显微CT分辨率对松质骨微观结构及生物力学测量的影响

目的:探究不同分辨率对显微CT测量腰椎松质骨显微结构及显微有限元分析松质骨生物力学参数精确性的影响。方法:以人腰椎L5椎体标本为对象,通过显微CT扫描得到松质骨显微CT数据,扫描分辨率为14μm,通过对合并像素点将分辨率降低至28μm~224μm等,分别测量不同分辨率下,松质骨标本的结构参数;利用不同分辨率下的显微CT数据建立显微有限元模型,计算各正交异性的弹性模量,应用统计学分析比较结构参数和力学参数的在不同分辨率下的差异。结果:各参数与分辨率间相关性不尽相同,BV/TV(骨体积分数)和Tb.Th(平均骨小梁厚度)的数值大小随着分辨率的降低呈增高趋势,Conn.D(骨小梁连接度),BS/BV(骨表面积体积比),Tb.N(平均骨小梁密度)和Tb.Sp(平均骨小梁间距)随着分辨率的降低呈降低趋势。分辨率的改变对SMI(结构模型指数)和DA(骨小梁各向异性度)没有显著影响。在三个轴向上,弹性模量均随着分辨率的降低呈增高趋势,当分辨率大于126μm时,该分辨率下的弹性模量和对照组存在显著性差异(P<0.05)。结论:该实验证实了不同分辨率对显微CT测量腰椎松质骨显微结构和生物力学参数有显著影响。提示在研究腰椎松质骨显微结构和生物力学参数时,采用126μm以上分辨率,可以在不降低准确度的情况下提高运算效率。     

去卵巢大鼠腰椎骨微结构变化的动态观察

目的:动态观察去卵巢大鼠腰椎骨微结构的变化。方法:将90只3月龄雌性SD大鼠按体重进行分层随机抽样分组,分为基础组(10只)、假手术组(40只)和去卵巢组(40只)。手术前(0周)处死基础组大鼠,手术后3、6、12、24周时,分批处死假手术和去卵巢组大鼠各8-10只。从每组随机取6只大鼠的第5腰椎行micro-CT扫描及三维结构重建,选取椎体1 mm处,2.0 mm×3.5mm,厚0.9 mm的骨组织为感兴趣区域(interesting area),进行骨形态计量学分析。结果:与同一时间点假手术组大鼠比较,去卵巢3周时,第5腰椎体积骨密度(v BMD)、骨体积分数(BV/TV)、骨小梁数目(Tb.N)、骨小梁厚度(Tb.Th)、骨小梁间隙(Tb.Sp)和结构模型指数(SMI)均无显著变化;去卵巢6周时,Tb.Th显著下降(P0.05),而其他指标均无显著变化;从去卵巢12周到24周时,不仅Tb.Th显著下降(P0.05),而且v BMD、BV/TV和Tb.N也显著下降(P0.05),同时Tb.Sp和SMI显著增加(P0.05)。结论:3月龄大鼠在去卵巢后的6周时骨小梁厚度变薄,12周以后,体积骨密度和骨体积分数下降,骨小梁数目减少。     

人体颈椎松质骨显微结构和力学性能的区域性差异研究

目的:探讨人体脊柱松质骨骨骼显微结构和力学性能的区域性差异,为松质骨三维结构采样部位的选取提供参考。方法:显微CT扫描6块颈6椎体标本获得三维图像,依据椎体内解剖位置的不同,将松质骨划分为6个位置组:外侧、内侧、腹侧、背侧、头侧和尾侧。利用显微结构参数骨体积分数(Bone volume to tissue volume,BV/TV)、骨表面积和骨体积的比值(Bone surface to bone volume,BS/BV)、骨小梁数量(Trabecular number,Tb.N)、骨小梁厚度(Trabecular thickness,Tb.Th)、骨小梁分离度(Trabecular separation,Tb.Sp)和个体化骨小梁分割方法(Individual trabeculae segmentation,ITS)分析6个位置组内松质骨显微结构,并利用有限元分析,获得6个位置组内松质骨的力学性能参数表观弹性模量和表观剪切模量。分别两两对比外侧和内侧,腹侧和背侧,头侧和尾侧松质骨的显微结构参数(BV/TV、BS/BV、Tb.N、Tb.Th、Tb.Sp和个体化骨小梁分割得到的参数)和力学性能参数(表观弹性模量和表观剪切模量)。结果:头侧和尾侧的主要显微结构参数BV/TV、Tb.Th、Tb.N等和表观弹性模量均存在显著差异(P0.05)。腹侧和背侧、内侧和外侧的主要显微结构参数BV/TV、Tb.Th、Tb.N等无显著差异。外侧和内侧的表观弹性模量在非主方向即内外方向和腹背放上上存在显著差异(P0.05),在主方向即头尾上无显著差异。结论:在实验中采集椎体松质骨样本以及临床上利用高分辨率CT分析椎体松质骨结构时,感兴趣区域要同时涵盖头侧和尾侧。     

