Methane fermentation of Japanese cedar wood pretreated with a white rot fungus, Ceriporiopsis subvermispora

Methane fermentation of Japanese cedar wood was carried out after pretreatment with four strains of white rot fungi, Ceriporiopsis subvermispora ATCC 90467, CZ-3, CBS 347.63 and Pleurocybella porrigens K-2855. These fungi were cultivated on wood chip media with and without wheat bran for 4-8 weeks. The pretreated wood chip was fermented anaerobically with sludge from a sewage treatment plant. Pretreatments with C. subvermispora ATCC 90467, CZ-3 and CBS 347.63 in the presence of wheat bran for 8 weeks decreased 74-76% of beta-O-4 aryl ether linkages in the lignin to accelerate production of methane. After fungal treatments with C. subvermispora ATCC 90467 and subsequent 30-days methane fermentation, the methane yield reached 35 and 25% of the theoretical yield based on the holocellulose contents of the decayed and original wood, respectively. In contrast, treatment with the three strains of C. subvermispora without wheat bran cleaved 15-26% of the linkage and produced 6-9% of methane. There were no significant accelerating effects in wood chips treated with P. porrigens which has a lower ability to decompose the lignin. Thus, it was found that C. subvermispora, with a high ability to decompose aryl ether bonds of lignin, promoted methane fermentation of softwood in the presence of wheat bran.     

Evaluation of a combined brown rot decay–chemical delignification process as a pretreatment for bioethanol production from Pinus radiata wood chips

Wood chips of Pinus radiata softwood were biotreated with the brown rot fungus (BRF) Gloeophyllum trabeum for periods from 4 and 12 weeks. Biodegradation by BRF leads to an increase in cellulose depolymerization with increasing incubation time. As a result, the intrinsic viscosity of holocellulose decreased from 1,487 cm³/g in control samples to 783 and 600 cm³/g in 4- and 12-week decayed wood chips, respectively. Wood weight and glucan losses varied from 6 to 14% and 9 to 21%, respectively. Undecayed and 4-week decayed wood chips were delignified by alkaline (NaOH solution) or organosolv (ethanol/water) processes to produced cellulosic pulps. For both process, pulp yield was 5–10% lower for decayed samples than for control pulps. However, organosolv bio-pulps presented low residual lignin amount and high glucan retention. Chemical pulps and milled wood from undecayed and 4-week decayed wood chips were pre-saccharified with cellulases for 24 h at 50°C followed by simultaneous saccharification and fermentation (SSF) with the yeast Saccharomyces cerevisiae IR2-9a at 40°C for 96 h for bioethanol production. Considering glucan losses during wood decay and conversion yields from chemical pulping and SSF processes, no gains in ethanol production were obtained from the combination of BRF with alkaline delignification; however, the combination of BRF and organosolv processes resulted in a calculated production of 210 mL ethanol/kg wood or 72% of the maximum theoretically possible from that pretreatment, which was the best result obtained in the present study.     

Time course of fungal removal of lipophilic extractives from Eucalyptus globulus wood

Free and esterified sitosterol, the main lipophilic constituents of eucalypt wood extractives, have been associated with the formation of pitch deposits during manufacturing of environmentally-sound paper pulp from Eucalyptus globulus wood. These, and other lipophilic compounds, were analyzed by gas chromatography-mass spectrometry in the course of wood treatments (up to 7 weeks) with four extractive-degrading fungi in order to optimize biotechnological control of pitch deposition in eucalypt pulp (with moderate loss of wood weight). In contrast to commercialized fungi used in pitch control, which are not able to degrade sitosterol, the fungi investigated in this paper produced a rapid decline of both free and esterified sterols in wood. The degradation rate of steroid hydrocarbons and squalene was moderate, and the amount of steroid ketones (probably formed during oxidative degradation of steroids) and triglycerides increased at different stages of wood treatment. Up to 95% removal of total steroids (including free and esterified sterols, steroid ketones and steroid hydrocarbons) by fungi was obtained at the end of wood treatment under the solid-state fermentation conditions used. The most promising results from the point of view of industrial applicability, however, were obtained after 1-2 weeks of treatment with either Phlebia radiata or Poria subvermispora, which enabled 70% steroid removal with a moderate wood weight loss of 1-4%.     

