Biosorption of acid violet dye from aqueous solutions using native biomass of a new isolate of Penicillium sp.

Laboratory investigation of the potential use of Penicillium sp. as biosorbent for the removal of acid violet dye from aqueous solution was studied with respect to pH, temperature, biosorbent, initial dye concentrations. Penicillium sp. decolourizes acid violet (30 mg l⁻¹) within 12 h agitation of 150 rpm at pH 5.7 and temperature of 35 °C. The pellets exhibited a high dye adsorption capacity (5.88 mg g⁻¹) for acid violet dye over a pH range (4–9); the maximum adsorption was obtained at pH 5.7. The increase of temperature favored biosorption for acid violet, but the optimum temperature was 35 °C. Adsorption kinetic data were tested using pseudo-first-order, pseudo-second-order and kinetic studies showed that the biosorption process follows pseudo-first-order rate kinetics with an average rate constant of 0.312 min⁻¹. Isotherm experiments were conducted to determine the sorbent–desorption behavior of examined dye from aqueous solutions using Langmuir and Freundlich equations. Langmuir parameter indicated a maximum adsorption capacity of 4.32 mg g⁻¹ for acid violet and R_L value of 0.377. Linear plot of log q_e vs log C_e shows that applicability of Freundlich adsorption isotherm model. These results suggest that this fungus can be used in biotreatment process as biosorbent for acid dyes.     

Taguchi DoE methodology for modeling of synthetic dye biosorption from aqueous effluents: parametric and phenomenological studies

Abstract

Biosorption technology has been acknowledged as one of the most successful treatment approaches for colored industrial effluents. The problems such as its high manufacturing cost and poor regeneration capability in the use of activated carbon as a biosorbent have prompted the environmental scientists to develop alternative biosorbent materials. In this context, as a sustainable green generation alternative biosorbent source, the discarded seed biomass from pepper (Capsicum annuum L.) processing industry was explored for the biotreatment of colored aqueous effluents in this study. To test the wastewater cleaning ability of biosorbent, Basic red 46 was selected as a typical model synthetic dye. Taguchi DoE methodology was employed to study the effect of important operational parameters, contact time, pH and synthetic dye concentration, on the biosorption process and to develop a mathematical model for the estimation of biosorption potential of biosorbent. The percentage contribution of each of these process variables on the dye biosorption was found to be 19.31%, 41.39%, and 38.74%, respectively. The biosorption capacity under the optimum environmental conditions, contact time of 360?min, pH of 8 and dye concentration of 30?mg L^?1, was estimated to be 92.878?mg g^?1 (R²: 99.45). This value was very close to the experimentally obtained dye removal performance value (92.095?mg g^?1). These findings indicated the high ability of Taguchi DoE technique in the optimization and simulation of dye biosorption system. The kinetic and equilibrium modeling studies showed that the pseudo-second-order and Langmuir models were the best models for the elucidation of dye removal behavior of biosorbent. The thermodynamic studies displayed that the dye biosorption was a feasible, spontaneous and exothermic process. This parametric and phenomenological survey revealed that the discarded pepper seed biomass can be introduced as a potential and efficient biosorbent for the bioremediation of colored industrial effluents.     

Biosorption of Acid Black 172 and Congo Red from aqueous solution by nonviable Penicillium YW 01: Kinetic study, equilibrium isotherm and artificial neural network modeling

The main objective of this work was to investigate the biosorption performance of nonviable Penicillium YW 01 biomass for removal of Acid Black 172 metal-complex dye (AB) and Congo Red (CR) in solutions. Maximum biosorption capacities of 225.38 and 411.53 mg g⁻¹ under initial dye concentration of 800 mg L⁻¹, pH 3.0 and 40 °C conditions were observed for AB and CR, respectively. Biosorption data were successfully described with Langmuir isotherm and the pseudo-second-order kinetic model. The Weber-Morris model analysis indicated that intraparticle diffusion was the limiting step for biosorption of AB and CR onto biosorbent. Analysis based on the artificial neural network and genetic algorithms hybrid model indicated that initial dye concentration and temperature appeared to be the most influential parameters for biosorption process of AB and CR onto biosorbent, respectively. Characterization of the biosorbent and possible dye-biosorbent interaction were confirmed by Fourier transform infrared spectroscopy and scanning electron microscopy.     