生物活性玻璃提高骨质疏松绵羊椎弓根螺钉稳定性的体内实验研究

目的:研究生物活性玻璃(Bioactive Glass,BG)在骨质疏松绵羊体内强化椎弓根螺钉固定的力学效果,并观察钉道界面及材料吸收等情况。方法:4只成年雌性小尾寒羊,采用去势联合激素注射方法建立骨质疏松绵羊模型。选择绵羊L2至L5双侧椎弓根,随机化选取一侧直接拧入椎弓根螺钉(空白组),对侧采用BG强化钉道后拧入椎弓根螺钉(实验组)。术后3月随机选取6个椎体(12枚椎弓根螺钉),对螺钉骨质界面行显微CT分析和组织学观察。对剩余10个椎体(20枚椎弓根螺钉)行轴向拔出实验,分析螺钉固定强度。结果:术前绵羊腰椎BMD为0.818±0.0310 g/cm2,建模完成后为1.000±0.0316 g/cm2,BMD平均值下降22.38%,差异有统计学意义(P<0.05)。实验组螺钉骨质界面的Tb.Th、Tb.N组较对照组分别增加143.60%和33.56%,差异有统计学意义(P<0.05)。实验组钉道周围材料绝大部分已经降解吸收,大量新生骨组织紧密包裹螺钉;对照组钉道周围骨量较少,钉骨结合不紧密,实验组螺钉骨质界面结合优于对照组。实验组的最大轴向拔出力为1083.04±86.37N,空白组为871.76±79.03N,前者较后者提高25.26%,差异有统计学意义(P<0.05)。结论:生物活性玻璃能显著改善骨质疏松情况下螺钉骨质界面的骨微观结构,进而提高椎弓根螺钉的把持力。     

新型可降解锌合金内固定系统用于犬下颌骨骨折固定的研究

目的:探讨新型可降解锌合金内固定系统用于犬下颌骨骨折固定的可行性。方法:选择比格犬12只,并将其随机分为两组,其中6只为锌合金实验组,6只为钛合金对照组。每只比格犬的下颌作左右两个骨折内固定模型,每侧骨折模型使用一套小型四孔直连内固定产品。分别于术后即刻、术后4周、12周拍X片。于术前、术后4周、12周、24周抽血检测微量元素锌。于术后12周、24周分批次将动物安乐死,取下颌骨块行Micro-CT检测,取动物重要脏器和内固定周围软组织做病理切片。结果:全程动物无脱落,实验组与对照组骨折均临床愈合。X线图像及Micro-CT显示实验组与对照组的内固定效果比较差异无统计学意义(P0.05)。锌合金表面有明显的降解产物,Micro-CT测量锌合金的板钉初始体积为155.8±1.536 mm~3,12周体积为147.1±0.9893 mm~3,24周体积为137±5.365 mm~3,降解率12.07%,随着植入后时间的延长显著下降(P0.05),而钛合金板钉体积无显著变化。实验组及对照组心、肝、肾及植入物板周软组织均未见异常。血清锌离子浓度在正常范围内略有上升,各时间节点比较差异无统计学意义(P0.05)。结论:可降解锌合金内固定系统可以对犬下颌骨骨折提供稳固的固定,可降解锌合金在下颌骨部位具有一定的降解性能,血液中锌离子未见明显异常升高,对心、肝、肾及植入物周围软组织无毒性作用。     