Assessment of wood-inhabiting Basidiomycetes for biokraft pulping of softwood chips

Wood-inhabiting Basidiomycetes have been screened for various applications in the pulp and paper industry and it is evident that different fungi need to be used to suit the specific requirements of each application. This study assessed the suitability of 278 strains of South African wood-decay fungi for the pre-treatment of softwood chips for kraft pulping. The influence of these fungi on kappa number, yield and strength properties of pulp was evaluated. A number of these strains were more efficient in reducing kappa number than the frequently used strains of Phanerochaete chrysosporium and Ceriporiopsis subvermispora. Six strains of Stereum hirsutum and a strain of an unidentified species were able to reduce the kappa number significantly without a significant influence on the pulp yield. Treatment of wood with two strains of S. hirsutum, one strain of Peniophora sp. and a strain of an unidentified species resulted in paper with improved strength properties.     

Biological pretreatment of softwood Pinus densiflora by three white rot fungi

The effects of biological pretreatment on the Japanese red pine Pinus densiflora, was evaluated after exposure to three white rot fungi Ceriporia lacerata, Stereum hirsutum, and Polyporus brumalis. Change in chemical composition, structural modification, and their susceptibility to enzymatic saccharification in the degraded wood were analyzed. Of the three white rot fungi tested, S. hirsutum selectively degraded the lignin of this sortwood rather than the holocellulose component. After eight weeks of pretreatment with S. hirsutum, total weight loss was 10.7%, while lignin loss was the highest at 14.52% among the tested samples. However, holocellulose loss was lower at 7.81% compared to those of C. lacerata and P. brumalis. Extracelluar enzymes from S. hirsutum showed higher activity of ligninase and lower activity of cellulase than those from other white rot fungi. Thus, total weight loss and changes in chemical composition of the Japanese red pine was well correlated with the enzyme activities related with lignin- and cellulose degradation in these fungi. Based on the data obtained from analysis of physical characterization of degraded wood by X-ray Diffractometry (XRD) and pore size distribution, S. hirsutum was considered as an effective potential fungus for biological pretreatment. In particular, the increase of available pore size of over 120 nm in pretreated wood powder with S. hirsutum made enzymes accessible for further enzymatic saccharification. When Japanese red pine chips treated with S. hirsutum were enzymatically saccharified using commercial enzymes (Cellulclast 1.5 L and Novozyme 188), sugar yield was greatly increased (21.01%) compared to non-pretreated control samples, indicating that white rot fungus S. hirsutum provides an effective process in increasing sugar yield from woody biomass.     

Production of new unsaturated lipids during wood decay by ligninolytic basidiomycetes

Lipids were analyzed by gas chromatography-mass spectrometry for a 7-week in vitro decay of eucalypt wood by four ligninolytic basidiomycetes. The sound wood contained up to 75 mg of lipophilic compounds per 100 g of wood. Hydrolysis of sterol esters, which represented 38% of total wood lipids, occurred during the fungal decay. The initial increase of linoleic and other free unsaturated fatty acids paralleled the decrease of sterol esters. Moreover, new lipid compounds were found at advanced stages of wood decay that were identified from their mass spectra as unsaturated dicarboxylic acids consisting of a long aliphatic chain attached to the C-3 position of itaconic acid. These dicarboxylic acids were especially abundant in the wood treated with Ceriporiopsis subvermispora (up to 24 mg per 100 g of wood) but also were produced by Phlebia radiata, Pleurotus pulmonarius, and Bjerkandera adusta. We hypothesize that three main alkylitaconic acids (tetradecylitaconic, cis-7-hexadecenylitaconic, and hexadecylitaconic acids) are synthesized by fungi in condensation reactions involving palmitic, oleic, and stearic acids. We suggest that both wood unsaturated fatty acids (present in free form or released from esters during natural decay) and unsaturated metabolites synthesized by fungi could serve as a source for peroxidizable lipids in lignin degradation by white rot basidiomycetes.     

