An instrumented tissue tester for measuring soft tissue property under the metatarsal heads in relation to metatarsophalangeal joint angle

Identification of the localized mechanical response of the plantar soft tissue pads underneath the metatarsal heads (i.e., sub-MTH pad) to external loading is key to understand and predict how it functions in a gait cycle. The mechanical response depends on various parameters, such as the external load (direction and rate), the sub-MTH tissue properties (anisotropy and viscoelasticity), and the configuration of the metatarsophalangeal (MTP) joint overlying the tissue. In this study, an instrument-driven tissue tester that incorporates a portable motorized indentor within a special foot positioning apparatus was developed for realistic in vivo mechanical characterization (i.e. tissue stiffness and force relaxation behavior) of the local sub-MTH pad with the MTP joint configured at various dorsiflexion angles associated with gait. The tester yields consistent results for tests on the 2nd sub-MTH pad. Measurement errors for the initial stiffness (for indentation depths ≤ 1 mm), end-point stiffness, and percentage force relaxation were less than 0.084 N/mm, 0.133 N/mm, and 0.127%, respectively, across all test configurations. The end-point tissue stiffness, which increased by 104.2% due to a 50° MTP joint dorsiflexion, also agreed with a previous investigation. In vivo tissue's force relaxation was shown to be pronounced (avg. = 8.1%), even for a short holding-time interval. The proposed technique to facilitate study of the dependence of the local sub-MTH pad and tissue response on the MTP joint angle might be preferable to methods that focus solely on measurement of tissue property because under physiologic conditions the sub-MTH pad elasticity may vary in gait, to adapt to drastically changing mechanical demands in the sub-MTH region of the terminal stance-phase, where MTP joint dorsiflexion occurs.     

Soft tissue stiffness over the hip increases with age and its implication in hip fracture risk in older adults

Risk of hip fracture depends on the bone strength as well as the impact force delivered to the proximal femur during falls, and femoral soft tissue may help to reduce the hip fracture risk by attenuating the impact force. Femoral soft tissue stiffness was measured from a large sample, and compared how this was affected by age, gender and site.One hundred fifty healthy individuals (fifty-two young (aged between 19 and 29), forty-eight middle-aged (30–64), and fifty old (over 65)) participated. Each age group included an equal number of males and females. Using an automated hand-held indentation device, soft tissue stiffness was measured over twelve sites with respect to the greater trochanter (GT).For both left and right hips, the stiffness was associated with age (p < 0.0005), gender (p < 0.0005), and site (p < 0.0005). On average, the stiffness was 26% greater in older than young adults (321.5 versus 254.3 N/m). On average across twelve sites, the regression analysis indicated that the stiffness increases 1.33 N/m every year (“soft tissue stiffness over the hip = 1.33*age + 221.8”; R = 0.518, p < 0.0005). Furthermore, the stiffness was 18% greater in male than female (308.8 versus 262.6 N/m), and differed across twelve sites over the hip, being greatest (424.2 N/m) at the GT, and least (206.3 N/m) at the superior gluteal region.The results provide insights into the shock absorbing property of soft tissue over the hip, and inform the improvement of fall-related injury prevention interventions (i.e., hip protector, safe landing strategies) in older adults.     

Region-specific constitutive modeling of the plantar soft tissue

Recent research has shown that hyperelastic properties of the plantar soft tissue consisting of adipose tissue and fibrous septa change from region to region. However, relatively little research has been conducted to develop analytical or computational models to describe the region-specific behavior of the plantar soft tissue. The objective of the research is to develop a region-specific constitutive model of the plantar soft tissue. Plantar soft tissue specimens were dissected from six regions [subcalcaneal (CA), sublateral (LA), subnavicular (Nav), 1st, 3rd, and 5th submetatarsal (M1, M3, M5)] from cadaveric foot samples, and a picrosirius red staining technique was used to visualize the collagen fibers in fibrous septa. The volume fractions of adipose tissue and fibrous septa and the volume fractions of the principal orientations of the fibrous septa were calculated with the intensity gradient method. Region-specific constitutive models were then developed in finite element analysis considering the microstructure of the plantar soft tissue. The hyperelastic region specific material properties of the plantar soft tissue were validated with experimental unconfined compression tests and indentation tests from the literature. The results show that the models give reasonable predictions of the stiffness of the soft tissue within a standard deviation of the tests. The region-specific constitutive models help to explain how changes in the constituents are related to mechanical behavior of the soft tissue on a region specific basis.     