Preparation,Characterization and Application of Magnetic Fe3O4-CS for the Adsorption of Orange I from Aqueous Solutions

Fe₃O₄ (Fe₃O₄-CS) coated with magnetic chitosan was prepared as an adsorbent for the removal of Orange I from aqueous solutions and characterized by FTIR, XRD, SEM, TEM and TGA measurements. The effects of pH, initial concentration and contact time on the adsorption of Orange I from aqueous solutions were investigated. The decoloration rate was higher than 94% in the initial concentration range of 50–150 mg L⁻¹ at pH 2.0. The maximum adsorption amount was 183.2 mg g⁻¹ and was obtained at an initial concentration of 400 mg L⁻¹ at pH 2.0. The adsorption equilibrium was reached in 30 minutes, demonstrating that the obtained adsorbent has the potential for practical application. The equilibrium adsorption isotherm was analyzed by the Freundlich and Langmuir models, and the adsorption kinetics were analyzed by the pseudo-first-order and pseudo-second-order kinetic models. The higher linear correlation coefficients showed that the Langmuir model (R² = 0.9995) and pseudo-second-order model (R² = 0.9561) offered the better fits.     

Biosorption of Cr(VI) by Ceratocystis paradoxa MSR2 Using Isotherm Modelling,Kinetic Study and Optimization of Batch Parameters Using Response Surface Methodology

This study is focused on the possible use of Ceratocystis paradoxa MSR2 native biomass for Cr(VI) biosorption. The influence of experimental parameters such as initial pH, temperature, biomass dosage, initial Cr(VI) concentration and contact time were optimized using batch systems as well as response surface methodology (RSM). Maximum Cr(VI) removal of 68.72% was achieved, at an optimal condition of biomass dosage 2g L⁻¹, initial Cr(VI) concentration of 62.5 mg L⁻¹ and contact time of 60 min. The closeness of the experimental and the predicted values exhibit the success of RSM. The biosorption mechanism of MSR2 biosorbent was well described by Langmuir isotherm and a pseudo second order kinetic model, with a high regression coefficient. The thermodynamic study also revealed the spontaneity and exothermic nature of the process. The surface characterization using FT-IR analysis revealed the involvement of amine, carbonyl and carboxyl groups in the biosorption process. Additionally, desorption efficiency of 92% was found with 0.1 M HNO₃. The Cr(VI) removal efficiency, increased with increase in metal ion concentration, biomass concentration, temperature but with a decrease in pH. The size of the MSR2 biosorbent material was found to be 80 μm using particle size analyzer. Atomic force microscopy (AFM) visualizes the distribution of Cr(VI) on the biosorbent binding sites with alterations in the MSR2 surface structure. The SEM-EDAX analysis was also used to evaluate the binding characteristics of MSR2 strain with Cr(VI) metals. The mechanism of Cr(VI) removal of MSR2 biomass has also been proposed.     

DETERMINATION OF METHYLENE BLUE BIOSORPTION BY Rhizopus arrhizus IN THE PRESENCE OF SURFACTANTS WITH DIFFERENT CHEMICAL STRUCTURES

Methylene blue (MB) biosorption properties of Rhizopus arrhizus were investigated in the presence of surfactants. The effects of cationic and anionic surfactants on MB removal by dead biomass (1 g L^?1) were determined. MB removal was tested as a function of initial pH (2–12), contact time (5–1440 min), and dye (37.4–944.7 mg L^?1) and surfactant (0–10 mM) concentrations. The opposite charged anionic surfactant dodecylbenzenesulfonic acid sodium salt (DBS) enhanced sorption of cationic MB by biomass dramatically. Maximum biosorption capacity was 471.5 mg g^?1 at pH 8 with 0.5 mM DBS at 944.7 mg L^?1 MB concentration. The surfactant-stimulated fungal decolorization method may provide a highly efficient, inexpensive, and time-saving procedure in biological wastewater treatment technologies.     

Senna auriculata L. flower petal biomass: An alternative green biosorbent for the removal of fluoride from aqueous solutions

Fluoride contamination in groundwater is a major concern in many parts of India and all over the world. Researches paying attention for the removal of fluoride through the application of biosorbents prepared from different parts of plants are finding greater scope and importance. The present research work focuses on Senna auriculata L., flower petal biomass as biosorbent, and evaluated its feasibility for fluoride ion elimination from aqueous solutions. Batch experiments were conducted to remove fluoride under different experimental conditions have been optimized for the maximum removal of fluoride; 80% removal was observed at pH: 6, sorbent dosage: 0.25 g/100 mL, time of agitation: 90 min, and initial concentration of the fluoride ions: 5 mg/L. Characterization studies of the biosorbent revealed its favorability towards the sorption of fluoride. In the isothermal modeling studies, Langmuir isotherm model was obeyed by the biosorption process with R² value of 0.98 and from a kinetic perspective, the biosorption of fluoride onto the biosorbent observed the pseudo-second-order reaction with R² value of 0.98. The developed biosorbent has been applied to real field fluoride-contaminated water samples and found to be successful.     

