Membrane adsorbers for selective removal of bacterial endotoxin

Surface-modified flat-sheet microfiltration membranes were functionalised with poly-l-lysine, polymyxin B, poly(ethyleneimine), l-histidine, histamine, α-amylase and DEAE as well as deoxycholate. Their suitability to remove endotoxin from both buffers and protein solutions was examined using bovine serum albumin, murine IgG₁ and lysozyme as model proteins. In protein-free solutions reduction from 6000 EU/ml to <0.1 EU/ml was achieved with all applied ligands; only α-amylase as well as l-histidine and histamine, when immobilized via the non-ionic spacer bisoxirane, exhibited low clearance factors at neutral pH. The adsorption of endotoxin is mainly ruled by electrostatic interaction forces. Thus in multi-component systems, such as endotoxin-contaminated protein solutions, competing interactions take place: acidic proteins compete with endotoxin for binding sites at the membrane adsorbers, basic proteins compete with the ligands for endotoxin and act as endotoxin carriers. With properly chosen conditions the membrane adsorbers presented here show exceptional effectiveness also in the presence of proteins. They are generally superior to functionalised Sepharose chromatographic sorbents and allow fast processing. They may contribute to reduce the risks in the application of parenterals and diagnostics.     

Aqueous two-phase systems with a liquid protein (bovine serum albumin) phase for partitioning of enzymes

New aqueous liquid-liquid two-phase systems based on bovine serum albumin and sodium thiocyanate in combination with either poly(vinyl alcohol) or poly(ethylene glycol) were investigated. Phase diagrams are presented. Lactate dehydrogenase and some mitochondrial enzymes were partitioned in the systems. All the phase components used influenced, either positively or negatively, the activity of lactate dehydrogenase. The enzymes showed a strong preference for the albumin phase. Possible scientific and biotechnological uses are discussed.     

Continuous separation of proteins by poly(vinyl alcohol) shielded Multichannel Flow Electrophoresis

Summary A hydrophilic polysulphone membrane spaced multicompartment electrolyzer for Multichannel Flow Electrophoresis (MFE) was developed. Application of poly(vinyl alcohol) (PVA) in MFE resulted in a 35% increase of protein transmembrane flux. Continuous separation of bovine serum albumin (BSA) and haemoglobin bovine blood (HBB) model mixture by PVA shielded MFE yielded 56mg BSA and 48mg HBB per hour. The average recovery was 65%.     

Adsorptive membranes for bilirubin removal

In this study, we employed ethylene vinyl alcohol (EVAL) adsorptive membranes with bovine serum albumin (BSA) as bioligand for affinity supports for bilirubin (BR) retention. Microfiltration membranes were prepared from ternary or quaternary water/(1-octanol)/DMSO/EVAL systems. To obtain active binding sites for BSA, the EVAL membranes were either chemically functionalized in aqueous and organic medium and by plasma dischargement or physically activated by entrapping of active particles. Static BR removal was determined for all EVAL-BSA membranes. BR retentions relevant for human plasma were gained for the mixed adsorber membranes and additionally investigated in the dynamic mode.     

Electric Field-Controlled Benzoic Acid and Sulphanilamide Delivery from Poly(Vinyl Alcohol) Hydrogel

The controlled release of benzoic acid (3.31 Å) and sulphanilamide (3.47 Å) from poly(vinyl alcohol), PVA, hydrogels fabricated by solution casting at various cross-linking ratios, were investigated. The PVA hydrogels were characterized in terms of the degree of swelling, the molecular weight between cross-links, and the mesh size. The drug release experiment was carried out using a modified Franz diffusion cell, at a pH value of 5.5 and at temperature of 37°C. The amount of drug release and the diffusion coefficients of the drugs from the PVA hydrogels increased with decreasing cross-linking ratio, as a larger mesh size was obtained with lower cross-linking ratios. With the application of an electric field, the amount of drug release and the diffusion coefficient increased monotonically with increasing electric field strength, since the resultant electrostatic force drove the ionic drugs from the PVA matrix. The drug size, matrix pore size, electrode polarity, and applied electric field were shown to be influential controlling factors for the drug release rate.KEY WORDS: electrophoresis force, ionic drug delivery, iontophoresis, poly(vinyl alcohol)     

