Broth recycle in a yeast fermentation

Fermentation is a water-intensive process requiring treatment of large amounts of effluent broth. It is desirable to increase the ratio of product produced to the volume of effluent by minimizing the discharge of effluent from the fermentation process. A study of recycling spent fermentation process. A study of recycling spent fermentation broth for the subsequent fermentation was carried out with Apiotrichum curvatum an oleaginous yeast, as the working culture. Spent broth from a defined medium was recycled t replace as much as 75% of the water and salts for subsequent batches and this was repeated for seven sequential batches without affecting cell mass and lipid production. A 64% vlume reduction of wastewater was achieved in this manner. However, when using whey permeate as the medium, lipid production dropped after three consecutive recycle operations at 50% recycle, and after two consecutive recycle operations at 75% and 100% recycle. Accumulation of ions in the broth appeared to be responsible for the inhibition. An ion exchange step was able to eliminate the ion buildup and restore fermentation performance. (c) 1994 John Wiley & Sons, Inc.     

Lactic acid fermentation in a recycle batch reactor using immobilized Lactobacillus casei

Lactic acid production by recycle batch fermentation using immobilized cells of Lactobacillus casei subsp. rhamnosus was studied. The culture medium was composed of whey treated with an endoprotease, and supplemented with 2.5 g/L of yeast extract and 0.18 mM Mn(2+) ions. The fermentation set-up comprised of a column packed with polyethyleneimine-coated foam glass particles, Pora-bact A, and connected with recirculation to a stirred tank reactor vessel for pH control. The immobilization of L. casei was performed simply by circulating the culture medium inoculated with the organism over the beads. At this stage, a long lag period preceded the cell growth and lactic acid production. Subsequently, for recycle batch fermentations using the immobilized cells, the reducing sugar concentration of the medium was increased to 100 g/L by addition of glucose. The lactic acid production started immediately after onset of fermentation and the average reactor productivity during repeated cycles was about 4.3 to 4.6 g/L . h, with complete substrate utilization and more than 90% product yield. Sugar consumption and lactate yield were maintained at the same level with increase in medium volume up to at least 10 times that of the immobilized biocatalyst. The liberation of significant amounts of cells into the medium limited the number of fermentation cycles possible in a recycle batch mode. Use of lower yeast extract concentration reduced the amount of suspended biomass without significant change in productivity, thereby also increasing the number of fermentation cycles, and even maintained the D-lactate amount at low levels. The product was recovered from the clarified and decolorized broth by ion-exchange adsorption. (c) 1997 John Wiley & Sons, Inc. Biotechnol Bioeng 55:841-853, 1997.     

Fermentation and recovery of glutamic acid from palm waste hydrolysate by Ion-exchange resin column

Glutamic acid produced from palm waste hydrolysate by fermentation with Brevibacterium lactofermentum ATCC 13869 is produced with a remarkably high yield compared with that produced from pure glucose as a carbon source. The produce yield is 70 g/L with glucose, wherease, when palm waste hydrolysate is the fermentation medium in the same bioreactor under same conditions, it is 88 g/L. The higher yield may be attributed to the fact that this organism has the ability to convert sugars other than only glucose present in the hydrolysate. Bioreactor conditions most conducive for maximum production are pH 7.5, temperature of 30 degrees rmentation period of 48 h, inoculum size 6%, substrate concentration of 10 g per 100 mL, yeast extract 0.5 g per 100 mL as a suitable N source, and biotin at a concentration of 10 pg/L. Palm waste hydrolysate used in this study was prepared by enzymic saccharification of treated palm press fiber under conditions that yielded a maximum of 30 g/L total reducing sugars. Glutamic acid from fermentation broth was recovered by using a chromatographic column (5cm x 60 cm) packed with a strong ion-exchange resin. The filtered broth containing glutamic acid and other inorganic ions was fed to the fully charged column. The broth was continuously recycled at a flow rate of 50 mL/min (retention time of 55 min) until glutamic acid was fully adsorbed on the column leaving other ions in the effluent. Recovery was done by eluting with urea and sodium hydroxide for total displacement of glutamic acid from the resin. The eluent containing 88 g/L of glutamic acid was concentrated by evaporation to obtain solid crystals of the product. (c) 1995 John Wiley & Sons, Inc.     