Ceriporic acid B, an extracellular metabolite of Ceriporiopsis subvermispora, suppresses the depolymerization of cellulose by the Fenton reaction

The white rot fungus, Ceriporiopsis subvermispora, is able to degrade lignin in wood without intensive damage to cellulose. Since lignin biodegradation by white rot fungi proceeds by radical reactions, accompanied by the production of a large amount of Fe3+-reductant phenols and reductive radical species in the presence of iron ions, molecular oxygen, and H2O2, C. subvermispora has been proposed to possess a biological system which suppresses the production of a cellulolytic active oxygen species, *OH, by the Fenton reaction. In the present paper, we demonstrate that 1-nonadecene-2,3-dicarboxylic acid (ceriporic acid B), an extracellular metabolite of C. subvermispora, strongly inhibited *OH production and the depolymerization of cellulose by the Fenton reaction in the presence of iron ions, cellulose, H2O2, and a reductant for Fe3+, hydroquinone (HQ), at the physiological pH of the fungus.     

Patterns of lignin degradation and oxidative enzyme secretion by different wood- and litter-colonizing basidiomycetes and ascomycetes grown on beech-wood

The degradation of lignocellulose and the secretion of extracellular oxidoreductases were investigated in beech-wood (Fagus sylvatica) microcosms using 11 representative fungi of four different ecophysiological and taxonomic groups causing: (1) classic white rot of wood (e.g. Phlebia radiata), (2) 'nonspecific' wood rot (e.g. Agrocybe aegerita), (3) white rot of leaf litter (Stropharia rugosoannulata) or (4) soft rot of wood (e.g. Xylaria polymorpha). All strong white rotters produced manganese-oxidizing peroxidases as the key enzymes of ligninolysis (75-2200 mU g(-1)), whereas lignin peroxidase activity was not detectable in the wood extracts. Interestingly, activities of two recently discovered peroxidases - aromatic peroxygenase and a manganese-independent peroxidase of the DyP-type - were detected in the culture extracts of A. aegerita (up to 125 mU g(-1)) and Auricularia auricula-judae (up to 400 mU g(-1)), respectively. The activity of classic peroxidases correlated to some extent with the removal of wood components (e.g. Klason lignin) and the release of small water-soluble fragments (0.5-1.0 kDa) characterized by aromatic constituents. In contrast, laccase activity correlated with the formation of high-molecular mass fragments (30-200 kDa). The differences observed in the degradation patterns allow to distinguish the rot types caused by basidiomycetes and ascomycetes and may be suitable for following the effects of oxidative key enzymes (ligninolytic peroxidases vs. laccases, role of novel peroxidases) during wood decay.     

Enzymatic properties of two beta-glucosidases from Ceriporiopsis subvermispora produced in biopulping conditions