PRP 与CPC 应用于拔牙后种植位点保存的实验研究

目的:探讨磷酸钙骨水泥(CPC)与富血小板血浆(PRP)混合物应用于拔牙后种植位点保存的可行性。方法:拔除6只犬下颌双侧第三切牙与一侧第一切牙,并于每只犬的3个拔牙窝颊舌侧骨壁分别制造2 mm×2 mm×3 mm缺损,随机在两个牙槽窝内分别植入CPC或CPC与PRP的混合物,第三个不加处置作对照,在术后4、8、12周各处死两只动物,行大体、X线、显微镜观察,比较各组的新骨生成情况。结果:术后4周时CPC/PRP混合物组骨形成早于其他组,8、12周时CPC/PRP混合物组新骨生成明显优于CPC组和对照组。结论:CPC混合PRP可促牙槽窝新骨生成并能保证成骨的高度和颊舌向宽度,从而为后期种植义齿修复提供了必要的条件。     

生物活性玻璃提高骨质疏松绵羊椎弓根螺钉稳定性的体内实验研究

目的：研究生物活性玻璃（Bioactive Glass,BG）在骨质疏松绵羊体内强化椎弓根螺钉固定的力学效果,并观察钉道界面及材料吸收等情况。方法：4只成年雌性小尾寒羊,采用去势联合激素注射方法建立骨质疏松绵羊模型。选择绵羊L2至L5双侧椎弓根,随机化选取一侧直接拧入椎弓根螺钉（空白组）,对侧采用BG强化钉道后拧入椎弓根螺钉（实验组）。术后3月随机选取6个椎体（12枚椎弓根螺钉）,对螺钉骨质界面行显微CT分析和组织学观察。对剩余10个椎体（20枚椎弓根螺钉）行轴向拔出实验,分析螺钉固定强度。结果：术前绵羊腰椎BMD为0.818±0.0310 g/cm2,建模完成后为1.000±0.0316 g/cm2,BMD平均值下降22.38%,差异有统计学意义（P〈0.05）。实验组螺钉骨质界面的Tb.Th、Tb.N组较对照组分别增加143.60%和33.56%,差异有统计学意义（P〈0.05）。实验组钉道周围材料绝大部分已经降解吸收,大量新生骨组织紧密包裹螺钉;对照组钉道周围骨量较少,钉骨结合不紧密,实验组螺钉骨质界面结合优于对照组。实验组的最大轴向拔出力为1083.04±86.37N,空白组为871.76±79.03N,前者较后者提高25.26%,差异有统计学意义（P〈0.05）。结论：生物活性玻璃能显著改善骨质疏松情况下螺钉骨质界面的骨微观结构,进而提高椎弓根螺钉的把持力。     

动态观察去卵巢骨质疏松大鼠股骨骨微结构的变化

目的:绝经后骨质疏松是好发于中老年女性人群中的骨代谢疾病,去卵巢骨质疏松大鼠模型是国内外通用的模拟绝经后骨质疏松发生的经典动物模型,本研究通过观察去卵巢骨质疏松大鼠股骨骨微结构的动态变化,为骨质疏松大鼠模型的临床应用提供理论参考依据。方法:将90只3月龄雌性SD大鼠按体重分层后随机分为基础组(10只)、假手术组(40只)和去卵巢组(40只)。分别在手术前(基础组)和后的3、6、12、24周,腹主动脉取血处死基础组以及假手术组和去卵巢组大鼠,每组各8-10只。每组中随机取6只大鼠,对其左股骨行micro-CT扫描及三维结构重建。选择股骨远端距生长板远端1 mm处,2.0 mm×3.5 mm,厚0.9 mm的骨组织为感兴趣区域,对感兴趣区域进行骨形态计量学分析。结果:与0周组比较,从去卵巢3周开始一直持续到24周,去卵巢组大鼠股骨vBMD、BV/TV和Tb.N显著降低,Tb.Sp和SMI显著升高,而Tb.Th无显著变化;与0周组比较,从假手术后3周开始一直到24周,假手术组所有检测指标均无显著变化。与同周龄假手术组比较,从去卵巢3周开始一直持续到24周,去卵巢组大鼠股骨Tb.N、BV/TV和vBMD显著降低,Tb.Sp显著升高,而Tb.Th没有显著变化。从去卵巢6周开始一直到24周,去卵巢组大鼠SMI显著增加。结论:3月龄大鼠股骨远端的骨微结构在去卵巢3周时就出现显著变化。提示,采用3月龄大鼠进行抗骨质疏松药物筛选时,去卵巢3周后就可以进行药物处理。     