Rheological characterisation of a novel thermosensitive chitosan/poly(vinyl alcohol) blend hydrogel

Thermosensitive hydrogels that are triggered by changes in environmental temperature thus resulting in in situ hydrogel formation have recently attracted the attention of many investigators for biomedical applications. In the current work, the thermosensitive hydrogel was prepared through the mixture of chitosan (CS), poly(vinyl alcohol) (PVA) and sodium bicarbonate. The mixture was liquid aqueous solutions at low temperature (about 4 °C), but a gel under physiological conditions. The hydrogel was characterized by FTIR, swelling and rheological analysis. The effect of hydrogel composition and temperature on both the gel process and the gel strength was investigated from which possible hydrogel formation mechanisms were inferred. In addition, the hydrogel interior morphology as well as porosity of structure was evaluated by scanning electron microscopy (SEM). The potential of the hydrogels as vehicles for delivering bovine serum albumin (BSA) were also examined. In this study, the physically crosslinked chitosan/PVA gel was prepared under mild conditions without organic solvent, high temperature or harsh pH. The viscoelastic properties, as investigated rheologically, indicate that the gel had good mechanical strength. The gel formed implants in situ in response to temperature change, from low temperature (about 4 °C) to body temperature, which was very suitable for local and sustained delivery of proteins, cell encapsulation and tissue engineering.     

Preparation and evaluation of polyvinyl alcohol-co-oleylvinyl ether derivatives as tumor-specific cytotoxic systems

A series of poly(vinyl alcohol) amphiphilic derivatives have been prepared to obtain polymeric aggregates in aqueous phase holding thermodynamic instability. The aim was to evaluate their ability to interact with tumor cells eliciting selective cytotoxicity. The poly(vinyl alcohol) derivatives were prepared by partial substitution of poly(vinyl alcohol) (MW 10 kDa) with both oleyl chains and poly(ethylene glycol) monoethyl ethers (PEGMEE) of different molecular weights. The substitution degree was 1.5% for the oleyl chains and 1% for the PEGMEE chains (moles of substituent per 100 mol of hydroxyvinyl monomer). The polyvinyl derivatives obtained easily dissolved in water. Dynamic and static light scattering measurements on the polymer aqueous solutions indicated the formation of polymeric aggregates characterized by low polydispersity (0.232-0.299) and mean size (218-382 nm) in the range suitable for intravenous administration. Moreover, they were characterized by different packing densities and thermodynamic instabilities driving the polymers to interact with hydrophobic membranes. Among the analyzed polymers, the poly(vinyl alcohol)-co-oleylvinyl ether substituted with triethylene glycol monoethyl ether (P10(4)) provided in solution the highest affinity for hydrophobic membranes. P10(4), moreover, was the most cytotoxic toward the tumor cell lines analyzed (neuroblastoma: SH-SY5Y, IMR-32, HTLA-230. melanoma: MZ2-MEL, RPMI7932.), while it did not appreciably alter the viability of the normal resting lymphocytes. The peculiar behavior of the P10(4) aggregates has been correlated to their high thermodynamic instability in solution due to the high packing density that triggers the polymeric aggregates to interact with hydrophobic membranes such as the tumor cell membranes, thus eliciting cytotoxicity.     

Multiwalled carbon nanotubes-ceramic electrode modified with substrate-selective imprinted polymer for ultra-trace detection of bovine serum albumin

This study describes the synthesis of a new class of substrate-selective molecularly imprinted polymer. This involved tetraethylene glycol 3-morpholin propionate acrylate (functional monomer) and bovine serum albumin (template) for polymerization in aqueous condition, using "surface grafting-from" approach directly on a vinyl exposed multiwalled carbon nanotubes-ceramic electrode. The analyte recapture at pH 6.8 in aqueous environment simultaneously involved hydrophobically driven hydrogen bonds and ionic interactions between negatively charged bovine serum albumin and positively charged imprinted nanofilm. The selectively encapsulated bovine serum albumin first gets reduced at -0.9V and then oxidized within the cavity, without getting stripped off, to respond a differential pulse voltammetry signal. The limit of detection [0.42ngmL(-1) (3σ, RSD≤1.02%)] obtained was free from any cross-reactivity and matrix complications in aqueous, pharmaceutical, serum, and liquid milk samples. The proposed sensor can be used as a practical sensor for ultra-trace analysis of bovine serum albumin in clinical settings.     