The bending stiffness of shoes is beneficial to running energetics if it does not disturb the natural MTP joint flexion

A local minimum for running energetics has been reported for a specific bending stiffness, implying that shoe stiffness assists in running propulsion. However, the determinant of the metabolic optimum remains unknown. Highly stiff shoes significantly increase the moment arm of the ground reaction force (GRF) and reduce the leverage effect of joint torque at ground push-off. Inspired by previous findings, we hypothesized that the restriction of the natural metatarsophalangeal (MTP) flexion caused by stiffened shoes and the corresponding joint torque changes may reduce the benefit of shoe bending stiffness to running energetics. We proposed the critical stiffness, k_cr, which is defined as the ratio of the MTP joint (MTPJ) torque to the maximal MTPJ flexion angle, as a possible threshold of the elastic benefit of shoe stiffness. 19 subjects participated in a running test while wearing insoles with five different bending stiffness levels. Joint angles, GRFs, and metabolic costs were measured and analyzed as functions of the shoe stiffness. No significant changes were found in the take-off velocity of the center of mass (CoM), but the horizontal ground push-offs were significantly reduced at different shoe stiffness levels, indicating that complementary changes in the lower-limb joint torques were introduced to maintain steady running. Slight increases in the ankle, knee, and hip joint angular impulses were observed at stiffness levels exceeding the critical stiffness, whereas the angular impulse at the MTPJ was significantly reduced. These results indicate that the shoe bending stiffness is beneficial to running energetics if it does not disturb the natural MTPJ flexion.     

Mutations in Desmin's Carboxy-Terminal “Tail” Domain Severely Modify Filament and Network Mechanics

Inherited mutations in the gene coding for the intermediate filament protein desmin have been demonstrated to cause severe skeletal and cardiac myopathies. Unexpectedly, some of the mutated desmins, in particular those carrying single amino acid alterations in the non-α-helical carboxy-terminal domain (“tail”), have been demonstrated to form apparently normal filaments both in vitro and in transfected cells. Thus, it is not clear if filament properties are affected by these mutations at all. For this reason, we performed oscillatory shear experiments with six different desmin “tail” mutants in order to characterize the mesh size of filament networks and their strain stiffening properties. Moreover, we have carried out high-frequency oscillatory squeeze flow measurements to determine the bending stiffness of the respective filaments, characterized by the persistence length l_p. Interestingly, mesh size was not altered for the mutant filament networks, except for the mutant DesR454W, which apparently did not form proper filament networks. Also, the values for bending stiffness were in the same range for both the “tail” mutants (l_p = 1.0-2.0 μm) and the wild-type desmin (l_p = 1.1 ± 0.5 μm). However, most investigated desmin mutants exhibited a distinct reduction in strain stiffening compared to wild-type desmin and promoted nonaffine network deformation. Therefore, we conclude that the mutated amino acids affect intrafilamentous architecture and colloidal interactions along the filament in such a way that the response to applied strain is significantly altered.In order to explore the importance of the “tail” domain as such for filament network properties, we employed a “tail”-truncated desmin. Under standard conditions, it formed extended regular filaments, but failed to generate strain stiffening. Hence, these data strongly indicate that the “tail” domain is responsible for attractive filament-filament interactions. Moreover, these types of interactions may also be relevant to the network properties of the desmin cytoskeleton in patient muscle.     

Three-dimensional finite element analysis of the foot during standing--a material sensitivity study

