Separator Modified by Cobalt‐Embedded Carbon Nanosheets Enabling Chemisorption and Catalytic Effects of Polysulfides for High‐Energy‐Density Lithium‐Sulfur Batteries

Lithium‐sulfur (Li‐S) batteries are considered to be one of the promising next‐generation energy storage systems. Considerable progress has been achieved in sulfur composite cathodes, but high cycling stability and discharging capacity at the expense of volumetric capacity have offset their advantages. Herein, a functional separator is presented by coating cobalt‐embedded nitrogen‐doped porous carbon nanosheets and graphene on one surface of a commercial polypropylene separator. The coating layer not only suppresses the polysulfide shuttle effect through chemical affinity, but also functions as an electrocatalyst to propel catalytic conversion of intercepted polysulfides. The slurry‐bladed carbon nanotubes/sulfur cathode with 90 wt% sulfur deliver high reversible capacity of 1103 mA h g^?1 and volumetric capacity of 1062 mA h cm^?3 at 0.2 C, and the freestanding carbon nanofibers/sulfur cathode provides a high discharging capacity of 1190 mA h g^?1 and volumetric capacity of 1136 mA h cm^?3 at high sulfur content of 78 wt% and sulfur loading of 10.5 mg cm^?2. The electrochemical performance is comparable with or even superior to those in the state‐of‐the‐art carbon‐based sulfur cathodes. The separator reported in this work holds great promise for the development of high‐energy‐density Li‐S batteries.     

Functionalized Boron Nitride Nanosheets/Graphene Interlayer for Fast and Long‐Life Lithium–Sulfur Batteries

Lithium–sulfur (Li–S) batteries have a much higher energy density than Li ion batteries and thus are considered as next generation batteries for electric vehicle applications. However, the problem of rapid capacity fading due to the shuttling of soluble polysulfides between electrodes remains the main obstacle for practical applications. Here, a thin and selective interlayer structure has been designed and produced to decrease the charge transfer resistance and mitigate the shuttling problem, simply by coating the surface of cathode with a thin film of functionalized boron nitride nanosheets/graphene. Due to this thin and ultralight interlayer, the specific capacity and cycling stability of the Li–S batteries with a cathode of sulfur‐containing porous carbon nanotubes (≈60 wt% sulfur content) have been improved significantly with a life of over 1000 cycles, an initial specific capacity of 1100 mA h g^?1 at 3 C, and a cycle decay as low as 0.0037% per cycle. This new interlayer provides a promising approach to significantly enhance the performance of Li–S batteries.     

3D Hyperbranched Hollow Carbon Nanorod Architectures for High‐Performance Lithium‐Sulfur Batteries

Lithium‐sulfur batteries have been plagued for a long time by low Coulombic efficiency, fast capacity loss, and poor high rate performance. Here, the synthesis of 3D hyperbranched hollow carbon nanorod encapsulated sulfur nanocomposites as cathode materials for lithium‐sulfur batteries is reported. The sulfur nanocomposite cathodes deliver a high specific capacity of 1378 mAh g^‐1 at a 0.1C current rate and exhibit stable cycling performance. The as‐prepared sulfur nanocomposites also achieve excellent high rate capacities and cyclability, such as 990 mAh g^‐1 at 1C, 861 mAh g^‐1 at 5C, and 663 mAh g^‐1 at 10C, extending to more than 500 cycles. The superior electrochemical performance are ascribed to the unique 3D hyperbranched hollow carbon nanorod architectures and high length/radius aspect ratio of the carbon nanorods, which can effectively prevent the dissolution of polysulfides, decrease self‐discharge, and confine the volume expansion on cycling. High capacity, excellent high‐rate performance, and long cycle life render the as‐developed sulfur/carbon nanorod nanocomposites a promising cathode material for lithium‐sulfur batteries.     