Use of Spirulina platensis micro and nanoparticles for the removal synthetic dyes from aqueous solutions by biosorption

In this research, micro and nanoparticles of Spirulina platensis dead biomass were obtained, characterized and employed to removal FD&C red no. 40 and acid blue 9 synthetic dyes from aqueous solutions. The effects of particle size (micro and nano) and biosorbent dosage (from 50 to 750 mg) were studied. Pseudo-first order, pseudo-second order and Elovich models were used to evaluate the biosorption kinetics. The biosorption nature was verified using energy dispersive X-ray spectroscopy (EDS). The best results for both dyes were found using 250 mg of nanoparticles, in these conditions, the biosorption capacities were 295 mg g^?1 and 1450 mg g^?1, and the percentages of dye removal were 15.0 and 72.5% for the FD&C red no. 40 and acid blue 9, respectively. Pseudo-first order model was the more adequate to represent the biosorption of both dyes onto microparticles, and Elovich model was more appropriate to the biosorption onto nanoparticles. The EDS results suggested that the dyes biosorption onto microparticles occurred mainly by physical interactions, and for the nanoparticles, chemisorption was dominant.     

Sunscreen Products as Emerging Pollutants to Coastal Waters

A growing awareness of the risks associated with skin exposure to ultraviolet (UV) radiation over the past decades has led to increased use of sunscreen cosmetic products leading the introduction of new chemical compounds in the marine environment. Although coastal tourism and recreation are the largest and most rapidly growing activities in the world, the evaluation of sunscreen as source of chemicals to the coastal marine system has not been addressed. Concentrations of chemical UV filters included in the formulation of sunscreens, such as benzophehone 3 (BZ-3), 4-methylbenzylidene camphor (4-MBC), TiO₂ and ZnO, are detected in nearshore waters with variable concentrations along the day and mainly concentrated in the surface microlayer (i.e. 53.6–577.5 ng L^-1 BZ-3; 51.4–113.4 ng L^-1 4-MBC; 6.9–37.6 µg L^-1 Ti; 1.0–3.3 µg L^-1 Zn). The presence of these compounds in seawater suggests relevant effects on phytoplankton. Indeed, we provide evidences of the negative effect of sunblocks on the growth of the commonly found marine diatom Chaetoceros gracilis (mean EC₅₀ = 125±71 mg L^-1). Dissolution of sunscreens in seawater also releases inorganic nutrients (N, P and Si forms) that can fuel algal growth. In particular, PO₄ ³⁻ is released by these products in notable amounts (up to 17 µmol PO₄ ³⁻ g⁻¹). We conservatively estimate an increase of up to 100% background PO₄ ³⁻ concentrations (0.12 µmol L^-1 over a background level of 0.06 µmol L^-1) in nearshore waters during low water renewal conditions in a populated beach in Majorca island. Our results show that sunscreen products are a significant source of organic and inorganic chemicals that reach the sea with potential ecological consequences on the coastal marine ecosystem.     

Intracellular Biosynthesis and Removal of Copper Nanoparticles by Dead Biomass of Yeast Isolated from the Wastewater of a Mine in the Brazilian Amazonia

In this study was developed a natural process using a biological system for the biosynthesis of nanoparticles (NPs) and possible removal of copper from wastewater by dead biomass of the yeast Rhodotorula mucilaginosa. Dead and live biomass of Rhodotorula mucilaginosa was used to analyze the equilibrium and kinetics of copper biosorption by the yeast in function of the initial metal concentration, contact time, pH, temperature, agitation and inoculum volume. Dead biomass exhibited the highest biosorption capacity of copper, 26.2 mg g⁻¹, which was achieved within 60 min of contact, at pH 5.0, temperature of 30°C, and agitation speed of 150 rpm. The equilibrium data were best described by the Langmuir isotherm and Kinetic analysis indicated a pseudo-second-order model. The average size, morphology and location of NPs biosynthesized by the yeast were determined by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS) and transmission electron microscopy (TEM). The shape of the intracellularly synthesized NPs was mainly spherical, with an average size of 10.5 nm. The X-ray photoelectron spectroscopy (XPS) analysis of the copper NPs confirmed the formation of metallic copper. The dead biomass of Rhodotorula mucilaginosa may be considered an efficiently bioprocess, being fast and low-cost to production of copper nanoparticles and also a probably nano-adsorbent of this metal ion in wastewater in bioremediation process.     