Information on the internal stresses/strains in the human foot and the pressure distribution at the plantar support interface under loading is useful in enhancing knowledge on the biomechanics of the ankle-foot complex. While techniques for plantar pressure measurements are well established, direct measurement of the internal stresses/strains is difficult. A three-dimensional (3D) finite element model of the human foot and ankle was developed using the actual geometry of the foot skeleton and soft tissues, which were obtained from 3D reconstruction of MR images. Except the phalanges that were fused, the interaction among the metatarsals, cuneiforms, cuboid, navicular, talus, calcaneus, tibia and fibula were defined as contact surfaces, which allow relative articulating movement. The plantar fascia and 72 major ligaments were simulated using tension-only truss elements by connecting the corresponding attachment points on the bone surfaces. The bony and ligamentous structures were embedded in a volume of soft tissues. The encapsulated soft tissue was defined as hyperelastic, while the bony and ligamentous structures were assumed to be linearly elastic. The effects of soft tissue stiffening on the stress distribution of the plantar surface and bony structures during balanced standing were investigated. Increases of soft tissue stiffness from 2 and up to 5 times the normal values were used to approximate the pathologically stiffened tissue behaviour with increasing stages of diabetic neuropathy. The results showed that a five-fold increase in soft tissue stiffness led to about 35% and 33% increase in the peak plantar pressure at the forefoot and rearfoot regions, respectively. This corresponded to about 47% decrease in the total contact area between the plantar foot and the horizontal support surface. Peak bone stress was found at the third metatarsal in all calculated cases with a minimal increase of about 7% with soft tissue stiffening.     

Functional Grading of Mineral and Collagen in the Attachment of Tendon to Bone

Attachment of dissimilar materials is a major challenge because high levels of localized stress may develop at their interfaces. An effective biologic solution to this problem exists at one of nature's most extreme interfaces: the attachment of tendon (a compliant, structural “soft tissue”) to bone (a stiff, structural “hard tissue”). The goal of our study was to develop biomechanical models to describe how the tendon-to-bone insertion derives its mechanical properties. We examined the tendon-to-bone insertion and found two factors that give the tendon-to-bone transition a unique grading in mechanical properties: 1), a gradation in mineral concentration, measured by Raman spectroscopy; and 2), a gradation in collagen fiber orientation, measured by polarized light microscopy. Our measurements motivate a new physiological picture of the tissue that achieves this transition, the tendon-to-bone insertion, as a continuous, functionally graded material. Our biomechanical model suggests that the experimentally observed increase in mineral accumulation within collagen fibers can provide significant stiffening of the partially mineralized fibers, but only for concentrations of mineral above a “percolation threshold” corresponding to formation of a mechanically continuous mineral network within each collagen fiber (e.g., the case of mineral connectivity extending from one end of the fiber to the other). Increasing dispersion in the orientation distribution of collagen fibers from tendon to bone is a second major determinant of tissue stiffness. The combination of these two factors may explain the nonmonotonic variation of stiffness over the length of the tendon-to-bone insertion reported previously. Our models explain how tendon-to-bone attachment is achieved through a functionally graded material composition, and provide targets for tissue engineered surgical interventions and biomimetic material interfaces.     

The compressive material properties of the plantar soft tissue

The plantar soft tissue is the primary means of physical interaction between a person and the ground during locomotion. Dynamic loads greater than body weight are borne across the entire plantar surface during each step. However, most testing of these tissues has concentrated on the structural properties of the heel pad. The purpose of this study was to determine the material properties of the plantar soft tissue from six locations beneath: the great toe (subhallucal), the 1st, 3rd and 5th metatarsal heads (submetatarsal), the lateral midfoot (lateral submidfoot) and the heel (subcalcaneal). We obtained specimens from these locations from 11 young, non-diabetic donors; the tissue was cut into 2 cm x 2 cm blocks and the skin was removed. Stress relaxation experiments were conducted and the data were fit using the quasi-linear viscoelastic (QLV) theory. To determine tissue modulus, energy loss and the effect of test frequency, we also conducted displacement controlled triangle waves at five frequencies ranging from 0.005 to 10 Hz. The subcalcaneal tissue was found to have an increased relaxation time compared to the other areas. The subcalcaneal tissue was also found to have an increased modulus and decreased energy loss compared to the other areas. Across all areas, the modulus and energy loss increased for the 1 and 10 Hz tests compared to the other testing frequencies. This study is the first to generate material properties for all areas of the plantar soft tissue, demonstrating that the subcalcaneal tissue is different than the other plantar soft tissue areas. These data will have implications for foot computational modeling efforts and potentially for orthotic pressure reduction devices.     