Sulfur‐Embedded Activated Multichannel Carbon Nanofiber Composites for Long‐Life,High‐Rate Lithium–Sulfur Batteries

Despite the 3–5 fold higher energy density than the conventional Li‐ion cells at a lower cost, commercialization of Li–S batteries is hindered by the insulating nature of sulfur and the dissolution of intermediate polysulfides (Li₂S _X , 4 < X ≤ 8) into the electrolyte. The authors demonstrate here multichannel carbon nanofibers that are composed of parallel mesoporous channels connected with micropores as sulfur containment. In addition, hydroxyl functional groups are formed on the carbon surface through a chemical activation to enhance the interaction between sulfur and carbon. In the sulfur embedded composite, the mesoporous multichannel enhances the active material utilization and sulfur loading, while the micropores act as a reaction chamber for sulfur component and trap site for polysulfide with the assistance of the functional groups. This sulfur–carbon composite electrode with 2.2 mg cm^?2 sulfur displays excellent performance with high rate capability (initial capacity of 1351 mA h g^?1 at C/5 rate and 847 mA h g^?1 at 5C rate), maintaining 920 mA h g^?1 even after 300 cycles (a decay of 0.07% per cycle). Furthermore, a stable reversible capacity of as high as ≈1100 mA h g^?1 is realized with a higher sulfur loading of 4.6 mg cm^?2.     

Dense Graphene Monolith for High Volumetric Energy Density Li–S Batteries

Despite the outstanding gravimetric performance of lithium–sulfur (Li–S) batteries, their practical volumetric energy density is normally lower than that of lithium‐ion batteries, mainly due to the low density of nanostructured sulfur as well as the porous carbon hosts. Here, a novel approach is developed to fabricate high‐density graphene bulk materials with “ink‐bottle‐like” mesopores by phosphoric acid (H₃PO₄) activation. These pores can effectively confine the polysulfides due to their unique structure with a wide body and narrow neck, which shows only a 0.05% capacity fade per cycle for 500 cycles (75% capacity retention) for accommodating polysulfides. With a density of 1.16 g cm^?3, a hybrid cathode containing 54 wt% sulfur delivers a high volumetric capacity of 653 mA h cm^?3. As a result, a device‐level volumetric energy density as high as 408 W h L^?1 is achieved with a cathode thickness of 100 µm. This is a periodic yet practical advance to improve the volumetric performance of Li–S batteries from a device perspective. This work suggests a design principle for the real use Li–S batteries although there is a long way ahead to bridge the gap between Li–S batteries and Li–ion batteries in volumetric performance.     

3D Printing Sulfur Copolymer‐Graphene Architectures for Li‐S Batteries

3D printing is becoming an efficient approach to facilely and accurately fabricate diverse complex architectures with broad applications. However, suitable inks and 3D print favorable architectures with high electrochemical performances for energy storage are still being explored. Here, sulfur copolymer‐graphene architectures with well‐designed periodic microlattices are 3D printed as a cathode for Li‐S batteries using a suitable ink composed of sulfur particles, 1,3‐diisopropenylbenzene (DIB), and condensed graphene oxide dispersion. Using thermal treatment, elemental sulfur can be reacted with DIB to produce sulfur copolymer, which can partially suppress the dissolution of polysulfides. Moreover, graphene in the architecture can provide high electrical conductivity for whole electrode. Hence, 3D printed sulfur copolymer‐graphene architecture exhibits a high reversible capacity of 812.8 mA h g^?1 and good cycle performance. Such a simple 3D printing approach can be further extended to construct many complex architectures for various energy storage devices.     

Fabrication of N‐doped Graphene–Carbon Nanotube Hybrids from Prussian Blue for Lithium–Sulfur Batteries

Hybrid nanostructures containing 1D carbon nanotubes and 2D graphene sheets have many promising applications due to their unique physical and chemical properties. In this study, the authors find Prussian blue (dehydrated sodium ferrocyanide) can be converted to N‐doped graphene–carbon nanotube hybrid materials through a simple one‐step pyrolysis process. Through field emission scanning electron microscopy, transmission electron microscopy, X‐ray diffraction, Raman spectra, atomic force microscopy, and isothermal analyses, the authors identify that 2D graphene and 1D carbon nanotubes are bonded seamlessly during the growth stage. When used as the sulfur scaffold for lithium–sulfur batteries, it demonstrates outstanding electrochemical performance, including a high reversible capacity (1221 mA h g^?1 at 0.2 C rate), excellent rate capability (458 and 220 mA h g^?1 at 5 and 10 C rates, respectively), and excellent cycling stability (321 and 164 mA h g^?1 at 5 and 10 C (1 C = 1673 mA g^?1) after 1000 cycles). The enhancement of electrochemical performance can be attributed to the 3D architecture of the hybrid material, in which, additionally, the nitrogen doping generates defects and active sites for improved interfacial adsorption. Furthermore, the nitrogen doping enables the effective trapping of lithium polysulfides on electroactive sites within the cathode, leading to a much‐improved cycling performance. Therefore, the hybrid material functions as a redox shuttle to catenate and bind polysulfides, and convert them to insoluble lithium sulfide during reduction. The strategy reported in this paper could open a new avenue for low cost synthesis of N‐doped graphene–carbon nanotube hybrid materials for high performance lithium–sulfur batteries.     

