Kinetic and Equilibrium Studies of Cr(VI) Biosorption by Dead <Emphasis Type="Italic">Bacillus licheniformis</Emphasis> Biomass

Many studies have been carried out on the biosorption capacity of different kinds of biomass. However, reports on the kinetic and equilibrium study of the biosorption process are limited. In our experiments, the removal of Cr(VI) from aqueous solution was investigated in a batch system by sorption on the dead cells of Bacillus licheniformis isolated from metal-polluted soils. Equilibrium and kinetic experiments were performed at various initial metal concentrations, pH, contact time, and temperatures. The biomass exhibited the highest Cr(VI) uptake capacity at 50°C, pH 2.5 and with the initial Cr(VI) concentration of 300 mg/g. The Langmuir and Freundlich models were considered to identify the isotherm that could better describe the equilibrium adsorption of Cr(VI) onto biomass. The Langmuir model fitted our experimental data better than the Freundlich model. The suitability of the pseudo first-order and pseudo second-order kinetic models for the sorption of Cr(VI) onto Bacillus licheniformis was also discussed. It is better to apply the pseudo second-kinetic model to describe the sorption system.     

Biosorption characteristics of Aspergillus fumigatus for the decolorization of triphenylmethane dye acid violet 49

This study focuses on the possible use of Aspergillus fumigatus to remove acid violet 49 dye (AV49) from aqueous solution. In batch biosorption experiments, the highest biosorption efficiency was achieved at pH 3.0, with biosorbent dosage of 3.0 gL^?1 within about 30 min at 40 °C. The Langmuir and Freundlich models were able to describe the biosorption equilibrium of AV49 onto fungal biomass with maximum dye uptake capacity 136.98 mg g^?1. Biosorption followed a pseudo-second-order kinetic model with high correlation coefficients (R ²?>?0.99), and the biosorption rate constants increased with increasing temperature. Thermodynamic parameters indicated that the biosorption process was favorable, spontaneous, and endothermic in nature, with insignificant entropy changes. Fourier transform infrared spectroscopy strongly supported the presence of several functional groups responsible for dye–biosorbent interaction. Fungal biomass was regenerated with 0.1 M sodium hydroxide and could be reused a number of times without significant loss of biosorption activity. The effective decolorization of AV49 in simulated conditions indicated the potential use of biomass for the removal of color contaminants from wastewater.     

Bioremediation potential of a widespread industrial biowaste as renewable and sustainable biosorbent for synthetic dye pollution

In this study, a model synthetic azo dye (Basic red 46) bioremoval by Carpinus betulus sawdust as inexpensive, eco-friendly, and sustainable biosorbent from aqueous solution was examined in a batch biosorption system. The effective environmental parameters on the biosorption process, such as the value of pH, amount of biosorbent, initial dye concentration and contact time were optimized using classical test design. The possible dye-biosorbent interaction was determined by Fourier Transform Infrared Spectroscopy (FTIR) and Scanning Electron Microscopy (SEM). The equilibrium, thermodynamic, and kinetic studies for the biosorption of Basic red 46 onto the sawdust biomass were performed. In addition, a single-stage batch dye biosorption system was also designed. The dye biosorption yield of biosorbent was significantly influenced by the change of operating variables. The experimental data were best described by the Freundlich isotherm model and both the pseudo-first-order kinetic and the pseudo-second-order kinetic models. Thermodynamic research indicated that the biosorption of dye was feasible and spontaneous. Based on the Langmuir isotherm model, the biosorbent was found to have a maximum biosorption potential higher than many other biosorbents in the literature (264.915?mg g^?1). Thus, this investigation presents a novel green option for the assessment of waste sawdust biomass as a cheap and effective biosorbent material.     