Control of dynamic foot-ground interactions in male and female soccer athletes: Females exhibit reduced dexterity and higher limb stiffness during landing

Controlling dynamic interactions between the lower limb and ground is important for skilled locomotion and may influence injury risk in athletes. It is well known that female athletes sustain anterior cruciate ligament (ACL) tears at higher rates than male athletes, and exhibit lower extremity biomechanics thought to increase injury risk during sport maneuvers. The purpose of this study was to examine whether lower extremity dexterity (LED) – the ability to dynamically control endpoint force magnitude and direction as quantified by compressing an unstable spring with the lower limb at submaximal forces – is a potential contributing factor to the “at-risk” movement behavior exhibited by female athletes. We tested this hypothesis by comparing LED-test performance and single-limb drop jump biomechanics between 14 female and 14 male high school soccer players. We found that female athletes exhibited reduced LED-test performance (p=0.001) and higher limb stiffness during landing (p=0.008) calculated on average within 51 ms of foot contact. Females also exhibited higher coactivation at the ankle (p=0.001) and knee (p=0.02) before landing. No sex differences in sagittal plane joint angles and center of mass velocity at foot contact were observed. Collectively, our results raise the possibility that the higher leg stiffness observed in females during landing is an anticipatory behavior due in part to reduced lower extremity dexterity. The reduced lower extremity dexterity and compensatory stiffening strategy may contribute to the heightened risk of ACL injury in this population.     

Comparison of three local frame definitions for the kinematic analysis of the fingers and the wrist

Because the hand is a complex poly-articular limb, numerous methods have been proposed to investigate its kinematics therefore complicating the comparison between studies and the methodological choices. With the objective of overcoming such issues, the present study compared the effect of three local frame definitions on local axis orientations and joint angles of the fingers and the wrist. Three local frames were implemented for each segment. The “Reference” frames were aligned with global axes during a static neutral posture. The “Landmark” frames were computed using palpated bony landmarks. The “Functional” frames included a flexion–extension axis estimated during functional movements. These definitions were compared with regard to the deviations between obtained local segment axes and the evolution of joint (Cardan) angles during two test motions. Each definition resulted in specific local frame orientations with deviations of 15° in average for a given local axis. Interestingly, these deviations produced only slight differences (below 7°) regarding flexion–extension Cardan angles indicating that there is no preferred method when only interested in finger flexion–extension movements. In this case, the Reference method was the easiest to implement, but did not provide physiological results for the thumb. Using the Functional frames reduced the kinematic cross-talk on the secondary and tertiary Cardan angles by up to 20° indicating that the Functional definition is useful when investigating complex three-dimensional movements. Globally, the Landmark definition provides valuable results and, contrary to the other definitions, is applicable for finger deformities or compromised joint rotations.     

Regional variations of in vivo surface stiffness of soft tissue layers of musculoskeletal extremities

Surface stiffness of bulk soft tissue in musculoskeletal extremities is important to consider in the design of prosthetics, exoskeletons, and protective gear. This knowledge is also foundational for surgical simulation and clinical interventions leveraging manipulation of the musculoskeletal surfaces. Injuries to musculoskeletal extremities are common and surgical and preventive interventions require interactions between various objects such as surgical tools and support surfaces with tissue boundaries. While a handful of investigations examined the variations in indentation mechanics due to pathology or injury specific sites, a comprehensive analysis across the surfaces of musculoskeletal extremities has not been completed. In this study we examine variations of surface stiffness across 8 sites of the upper and lower arms and legs for 95 subjects using an instrumented ultrasound device. Differences in surface stiffness were observed between gender, activity level, and indentation location groups. The lower arm posterior location had the highest average stiffness (3.89 × 10⁻³ MPa/mm), while the lowest stiffness was observed at the upper leg posterior location (0.98 × 10⁻³ MPa/mm). The differences between indentation sites were larger in magnitude when compared to differences due to demographics (gender and activity level). However the large ranges of the 95% confidence intervals suggest that an aggregated metric based on population or sub-group may not capture individual variations. This study implicates the motivation to explore tissue composition variations within the indentation sites as well as the potential importance to include variations in surface stiffness during surgical simulations.     