Incorporating hydrodynamics into spatiotemporal metabolic models of bubble column gas fermentation

Gas fermentation has emerged as a technologically and economically attractive option for producing renewable fuels and chemicals from carbon monoxide (CO) rich waste streams. LanzaTech has developed a proprietary strain of the gas fermentating acetogen Clostridium autoethanogenum as a microbial platform for synthesizing ethanol, 2,3-butanediol, and other chemicals. Bubble column reactor technology is being developed for the large-scale production, motivating the investigation of multiphase reactor hydrodynamics. In this study, we combined hydrodynamics with a genome-scale reconstruction of C. autoethanogenum metabolism and multiphase convection–dispersion equations to compare the performance of bubble column reactors with and without liquid recycle. For both reactor configurations, hydrodynamics was predicted to diminish bubble column performance with respect to CO conversion, biomass production, and ethanol production when compared with bubble column models in which the gas phase was modeled as ideal plug flow plus axial dispersion. Liquid recycle was predicted to be advantageous by increasing CO conversion, biomass production, and ethanol and 2,3-butanediol production compared with the non-recycle reactor configuration. Parametric studies performed for the liquid recycle configuration with two-phase hydrodynamics showed that increased CO feed flow rates (more gas supply), smaller CO gas bubbles (more gas–liquid mass transfer), and shorter column heights (more gas per volume of liquid per time) favored ethanol production over acetate production. Our computational results demonstrate the power of combining cellular metabolic models and two-phase hydrodynamics for simulating and optimizing gas fermentation reactors.     

A novel recycle batch immobilized cell bioreactor for propionate production from whey lactose

Recycle batch fermentations using immobilized cells of Propionibacterium acidipropionici were studied for propionate production from whey permeate, de-lactose whey permeate, and acid whey. Cells were immobilized in a spirally wound fibrous sheet packed in a 0.5-L column reactor, which was connected to a 5-L stirred tank batch fermentor with recirculation. The immobilized cells bioreactor served as a breeder for these recycle batch fermentations. High fermentation rates and conversions were obtained with these whey media without nutrient supplementation. It took approximately 55 h to ferment whey permeate containing approximately 45 g/L lactose to approximately 20 g/L propionic acid. Higher propionate concentrations can be produced with various concentrated whey media containing more lactose. The highest propionic acid concentration obtained with the recycle batch reactor was 65 g/L, which is much higher than the normal maximum concentration of 35 to 45 g/L reported in the literature. The volumetric productivity ranged from 0.22 g/L . h to 0.47 g/L . h, depending on the propionate concentration and whey medium used. The corresponding specific cell productivity was 0.033 to 0.07 g/L . g cell. The productivity increased to 0.68 g/L . h when whey permeate was supplemented with 1% (w/v) yeast extract. Compared with conventional batch fermentation, the recycle batch fermentation with the immobilized cell bioreactor allows faster fermentation, produces a higher concentration of product, and can be run continually without significant downtime. The process also produced similar fermentation results with nonsterile whey media. (c) 1995 John Wiley & Sons, Inc.     

Integration of Gas Enhanced Oil Recovery in Multiphase Fermentations for the Microbial Production of Fuels and Chemicals

In multiphase fermentations where the product forms a second liquid phase or where solvents are added for product extraction, turbulent conditions disperse the oil phase as droplets. Surface‐active components (SACs) present in the fermentation broth can stabilize the product droplets thus forming an emulsion. Breaking this emulsion increases process complexity and consequently the production cost. In previous works, it has been proposed to promote demulsification of oil/supernatant emulsions in an off‐line batch bubble column operating at low gas flow rate. The aim of this study is to test the performance of this recovery method integrated to a fermentation, allowing for continuous removal of the oil phase. A 500 mL bubble column is successfully integrated with a 2 L reactor during 24 h without affecting cell growth or cell viability. However, higher levels of surfactants and emulsion stability are measured in the integrated system compared to a base case, reducing its capacity for oil recovery. This is related to release of SACs due to cellular stress when circulating through the recovery column. Therefore, it is concluded that the gas bubble‐induced oil recovery method allows for oil separation and cell recycling without compromising fermentation performance; however, tuning of the column parameters considering increased levels of SACs due to cellular stress is required for improving oil recovery.     

A rapid and simplified extraction method of erythromycin from fermentation broth with bond elut C18 cartridge for analysis by HPLC

Solid phase extraction of erythromycin from fermentation broth is described in this paper. This method results in 85 percent recovery of erythromycin A with a batch to batch variability of less than 3 percent. Each column can be used twice with 2-3% loss of recovery. The columns are regenerated immediately after each extraction. In comparison with liquid liquid extraction, solid phase extracts are cleaner, the method is less time consuming and exposure to hazardous solvents is reduced.     