Kinetic and equilibrium studies of copper biosorption onto <Emphasis Type="Italic">Pseudomonas aeruginosa</Emphasis> base using direct determination of copper by a voltammetric method

This paper provided information on the use of linear sweep anodic stripping voltammetry for evaluating the process of copper biosorption onto Pseudomonas aeruginosa. This technique was suited to determine the concentration of free copper ion on site on the mercaptoethane sulfonate modified gold electrode surface without any pretreatment. It was in favor of the study of kinetic process as the fast changing kinetic data characteristic just after the beginning of biosorption could be accurately depicted. Based on the electrochemical results, the kinetics and equilibrium of biosorption were systematically examined. The pseudo-second-order kinetic model was used to correlate the kinetic experimental data and the kinetic parameters were evaluated. The Langmuir and Freundlich models were applied to describe the biosorption equilibrium. It was found that the Langmuir isotherm fitted the experimental data better than the Freundlich isotherm. Maximum adsorption capacity of copper ion onto Pseudomonas aeruginosa was 0.9355 μmol mg⁻¹ (about 59.4417 mg g⁻¹).     

Application of Arthrospira (Spirulina) platensis biomass for silver removal from aqueous solutions

The cyanobacterium Arthrospira (Spirulina) platensis was used to study the process of silver biosorption. Effects of various parameters such as contact time, dosage of biosorbent, initial pH, temperature, and initial concentration of Ag(I) were investigated for a batch adsorption system. The optimal biosorption conditions were determined as pH 5.0, biosorbent dosage of 0.4 g, and initial silver concentration of 30 mg/L. Equilibrium adsorption data were analyzed by the Langmuir and Freundlich models – however, the Freundlich model provided a better fit to the experimental data. The kinetic data fit the pseudo-second-order model well, with a correlation coefficient of 0.99. The analysis of thermodynamic parameters (ΔG°, ΔH° and ΔS°) revealed that the adsorption process of silver ion by spirulina biomass was exothermic and spontaneous (ΔG° < 0), and exothermic (ΔH° < 0) process. The biosorption capacity of biomass A. platensis serves as a basis for the development of green technology for environmental remediation.     

Immobilization of blue green microalgae on loofa sponge to biosorb cadmium in repeated shake flask batch and continuous flow fixed bed column reactor system

Summary An indigenous strain of blue green microalga, Synechococcus sp., isolated from wastewater, was immobilized onto loofa sponge discs and investigated as a potential biosorbent for the removal of cadmium from aqueous solutions. Immobilization has enhanced the sorption of cadmium and an increase of biosorption (21%) at equilibrium was noted as compared to free biomass. The kinetics of cadmium biosorption was extremely rapid, with (96%) of adsorption within the first 5 min and equilibrium reached at 15 min. Increasing initial pH or initial cadmium concentration resulted in an increase in cadmium uptake. The maximum biosorption capacity of free and loofa immobilized biomass of Synechococcus sp. was found to be 47.73 and 57.76 mg g⁻¹ biomass respectively. The biosorption equilibrium was well described by Langmuir adsorption isotherm model. The biosorbed cadmium was desorbed by washing the immobilized biomass with dilute HCl (0.1 M) and desorbed biomass was reused in five biosorption–desorption cycles without an apparent decrease in its metal biosorption capacity. The metal removing capacity of loofa immobilized biomass was also tested in a continuous flow fixed-bed column bioreactor and was found to be highly effective in removing cadmium from aqueous solution. The results suggested that the loofa sponge-immobilized biomass of Synechococcus sp. could be used as a biosorbent for an efficient removal of heavy metal ions from aqueous solution.     

Fish (Labeo rohita) Scales as Potential Low-Cost Biosorbent for Removal of Malachite Green from Aqueous Solutions

The feasibility of using fish (Labeo rohita) scales as low-cost biosorbent for the removal of hazardous Malachite Green (MG) dye from aqueous solutions was investigated. Employing a batch experimental setup, the effect of operational parameters such as biosorbent dose, initial solution pH, contact time, and temperature on the dye removal process was studied. The equilibrium biosorption data followed both Langmuir and Freundlich isotherm models, whereas the experimental kinetic data fitted well to the pseudo-second-order kinetic model. Thermodynamic study indicated spontaneous and endothermic nature of the biosorption process. The results suggest that fish scales could be used as an effective biosorbent for removal of MG dye from aqueous solutions.     