Fractionation of β‐Lactoglobulin from whey by mixed matrix membrane ion exchange chromatography

Mixed matrix membranes (MMMs), which incorporate adsorptive particles during membrane casting, can be prepared simply and have performances that are competitive with other membrane chromatography materials. The application of MMM chromatography for fractionation of β‐Lactoglobulin from bovine whey is described in this article. MMM chromatography was prepared using ethylene vinyl alcohol polymer and lewatit anion exchange resin to form a flat sheet membrane. The membrane was characterized in terms of structure and its static and dynamic binding capacities were measured. The optimum binding for β‐Lactoglobulin was found to be at pH 6.0 using 20 mM sodium phosphate buffer. The MMM had a static binding capacity of 120 mg/g membrane (36 mg/mL membrane) and 90 mg/g membrane (27 mg/mL membrane) for β‐Lactoglobulin and α‐Lactalbumin, respectively. In batch fractionation of whey, the MMM showed selective binding towards β‐Lactoglobulin compared to other proteins. The dynamic binding capacity of β‐Lactoglobulin in whey solution was about 80 mg/g membrane (24 mg β‐Lac/mL of MMM), which is promising for whey fractionation using this technology. This is the first reported application of MMM chromatography to a dairy feed stream. Biotechnol. Bioeng. 2009;103: 138–147. © 2008 Wiley Periodicals, Inc.     

Optimization of the Endotoxin Removal Performance of Solid-Phase Conjugated S3E3 Antimicrobial Peptide Using Response Surface Methodology

S3E3 is a new variant of S3 antimicrobial peptide (AMP) derived from factor C of horseshoe hemolymph and features a high binding affinity for endotoxin. In this research, site-specific conjugated S3E3 AMP onto Sepharose 6% solid phase support (S3E3-S-Sepharose) was applied for endotoxin removal from protein solutions. The bovine serum albumin (BSA) was chosen as a protein model due to its acidic-sticky nature interfering with the endotoxin removal process. The batch process parameters including, endotoxin concentration, pH, and ionic strength of the sample were optimized by response surface methodology to reach maximum endotoxin binding capacity and protein recovery. The predicted optimal conditions for enhanced endotoxin removal performance were as follows: pH 4.5, 25 mM NaCl, and 68,500 EU/ml endotoxin leading to a maximum endotoxin binding capacity of 3.114?×?10⁺⁶ EU/ml of resin and a 95.89% protein recovery. S3E3-S-Sepharose could be applied as an efficient endotoxin removal affinity chromatography matrix at downstream processes of recombinant therapeutics due to its high capacity and protein recovery.

     

Virus filtration of high‐concentration monoclonal antibody solutions

The ability to process high‐concentration monoclonal antibody solutions (> 10 g/L) through small‐pore membranes typically used for virus removal can improve current antibody purification processes by eliminating the need for feed stream dilution, and by reducing filter area, cycle‐time, and costs. In this work, we present the screening of virus filters of varying configurations and materials of construction using MAb solutions with a concentration range of 4–20 g/L. For our MAbs of interest—two different humanized IgG1s—flux decay was not observed up to a filter loading of 200 L/m² with a regenerated cellulose hollow fiber virus removal filter. In contrast, PVDF and PES flat sheet disc membranes were plugged by solutions of these same MAbs with concentrations >4 g/L well before 50 L/m². These results were obtained with purified feed streams containing <2% aggregates, as measured by size exclusion chromatography, where the majority of the aggregate likely was composed of dimers. Differences in filtration flux performance between the two MAbs under similar operating conditions indicate the sensitivity of the system to small differences in protein structure, presumably due to the impact of these differences on nonspecific interactions between the protein and the membrane; these differences cannot be anticipated based on protein pI alone. Virus clearance data with two model viruses (XMuLV and MMV) confirm the ability of hollow fiber membranes with 19 ± 2 nm pore size to achieve at least 3–4 LRV, independent of MAb concentration, over the range examined. © 2009 American Institute of Chemical Engineers Biotechnol. Prog., 2009     