三相鼓泡塔生物反应器培养云芝菌合成漆酶

为了提高云芝菌发酵生产漆酶的效率,提出了一种利用自絮凝菌丝球在三相鼓泡塔生物反应器中重复分批发酵产漆酶的新方法。在优化后的产酶条件下,考察维生素C的添加浓度对漆酶活力的影响,并通过在培养基中添加维生素C进行漆酶多批次培养。研究结果表明,维生素C的添加浓度为1.50mmol/L时,可使漆酶活力提高2.6倍。连续进行了10批培养,每批最大漆酶的活力均在1000 U/mL以上,最高酶活出现在第五批为1919.6 U/mL,总培养时间达25 d。此方法所得漆酶对染料靛蓝具有明显的脱色降解作用,在介体1-羟基苯并三唑（HBT）用量0.10%,漆酶用量100 U/L条件下作用40 min时,靛蓝脱色率达到96.7%。该方法采用的三相鼓泡塔生物反应器性能稳定、菌丝球可重复使用,该方法有利于漆酶的高效、规模化生产。     

Process design and economic studies of alternative fermentation methods for the production of ethanol

Cell recycle and vacuum fermentation processes are described for the continuous production of ethanol. Preliminary process design studies are employed to make an economic comparison of these alternative fermentation schemes with continuous and batch fermentation technologies. Designs are based on a production capacity of 78,000 gal 95% ethanol (EtOH)/day employing molasses as the fermentation substrate. The studies indicate that a 57% reduction in fixed capital investment is realized by continuous rather than batch operation. Further decreases in required capital investment of 68 and 71% over batch fermentation were obtained for cell recycle and vacuum operation, respectively. However, ethanol production costs were dominated by the cost of molasses, representing over 75% of the total manufacturing cost. But, when a reasonable yeast by-product credit was assumed, the net production cost for 95% ethanol was estimated at 82.3 and 80.6 cent/gal, for the cell recycle and vacuum processes, respectively.     

In situ extractive fermentation of acetone and butanol

The productivity of the acetone-butanol fermentation was increased by continuously removing acetone and butanol from the fermentation broth during fed-batch culture. Whole broth containing viable cells of Clostridium acetobutylicum was cycled to a Karr reciprocating plate extraction column in which acetone and butanol were extracted into oleyl alcohol flowing counter-currently through the column. By continuously removing these toxic metabolites from the broth, end product inhibition was reduced, and a concentrated feed solution containing 300 g/L glucose was fermented at an overall butanol productivity of 1.0 g/L h, 70% higher than the productivity of normal batch fermentation. The continuous extraction process provides flexible operation and lends itself to process scale-up.     

自絮凝颗粒酵母酒精高浓度连续发酵的研究

在四釜串联气升环流悬浮床生物反应器系统中 ,进行了絮凝颗粒酵母酒精连续发酵的研究。以CO2 为驱动动力 ,发酵液液蒸馏废液全循环 ,稀释率为 0 2 h。发酵成熟醑酒精平均浓度为 96 6g L ,残余还原糖和总糖分别为 1 2g L和 4 1g L。     

Studies on the interaction of fermentation and microfiltration operations: erythromycin recovery from Saccharopolyspora erythraea fermentation broths

Changes in fermentation media not only affect the performance of the fermentation itself (with regard to the kinetics of biomass and product formation and the yields obtained) but also the initial product-recovery operations downstream of the fermentor. In this work, microfiltration experiments to remove Saccharopolyspora erythraea biomass from fermentation broth and to recover erythromycin were carried out using two fundamentally different media; a soluble complex medium (SCM) and an oil-based process medium (OBM). Small-scale batch fermentations of 14-L working volume were carried out in triplicate using both media. Broth samples were taken from each fermentation at regular intervals from the end of the exponential-growth phase onwards. These were then processed using a Minitan II (acrylic), tangential crossflow-filtration module, fitted with a single 60 cm(2) Durapore hydrophilic 0.2 microm membrane, operated in concentration mode. The OBM fermentations produced higher titers of erythromycin but required longer fermentation times due to increased lag phases and slower maximum-growth rates. The OBM also increased the loading on the membrane; at maximum product titers residual oil concentrations of 3 g. L(-1), antifoam concentrations of 2 g. L(-1) and flour concentrations estimated at approximately 10 g/L(-1) were typical. It was found that both the permeate flux and erythromycin transmission were affected by the choice of medium. The OBM had significantly lower values for both parameters (12.8 Lm(-2) h(-1) and 89.6% respectively) than the SCM (35.9 Lm(-2) h(-1) and 96.7% respectively) when the fermentations were harvested at maximum erythromycin titers. Transmission of erythromycin stayed approximately constant as a function of fermentation time for both media, however, for the OBM the permeate flux decreased with time which correlated with an increase in broth viscosity. The relatively poor microfiltration performance of the OBM medium was, however, offset by the higher titers of erythromycin that were achieved during the fermentation. The filtration characteristics of the SCM broth did not show any correlation with either broth viscosity or fermentation time. Image-analysis data suggested that there was a correlation between hyphal morphology (main hyphal length) and permeate flux (no such correlation was found for the OBM broth). Moreover, it has been shown for the OBM broth that the residual flour had a profound effect on the microfiltration characteristics. The influence of the residual flour was greater than that imposed by the morphology and concentration of the biomass. The understanding of the factors governing the interaction of the fermentation and microfiltration operations obtained in this work provides a first step towards optimization of the overall process sequence.     