Microemulsion Assisted Assembly of 3D Porous S/Graphene@g‐C3N4 Hybrid Sponge as Free‐Standing Cathodes for High Energy Density Li–S Batteries

A 3D porous sulfur/graphene@g‐C₃N₄ (S/GCN) hybrid sponge, which can be directly applied as a free‐standing cathode for Li–S batteries, is realized via a microemulsion assisted assembly approach. In this strategy, the interior oil emulsion droplets serve as soft templates to form pores to accommodate sulfur and the hydrophilic GCN stacks around oil droplets to assemble into a crosslinked 3D network. Through this microemulsion encapsulation route, S/GCN cathodes with a sulfur loading as high as 82 wt% can be achieved. Furthermore, the enriched N‐sites in GCN macropores offer numerous adhesion sites for polysulfides, realizing a “physical‐chemical” dual‐confinement for polysulfides from diffusion. Moreover, the robust and highly porous 3D graphene frameworks render efficient electron/Li⁺ transport pathways for fast kinetics as well as good structure integrity. Consequently, in comparison to the conventional G‐sponge/Li₂S_n catholyte system, S/GCN delivers a higher specific capacity, superior high‐rate capability (612 mA h g^?1 at 10 C), and alleviated anode corrosion issues. Particularly, an energy density as high as 1493 W h kg^?1 (calculated on the total weight of the cathode) and an extremely low capacity fading rate of 0.017% per cycle over 800 cycles at 0.3 C are achieved.     

High‐Performance All‐Solid‐State Lithium–Sulfur Batteries Enabled by Amorphous Sulfur‐Coated Reduced Graphene Oxide Cathodes

Safety and the polysulfide shuttle reaction are two major challenges for liquid electrolyte lithium–sulfur (Li–S) batteries. Although use of solid‐state electrolytes can overcome these two challenges, it also brings new challenges by increasing the interface resistance and stress/strain. In this work, the interface resistance and stress/strain of sulfur cathodes are significantly reduced by conformal coating ≈2 nm sulfur (S) onto reduced graphene oxide (rGO). An Li–S full cell consisting of an rGO@S‐Li₁₀GeP₂S₁₂‐acetylene black (AB) composite cathode is evaluated. At 60 °C, the all‐solid‐state Li–S cell demonstrates a similar electrochemical performance as in liquid organic electrolyte, with high rate capacities of 1525.6, 1384.5, 1336.3, 903.2, 502.6, and 204.7 mA h g^?1 at 0.05, 0.1, 0.5, 1.0, 2.0, and 5.0 C, respectively. It can maintain a high and reversible capacity of 830 mA h g^?1 at 1.0 C for 750 cycles. The uniform distribution of the rGO@S nanocomposite in the Li₁₀GeP₂S₁₂‐AB matrix generates uniform volume changes during lithiation/delithiation, significantly reducing the stress/strain, thus extending the cycle life. Minimization of the stress/strain of solid cells is the key for a long cycle life of all‐solid‐state Li–S batteries.     

Synergetic Protective Effect of the Ultralight MWCNTs/NCQDs Modified Separator for Highly Stable Lithium–Sulfur Batteries

Lithium–sulfur (Li–S) batteries are highly attractive due to their high energy density, potentially low cost, and environmental compatibility. However, their commercialization has been greatly hindered by their poor cycle life and severe self‐discharge, which can be attributed to the polysulfides dissolution. To overcome these issues, much effort has been devoted to engineering the electrode structure and composition to improve the performance which is often expensive and laborious. In this study, an ultralight multiwall carbon nanotube/N‐doped carbon quantum dot (MWCNT/NCQD)‐coated separator is first designed, which is cost effective and facile. The MWCNTs/NCQDs‐coated separator is then applied in Li–S batteries. The MWCNTs/NCQDs coating provides a physical shield against polysulfide shuttling and chemical adsorption of polysulfides by MWCNTs and NCQDs. The synergetic effect of MWCNTs and NCQDs enables the production of Li–S cell with a relative high initial discharge capacity of 1330.8 mA h g^?1 and excellent cyclic performance with a corresponding capacity fade rate of as low as 0.05% per cycle at 0.5 C over 1000 cycles. Excellent rate capability and anti‐self‐discharge behavior are also displayed. The design of MWCNTs/NCQDs‐coated separator is a viable approach for successfully developing practical Li–S batteries.     