Biosorption characteristics of Aspergillus fumigatus for the decolorization of triphenylmethane dye acid violet 49

This study focuses on the possible use of Aspergillus fumigatus to remove acid violet 49 dye (AV49) from aqueous solution. In batch biosorption experiments, the highest biosorption efficiency was achieved at pH 3.0, with biosorbent dosage of 3.0 gL^?1 within about 30 min at 40 °C. The Langmuir and Freundlich models were able to describe the biosorption equilibrium of AV49 onto fungal biomass with maximum dye uptake capacity 136.98 mg g^?1. Biosorption followed a pseudo-second-order kinetic model with high correlation coefficients (R ²?>?0.99), and the biosorption rate constants increased with increasing temperature. Thermodynamic parameters indicated that the biosorption process was favorable, spontaneous, and endothermic in nature, with insignificant entropy changes. Fourier transform infrared spectroscopy strongly supported the presence of several functional groups responsible for dye–biosorbent interaction. Fungal biomass was regenerated with 0.1 M sodium hydroxide and could be reused a number of times without significant loss of biosorption activity. The effective decolorization of AV49 in simulated conditions indicated the potential use of biomass for the removal of color contaminants from wastewater.     

Bioremediation potential of a widespread industrial biowaste as renewable and sustainable biosorbent for synthetic dye pollution

In this study, a model synthetic azo dye (Basic red 46) bioremoval by Carpinus betulus sawdust as inexpensive, eco-friendly, and sustainable biosorbent from aqueous solution was examined in a batch biosorption system. The effective environmental parameters on the biosorption process, such as the value of pH, amount of biosorbent, initial dye concentration and contact time were optimized using classical test design. The possible dye-biosorbent interaction was determined by Fourier Transform Infrared Spectroscopy (FTIR) and Scanning Electron Microscopy (SEM). The equilibrium, thermodynamic, and kinetic studies for the biosorption of Basic red 46 onto the sawdust biomass were performed. In addition, a single-stage batch dye biosorption system was also designed. The dye biosorption yield of biosorbent was significantly influenced by the change of operating variables. The experimental data were best described by the Freundlich isotherm model and both the pseudo-first-order kinetic and the pseudo-second-order kinetic models. Thermodynamic research indicated that the biosorption of dye was feasible and spontaneous. Based on the Langmuir isotherm model, the biosorbent was found to have a maximum biosorption potential higher than many other biosorbents in the literature (264.915?mg g^?1). Thus, this investigation presents a novel green option for the assessment of waste sawdust biomass as a cheap and effective biosorbent material.     

Influence of wastewater composition on nutrient removal behaviors in the new anaerobic–anoxic/nitrifying/induced crystallization process

In this study, the new anaerobic–anoxic/nitrifying/induced crystallization (A₂N–IC) system was compared with anaerobic-anoxic/nitrifying (A₂N) process to investigate nutrient removal performance under different influent COD and ammonia concentrations. Ammonia and COD removal rates were very stable in both processes, which were maintained at 84.9% and 86.6% when the influent ammonia varied from 30 mg L⁻¹ to 45 mg L⁻¹ and COD ranged from 250 mg L⁻¹ to 300 mg L⁻¹. The effluent phosphorus always maintained below 0.2 mg L⁻¹ in A₂N–IC, whereas in A₂N the effluent phosphorus concentration was 0.4–1.7 mg L⁻¹, demonstrating that A₂N–IC is suitable to apply in a broader influent COD and ammonia concentration range. Under higher influent COD (300 mg L⁻¹) or lower ammonia conditions (30 mg L⁻¹), the main function of chemical induced crystallization was to coordinate better nutrient ratio for anoxic phosphorus uptake, whereas under high phosphorus concentration, it was to reduce phosphorus loading for biological system. Under the similar influent wastewater compositions, phosphorus release amounts were always lower in A₂N–IC. To clarify the decrease procedure of phosphorus release in the A₂N–IC, the equilibrium between chemical phosphorus removal and biological phosphorus removal in A₂N–IC was analyzed by mass balance equations. During the long-term experiment, some undesirable phenomena were observed: the declining nitrification in post-aerobic tank and calcium phosphorus precipitation in the anaerobic tank. The reasons were analyzed; furthermore, the corresponding improvements were proposed. Nitrification effect could be enhanced in the post-aerobic tank, therefore ammonia removal rate could be increased; and biologically induced phosphorus precipitation could be inhibited by controlling pH at the anaerobic stage, so the phosphorus release and recovery could be improved.     

