Optimization of erythritol production by Candida magnoliae in fed-batch culture

A two-stage fed-batch process was designed to enhance erythritol productivity by the mutant strain of Candida magnoliae. The first stage (or growth stage) was performed in the fed-batch mode where the growth medium was fed when the pH of the culture broth dropped below 4.5. The second stage (or production stage) was started with addition of glucose powder into the culture broth when the cell mass reached about 75 g dry cell weight l⁻¹. When the initial glucose concentration was adjusted to 400 g l⁻¹ in the production stage, 2.8 g l⁻¹ h⁻¹ of overall erythritol productivity and 41% of erythritol conversion yield were achieved, which represented a fivefold increase in erythritol productivity compared with the simple batch fermentation process. A high glucose concentration in the production phase resulted in formation of organic acids including citrate and butyrate. An increase in dissolved oxygen level caused formation of gluconic acid instead of citric acid. Journal of Industrial Microbiology & Biotechnology (2000) 25, 100–103. Received 25 February 2000/ Accepted in revised form 08 June 2000     

Optimization of fed-batch fermentation for xylitol production by Candida tropicalis

Xylitol, a functional sweetener, was produced from xylose by biological conversion using Candida tropicalis ATCC 13803. Based on a two-substrate fermentation using glucose for cell growth and xylose for xylitol production, fed-batch fermentations were undertaken to increase the final xylitol concentration. The effects of xylose and xylitol on xylitol production rate were studied to determine the optimum concentrations for fed-batch fermentation. Xylose concentration in the medium (100 g l⁻¹) and less than 200 g l⁻¹ total xylose plus xylitol concentration were determined as optimum for maximum xylitol production rate and xylitol yield. Increasing the concentrations of xylose and xylitol decreased the rate and yield of xylitol production and the specific cell growth rate, probably because of an increase in osmotic stress that would interfere with xylose transport, xylitol flux to secretion to cell metabolism. The feeding rate of xylose solution during the fed-batch mode of operation was determined by using the mass balance equations and kinetic parameters involved in the equations in order to increase final xylitol concentration without affecting xylitol and productivity. The optimized fed-batch fermentation resulted in 187 g l⁻¹ xylitol concentration, 0.75 g xylitol g xylose⁻¹ xylitol yield and 3.9 g xylitol l⁻¹ h⁻¹ volumetric productivity. Journal of Industrial Microbiology & Biotechnology (2002) 29, 16–19 doi:10.1038/sj.jim.7000257 Received 15 October 2001/ Accepted in revised form 30 March 2002     

Effects of methanol on expression of an anticoagulant hirudin in recombinant Hansenula polymorpha

A series of batch, fed-batch, and continuous cultures was carried out to analyze the effects of methanol on the fermentation characteristics of recombinant Hansenula polymorpha for the production of hirudin, an anticoagulant. Hirudin expression efficiencies were greatly influenced by the methanol concentrations in continuous and fed-batch culture modes. At a steady state of continuous culture, an optimum methanol concentration of 1.7 g l⁻¹ was determined at a dilution rate of 0.18 h⁻¹ with 1.8 mg l⁻¹ h⁻¹ hirudin productivity. Journal of Industrial Microbiology & Biotechnology (2001) 27, 58–61. Received 21 September 2000/ Accepted in revised form 10 June 2001     

Increase of lycopene production by supplementing auxiliary carbon sources in metabolically engineered <Emphasis Type="Italic">Escherichia coli</Emphasis>

In the fed-batch culture of glycerol using a metabolically engineered strain of Escherichia coli, supplementation with glucose as an auxiliary carbon source increased lycopene production due to a significant increase in cell mass, despite a reduction in specific lycopene content. l-Arabinose supplementation increased lycopene production due to increases in cell mass and specific lycopene content. Supplementation with both glucose and l-arabinose increased lycopene production significantly due to the synergistic effect of the two sugars. Cell growth by the consumption of carbon sources was related to endogenous metabolism in the host E. coli. Supplementation with l-arabinose stimulated only the mevalonate pathway for lycopene biosynthesis and supplementation with both glucose and l-arabinose stimulated synergistically only the mevalonate pathway. In the fed-batch culture of glycerol with 10 g l⁻¹ glucose and 7.5 g l⁻¹ l-arabinose, the cell mass, lycopene concentration, specific lycopene content, and lycopene productivity after 34 h were 42 g l⁻¹, 1,350 mg l⁻¹, 32 mg g cells⁻¹, and 40 mg l⁻¹ h⁻¹, respectively. These values were 3.9-, 7.1-, 1.9-, and 11.7-fold higher than those without the auxiliary carbon sources, respectively. This is the highest reported concentration and productivity of lycopene.     