Elastic Sandwich‐Type rGO–VS2/S Composites with High Tap Density: Structural and Chemical Cooperativity Enabling Lithium–Sulfur Batteries with High Energy Density

Driven by increasing demand for high‐energy‐density batteries for consumer electronics and electric vehicles, substantial progress is achieved in the development of long‐life lithium–sulfur (Li–S) batteries. Less attention is given to Li–S batteries with high volume energy density, which is crucial for applications in compact space. Here, a series of elastic sandwich‐structured cathode materials consisting of alternating VS₂‐attached reduced graphene oxide (rGO) sheets and active sulfur layers are reported. Due to the high polarity and conductivity of VS₂, a small amount of VS₂ can suppress the shuttle effect of polysulfides and improve the redox kinetics of sulfur species in the whole sulfur layer. Sandwich‐structured rGO–VS₂/S composites exhibit significantly improved electrochemical performance, with high discharge capacities, low polarization, and excellent cycling stability compared with their bare rGO/S counterparts. Impressively, the tap density of rGO–VS₂/S with 89 wt% sulfur loading is 1.84 g cm^?3, which is almost three times higher than that of rGO/S with the same sulfur content (0.63 g cm^?3), and the volumetric specific capacity of the whole cell is as high as 1182.1 mA h cm^?3, comparable with the state‐of‐the‐art reported for energy storage devices, demonstrating the potential for application of these composites in long‐life and high‐energy‐density Li–S batteries.     

Carbon Quantum Dots–Modified Interfacial Interactions and Ion Conductivity for Enhanced High Current Density Performance in Lithium–Sulfur Batteries

Significant progress has achieved for developing lithium–sulfur (Li–S) batteries with high specific capacities and excellent cyclic stability. However, some critical issues emerge when attempts are made to raise the areal sulfur loading and increase the operation current density to meet the standards for various industrial applications. In this work, polyethylenimine‐functionalized carbon dots (PEI‐CDots) are designed and prepared for enhancing performance of the Li–S batteries with high sulfur loadings and operation under high current density situations. Strong chemical binding effects towards polysulfides and fast ion transport property are achieved in the PEI‐CDots‐modified cathodes. At a high current density of 8 mA cm^?2, the PEI‐CDots‐modified Li–S battery delivers a reversible areal capacity of 3.3 mAh cm^?2 with only 0.07% capacity decay per cycle over 400 cycles at 6.6 mg sulfur loading. Detailed analysis, involving electrochemical impedance spectroscopy, cyclic voltammetry, and density functional theory calculations, is done for the elucidation of the underlying enhancement mechanism by the PEI‐CDots. The strongly localized sulfur species and the promoted Li⁺ ion conductivity at the cathode–electrolyte interface are revealed to enable high‐performance Li–S batteries with high sulfur loading and large operational current.     

An Improved Li–SeS2 Battery with High Energy Density and Long Cycle Life

Selenium–sulfur solid solutions are a class of potential cathode materials for high energy batteries, since they have higher theoretical capacities than selenium and improved conductivity over sulfur. Here, a high‐performance cathode material by confining 70 wt% of SeS₂ in a highly ordered mesoporous carbon (CMK‐3) framework with a polydopamine (PDA) protection sheath for novel Li–Se/S batteries is reported. With a relatively high SeS₂ mass loading of 2.6–3 mg cm^?2, the CMK‐3/SeS₂@PDA cathode exhibits a high capacity of >1200 mA h g^?1 at 0.2 A g^?1, excellent C‐rate capability of 535 mA h g^?1 at 5 A g^?1, and prolonged life over 500 cycles. Benefitting from the unique advantages of SeS₂ and the rationally designed host framework, this new cathode material demonstrates a feasible strategy to overcome the bottlenecks of current Li–S systems for high energy density rechargeable batteries.     