The Behavior of Organic Phosphorus under Non-Point Source Wastewater in the Presence of Phototrophic Periphyton

To understand the role of ubiquitous phototrophic periphyton in aquatic ecosystem on the biogeochemical cycling of organic phosphorus, the conversion and removal kinetic characteristics of organic phosphorus (Porg) such as adenosine triphosphate (ATP) were investigated in the presence of the periphyton cultured in artificial non-point source wastewater. The preliminary results showed that the periphyton was very powerful in converting P_org evidenced by the fact that inorganic phosphorus (P_inorg) content in solution increased from about 0.7 to 14.3 mg P L⁻¹ in 48 hours in the presence of 0.6 g L⁻¹ periphyton. This was because the periphyton could produce abundant phosphatases that benefited the conversion of P_org to P_inrog. Moreover, this conversion process was described more suitable by the pseudo-first-order kinetic model. The periphyton was also effective in removing P_org, which showed that the P_org can be completely removed even when the initial P_org concentration was as high as 13 mg P L⁻¹ in 48 hours in the presence of 1.6 g L⁻¹ periphyton. Furthermore, it was found that biosorption dominated the P_org removal process and exhibited the characteristics of physical adsorption. However, this biosorption process by the periphyton was significantly influenced by biomass (absorbent dosage) and temperature. This work provides insights into P_org biogeochemical circulation of aquatic ecosystem that contained the periphyton or similar microbial aggregates.     

Application of a novel phyco-composite biosorbent for the biotreatment of aqueous medium polluted with manganese ions

A composite phyco-biomass including four different marine macroalgae species (Chaetomorpha sp., Polysiphonia sp., Ulva sp., and Cystoseira sp.) was evaluated as a novel biosorbent for the biosorption of manganese ions from aqueous solution. The experimental studies were performed to optimize the operational factors including solution pH, biosorbent amount, initial manganese concentration, and reaction time in a batch-mode biosorption system. The removal yield of the biosorbent for manganese ions increased with increasing pH, manganese ion concentration, and reaction time, while it decreased as the biosorbent dose increased. The obtained kinetic data indicated that the removal of manganese ions by the biosorbent was best described by the pseudo-second-order model and the pore diffusion also contributed to the biosorption process. The results of isotherm and thermodynamic studies showed that the Freundlich model represented the biosorption equilibrium data well and this biotreatment system was feasible, spontaneous, and physical. The maximum manganese uptake capacity of used biosorbent was found to be 55.874 mg g^?1. Finally, a single-stage batch manganese biosorption system was designed and its kinetic performance was evaluated. All these findings revealed that the prepared composite macroalgae biosorbent has a fairly good potential for the removal of manganese ions from the aqueous medium.     

Biosorption of di(2-ethylhexyl)phthalate by seaweed biomass

Samples of various Sargassum species were collected in the Hong Kong marine environment and used for studies on biosorption of di(2-ethylhexyl)phthalate (DEHP). Batch adsorption experiments were carried out to determine the removal capacity and removal efficiency of the biosorbents. The DEHP removal ability was similar among beached seaweed and three freshly collected Sargassum species. Different physico-chemical factors were evaluated in order to enhance the performance of the biosorbents. Under optimized conditions (25 mg biomass, initial pH 4, 25 °C, 40 mg L^–1 DEHP), the mean removal capacity of beached seaweed and Sargassum siliquastrum was 5.68 and 6.54 mg g^–1, respectively. Examination of the Langmuir and Freundlich adsorption isotherms showed that the biosorption phenomenon by these biosorbents could well be described by these models. Desorption of DEHP was also assessed with methanol, which showed the most satisfactory desorbing ability. Further study in multiple adsorption–desorption of DEHP by the biosorbents demonstrated the reusability of both beached seaweed and S. siliquastrum for biosorption of DEHP.     