AIMS: Ceriporiopsis subvermispora produces endoglucanase and beta-glucosidase when cultivated on cellulose or wood, but biodegradation of cellulose during biopulping by C. subvermispora is low even after long periods. To resolve this discrepancy, we grew C. subvermispora on Pinus taeda wood chips and purified the major beta-glucosidases it produced. Kinetic parameters were determined to clear if this fungus produces enzymes capable of yielding assimilable glucose from wood. METHODS AND RESULTS: Ceriporiopsis subvermispora was grown on P. taeda wood chips under solid-state fermentation. After 30 days, the crude extract obtained from enzyme extraction with sodium acetate buffer 50 mmol l(-1), pH 5.4, was filtrated in membranes with a molecular mass exclusion limit of 100 kDa. Enzyme purification was carried out using successively Sephacryl S-300 gel filtration. The retained fraction attained 76% of beta-glucosidase activity with 3.7-fold purification. Two beta-glucosidases were detected with molecular mass of 110 and 53 kDa. We have performed a characterization of the enzymatic properties of the beta-glucosidase of 110 kDa. The optimum pH and temperature were 3.5 and 60 degrees C, respectively. The K(m) and V(max) values were respectively 3.29 mmol l(-1) and 0.113 micromol min(-1) for the hydrolysis of p-nitrophenyl-beta-glucopyranoside (pNPG) and 2.63 mmol l(-1) and 0.103 micromol min(-1), towards cellobiose. beta-Glucosidase activity was strongly increased by Mn(2+) and Fe(3+), while Cu(2+) severely inhibited it. CONCLUSIONS: Ceriporiopsis subvermispora produces small amounts of beta-glucosidase when grown on wood. The gel filtration and polyacrylamide gel electrophoresis data revealed the existence of two beta-glucosidases with 110 and 53 kDa. The 110 kDa beta-glucosidase from C. subvermispora can be efficiently purified in a single step by gel filtration chromatography. The enzyme has an acid pH optimum with similar activity on pNPG and cellobiose and is thus typical beta-glucosidase. SIGNIFICANCE AND IMPACT OF THE STUDY: Ceriporiopsis subvermispora produces beta-glucosidase with limited action during wood decay making able its use for the production of biomechanical and biochemical pulps. The results presented in this paper show the importance of studying the behaviour of beta-glucosidases during biopulping.     

Qualitative and quantitative changes of beech wood degraded by wood-rotting basidiomycetes monitored by Fourier transform infrared spectroscopic methods and multivariate data analysis

Beech wood (Fagus sylvatica L.) veneers were cultivated with white and brown rot fungi for up to 10 weeks. Fungal wood modification was traced with Fourier transform near infrared (FT-NIR) and Fourier transform mid infrared (FT-MIR) methods. Partial least square regression (PLSR) models to predict the total lignin content before and after fungal decay in the range between 17.0% and 26.6% were developed for FT-MIR transmission spectra as well as for FT-NIR reflectance spectra. Weight loss of the decayed samples between 0% and 38.2% could be estimated from the wood surface using individual PLSR models for white rot and brown rot fungi, and from a model including samples subjected to both degradation types.     

Two-stage fungal biopulping for improved enzymatic hydrolysis of wood

A novel two-stage, whole organism fungal biopulping method was examined for increasing the yield of enzymatic hydrolysis of wood into soluble glucose. Liriodendron tulipifera wood chips (1 g) were exposed to liquid culture suspensions of white rot (Ceriporiopsis subvermispora) or brown rot (Postia placenta) fungi and incubated at 28 °C, either alone in single-stage 30 day (one fungal species applied) or two-stage 60 day (both fungal species applied in alternative succession) treatments. Fungi grew in all treatments, but did not significantly decrease the percent carbohydrate content of the wood. Two-stage treatments differed significantly in mass loss depending on order of exposure, suggesting additive or inhibitory fungal interactions occurred. Treatments consisting of C. subvermispora followed by P. placenta exhibited 6 ± 0.5% mass loss and increased the yield of enzymatic hydrolysis by 67-119%. This significant hydrolysis improvement suggests that fungal biopulping technologies could support commercial lignocellulosic ethanol production efforts if further developed.     