Unraveling the Dual Functionality of High‐Donor‐Number Anion in Lean‐Electrolyte Lithium‐Sulfur Batteries

Minimizing electrolyte use is essential to achieve high practical energy density of lithium–sulfur (Li–S) batteries. However, the sulfur cathode is more readily passivated under a lean electrolyte condition, resulting in low sulfur utilization. In addition, continuous electrolyte decomposition on the Li metal anode aggravates the problem, provoking rapid capacity decay. In this work, the dual functionalities of NO₃^? as a high‐donor‐number (DN) salt anion is presented, which improves the sulfur utilization and cycling stability of lean‐electrolyte Li–S batteries. The NO₃^? anion elevates the solubility of the sulfur species based on its high electron donating ability, achieving a high sulfur utilization of above 1200 mA h g^?1. Furthermore, the anion suppresses electrolyte decomposition on the Li metal by regulating the lithium ion (Li⁺) solvation sheath, enhancing the cycle performance of the lean electrolyte cell. By understanding the anionic effects, this work demonstrates the potential of the high‐DN electrolyte, which is beneficial for both the cathode and anode of Li–S batteries.     

Long‐Life,High‐Rate Lithium–Sulfur Cells with a Carbon‐Free VN Host as an Efficient Polysulfide Adsorbent and Lithium Dendrite Inhibitor

Lithium–sulfur (Li‐S) batteries are a promising next‐generation energy‐storage system, but the polysulfide shuttle and dendritic Li growth seriously hinder their commercial viability. Most of the previous studies have focused on only one of these two issues at a time. To address both the issues simultaneously, presented here is a highly conductive, noncarbon, 3D vanadium nitride (VN) nanowire array as an efficient host for both sulfur cathodes and lithium‐metal anodes. With fast electron and ion transport and high porosity and surface area, VN traps the soluble polysulfides, promotes the redox kinetics of sulfur cathodes, facilitates uniform nucleation/growth of lithium metal, and inhibits lithium dendrite growth at an unprecedented high current density of 10 mA cm^?2 over 200 h of repeated plating/stripping. As a result, VN‐Li||VN‐S full cells constructed with VN as both an anode and cathode host with a negative to positive electrode capacity ratio of only ≈2 deliver remarkable electrochemical performance with a high Coulombic efficiency of ≈99.6% over 850 cycles at a high 4 C rate and a high areal capacity of 4.6 mA h cm^?2. The strategy presented here offers a viable approach to realize high‐energy‐density, safe Li‐metal‐based batteries.     

Highly Dispersed Cobalt Clusters in Nitrogen‐Doped Porous Carbon Enable Multiple Effects for High‐Performance Li–S Battery

The lithium–sulfur (Li–S) battery is considered a promising candidate for the next generation of energy storage system due to its high specific energy density and low cost of raw materials. However, the practical application of Li–S batteries is severely limited by several weaknesses such as the shuttle effect of polysulfides and the insulation of the electrochemical products of sulfur and Li₂S/Li₂S₂. Here, by doping nitrogen and integrating highly dispersed cobalt catalysts, a porous carbon nanocage derived from glucose adsorbed metal–organic framework is developed as the host for a sulfur cathode. This host structure combines the reported positive effects, including high conductivity, high sulfur loading, effective stress release, fast lithium‐ion kinetics, fast interface charge transport, fast redox of Li₂S_n, and strong physical/chemical absorption, achieving a long cycle life (86% of capacity retention at 1C within 500 cycles) and high rate performance (600 mAh g^?1 at 5C) for a Li–S battery. By combining experiments and density functional theoretical calculations, it is demonstrated that the well‐dispersed cobalt clusters play an important role in greatly improving the diffusion dynamics of lithium, and enhance the absorption and conversion capability of polysulfides in the host structure.     

Frogspawn‐Coral‐Like Hollow Sodium Sulfide Nanostructured Cathode for High‐Rate Performance Sodium–Sulfur Batteries

Room‐temperature (RT) sodium–sulfur (Na–S) batteries are attractive cost‐effective platforms as the next‐generation energy storage systems by using all earth‐abundant resources as electrode materials. However, the slow kinetics of Na–S chemistry makes it hard to achieve high‐rate performance. Herein, a facile and scalable approach has been developed to synthesize hollow sodium sulfide (Na₂S) nanospheres embedded in a highly hierarchical and spongy conductive carbon matrix, forming an intriguing architecture similar to the morphology of frogspawn coral, which has shown great potential as a cathode for high‐rate performance RT Na–S batteries. The shortened Na‐ion diffusion pathway benefits from the hollow structures together with the fast electron transfer from the carbon matrix contributes to high electrochemical reactivity, leading to superior electrochemical performance at various current rates. At high current densities of 1.4 and 2.1 A g^?1, high initial discharge capacities of 980 and 790 mAh g^?1_sulfur can be achieved, respectively, with reversible capacities stabilized at 600 and 400 mAh g^?1_sulfur after 100 cycles. As a proof of concept, a Na‐metal‐free Na–S battery is demonstrated by pairing the hollow Na₂S cathode with tin‐based anode. This work provides guidance on rational materials design towards the success of RT high‐rate Na–S batteries.     