Removal of Acid Blue25 from aqueous solutions using Bengal gram fruit shell (BGFS) biomass

The feasibility for the removal of Acid Blue25 (AB25) by Bengal gram fruit shell (BGFS), an agricultural by-product, has been investigated as an alternative for high-cost adsorbents. The impact of various experimental parameters such as dose, different dye concentration, solution pH, and temperature on the removal of Acid Blue25 (AB25) has been studied under the batch mode of operation. pH is a significant impact on the sorption of AB25 onto BGFS. The maximum removal of AB25 was achieved at a pH of 2 (83.84%). The optimum dose of biosorbent was selected as 200 mg for the removal of AB25 onto BGFS. Kinetic studies reveal that equilibrium reached within 180 minutes. Biosorption kinetics has been described by Lagergren equation and biosorption isotherms by classical Langmuir and Freundlich models. Equilibrium data were found to fit well with the Langmuir and Freundlich models, and the maximum monolayer biosorption capacity was 29.41 mg g^?1 of AB25 onto BGFS. The kinetic studies indicated that the pseudo-second-order (PSO) model fitted the experimental data well. In addition, thermodynamic parameters have been calculated. The biosorption process was spontaneous and exothermic in nature with negative values of ΔG° (?1.6031 to ?0.1089 kJ mol^?1) and ΔH° (?16.7920 kJ mol^?1). The negative ΔG° indicates the feasibility of physical biosorption process. The results indicate that BGFS could be used as an eco-friendly and cost-effective biosorbent for the removal of AB25 from aqueous solution.     

Biosynthesis and Uptake of Copper Nanoparticles by Dead Biomass of Hypocrea lixii Isolated from the Metal Mine in the Brazilian Amazon Region

A biological system for the biosynthesis of nanoparticles (NPs) and uptake of copper from wastewater, using dead biomass of Hypocrea lixii was analyzed and described for the first time. The equilibrium and kinetics investigation of the biosorption of copper onto dead, dried and live biomass of fungus were performed as a function of initial metal concentration, pH, temperature, agitation and inoculum volume. The high biosorption capacity was observed for dead biomass, completed within 60 min of contact, at pH 5.0, temperature of 40°C and agitation speed of 150 rpm with a maximum copper biosorption of 19.0 mg g⁻¹. The equilibrium data were better described using the Langmuir isotherm and kinetic analysis indicated that copper biosorption follows a pseudo-second-order model. The average size, morphology and location of NPs biosynthesized by the fungus were determined by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS) and transmission electron microscopy (TEM). NPs were mainly spherical, with an average size of 24.5 nm, and were synthesized extracellularly. The X-ray diffraction (XRD) analysis confirms the presence of metallic copper particles. Infrared spectroscopy (FTIR) study revealed that the amide groups interact with the particles, which was accountable for the stability of NPs. This method further confirmed the presence of proteins as stabilizing and capping agents surrounding the copper NPs. These studies demonstrate that dead biomass of Hypocrea lixii provides an economic and technically feasible option for bioremediation of wastewater and is a potential candidate for industrial-scale production of copper NPs.     

Anilofos Tolerance and Its Mineralization by the Cyanobacterium Synechocystis sp. Strain PUPCCC 64

This study deals with anilofos tolerance and its mineralization by the common rice field cyanobacterium Synechocystis sp. strain PUPCCC 64. The organism tolerated anilofos up to 25 mg L⁻¹. The herbicide caused inhibitory effects on photosynthetic pigments of the test organism in a dose-dependent manner. The organism exhibited 60, 89, 96, 85 and 79% decrease in chlorophyll a, carotenoids, phycocyanin, allophycocyanin and phycoerythrin, respectively, in 20 mg L⁻¹ anilofos on day six. Activities of superoxide dismutase, catalase and peroxidase increased by 1.04 to 1.80 times over control cultures in presence of 20 mg L⁻¹ anilofos. Glutathione content decreased by 26% while proline content was unaffected by 20 mg L⁻¹ anilofos. The test organism showed intracellular uptake and metabolized the herbicide. Uptake of herbicide by test organism was fast during initial six hours followed by slow uptake until 120 hours. The organism exhibited maximum anilofos removal at 100 mg protein L⁻¹, pH 8.0 and 30°C. Its growth in phosphate deficient basal medium in the presence of anilofos (2.5 mg L⁻¹) indicated that herbicide was used by the strain PUPCCC 64 as a source of phosphate.