Evaluation ofl-lactic acid production in batch, fed-batch, and continuous cultures ofRhizopus sp. MK-96-1196 using an airlift bioreactor

Various processes which producel-lactic acid using ammonia-tolerant mutant strain,Rhizopus sp. MK-96-1196, in a 3 L airlift bioreactor were evaluated. When the fed-batch culture was carried out by keeping the glucose concentration at 30 g/l, more than 140 g/l ofl-lactic acid was produced with a product yield of 83%. In the case of the batch culture with 200 g/l of initial glucose concentration, 121 g/L ofl-lactic acid was obtained but the low product yield based on the amount of glucose consumed. In the case of a continuous culture, 1.5 g/l/h of the volumetric productivity with a product yield of 71% was achieved at dilution rate of 0.024 h⁻¹. Basis on these results three processes were evaluated by simple variable cost estimation including carbon source, steam, and waste treatment costs. The total variable costs of the fed-batch and continuous cultures were 88% and 140%, respectively, compared to that of batch culture. The fed-batch culture with highl-lactic acid concentration and high product yield decreased variable costs, and was the best-suited for the industrial production ofl-lactic acid.     

Microbial production of 1,3-propanediol from glycerol by Klebsiella pneumoniae under micro-aerobic conditions up to a pilot scale

1,3-Propanediol (1,3-PD) can be produced from glycerol by Klebsiella pneumoniae under micro-aerobic conditions. Recently, this fed-batch fermentation process has been successfully scaled up to 1 m³. The final 1,3-PD concentration, molar yield and volumetric productivity of 72 g l⁻¹, 57% and 2.1 g l⁻¹ h⁻¹, respectively, are close to those of 75 g l⁻¹, 61%, and 2.2 g l⁻¹ h⁻¹ under anaerobic conditions. This process would be suitable for the production of 1,3-PD on a large scale.     

Production of 1,3-propanediol by Klebsiella pneumoniae from glycerol broth

Broth containing 152 g glycerol l⁻¹ from Candida krusei culture was converted to 1,3-propanediol by Klebsiella pneumoniae. Residual glucose in the broth promoted growth of K. pneumoniae while acetate was inhibitory. After desalination treatment of glycerol broth by electrodialysis, the acetate in the broth was removed. A fed-batch culture with electrodialytically pretreated broth as␣substrate was developed giving 53 g 1,3- propanediol l⁻¹ with a yield of 0.41 g g⁻¹ glycerol and a productivity of 0.94 g l⁻¹ h⁻¹.     

Lipid production by <Emphasis Type="Italic">Rhodosporidium toruloides</Emphasis> Y4 using different substrate feeding strategies

Microbial lipid is a potential alternative feedstock for the biodiesel industry. New culture strategies remain to be developed to improve the economics of microbial lipid technology. This work describes lipid production by the oleaginous yeast Rhodosporidium toruloides Y4 using a 15-l bioreactor with different substrate feeding strategies. Among these strategies, the intermittent feeding mode gave a lipid productivity of 0.36 g l⁻¹ h⁻¹, whereas the constant glucose concentration II (CC-II) mode gave the highest lipid productivity of 0.57 g l⁻¹ h⁻¹. The repeated fed-batch mode according to the CC-II mode was performed with a duration time of 358 h, and the overall lipid productivity was 0.55 g l⁻¹ h⁻¹. Our results suggested that substrate feeding modes had a great impact on lipid productivity and that the repeated fed-batch process was the most appealing method by which to enhance microbial lipid production.     

Lactic acid production from cellulosic waste by immobilized cells of Lactobacillus delbrueckii

Industrial waste corn cob residue (from xylose manufacturing) without pretreatment was hydrolyzed by cellulase and cellobiase. The cellulosic hydrolysate contained 52.4 g l⁻¹ of glucose and was used as carbon source for lactic acid fermentation by cells of Lactobacillus delbrueckii ZU-S2 immobilized in calcium alginate gel beads. The final concentration of lactic acid and the yield of lactic acid from glucose were 48.7 g l⁻¹ and 95.2%, respectively, which were comparative to the results of pure glucose fermentation. The immobilized cells were quite stable and reusable, and the average yield of lactic acid from glucose in the hydrolysate was 95.0% in 12 repeated batches of fermentation. The suitable dilution rate of continuous fermentation process was 0.13 h⁻¹, and the yield of lactic acid from glucose and the productivity were 92.4% and 5.746 g l⁻¹ h⁻¹, respectively. The production of lactic acid by simultaneous saccharification and fermentation (SSF) process was carried out in a coupling bioreactor, the final concentration of lactic acid was 55.6 g l⁻¹, the conversion efficiency of lactic acid from cellulose was 91.3% and the productivity was 0.927 g l⁻¹ h⁻¹. By using fed-batch technique in the SSF process, the final concentration of lactic acid and the productivity increased to 107.6 g l⁻¹ and 1.345 g l⁻¹ h⁻¹, respectively, while the dosage of cellulase per gram substrate decreased greatly. This research work should advance the bioconversion of renewable cellulosic resources and reduce environmental pollution.     