Decay resistance of ash,beech and maple wood modified with N-methylol melamine and a metal complex dye

This study evaluated the decay resistance of ash (Fraxinus excelsior L.), beech (Fagus sylvatica L.), and maple (Acer platanoides L.) wood impregnated by a full cell process with N-methylol melamine (NMM) and combined NMM-metal complex dye (NMM-BS) in aqueous solutions. Basidiomycete decay testing involved incubation with Coniophora puteana (brown rot) and Trametes versicolor (white rot) according to a modified EN 113 (1996) standard, while for the soft rot fungal resistance was evaluated following the standard ENv 807 (2001). NMM and NMM-BS modifications at a WPG range of 7–11% provided decay protection against brown rot resulting in a mass loss less than the required limit (3%). The NMM and NMM-BS modified wood showed increased resistance to white rot decay; however, a higher WPG is needed to prohibit attack from this hardwood specific fungus. The metal-complex dye alone revealed biocidal effects against basidiomycetes. An increased WPG in NMM or NMM-BS had a positive impact against soft rot decay and the lowest mass losses after 32 weeks of exposure were obtained with NMM modification at about 18–21% WPG. NMM modification at this WPG range, however, was not sufficient to protect the wood from soft rot decay. The wood of beech and maple showed slightly higher resistance to all decay types than ash, probably due to the poorer degree of modification of the latter.     

Biopulping: An overview of developments in an environmentally safe paper-making technology

Abstract: Treatment of wood chips with lignin-degrading fungi prior to pulping has been shown to have great potential for mechanical as well as chemical pulping on a laboratory scale. Ceriporiopsis subvermispora , when grown on aspen or loblolly pine for 4 weeks, was found to be superior to other fungi. On aspen there was an energy savings of 47%, and an increase in burst and tear indices of 22% and 119%, respectively. With loblolly pine, energy savings amounted to 37%, while burst and tear indices increased by 41% and 54%, respectively. The weight loss was only 6%, but a decrease in optical properties had to be accepted. After sulfite cooking of wood chips pretreated for 2 weeks, the Kappa number decreased by 30% with hard- and softwood. Tensile and tear indices decreased by only 10%, while the brightness of unbleached pulp increased by 4% with birch. Information obtained by immunoelectron microscopy and differential staining led to the conclusion that the biopulping effect obtained after 2 weeks of incubation cannot be explained by the direct action of enzymes on lignin or polysaccharides. Instead, a low molecular mass agent is considered to be responsible for the biopulping effect. These results have changed the aims of biopulping from an emphasis on removing the bulk of lignin to an emphasis on a short-term process, lasting 2 weeks and yielding a low mass loss. Data on these kinetics of fungal development and the degree of asepsis will help to scale-up the process. An advanced chip pile is assumed to be the most feasible process design, rather than a controlled enclosed reactor.     

Montan wax improves performance of boron-based wood preservatives

Importance of boron compounds in wood preservation is increasing due to their low environmental impact, high efficacy and the fact that many other active ingredients have been removed from the market after the introduction of the Biocidal Products Directive. The most important drawback of boron is prominent leaching in wet environment. In order to improve their fixation, and performance against wood decay fungi, boric acid was combined with montan wax emulsion. Possible synergistic effects of boric acid and montan wax were determined according to modified EN 113 procedure. Norway spruce and beech wood specimens were exposed to three white rot (Trametes versicolor, Pleurotus ostreatus and Hypoxylon fragiforme) and brown rot wood decay fungi (Gloeophyllum trabeum, Antrodia vaillantii and Serpula lacrymans) for 12 weeks. Boron leaching from vacuum/pressure treated Norway spruce wood was determined according to the continuous (EN 84 and ENV 1250-2) and non-continuous (OECD and prCEN/TS 15119-1) procedures. Boron was determined with ICP mass spectrometry in collected leachates. The results of the fungicidal tests clearly showed that montan wax emulsion and boric acid act synergistically against tested wood decay fungi. Approximately 50% lower boric acid retentions are required in combination with montan wax emulsions to achieve sufficient protection against wood rotting fungi. However, it is even more important that all leaching tests performed proved that the addition of montan wax decreased boron leaching from impregnated specimens for 20% up to 50%.     