Characterization and lead(II) ions removal of modified Punica granatum L. peels

The aim of the present study was to enhance the biosorption capacity of a waste biomass of Punica granatum L. peels (PGL) using various chemical modification agents. Among these agents, hexamethylenediamine (HMDA) indicated the best performance with regard to the improvement of lead(II) ions removal from aqueous solution. The characterization of HMDA-modified P. granatum L. peels (HMDA-PGL) was achieved by using elemental analysis, FT-IR, thermogravimetric (TG) analysis and zeta potential measurement techniques. Based on FT-IR study, the chemical modification of P. granatum L. peels take place with its carboxyl, carbonyl, hydroxyl, etc. groups and these groups are responsible for the biosorption of lead(II) ions onto modified biomass. Biosorption equilibrium and kinetic data fitted well the Langmuir isotherm and the pseudo-second-order kinetic models, respectively. The highest biosorption capacity obtained from Langmuir isotherm model was 371.36 mg g^?1. Biosorption process was spontaneous and endothermic in nature according to the thermodynamic results and it quickly reached the equilibrium within 60 minutes. The validity of kinetic models used in this study can be quantitatively tested by using a normalized standard deviation Δq(%).     

Biosorption behavior of heavy metals in bioleaching process of MSWI fly ash by Aspergillus niger

In this study, it was considered that the biosorption of heavy metals by biomass might occur during the bioleaching of fly ash. This work is focused on the biosorption behavior of Al, Fe, Pb and Zn by Aspergillus niger during the bioleaching process. The fungal biomass was contacted with heavy metals solution which extracted from fly ash by using gluconic acid as leaching agent. The equilibrium time for biosorption was about 120 min. The biosorption experiment data at initial pH 6.5 was used to fit the biosorption kinetics and isotherm models. The results indicated that the biosorption of Al, Fe and Zn by A. niger biomass were well described by the pseudo-first order kinetic model. The pseudo-second order kinetic model was more suitable for that of Pb. The Langmuir isotherm model could well describe the biosorption of Fe, Pb and Zn while the Freundlich model could well describe the biosorption of Al. Furthermore, the biosorption of metal ions decreased evidently in the presence of fly ash as compared to that in the absence of fly ash. This research showed that although the biomass sorption occurred during the bioleaching process, it did not inhibit the removal of Al, Fe, Pb and Zn evidently from fly ash.     

Adsorption Optimization of Lead (II) Using Saccharum Bengalense as a Non-Conventional Low Cost Biosorbent: Isotherm and Thermodynamics Modeling

In the present study a novel biomass, derived from the pulp of Saccharum bengalense, was used as an adsorbent material for the removal of Pb (II) ions from aqueous solution. After 50 minutes contact time, almost 92% lead removal was possible at pH 6.0 under batch test conditions. The experimental data was analyzed using Langmuir, Freundlich, Timken and Dubinin-Radushkevich two parameters isotherm model, three parameters Redlich—Peterson, Sip and Toth models and four parameters Fritz Schlunder isotherm models. Langmuir, Redlich—Peterson and Fritz-Schlunder models were found to be the best fit models. Kinetic studies revealed that the sorption process was well explained with pseudo second-order kinetic model. Thermodynamic parameters including free energy change (ΔG°), enthalpy change (ΔH°) and entropy change (ΔS°) have been calculated and reveal the spontaneous, endothermic and feasible nature of the adsorption process. The thermodynamic parameters of activation (ΔG ^#, ΔH ^#and ΔS ^#) were calculated from the pseudo-second order rate constant by using the Eyring equation. Results showed that Pb (II) adsorption onto SB is an associated mechanism and the reorientation step is entropy controlled.     