Batch and repeated batch production of l(+)-lactic acid by Enterococcus faecalis RKY1 using wood hydrolyzate and corn steep liquor

Lactic acid production was investigated for batch and repeated batch cultures of Enterococcus faecalis RKY1, using wood hydrolyzate and corn steep liquor. When wood hydrolyzate (equivalent to 50 g l⁻¹ glucose) supplemented with 15–60 g l⁻¹ corn steep liquor was used as a raw material for fermentation, up to 48.6 g l⁻¹ of lactic acid was produced with, volumetric productivities ranging between 0.8 and 1.4 g l⁻¹ h⁻¹. When a medium containing wood hydrolyzate and 15 g l⁻¹ corn steep liquor was supplemented with 1.5 g l⁻¹ yeast extract, we observed 1.9-fold and 1.6-fold increases in lactic acid productivity and cell growth, respectively. In this case, the nitrogen source cost for producing 1 kg lactic acid can be reduced to 23% of that for fermentation from wood hydrolyzate using 15 g l⁻¹ yeast extract as a single nitrogen source. In addition, lactic acid productivity could be maximized by conducting a cell-recycle repeated batch culture of E. faecalis RKY1. The maximum productivity for this process was determined to be 4.0 g l⁻¹ h⁻¹.     

Production of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) by Cupriavidus necator from waste rapeseed oil using propanol as a precursor of 3-hydroxyvalerate

Waste rapeseed oil is a useful substrate for polyhydroxyalkanoates (PHA) production employing Cupriavidus necator H16. In fed-batch mode, we obtained biomass and PHA yields of 138 and 105 g l⁻¹, respectively. Yield coefficient and volumetric productivity were 0.83 g PHA per g oil and 1.46 g l⁻¹ h⁻¹, respectively. Propanol at 1% (v/v) enhanced both PHA and biomass formation significantly and, furthermore, resulted in incorporation of 3-hydroxyvalerate units into PHA structure. Thus, propanol can be used as an effective precursor of 3-hydroxyvalarete for production of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) copolymer. During the fed-batch cultivation, propanol concentration was maintained at 1% which resulted in 8% content of 3-hydroxyvalerate in copolymer.     

Production of lipase by high cell density fed-batch culture of Candida cylindracea

Candida cylindracea NRRL Y-17506 was grown to produce extracellular lipase from oleic acid as a carbon source. Through flask cultures, it was found that the optimum initial oleic acid concentration for cell growth was 20 g l⁻¹. However, high initial concentrations of oleic acid up to 50 g l⁻¹ were not inhibitory. The highest extracellular lipase activity obtained in flask culture was 3.0 U ml⁻¹ after 48 h with 5 g l⁻¹ of initial oleic acid concentration. Fed-batch cultures (intermittent and stepwise feeding) were carried out to improve cell concentration and lipase activity. For the intermittent feeding fed-batch culture, the final cell concentration was 52 g l⁻¹ and the extracellular lipase activity was 6.3 U ml⁻¹ at 138.5 h. Stepwise feeding fed-batch cultures were carried out to simulate an exponential feeding and to investigate the effects of specific growth rate (0.02, 0.04 and 0.08 h⁻¹) on cell growth and lipase production. The highest final cell concentration obtained was 90 g l⁻¹ when the set point of specific growth rate (μ_set) was 0.02 h⁻¹. High specific growth rate (0.04 and 0.08 h⁻¹) decreased extracellular lipase production in the later part of fed-batch cultures due to build-up of the oleic acid oversupplied. The highest extracellular lipase activity was 23.7 U ml⁻¹ when μ_set was 0.02 h⁻¹, while the highest lipase productivity was 0.31 U ml⁻¹ h⁻¹ at μ_set of 0.08 h⁻¹.     