Biopulping process design and kinetics

Biopulping is the solid-state fermentation of wood chips as a pretreatment for mechanical pulping processes. The two organisms that are currently of the greatest interest for biopulping are the white-rot fungi, Phanerochaete chrysosporium and Ceriporiopsis subvermispora. P. chrysosporium has been shown to successfully biopulp wood (33% energy savings; 39% improvement in tear index) without the need for sterilization of the wood or nutrient supplementation. Demonstrating the practical and economical feasibility of the biopulping process requires process modeling based on accurate kinetic data. Techniques to monitor dry weight loss and growth rate as functions of time using carbon dioxide production data have been developed. Growth was shown to be linear with time on unsupplemented chips and exponential with time on supplemented chips.     

Delignification of Wood Chips and Pulps by Using Natural and Synthetic Porphyrins: Models of Fungal Decay

Kraft pulps, prepared from softwoods, and small chips of birch wood were treated with heme and tert-butyl hydroperoxide in aqueous solutions at reflux temperature. Analyses of treated pulps showed decreases in kappa number (a measure of lignin content) from about 36 to less than 2, with concomitant increases in brightness (80% increase in the better samples). Analyses of treated wood chips revealed selective delignification and removal of hemicelluloses. After 48 h of treatment, lignin losses from the wood chips approached 40%, and xylose/mannose (hemicellulose) losses approached 70%, while glucose (cellulose) losses were less than 10%. Examination of delignified chips by transmission electron microscopy showed that the removal of lignin occurred in a manner virtually indistinguishable from that seen after decay by white rot fungi. Various metalloporphyrins, which act as biomimetic catalysts, were compared to horseradish peroxidase and fungal manganese peroxidase in their abilities to oxidize syringaldazine in an organic solvent, dioxane. The metalloporphyrins and peroxidases behaved similarly, and it appeared that the activities of the peroxidases resulted from the extraction of heme into the organic phase, rather than from the activities of the enzymes themselves. We concluded that heme-tert-butyl hydroperoxide systems in the absence of a protein carrier mimic the decay of lignified tissues by white rot fungi.     

Microbial scission of sulfide linkages in vulcanized natural rubber by a white rot basidiomycete, Ceriporiopsis subvermispora

A white rot basidiomycete, Ceriporiopsis subvermispora, degraded vulcanized natural rubber (NR) sheets on a wood medium. The fungus decreased the total sulfur content of the rubber by 29% in 200 days, accompanied by the cleavage of sulfide bonds between polyisoprene chains. X-ray photoelectron spectroscopy (XPS) demonstrated that C. subvermispora reduced the frequency of S-C bonds by 69% with a concomitant formation of S-O bonds during the culture period. Dipolar decoupling/magic angle spinning (DD/MAS) solid state 13C NMR revealed that the fungus preferentially decomposed monosulfide bonds linked to a cis- and trans-1,4-isoprene backbone but the cleavage of polysulfide bonds was also observed. In contrast, no decrease in weight or devulcanization of rubber was observed in cultures of a white rot fungus, Dichomitus squalens. The oxidative cleavage of sulfide bonds by C. subvermispora demonstrates that ligninolytic basidiomycetes are potential microbes for the biological devulcanization of rubber products.     

Lignin degradation by white rot fungi on spruce wood shavings during short-time solid-state fermentations monitored by near infrared spectroscopy

Due to their outstanding capability of degrading the recalcitrant biomacromolecule lignin, white rot fungi have been attracting interest for several technological applications in mechanical pulping and wood surface modification. However, little is known about the time course of delignification in early stages of colonisation of wood by these fungi. Using a Fourier transform near infrared (FT-NIR) spectroscopic technique, lignin loss of sterilised spruce wood shavings (0.4–2.0 mm particle size) that had been degraded by various species of white rot fungi could be monitored already during the first 2 weeks. The delignification kinetics of Dichomitus squalens, three Phlebia species (Phlebia brevispora, Phlebia radiata and Phlebia tremellosa), three strains of Ceriporiopsis subvermispora as well as the white rot ascomycete Hypoxylon fragiforme and the basidiomycete Oxyporus latemarginatus were determined. Each of the fungi tested was able to reduce the lignin content of spruce wood significantly during the first week. The amount of delignification achieved by the selected white rot fungi after 2 weeks ranged from 7.2% for C. subvermispora (FPL 105.752) to 2.5% for P. radiata. Delignification was significant (P = 95%) already after 3 days treatment with C. subvermispora and P. tremellosa. Activities of extracellular ligninolytic enzymes (laccase, manganese peroxidase and/or lignin peroxidase), expressed by each of the tested fungi, were determined. Lignin was degraded when peroxidase activity was detected in the fungal cultures, but only a low level of correlation between enzyme activities and the extent of delignification was found.     

