%。改变培养基的初始Ph、提高发酵液中的溶氧水平及添加外源过氧化氢,过氧化氢酶的产量进一步提高到2762 u/Ml,比优化前提高了5.8倍。将嗜热子囊菌的过氧化氢酶同来源于牛肝、黑曲霉的过氧化氢酶进行了热(70℃, 80℃, 90℃)、碱(Ph 9.0, Ph 10.0, Ph 11.0)稳定性的比较。结果显示,产自嗜热子囊菌的过氧化氢酶对高温和强碱性的耐受性能明显优于其它来源的酶,在纺织染整工艺中具有良好的应用潜力。     

一株产脂肽类表面活性剂的碱性Dietzia菌及特性研究

【目的】筛选降解性能良好的产生物表面活性剂的菌株,对其进行分类学鉴定,确定所产表面活性剂物质并对各影响因素进行评价。【方法】利用液体石蜡为底物筛选降解性能良好的产生物表面活性剂菌株,通过形态特征观察、生理生化测定、16S rRNA基因序列分析等实验确定菌株的分类地位。通过排油圈活性、表面张力值、薄层层析等方法确定生物表面活性剂的性质,分析碳、氮源和温度、pH、盐浓度各因素对菌株产生物表面活性剂的影响。【结果】从大连新港采集的样品中分离得到一株产表面活性剂的嗜碱菌株3372,经分类鉴定表明其是Dietzia cercidiphylli的新菌株。嗜碱菌3372发酵液粗提物的排油直径为6.1 cm,表面张力可从67.62 mN/m降到32.95 mN/m,经薄层层析分析,初步鉴定为脂肽类表面活性剂。综合各因素对发酵液表面活性的影响,菌株3372在pH为9.0、适盐浓度为3%的培养基中,经30°C培养可将发酵液表面张力值降到最低。【结论】嗜碱菌3372是脂肽类生物表面活性剂产生菌的新成员,其在高盐碱条件下产生表面活性剂的特性在工业应用上有一定的潜力。     

The effect of alkaline earth cations and of ionic strength on the dissociation of earthworm hemoglobin at alkaline pH

1. The effect of alkaline earth cations on the dissociation of the extracellular hemoglobin of Lumbricus terrestris and the effect of ionic strength on the dissociation of the hemoglobins of L. terrestris and Tubifex tubifex at concentrations of ca 2.5 mg/ml, over the pH range 9.0-10.5 was investigated using ultracentrifugation to separate the dissociated from the undissociated molecules. 2. Mg(II), Ca(II) and Sr(II) at concentrations of up to 0.2 M, decreased the dissociation of Lumbricus oxyhemoglobin from 70% at pH 9.0 and 100% at pH 9.5 and higher, to 20-30% at 0.05 M. The three cations were equally effective in decreasing the extent of dissociation of L. terrestris oxyhemoglobin over the pH range 9.0-10.5, with a K1/2 of ca 10 mM. 3. The dissociation of L. terrestris oxyhemoglobin over the pH range 9.0-10.5 was decreased only to 50-60% in the presence of up to 0.5 M NaCl or KCl; there was no further decrease in dissociation at concentrations of the two salts up to 1.5 M. 4. The dissociation of T. tubifex oxyhemoglobin over the pH range 9.0-10.0 was decreased from 100% to ca 40-50% in the presence of 0.5 M NaCl or KCl with little or no change at higher concentrations. At pH 10.5 and 11.0 the decrease in dissociation was more gradual, reaching ca 50% at 1.5 M NaCl.     

Thermostable, alkalophilic and cellulase free xylanase production by Thermoactinomyces thalophilus subgroup C

Thermoactinomyces thalophilus produced cellulase free extracellular endo-1,4-beta-xylanase (EC 3.2.1.8) at 50 degrees C and pH 8.5. Maximum xylanase production was achieved in fermentation medium using birchwood xylan as substrate after 96 h of growth at 50 degrees C. Other agricultural substrates such as wheat bran, wheat straw, sugarcane bagasse and cornstover produced less xylanase. The crude enzyme preparation from mutant T. thalophilus P2 grown under optimised fermentation conditions showed no cellulase contamination and maximum xylanase activity of 42 U/ml at 65%deg;C and pH 8.5-9.0. This enzyme with initial xylanase activity of 42 U/ml was found thermostable up to 65 degrees C and retaining 50% of its activity after its incubation for 125 min at 65 degrees C.