Heterolactic fermentation by a homofermentative Lactobacillus sp. during glucose limitation in anaerobic continuous culture with complete cell recycle

E. BORCH, H. BERG AND O. HOLST. 1991. The homofermentative Lactobacillus sp. 93 SMRICC 235 was grown anaerobically in batch culture and subsequent continuous culture, with complete cell recycle at pH 6.0 and 25^.C, on a semi-defined medium. During cell recycle culture the biomass was concentrated in the fermenter to a final dry weight of 37 g/1 and a viable count of 10.6 log cfu/ml. The corresponding final values in batch culture were 2.4 g/1 and 9.3 log cfu/ml. A switch from homo- to heterolactic fermentation was observed during starvation, due to glucose depletion in the cell recycle culture. High levels of acetate and formate were produced in addition to ethanol. Amino acid profiles of hydrolysed samples showed extensive utilization of amino acids, particularly in cell recycle culture. Sulphide was produced during cell recycle culture. The change from homo- to heterolactic fermentation observed during semi-starvation is likely to affect the properties of lactobacilli as spoilage bacteria of meat and meat products, as well as starter cultures.     

Design of a lamella settler for biomass recycling in continuous ethanol fermentation process

The design and application of a settler to a continuous fermentation process with yeast recycle were studied. The compact lamella-type settler was chosen to avoid large volumes associated with conventional settling tanks. A rationale of the design method is covered. The sedimentation area was determined by classical batch settling rate tests and sedimentation capacity calculation. Limitations on the residence time of the microorganisms in the settler, rather than sludge thickening considerations, was the approach employed for volume calculation. Fermentation rate tests with yeast after different sedimentation periods were carried out to define a suitable residence time. Continuous cell recycle fermentation runs, performed with the old and new sedimentation devices, show that lamella settler improves biomass recycling efficiency, being the process able to operate at higher sugar concentrations and faster dilution rates.     

Enhanced acetone-butanol fermentation using repeated fed-batch operation coupled with cell recycle by membrane and simultaneous removal of inhibitory products by adsorption

A novel acetone-butanol production process was developed which integrates a repeated fed-batch fermentation with continuous product removal and cell recycle. The inhibitory product concentrations of the fermentation by Clostridium acetobutylicum were reduced by the simultaneous extraction process using polyvinylpyridine (PVP) as an adsorbent. Because of the reduced inhibition effect, a higher specific cell growth rate and thus a higher product formation rate was achieved. The cell recycle using membrane separation increased the total cell mass density and, therefore, enhanced the reactor productivity. The repeated fed-batchoperation overcame the drawbacks typically associated with a batch operation such as down times, long lag period, and the limitation on the maximum initial substrate concentration allowed due to the substrate inhibition. Unlike a continuous operation, the repeated fed-batch operation could beoperated for a long time at a relatively higher substrate concentration without sacrificing the substrate loss in the effluent. As a result, the integrated process reached 47.2 g/L in the equivalent solvent concentration (including acetone, butanol, and ethanol) and 1.69 g/L . h in the fermentor productivity, on average, over a 239.5-h period. Compared with a controlled traditional batch acetone-butanol fermentation, the equivalent solvent concentration and the tormentor productivity were increased by 140% and 320%, respectively. (c) 1995 John Wiley & Sons Inc.     