Real-time subject-specific monitoring of internal deformations and stresses in the soft tissues of the foot: a new approach in gait analysis

No technology is presently available to provide real-time information on internal deformations and stresses in plantar soft tissues of individuals during evaluation of the gait pattern. Because internal deformations and stresses in the plantar pad are critical factors in foot injuries such as diabetic foot ulceration, this severely limits evaluation of patients. To allow such real-time subject-specific analysis, we developed a hierarchal modeling system which integrates a two-dimensional gross structural model of the foot (high-order model) with local finite element (FE) models of the plantar tissue padding the calcaneus and medial metatarsal heads (low-order models). The high-order whole-foot model provides real-time analytical evaluations of the time-dependent plantar fascia tensile forces during the stance phase. These force evaluations are transferred, together with foot-shoe local reaction forces, also measured in real time (under the calcaneus, medial metatarsals and hallux), to the low-order FE models of the plantar pad, where they serve as boundary conditions for analyses of local deformations and stresses in the plantar pad. After careful verification of our custom-made FE solver and of our foot model system with respect to previous literature and against experimental results from a synthetic foot phantom, we conducted human studies in which plantar tissue loading was evaluated in real time during treadmill gait in healthy individuals (N = 4). We concluded that internal deformations and stresses in the plantar pad during gait cannot be predicted from merely measuring the foot-shoe force reactions. Internal loading of the plantar pad is constituted by a complex interaction between the anatomical structure and mechanical behavior of the foot skeleton and soft tissues, the body characteristics, the gait pattern and footwear. Real-time FE monitoring of internal deformations and stresses in the plantar pad is therefore required to identify elevated deformation/stress exposures toward utilizing it in gait laboratories to protect feet that are susceptible to injury.     

The compressive mechanical properties of diabetic and non-diabetic plantar soft tissue

Diabetic subjects are at an increased risk of developing plantar ulcers. Knowledge of the physiologic compressive properties of the plantar soft tissue is critical to understanding the possible mechanisms of ulcer formation and improving treatment options. The purpose of this study was to determine the compressive mechanical properties of the plantar soft tissue in both diabetic and non-diabetic specimens from six relevant locations beneath the foot, namely the hallux (big toe), first, third, and fifth metatarsal heads, lateral midfoot, and calcaneus (heel). Cylindrical specimens (1.905 cm diameter) from these locations were excised and separated from the skin and bone from 4 diabetic and 4 non-diabetic age-matched, elderly, fresh-frozen cadaveric feet. Specimens were then subjected to biomechanically realistic strains of ～50% in compression using triangle wave tests conducted at five frequencies ranging from 1 to 10 Hz to determine tissue modulus, energy loss, and strain rate dependence. Diabetic vs. non-diabetic results across all specimens, locations, and testing frequencies demonstrated altered mechanical properties with significantly increased modulus (1146.7 vs. 593.0 kPa) but no change in energy loss (68.5 vs. 67.9%). All tissue demonstrated strain rate dependence and tissue beneath the calcaneus was found to have decreased modulus and energy loss compared to other areas. The results of this study could be used to generate material properties for all areas of the plantar soft tissue in diabetic or non-diabetic feet, with implications for foot computational modeling efforts and potentially for pressure alleviating footwear that could reduce plantar ulcer incidence.     

Cultivation of the first mesophilic representative ("mesotoga") within the order Thermotogales

Cultivated members of the order Thermotogales comprise only thermophilic to hyperthermophilic anaerobic microorganisms. However, based on molecular studies, the existence of mesophilic members (“mesotoga”) within this order has been postulated but has not been demonstrated by cultural approaches so far. A “mesotoga” (strain PhosAc3) that belonged to an uncultivated lineage distantly related to the thermophilic Kosmotoga genus has now been cultivated in axenic culture. It grew between 30 °C and 50 °C (optimum 40 °C) and oxidized lactate using elemental sulphur as a terminal electron acceptor. Further genomic and physiological characterization of strain PhosAc3 will be important not only for understanding bacterial adaptation to high and moderate temperatures at small evolutionary scales, but also because “mesotoga” might play a crucial ecological role in ecosystems polluted by aromatic compounds.     

Relation between the ankle joint angle and the maximum isometric force of the toe flexor muscles

The purpose of this study was to investigate the relationships between the ankle joint angle and maximum isometric force of the toe flexor muscles. Toe flexor strength and electromyography activity of the foot muscles were measured in 12 healthy men at 6 different ankle joint angles with the knee joint at 90 deg in the sitting position. To measure the maximum isometric force of the toe flexor muscles, subjects exerted maximum force on a toe grip dynamometer while the activity levels of the intrinsic and extrinsic plantar muscles were measured. The relation between ankle joint angle and maximum isometric force of the toe flexor muscles was determined, and the isometric force exhibited a peak when the ankle joint was at 70–90 deg on average. From this optimal neutral position, the isometric force gradually decreased and reached its nadir in the plantar flexion position (i.e., 120 deg). The EMG activity of the abductor hallucis (intrinsic plantar muscle) and peroneus longus (extrinsic plantar muscle) did not differ at any ankle joint angles. The results of this study suggest that the force generation of toe flexor muscles is regulated at the ankle joint and that changes in the length-tension relations of the extrinsic plantar muscle could be a reason for the force-generating capacity at the metatarsophalangeal joint when the ankle joint angle is changed.     