Biosorption of cadmium (II) ions by immobilized cells of Pycnoporus sanguineus from aqueous solution

Biosorption of cadmium (II) ions from aqueous solution onto immobilized cells of Pycnoporus sanguineus (P. sanguineus) was investigated in a batch system. Equilibrium and kinetic studies were conducted by considering the effect of pH, initial cadmium (II) concentration, biomass loading and temperature. Results showed that the uptake of cadmium (II) ions increased with the increase of initial cadmium (II) concentration, pH and temperature. Langmuir, Freundlich and Redlich-Peterson isotherm models were used to analyze the equilibrium data at different temperatures. Langmuir isotherm model described the experimental data well followed by Redlich-Peterson and Freundlich isotherm models. Biosorption kinetics data were fitted using pseudo-first, pseudo-second-order and intraparticle diffusion. It was found that the kinetics data fitted well the pseudo-second-order followed by intraparticle diffusion. Thermodynamic parameters such as standard Gibbs free energy (Delta G0), standard enthalpy (Delta H0) and standard entropy (Delta S0) were evaluated. The result showed that biosorption of cadmium (II) ions onto immobilized cells of P. sanguineus was spontaneous and endothermic nature.     

Performance of durian shell waste as high capacity biosorbent for Cr(VI) removal from synthetic wastewater

The capability of durian shell waste biomass as a novel and potential biosorbent for Cr(VI) removal from synthetic wastewater was studied. The adsorption study was performed in batch mode at different temperatures and pH. Langmuir and Freundlich isotherm models fit the equilibrium data very well (R² > 0.99). The maximum biosorption capacity of durian shell was 117 mg/g. On modeling its kinetic experimental data, the pseudo-first order prevails over the pseudo-second order model. Thermodynamically, the characteristic of Cr-biosorption process onto durian shell surface was spontaneous, irreversible and endothermic.     

Removal of Chromium(VI) Ions from Synthetic Solutions by the Fungus Penicillium purpurogenum

The ability of Penicillium purpurogenum to bind high amounts of chromium(VI) from aqueous solutions is demonstrated. Cr(VI) adsorption capacity increases with time during the first four hours and then leveled off toward the equilibrium adsorption capacity. Biosorption of Cr(VI) ions reached equilibrium in four hours. Binding of Cr(VI) ions with Penicillium purpurogenum biomass was clearly pH dependent. Cr(VI) loading capacity increased with increasing pH. The adsorption of Cr(VI) ions reached a plateau value at a pH of approx. 6.0. The maximum capacity of adsorption of Cr(VI) ions onto the fungal biomass was 36.5 mg/g. Adsorption behavior of Cr(VI) ions can be approximately described with the Langmuir equation. When applying the Langmuir model, the maximum adsorption capacity (Q_max) and the Langmuir constant were found to be 40 mg/g and 3.9 × 10^–3 mg/L. Elution of Cr(VI) ions was performed by means of 0.5 M HCl. It was possible to use the biomass of Penicillium purpurogenum for six cycles for biosorption.     

Biosorption of three textile dyes from contaminated water by filamentous green algal Spirogyra sp.: Kinetic,isotherm and thermodynamic studies

A freshwater filamentous green alga Spirogyra sp. was used as an inexpensive and efficient biosorbent for the removal of C.I. Acid Orange 7 (AO7), C.I. Basic Red 46 (BR46) and C.I. Basic Blue 3 (BB3) dyes from contaminated water. The effects of various physico–chemical parameters on dye removal efficiency were investigated, e.g. contact time, pH, initial dyes concentration, the amount of alga, temperature and biosorbent particle size. Dyes biosorption was a quick process and reactions reached to equilibrium conditions within 60 min. The biosorption capacity of three dyes onto alga was found in the following order: BR46 > BB3> AO7. The values of thermodynamic parameters, including ΔG, ΔH and ΔS, indicated that the biosorption of the dyes on the dried Spirogyra sp. biomass was feasible, spontaneous and endothermic. The pseudo-first order, pseudo-second order and the intraparticle diffusion models were applied to the experimental data in order to kinetically describe the removal mechanism of dyes, with the second one showing the best fit with the experimental kinetic biosorption data (R² = 0.99). It was also found that the adsorption process followed the Freundlich isotherm model with the highest value of correlation coefficients (0.99) and the biosorption capacity being estimated to be 13.2, 12.2 and 6.2 mg g⁻¹ for BR46, BB3 and AO7, respectively.     