应用3D适形打印制备网状复合体对兔颅骨缺损的修复作用及安全性研究

目的:探讨采用3D适形打印技术制备的羟基磷灰石/聚乳酸网状复合体在兔颅骨缺损中的修复作用及安全性。方法:以24只新西兰兔为研究对象,以羟基磷灰石/聚乳酸为材料,采用3D适形打印技术制备网状复合体,于兔颅骨顶部制成两个颅骨全层缺损,分别为孔A(左)和孔B(右),孔A(阳性对照组)以自体颅骨为修复材料,孔B(实验组)以复合体为修复材料,观察缺损修复区域的形态学、影像学(X线及CT扫描)及组织学检查结果。结果:植入后24周时,形态学显示:阳性对照组可见致密的骨组织修复,与缺损边缘界限不清,实验组中支架孔隙内纤维组织由新生骨质取代,且新生骨成熟度较提高,材料表面有部分吸收。CT扫描观察显示:冠状面上,阳性对照组缺损修复区域与周围正常骨组织融合为一体,实验组修复材料与缺损边缘融合紧密,与周围正常骨组织结合良好,部分边缘结合不连贯。组织学观察显示:实验组材料部分降解,材料间隔可见新生骨小梁。研究中无实验动物死亡,皮肤切口处缝合良好,无皮下积液,无移植物脱出、红肿感染等情况出现。结论:以3D适形打印技术制备的羟基磷灰石/聚乳酸复合体对兔颅骨缺损有较好的修复作用,能促进缺损区域新骨的形成和生长,且安全性较高。     

基于聚醚醚酮的骨科植入材料生物相容性研究

本研究基于聚醚醚酮的骨科植入材料生物相容性的研究,进一步分析聚醚醚酮(polyether-ether-ketone,PEEK)骨科植入材料生物的相容性能,以有效提高其生物功能性,进而获得更加可靠的骨-植入体界面。本研究通过以新西兰大白兔为研究对象,采用改性/未改性的PEEK材料制备了腰椎模型并植入,最后进行了生物力学与Micro CT分析。实验研究表明,以改性及未改性的PEEK材料制备的腰椎假体在植入动物体内后后,动物体内未发生显著相关的急慢性毒性反应。对比植入的两种PEEK假体我们发现,改性的PEEK腰椎假体在植入动物后第4周,其临近椎骨的植入部位在骨体积分数等参数上发生了明显的改善(p0.05);植入后第8周检查,以骨体积分数(BV/TV)、(骨密度(BMD)、骨小梁厚度(Tb.Th)、骨小梁分离度(Tb.Sp)以及骨表面体积分数(BS/BV)等为代表的多项重要的骨组织形态计量学参数均发生了显著的改善(p0.05)。同时,研究通过采用拔出试验来验证植入材料的生物力学性能,实验发现改性PEEK材料能够有效促进植入假体与椎骨的紧密结合。因此,实验中针对PEEK材料采用rh BMP-2与胶原蛋白对表面进行改性可以高效地、快速地达到效果,并且能够明显提高骨科植入的PEEK材料的生物功能性与生物相容性。     

Biomechanical and Histological Evaluation of Roughened Surface Titanium Screws Fabricated by Electron Beam Melting

Background

Various fabrication methods are used to improve the stability and osseointegration of screws within the host bone. The aim of this study was to investigate whether roughened surface titanium screws fabricated by electron beam melting can provide better stability and osseointegration as compared with smooth titanium screws in sheep cervical vertebrae.

Methods

Roughened surface titanium screws, fabricated by electron beam melting, and conventional smooth surface titanium screws were implanted into sheep for 6 or 12 weeks (groups A and B, respectively). Bone ingrowth and implant stability were assessed with three-dimensional imaging and reconstruction, as well as histological and biomechanical tests.

Results

No screws in either group showed signs of loosening. Fibrous tissue formation could be seen around the screws at 6 weeks, which was replaced with bone at 12 weeks. Bone volume/total volume, bone surface area/bone volume, and the trabecular number were significantly higher for a define region of interest surrounding the roughened screws than that surrounding the smooth screws at 12 weeks. Indeed, for roughened screws, trabecular number was significantly higher at 12 weeks than at 6 weeks. On mechanical testing, the maximum pullout strength was significantly higher at 12 weeks than at 6 weeks, as expected; however, no significant differences were found between smooth and roughened screws at either time point. The maximum torque to extract the roughened screws was higher than that required for the smooth screws.

Conclusions

Electron beam melting is a simple and effective method for producing a roughened surface on titanium screws. After 12 weeks, roughened titanium screws demonstrated a high degree of osseointegration and increased torsional resistance to extraction over smooth titanium screws.     