Evaluation of the selectivity of white rot isolates using near infrared spectroscopic techniques

Seventeen isolates from white rotted beech wood and six strains from a local culture collection were evaluated for their capability to delignify beech and spruce wood selectively. Six peroxidase-positive isolates were found using a colorimetric agar plate test (Poly R-478), and genetically identified by their internal transcribed spacer (ITS1) or 28S rDNA sequences. Colonised on beech and spruce wood veneers, some of the peroxidase-positive isolates caused selective white rot on both wood species. Weight loss and lignin content of the degraded veneers were estimated from FT-NIR spectra with established linear regression models and multivariate models based on partial least squares regression (PLSR). Weight loss of the samples was also determined gravimetrically. A measure for the relative selectivity of the strains for lignin degradation was formulated and the values were calculated. Two strains that were identified as Oxyporus latemarginatus and Trametes cervina exhibited high selectivity on spruce wood, but the lignin content of the decayed wood was higher than that degraded by the reference strain Ceriporiopsis subvermispora. One strain – identified as Phlebia tremellosa – led to a lower lignin content of beech wood but caused also comparably high weight loss and thus exhibited an overall lower selectivity. The NIR spectroscopic method proved to be convenient for the quick screening of selective white rot fungi. Furthermore, the results revealed that high selectivity for lignin degradation is much more pronounced in early degradation stages.     

Alterations in structure, chemistry, and biodegradability of grass lignocellulose treated with the white rot fungi Ceriporiopsis subvermispora and Cyathus stercoreus.

The white rot fungi Ceriporiopsis subvermispora FP-90031-sp and Cyathus stercoreus ATCC 36910 were evaluated for their ability to delignify Bermuda grass (Cynodon dactylon) stems and improve biodegradability. Compositional and structural alterations in plant cell walls effected by the fungi were determined by nuclear magnetic resonance spectroscopy, gas chromatography of alkali-treated residues, microspectrophotometry, and electron microscopy. Contaminating bacteria and fungi, which grew from unsterilized Bermuda grass stems, did not alter the improvement in grass biodegradability by either of the fungi from that of gas-sterilized stems. The biodegradation of stems by ruminal microorganisms, after treatment for 6 weeks with C. subvermispora or C. stercoreus, was improved by 29 to 32% and by 63 to 77%, respectively; dry weight losses caused by pretreatment with the fungi were about 20% over that in untreated, control stems. Both fungi preferentially removed aromatics to carbohydrates, and C. subvermispora removed proportionately more guaiacyl units than did C. stercoreus. Substantial amounts of ester-linked p-coumaric and ferulic acids were removed by both fungi, and about 23 and 41% of total aromatics (determined after 4 M NaOH direct treatment) were removed from the plant biomass after incubation with C. subvermispora and C. stercoreus, respectively. UV absorption microspectrophotometry indicated that ester-linked phenolic acids were totally removed from the parenchyma cell walls, and these cells were readily and completely degraded by both fungi. However, aromatic constituents were only partially removed from the more recalcitrant sclerenchyma cell walls, resulting in variation in electron density and random digestion pits after incubation with fiber-degrading bacteria.(ABSTRACT TRUNCATED AT 250 WORDS)