A media design program for lactic acid production coupled with extraction by electrodialysis

The aim of this study was to investigate industrial media for lactic acid fermentation to reduce the cost of nitrogen sources. Corn steep liquor (CSL) was successfully used at 5% (v/v) in batch fermentations. Use of soluble CSL improved the productivity approximately 20% with an advantage of clearer fermentation broth. Yeast extract (YE)-complemented CSL media further increased the productivity. It was found that 3.1 g L(-1) yeast extract and 5% CSL could be an effective substitute for 15 g L(-1) yeast extract in 10% glucose medium. Spent brewery yeast was also used as a sole nitrogen source equivalent to 5% CSL. Lactic acid was recovered by electrodialysis from the cell free broth. Depleted cell free broth supplemented with 5 g L(-1) of yeast extract performed reasonably in batch cultures. Reuse of the fermentation broth may reduce the cost of raw materials as well as minimize the fermentation wastes.     

Production of citric acid using its extraction wastewater treated by anaerobic digestion and ion exchange in an integrated citric acid-methane fermentation process

In order to solve the problem of extraction wastewater pollution in citric acid industry, an integrated citric acid-methane fermentation process is proposed in this study. Extraction wastewater was treated by mesophilic anaerobic digestion and then used to make mash for the next batch of citric acid fermentation. The recycling process was done for seven batches. Citric acid production (82.4 g/L on average) decreased by 34.1?% in the recycling batches (2nd–7th) compared with the first batch. And the residual reducing sugar exceeded 40 g/L on average in the recycling batches. Pigment substances, acetic acid, ammonium, and metal ions in anaerobic digestion effluent (ADE) were considered to be the inhibitors, and their effects on the fermentation were studied. Results indicated that ammonium, Na⁺ and K⁺ in the ADE significantly inhibited citric acid fermentation. Therefore, the ADE was treated by acidic cation exchange resin prior to reuse to make mash for citric acid fermentation. The recycling process was performed for ten batches, and citric acid productions in the recycling batches were 126.6 g/L on average, increasing by 1.7 % compared with the first batch. This process could eliminate extraction wastewater discharge and reduce water resource consumption.     

Increased xylitol production rate during long-term cell recycle fermentation of Candida tropicalis

Long-term cell recycle fermentations of Candida tropicalis were performed over 14 rounds of fermentation. The average xylitol concentrations, fermentation times, volumetric productivities and product yields for 14 rounds were 105 g l^–1, 333 h, 4.4 g l^–1 h^–1 and 78%, respectively, in complex medium; and 110 g l^–1, 284 h, 5.4 g l^–1 h^–1 and 81%, respectively, in a chemically defined medium. These productivities were 1.7 and 2.4 times those with batch fermentation in the complex and chemically defined media, respectively. The xylitol yield from xylose with cell recycle fermentation using the chemically defined medium was 81% (w/w), which was 7% greater than the xylitol yield with batch fermentation (74%); both modes of fermentation gave the same yield using the complex medium. These results suggest that the chemically defined medium is more suitable for production of xylitol than complex medium.     

Recycle in fermentation processes

Until recently, the recycle of the solid (microbial), liquid, or gaseous phases in microbiological processes has only been practiced rarely, with the notable exception of activated sludge processes for wastewater treatment, where recycling of a large fraction of the microbial phase is essential for process stability and performance. During the last decade, the economic impact of a number of politically motivated changes with respect to energy and feedstock costs and availability, and legislation directed towards markedly higher levels of environmental protection have encouraged the evaluation and subsequent development of recycle technology in the fermentation industry. Many of the developments have occurred in isolation and some have failed to result in either an improvement in process economics or any reduction in the quantity of pollutants discharged. This article seeks to review the present diversity of approaches to recycle technology in fermentation processes in order to provide a sensible basis for future developments.     

A repeated batch process for cultivation of <Emphasis Type="Italic">Bifidobacterium longum</Emphasis>

A repeated batch process was performed to culture Bifidobacterium longum CCRC 14634. An on-line device, oxidation-reduction potential (ORP), was used to monitor cell growth and uptake of nutrients in the culture. The ORP of the culture medium decreased substantially during fermentation until nutrients were depleted. Six cycles of batch fermentation using ORP as a control parameter were successfully carried out. As soon as ORP remained constant or increased, three-quarters of the broth was removed, and the same volume of fresh medium was fed to the fermenter for a new cycle of cultivation. Average cell concentrations of 1.9×10⁹ and 3.4×10⁹ cfu ml^–1 for repeated batch fermentation in MRS (Lactobacilli MRS broth) and WY (containing whey hydrolyzates, yeast extract, l-cysteine) medium, respectively, were achieved. Cell mass productivities for batch, fed-batch and repeated batch fermentation using MRS medium were 0.51, 0.41, and 0.64 g l^–1 h^–1, respectively, and those for batch and repeated batch using WY medium were 0.76, 0.99 g l^–1 h^–1, respectively. The results indicate a possible industrial process to culture Bifidobacteria sp.