Characterisation of physiological and immunological differences between Pacific oysters (Crassostrea gigas) genetically selected for high or low survival to summer mortalities and fed different rations under controlled conditions

Within the framework of a national scientific program named “MORtalités ESTivales de l'huître creuse Crassostrea gigas” (MOREST), a family-based experiment was developed to study the genetic basis of resistance to summer mortality in the Pacific oyster, Crassostrea gigas. As part of the MOREST project, the second generation of three resistant families and two susceptible families were chosen and pooled into two respective groups: “R” and “S”. These two groups of oysters were conditioned for 6 months on two food levels (4% and 12% of oyster soft-tissue dry weight in algal dry weight per day) with a temperature gradient that mimicked the Marennes-Oléron natural cycle during the oyster reproductive period. Oyster mortality remained low for the first two months, but then rapidly increased in July when seawater temperature reached 19 °C and above. Mortality was higher in “S” oysters than in “R” oysters, and also higher in oysters fed the 12% diet than those fed 4%, resulting in a decreasing, relative order in cumulative mortality as follows; 12% “S” > 12% “R” > 4% “S” > 4% “R”. Although the observed mortality rates were lower than those previously observed in the field, the mortality differential between “R” and “S” oysters was similar. Gonadal development, estimated by tissue lipid content, followed a relative order yielding a direct, positive relationship between reproductive effort and mortality as we reported precedently by quantitative histology. Regarding hemocyte parameters, one of the most striking observations was that reactive oxygen species (ROS) production was significantly higher in “S” oysters than in “R” oysters in May and June, regardless of food level. The absence of known environmental stress under these experimental conditions suggests that the ROS increase in “S” oyster could be related to their higher reproductive activity. Finally, a higher increase in hyalinocyte counts was observed for”S” oysters, compared to “R” oysters, in July, just before mortality. Taken together, our results suggest an association of genetically based resistance to summer mortality, reproductive strategy and hemocyte parameters.     

Cerebral perfusion pressure in giraffe: modelling the effects of head-raising and -lowering

Loss of consciousness caused by positional changes of the head results from reduced cerebral blood flow (CBF). CBF is related to cerebral perfusion pressure (CPP). CPP is the difference between mean arterial pressure (MAP) at the head and intracranial pressure (ICP). The positional change of the giraffe head between ground level and standing upright is the largest of all animals yet loss of consciousness does not occur. We have investigated the possibility that an increase in CPP protects giraffe from fainting, using a mechanical model that functioned as an anatomical U-tube. It consisted of a rigid ascending “carotid” limb, a collapsible “brain” tube drained by a rigid, “vertebral venous plexus” (VVP) tube, and a collapsible “head” tube drained by a collapsible tube representing the “jugular vein”. The descending tubes could be rotated relative to the “carotid” tube to be horizontal, or at 30°, 45°, and 60° to the vertical to simulate changes in head position. Pressure at the top of the “carotid” tube was intracranial MAP, at the top of the “VVP” tube was ICP, and the difference CPP. In the simulated “head-up” position and a fluid flow rate of 4 L min⁻¹, CPP was ∼170 mmHg. With the VVP tube horizontal, CPP fell from ∼170 to 45 mmHg, but increased to ∼67 mmHg at 30° “down”, to ∼70 mmHg at 45° “down” and to ∼75 at 60° “down”. The fall in CPP in the head-down positions resulted from a decrease in viscous resistance in, and dissipation of pressure to, the “head” and “jugular” tubes. These data provide an estimate of cranial pressure changes in giraffe during positional changes of the head, and suggest that an increase in CPP plays a significant role in maintaining CBF during head-raising and that it may be an important mechanism for preventing fainting in giraffe.     