Optimization of lactic acid production by immobilized <Emphasis Type="Italic">Lactococcus lactis</Emphasis> IO-1

Production of lactic acid from glucose by immobilized cells of Lactococcus lactis IO-1 was investigated using cells that had been immobilized by either entrapment in beads of alginate or encapsulation in microcapsules of alginate membrane. The fermentation process was optimized in shake flasks using the Taguchi method and then further assessed in a production bioreactor. The bioreactor consisted of a packed bed of immobilized cells and its operation involved recycling of the broth through the bed. Both batch and continuous modes of operation of the reactor were investigated. Microencapsulation proved to be the better method of immobilization. For microencapsulated cells at immobilized cell concentration of 5.3 g l⁻¹, the optimal production medium had the following initial concentrations of nutrients (g l⁻¹): glucose 45, yeast extract 10, beef extract 10, peptone 7.5 and calcium chloride 10 at an initial pH of 6.85. Under these conditions, at 37 °C, the volumetric productivity of lactic acid in shake flasks was 1.8 g l⁻¹ h⁻¹. Use of a packed bed of encapsulated cells with recycle of the broth through the bed, increased the volumetric productivity to 4.5 g l⁻¹ h⁻¹. The packed bed could be used in repeated batch runs to produce lactic acid.     

Induction of xylanases by sugar cane bagasse at different cell densities of Cellulomonas flavigena

The effect of cell density on xylanolytic activity and productivity of Cellulomonas flavigena was evaluated under two different culturing conditions: fed-batch culture with discontinuous feed of sugar cane bagasse (SCB; condition 1) and glycerol fed-batch culture followed by addition of SBC as xylanases inducer (condition 2). The enzymatic profile of xylanases was similar in both systems, regardless of the initial cell density at time of induction. However, the xylanolytic activity changed with initial cell density at the time of induction (condition 2). The maximum volumetric xylanase activity increased with increased initial cell density from 4 to 34 g l⁻¹ but decreased above this value. The largest total volumetric xylanase productivity under condition 2 (1.3 IU ml⁻¹ h⁻¹) was significantly greater compared to condition 1 (maximum 0.6 IU ml⁻¹ h⁻¹). Consequently, induction of xylanase activity by SCB after growing of C. flavigena on glycerol at intermediate cell density can be a feasible alternative to improve activity and productivity of xylanolytic enzymes.     

Enhanced 1,3-propanediol production by supply of organic acids and repeated fed-batch culture

In fed-batch culture of Klebsiella pneumoniae, 1,3-propanediol production was growth associated, while the by-products, including lactic acid and ethanol, increased sharply as the cells grew slowly. When the fed-batch culture was supplied with a mixture of organic acids including citrate, fumarate and succinate, cell growth and 1,3-propanediol production increased significantly, whereas the by-products, especially lactic acid and ethanol, decreased sharply. High concentrations of PDO and acetate inhibited cell growth and PDO production. To improve the PDO production, repeated fed-batch culture with addition of the organic acid mixture was performed in a 5-l reactor. The fed-batch culture was repeated five times, and the 1,3-propanediol yield and concentration reached above 0.61 mol mol⁻¹ and 66 g l⁻¹, respectively, in 20 h for each cycle. Furthermore, the PDO productivity reached above 3.30 g l⁻¹ h⁻¹ in each cycle, which was much higher than that of the original fed-batch culture.     

Extracellular production of a glycolipid biosurfactant, mannosylerythritol lipid, by Candida sp. SY16 using fed-batch fermentation

Candida sp. strain SY16 produces a glycolipid-type biosurfactant, mannosylerythritol lipid (MEL-SY16), which can reduce the surface tension of a culture broth from 72 to 30 dyne cm⁻¹ and highly emulsify hydrocarbons when cultured in soybean-oil-containing media. As such, laboratory-scale fermentation for MEL-SY16 production was performed using optimized conditions. In batch fermentation, MEL-SY16 was mainly produced during the stationary phase of growth, and the concentration of MEL-SY16 reached 37 g l⁻¹ after 200 h. The effect of pH control on the production of MEL-SY16 was also examined in batch fermentation. The highest production yield of MEL-SY16 was when the pH was controlled at 4.0, and the production was significantly improved compared to batch fermentation without pH control. In fed-batch fermentation, glucose and soybean oil (1:1, w/w) were used in combination as the initial carbon sources for cell growth, and soybean oil was used as the feeding carbon source during the MEL production phase. The feeding of soybean oil resulted in the disappearance of any foam and a sharp increase in the MEL production until 200 h, at which point the concentration of MEL-SY16 was 95 g l⁻¹. Among the investigated culture systems, the highest MEL-SY16 production and volumetric production rate were achieved with fed-batch fermentation.     