Porphyrin‐Derived Graphene‐Based Nanosheets Enabling Strong Polysulfide Chemisorption and Rapid Kinetics in Lithium–Sulfur Batteries

Lithium–sulfur (Li–S) batteries hold great promise as a next‐generation battery system because of their extremely high theoretical energy density and low cost. However, ready lithium polysulfide (LiPS) diffusion and sluggish redox kinetics hamper their cyclability and rate capability. Herein, porphyrin‐derived graphene‐based nanosheets (PNG) are proposed for Li–S batteries, which are achieved by pyrolyzing a conformal and thin layer of 2D porphyrin organic framework on graphene to form carbon nanosheets with a spatially engineered nitrogen‐dopant‐enriched skin and a highly conductive skeleton. The atomic skin is decorated with fully exposed lithiophilic sites to afford strong chemisorption to LiPSs and improve electrolyte wettability, while graphene substrate provides speedy electron transport to facilitate redox kinetics of sulfur species. The use of PNG as a lightweight interlayer enables efficient operation of Li–S batteries in terms of superb cycle stability (cyclic decay rate of 0.099% during 300 cycles at 0.5 C), good rate capability (988 mAh g^?1 at 2.0 C), and impressive sulfur loading (areal capacity of 8.81 mAh cm^?2 at a sulfur loading of 8.9 mg cm^?2). The distinct interfacial strategy is expected to apply to other conversion reaction batteries relying on dissolution–precipitation mechanisms and requiring interfacial charge‐ and mass‐transport‐mediation concurrently.     

Metal Sulfide‐Decorated Carbon Sponge as a Highly Efficient Electrocatalyst and Absorbant for Polysulfide in High‐Loading Li2S Batteries

Owing to its high theoretical specific capacity (1166 mA h g^?1) and particularly its advantage to be paired with a lithium‐metal‐free anode, lithium sulfide (Li₂S) is regarded as a much safer cathode for next‐generation advanced lithium–sulfur (Li–S) batteries. However, the low conductivity of Li₂S and particularly the severe “polysulfide shuttle” of lithium polysulfide (LiPS) dramatically hinder their practical application in Li–S batteries. To address such issues, herein a bifuctional 3D metal sulfide‐decorated carbon sponge (3DTSC), which is constructed by 1D carbon nanowires cross‐linked with 2D graphene nanosheets with high conductivity and polar 0D metal sulfide nanodots with efficient electrocatalytic activity and strong chemical adsorption capability for LiPSs, is presented. Benefiting from the well‐designed multiscale, multidimensional 3D porous nanoarchitecture with high conductivity, and efficient electrocatalytic and absorption ability, the 3DTSC significantly mitigates LiPS shuttle, improves the utilization of Li₂S, and facilitates the transport of electrons and ions. As a result, even with a high Li₂S loading of 8 mg cm^?2, the freestanding 3DTSC‐Li₂S cathode without a polymer binder and metallic current collector delivers outstanding electrochemical performance with a high areal capacity of 8.44 mA h cm^?2.     

Long Cycle Life,Low Self‐Discharge Sodium–Selenium Batteries with High Selenium Loading and Suppressed Polyselenide Shuttling

The use of selenium as a cathode in rechargeable sodium–selenium batteries is hampered by low Se loading, inferior electrode kinetics, and polyselenide shuttling between the cathode and anode. Here a high‐performance sodium–selenium cell is presented by coupling a binder‐free, self‐interwoven carbon nanofiber–selenium cathode with a light‐weight carbon‐coated bifunctional separator. With this strategy, electrodes with a high Se mass loading (4.4 mg cm^?2) render high reversible capacities of 599 mA h g^?1 at 0.1C rate and 382 mA h g^?1 at 5C rate. In addition, this novel cell offers good shelf‐life with a low self‐discharge, retaining 93.4% of its initial capacity even after resting for six months. As evidenced by experimental and density functional theory analysis, the remarkable dynamic (cycle life) and static (shelf‐life) stabilities originate from the high electrical conductivity, improved Na‐ion accessibility through the 3D interconnected open channels, and highly restrained polyselenide shuttle. The results demonstrate the viability of high‐performance sodium–selenium batteries with high selenium loading.