Single limb immobilization model for bone loss from unloading

Hindlimb suspension is the most used model for inducing bone loss from unloading but requires a separate ground control group. This control group cannot be used for genetic studies involving outbred mice. In this study, we evaluated a single limb immobilization (SLI) model for inducing bone loss from unloading, with the contralateral limb from the same animal used as a control. Male 10-week old C57Bl/6J mice had one limb immobilized for one, two, or three weeks. Subsequently, an additional group of male 16-week old C57Bl/6J mice had one limb immobilized for three weeks. SLI resulted in decreased tibial trabecular BV/TV, Tb Th, and Tb N compared to contralateral limbs in young mice. Femoral trabecular BV/TV, Tb Th, Tb N, and femoral cortical area fraction were also decreased. Mechanical properties were not affected after three weeks. In adult mice, femoral trabecular BV/TV, Tb Th, and Tb N were decreased. Femoral stiffness, ultimate stress, and Young’s modulus were decreased. Bone properties decreased by SLI were also decreased by hindlimb suspension previously. The results suggest SLI can be an effective model for inducing bone loss in growing and adult mice after three weeks of immobilization.     

种植体稳定系数测定与种植体负重时机选择

目的:通过测量ITI和Osstem-SS种植系统的稳定系数(ISQ),评价这两种种植体的骨结合情况,为临床确定其上部结构修复时机提供依据。方法:93例牙列缺损患者共植入179颗种植体,根据患者种植区骨量情况分为两组,其中A组为种植区骨量良好,不需骨增量手术病例(62例);B组为种植区骨量不足,需进行骨增量手术病例(31例)。A组共植入125颗种植体,其中ITI种植系统64颗,OSSTEM-SS种植系统61颗;B组共植入54颗种植体,其中ITI种植系统28颗,OSSTEM-SS种植系统26颗。术后即刻及第4、6、8、12、16、24周分别测量各时期种植体稳定系数(ISQ),并同期进行临床和影像学检查。结果:A组中ITI种植系统术后8周ISQ值平均(74.17±1.85),进行负重;OSSTEM-SS种植系统术后12周ISQ值平均(72.00±2.59),进行负重。B组中ITI种植系统术后16周ISQ值平均(65.09±3.42),进行负重;OSSTEM-SS种植系统术后24周ISQ值平均(62.09±6.16),进行负重。负重后临床随访3-24个月所有病例均成功,咀嚼功能良好,患者满意。结论:种植体稳定系数(ISQ)能反应种植体骨结合情况,可以协助医生选择种植后合适的冠修复时机。     

A micro-computed tomography study of the trabecular bone structure in the femoral head

The goal of this study was to characterize the trabecular microarchitecture of the femoral head using micro-computed tomography (ICT). Femoral head specimens were obtained from subjects following total hip replacement. Cylindrical cores from the specimens were scanned to obtain 3-D images with an isotropic resolution of 26 Im. Bone structural parameters were evaluated on a per millimeter basis: relative bone volume (BV/TV), trabecular number (Tb.N), thickness (Tb.Th) and separation (Tb.Sp), structure model index (SMI), and connectivity (Conn.D). The ICT data show that the first two millimeters, starting at the joint surface, are characterized by more plate-like trabeculae, and are significantly denser than the underlying trabecular bone. Regional differences in the trabecular architecture reveal that the superior pole has significantly higher BV/TV, Tb.N and Tb.Th values, with lower Tb.Sp compared to the inferior and side poles. Because subchondral bone is essential in the load attenuation of joints, the difference in bone structure between the subchondral and trabecular bone might arise from the different functions each have within joint-forming bones. The denser trabecular structure of the superior pole as compared to the inferior pole can be interpreted as a functional adaptation to higher loading in this area.     