Effect of growth rate on the production of<Emphasis Type="SmallCaps">l</Emphasis>-proline in the fed-batch culture of<Emphasis Type="Italic">Corynebacterium acetoacidophilum</Emphasis>

Corynebacterium acetoacidophilum RYU3161 was cultivated in al-histidine-limited fed-batch culture. To investigate the effect of cell growth on thel-proline production, 5l fed-batch culture was performed using an exponential feeding rate to obtain the specific growth rates (μ) of 0.04, 0.06, 0.08, and 0.1 h⁻¹. The results show that the highest production ofl-proline was obtained at μ=0.04 h⁻¹. The specificl-proline production rate (Q_p) increased proportionally as a function of the specific growth rate, but decreased after it revealed the maximum value at μ=0.08 h⁻¹. Thus, the highest productivity ofl-proline was 1.66 g L⁻¹ h⁻¹ at μ=0.08 h⁻¹. The results show that the production of L-proline inC. acetoacidophilum RYU3161 has mixed growth-associated characteristics.     

Recent advances in ABE fermentation: hyper-butanol producing Clostridium beijerinckii BA101

This is an overview of the mutant strain Clostridium beijerinckii BA101 which produces solvents (acetone–butanol–ethanol, ABE) at elevated levels. This organism expresses high levels of amylases when grown on starch. C. beijerinckii BA101 hydrolyzes starch effectively and produces solvent in the concentration range of 27–29 g l⁻¹. C. beijerinckii BA101 has been characterized for both substrate and butanol inhibition. Supplementing the fermentation medium (MP2) with sodium acetate enhances solvent production to 33 g l⁻¹. The results of studies utilizing commercial fermentation medium and pilot plant-scale reactors are consistent with the results using small-scale reactors. Pervaporation, a technique to recover solvents, has been applied to fed-batch reactors containing C. beijerinckii BA101, and solvent production as high as 165 g l⁻¹ has been achieved. Immobilization of C. beijerinckii BA101 by adsorption and use in a continuous reactor resulted in reactor productivity of 15.8 g l⁻¹ h⁻¹. Recent economic studies employing C. beijerinckii BA101 suggested that butanol can be produced at US$0.20–0.25 lb⁻¹ by employing batch fermentation and distillative recovery. Application of new technologies such as pervaporation, fed-batch culture, and immobilized cell reactors is expected to further reduce these prices. Journal of Industrial Microbiology & Biotechnology (2001) 27, 287–291. Received 12 September 2000/ Accepted in revised form 27 January 2001     

Increase of ethanol productivity by cell-recycle fermentation of flocculating yeast

Using the recombinant flocculating Angel yeast F6, long-term repeated batch fermentation for ethanol production was performed and a high volumetric productivity resulted from half cells not washed and the optimum opportunity of residual glucose 20 g l⁻¹ of last medium. The obtained highest productivity was 2.07 g l⁻¹ h⁻¹, which was improved by 75.4% compared with that of 1.18 g l⁻¹ h⁻¹ in the first batch fermentation. The ethanol concentration reached 8.4% corresponding to the yield of 0.46 g g⁻¹. These results will contribute greatly to the industrial production of fuel ethanol using the commercial method with the flocculating yeast.     

Ethanol production from sweet sorghum juice in batch and fed-batch fermentations by <Emphasis Type="Italic">Saccharomyces cerevisiae</Emphasis>

Sweet sorghum juice supplemented with 0.5% ammonium sulphate was used as a substrate for ethanol production by Saccharomyces cerevisiae TISTR 5048. In batch fermentation, kinetic parameters for ethanol production depended on initial cell and sugar concentrations. The optimum initial cell and sugar concentrations in the batch fermentation were 1 × 10⁸ cells ml⁻¹ and 24 °Bx respectively. At these conditions, ethanol concentration produced (P), yield (Y _ps) and productivity (Q _p ) were 100 g l⁻¹, 0.42 g g⁻¹ and 1.67 g l⁻¹ h⁻¹ respectively. In fed-batch fermentation, the optimum substrate feeding strategy for ethanol production at the initial sugar concentration of 24 °Bx was one-time substrate feeding, where P, Y _ps and Q _p were 120 g l⁻¹, 0.48 g g⁻¹ and 1.11 g l⁻¹ h⁻¹ respectively. These findings suggest that fed-batch fermentation improves the efficiency of ethanol production in terms of ethanol concentration and product yield.