Stability analysis of gliding flight of a swallowtail butterfly Papilio xuthus

Preliminary observation of the flights of swallowtail butterfly Papilio xuthus revealed that its dihedral angle is larger than 30° and that the section of its left hind wing close to its body and the counterpart of its right hind wing actually clap and form a “vertical tail”. In this study, the effects of these two features on the lateral-directional dynamic flight stability of these butterflies were analyzed theoretically and revealed the following: (a) when the dihedral angle is larger than 30°, the lateral-directional motion of the swallowtail becomes stable; (b) the vertical tail stabilizes the dutch roll mode; (c) the effects of the dihedral angle on the roll and spiral modes of a swallowtail are qualitatively the same as those of a meter-sized airplane; and (d) with increasing dihedral angle, the stability of the dutch roll mode decreases for a meter-sized airplane with vertical and horizontal tails but increases for the swallowtail. A possible explanation for the latter effect is the smaller Reynolds number of the insect that causes the drag coefficient of the swallowtail wings to increase more rapidly with an increasing angle of attack compared to a large airplane.     

Effects of different storage protocols on cat testis tissue potential for xenografting and recovery of spermatogenesis

The loss of genetic diversity due to premature death of valuable individuals is a significant problem in animal conservation programs, including endangered felids. Testis tissue xenografting has emerged as a system to obtain spermatozoa from dead immature animals, however protocols to store this tissue before xenografting are still lacking. This study focused on testis tissue cryopreservation and storage from the domestic cat (Felis catus) classified as “pre-pubertal” and “pubertal” according to spermatogenesis development. Grafts from testis tissue cryopreserved with DMSO 1.4M, recovered after 10 weeks xenografting, presented seminiferous tubules with no germ cells. On the contrary, testis tissue from pre-pubertal animals preserved in ice-cold medium for 2 to 5 days presented no loss of viability or spermatogenic potential, while the number of grafts of pubertal cat testis tissue with germ cells after 10 weeks of xenografting decreased with increasing storage time. Nevertheless, even grafts from pre-pubertal cat testis tissue presented lower anti-DDX4 and anti-BOULE staining (proteins necessary for the meiosis completion), when compared with adult cat testis. Finally, a strong correlation found between testis weight and xenograft outcome may help choose good candidates for xenografting.     

Impact responses of the flexed human knee using a deformable impact interface

Blunt impact trauma to the patellofemoral joint during car accidents, sporting activities, and falls can produce a range of injuries to the knee joint, including gross bone fracture, soft tissue injury, and/or microinjuries to bone and soft tissue. Currently, the only well-established knee injury criterion applies to knee impacts suffered during car accidents. This criterion is based solely on the peak impact load delivered to seated cadavers having a single knee flexion angle. More recent studies, however, suggest that the injury potential, its location, and the characteristics of the damage are also a function of knee flexion angle and the stiffness of the impacting structure. For example, at low flexion angles, fractures of the distal patella are common with a rigid impact interface, while at high flexion angles splitting of the femoral condyles is more evident. Low stiffness impact surfaces have been previously shown to distribute impact loads over the anterior surface of the patella to help mitigate gross and microscopic injuries in the 90 deg flexed knee. The objective of the current study was to determine if a deformable impact interface would just as effectively mitigate gross and microscopic injuries to the knee at various flexion angles. Paired experiments were conducted on contralateral knees of 18 human cadavers at three flexion angles (60, 90, 120 deg). One knee was subjected to a fracture level impact experiment with a rigid impactor, and the opposite knee was impacted with a deformable interface (3.3 MPa crush strength honeycomb material) to the same load. This (deformable) impact interface was effective at mitigating gross bone fractures at approximately 5 kN at all flexion angles, but the frequency of split fracture of the femoral condyles may not have been significantly reduced at 120 deg flexion. On the other hand, this deformable interface was not effective in mitigating microscopic injuries observed for all knee flexion angles. These new data, in concert with the existing literature, suggest the chosen impact interface was not optimal for knee injury protection in that fracture and other minor injuries were still produced. For example, in 18 cadavers a total of 20 gross fractures and 20 subfracture injuries were produced with a rigid interface and 5 gross fractures and 21 subfracture injuries with the deformable interface selected for the current study. Additional studies will be needed to optimize the knee impact interface for protection against gross and microscopic injuries to the knee.