Pulsed Electromagnetic Field Versus Whole Body Vibration on Cartilage and Subchondral Trabecular Bone in Mice With Knee Osteoarthritis

Pulsed electromagnetic field (PEMF) and whole body vibration (WBV) interventions are expected to be important strategies for management of osteoarthritis (OA). The aim of the study was to investigate the comparative effectiveness of PEMF versus WBV on cartilage and subchondral trabecular bone in mice with knee OA (KOA) induced by surgical destabilization of the medial meniscus (DMM). Forty 12-week-old male C57/BL mice were randomly divided into four groups (n = 10): Control, OA, PEMF, and WBV. OA was induced (OA, PEMF, and WBV groups) by surgical DMM of right knee joint. Mice in PEMF group received 1 h/day PEMF exposure with 75 Hz, 1.6 mT for 4 weeks, and the WBV group was exposed to WBV for 20 min/day with 5 Hz, 4 mm, 0.3 g peak acceleration for 4 weeks. Micro-computed tomography (micro-CT), histology, and immunohistochemistry analyses were performed to evaluate the changes in cartilage and microstructure of trabecular bone. The bone volume fraction (BV/TV), trabecular thickness (Tb.Th), and trabecular number (Tb.N) increased, and bone surface/bone volume (BS/BV) decreased by micro-CT analysis in PEMF and WBV groups. The Osteoarthritis Research Society International (OARSI) scores in PEMF and WBV groups were significantly lower than in the OA group. Immunohistochemical results showed that PEMF and WBV promoted expressions of Aggrecan, and inhibited expressions of IL-1β, ADAMTS4, and MMP13. Superior results are seen in PEMF group compared with WBV group. Both PEMF and WBV were effective, could delay cartilage degeneration and preserve subchondral trabecular bone microarchitecture, and PEMF was found to be superior to WBV. Bioelectromagnetics. 2020;41:298–307 © 2020 Bioelectromagnetics Society     

Numerical investigation of bone remodelling around immediately loaded dental implants using sika deer (Cervus nippon) antlers as implant bed

This study combines finite element method and animal studies, aiming to investigate tissue remodelling processes around dental implants inserted into sika deer antler and to develop an alternative animal consuming model for studying bone remodelling around implants. Implants were inserted in the antlers and loaded immediately via a self-developed loading device. After 3, 4, 5 and 6 weeks, implants and surrounding tissue were taken out. Specimens were scanned by μCT scanner and finite element models were generated. Immediate loading and osseointegration conditions were simulated at the implant-tissue interface. A vertical force of 10 N was applied on the implant. During the healing time, density and Young’s modulus of antler tissue around the implant increased significantly. For each time point, the values of displacement, stresses and strains in the osseointegration model were lower than those of the immediate loading model. As the healing time increased, the displacement of implants was reduced. The 3-week immediate loading model (9878 ± 1965 μstrain) illustrated the highest strains in the antler tissue. Antler tissue showed similar biomechanical properties as human bone in investigating the bone remodelling around implants, therefore the use of sika deer antler model is a promising alternative in implant biomechanical studies.     

国产多孔钽材料修复兔胫骨缺损的实验研究

摘要 目的：研究国产多孔钽材料能否在兔胫骨缺损模型中顺利实现骨长入,用于修复胫骨缺损。方法：在36只新西兰大白兔双侧胫骨骨干处建立骨缺损模型,每只动物左右侧缺损随机分组,分别进入实验组(植入多孔坦材料)和对照组（不植入多孔坦材料）。植入后4周、8周和12周取材,通过X线检测以及硬组织切片苏木精伊红染色,检测多孔钽材料与骨界面的骨整合情况。采用推出实验检测多孔钽材料与骨界面的结合强度。结果：将术后不同时间点取得的胫骨标本作X射线拍片分析,4周时,骨缺损端与材料结合部位有骨质生成,在8周时材料表面有骨形成现象,逐渐完全覆盖材料表面,在12周时骨量继续增加,形成覆盖材料并桥接骨缺损断端的骨痂。样本行硬组织切片并行HE染色后检测,植入4周后实验组材料两端被新生骨所覆盖,材料深部的孔隙中也可见少量骨组织长入;植入8周后发现实验组材料与骨组织生长良好,多孔钽材料表面和两端材料孔隙内均有骨组织长入,材料孔隙与组织紧密连接,有骨小梁长入;植入12周时两端骨组织长入深度没有明显变化,但材料表面骨组织继续长入,并完全嵌入圆柱体材料内。材料植入后4周与8周比较差异无统计学意义（P＞0.05）,材料植入后8周与12周比较差异有统计学意义（P<0.05）。将植入4周、8周和12周后含材料样本置于动态疲劳试验机上进行推出实验,随时间延长所需推出力明显增加,植入后4周和8周相比,虽然后者所需推力较大,但两者比较差异无统计学意义（P＞0.05）,而8周和12周比较则差异有统计学意义（P<0.05）。结论：国产多孔坦材料能在胫骨缺损中实现与骨整合,能用于皮质骨缺损修复。