Enhancement of Lead(II) Biosorption by Microalgal Biomass Immobilized onto Loofa (Luffa cylindrica) Sponge

A unicellular green microalga, Chlorella sorokiniana, was immobilized on loofa (Luffa cylindrica) sponge and successfully used as a new biosorption system for the removal of lead(II) ions from aqueous solutions. The biosorption of lead(II) ions on both free and immobilized biomass of C. sorokiniana was investigated using aqueous solutions in the concentration range of 10–300 mg/L. The biosorption of lead(II) ions by C. sorokiniana biomass increased as the initial concentration of lead(II) ions increased in the medium. The maximum biosorption capacity for free and immobilized biomass of C. sorokiniana was found to be 108.04 and 123.67 mg lead(II)/g biomass, respectively. The biosorption kinetics were found to be fast, with 96 % of adsorption within the first 5 min and equilibrium reached at 15 min. The adsorption of lead(II) both by free and immobilized C. sorokiniana biomass followed the Langmuir isotherm. The biosorption capacities were detected to be dependent on the pH of the solution; and the maximum adsorption was obtained at a solution pH of about 5. The effect of light metal ions on lead(II) uptake was also studied and it was shown that the presence of light metal ions did not significantly affect lead(II) uptake. The loofa sponge‐immobilized C. sorokiniana biomass could be regenerated using 0.1 M HCl, with up to 99 % recovery. The desorbed biomass was used in five biosorption‐desorption cycles, and no noticeable loss in the biosorption capacity was observed. In addition, fixed bed breakthrough curves for lead(II) removal were presented. These studies demonstrated that loofa sponge‐immobilized biomass of C. sorokiniana could be used as an efficient biosorbent for the treatment of lead(II) containing wastewater.     

The Suitability of Jatropha Seed Press Cake as a Biosorbent for Removal of Hexavalent Chromium from Aqueous Solutions

Jatropha seed press cake (JPC), a biodeisel waste, was investigated for its use as biosorbent for Cr(VI) removal from wastewater. The acid-pretreated biomass exhibited 1.9-fold higher biosorption efficiency for Cr(VI). The Cr(VI) biosorption efficiency was found to increase with decrease in pH of aqueous medium. The adsorption capacity of biosorbent for Cr(VI) increased with increasing concentration of Cr(VI). The biosorption of Cr(VI) by acid-treated JPC followed a pseudo-second-order kinetics. The results of equilibrium studies showed that the biosorption process fitted the Langmuir isotherm model, with a maximum adsorption capacity of 22.727 mg of Cr(VI)/g of biosorbent at 30°C. The activation energy was found to be 27.114 kJ/mol, suggesting that the adsorption process was mainly a physical process. The important thermodynamic parameters of adsorption (ΔG, ΔH, andΔS) were determined, which indicated that the Cr(VI) sorption by JPC is a spontaneous and endothermic process.     

Comparison of Rhizopus nigricans in a pelleted growth form with some other types of waste microbial biomass as biosorbents for metal ions

Biosorption of metal ions (Li⁺, Ag⁺, Pb²⁺, Cd²⁺, Ni²⁺, Zn²⁺, Cu²⁺, Sr²⁺, Fe²⁺, Fe³⁺ and Al³⁺) by Rhizopus nigricans biomass was studied. It was shown that metal uptake is a rapid and pH-dependent process, which ameliorates with increasing initial pH and metal concentrations. Different adsorption models: Langmuir, Freundlich, split-Langmuir and combined nonspecific-Langmuir adsorption isotherm were applied to correlate the equilibrium data. The maximum biosorption capacities for the individual metal ions were in the range from 160 to 460 mol/g dry weight. Scatchard transformation of equilibrium data revealed diverse natures of biomass metal-binding sites. The binding of metals was also discussed in terms of the hard and soft acids and bases principle. The maximum biosorption capacities and the binding constant of R. nigricans were positively correlated with the covalent index of metal ions.The following types of waste microbial biomass originating as by-products from industrial bioprocesses were tested for biosorption of metal ions: Aspergillus terreus, Saccharomyces cerevisiae, Phanerochaete chrysosporium, Micromonospora purpurea, M. inyoensis and Streptomyces clavuligerus. The determined maximum biosorption capacities were in the range from 100 to 500 mol/g dry weight. The biosorption equilibrium was also represented with Langmuir and Freundlich sorption isotherms.