Poly(vinyl alcohol) nanofibers by electrospinning as a protein delivery system and the retardation of enzyme release by additional polymer coatings

Protein-loaded (bovine serum albumin (BSA) or luciferase) poly(vinyl alcohol) (PVA) nanofibers were obtained by electrospinning. Poly(p-xylylene) (PPX, also coined as parylene) coated PVA/BSA nanofibers were prepared by chemical vapor deposition (CVD). The release of BSA from PVA nanofibers under physiological conditions was monitored by absorption spectroscopy. Burst release of BSA was noted with uncoated PVA nanofibers. In contrast, PPX-coated nanofibers exhibited a significantly retarded release of BSA depending on the coating thickness of PPX (ranging from 40 to 300 nm). Luciferase was used here as model enzyme, which after electrospinning retained its enzyme activity. This preservation of enzyme activity and the continuous release of the intact enzyme from the immersed fibers meets a fundamental prerequisite for the application of enzymes or other sensitive agents released from electrospun nanofibers under physiological conditions.     

Three-Dimensionally Printed Microfluidic Cross-flow System for Ultrafiltration/Nanofiltration Membrane Performance Testing

Minimization and management of membrane fouling is a formidable challenge in diverse industrial processes and other practices that utilize membrane technology. Understanding the fouling process could lead to optimization and higher efficiency of membrane based filtration. Here we show the design and fabrication of an automated three-dimensionally (3-D) printed microfluidic cross-flow filtration system that can test up to 4 membranes in parallel. The microfluidic cells were printed using multi-material photopolymer 3-D printing technology, which used a transparent hard polymer for the microfluidic cell body and incorporated a thin rubber-like polymer layer, which prevents leakages during operation. The performance of ultrafiltration (UF), and nanofiltration (NF) membranes were tested and membrane fouling could be observed with a model foulant bovine serum albumin (BSA). Feed solutions containing BSA showed flux decline of the membrane. This protocol may be extended to measure fouling or biofouling with many other organic, inorganic or microbial containing solutions. The microfluidic design is especially advantageous for testing materials that are costly or only available in small quantities, for example polysaccharides, proteins, or lipids due to the small surface area of the membrane being tested. This modular system may also be easily expanded for high throughput testing of membranes.      

Non-mulberry silk sericin/poly (vinyl alcohol) hydrogel matrices for potential biotechnological applications

This study reports a novel biopolymeric matrix fabricated by chemically cross-linking poly (vinyl alcohol) with silk sericin protein obtained from cocoons of the tropical tasar silkworm Antheraea mylitta. Glutaraldehyde was used as a cross-linking agent with hydrochloric acid acting as an initiator. The matrices were biophysically characterized and the cytocompatibility of the matrices was evaluated for their suitability as biomaterials. The surface morphology was assessed using atomic force microscopy while the changes taking place after cross-linking were confirmed by Fourier transform infrared spectroscopy. The enhanced thermal stability of the constructs was assessed by thermogravimetric and differential scanning calorimetry. Fourier transform infrared spectroscopy analysis showed that sericin was chemically cross-linked with poly (vinyl alcohol) using glutaraldehyde. Silk sericin protein demonstrated a favorable effect on animal cell culture by successfully improving the adhering and spreading of cells on the poorly adhering surface of poly (vinyl alcohol). Confocal microscopy revealed cell spreading and actin filament development in sericin/poly (vinyl alcohol) hydrogel matrices. These findings prove the potential of non-mulberry silk sericin/poly (vinyl alcohol) hydrogel matrices to be used as biocompatible and biopolymeric material for tissue-engineering and biotechnological applications.     

Mercaptoheterocyclic ligands grafted on a poly(ethylene vinyl alcohol) membrane for the purification of immunoglobulin G in a salt independent thiophilic chromatography

In this study, we attempted a limited combinatorial approach for designing affinity ligands based on mercaptoheterocyclic components. The template, divinyl sulfone structure (DVS), which was grafted on poly(ethylene vinyl alcohol) (PEVA) hollow fiber membrane, has served for the tethering of different heterocyclic compounds as pyridine, imidazole, purine and pyrimidine rings. Their ability to adsorb specifically IgG in a salt independent manner out of pure IgG solution, mixture of IgG/albumin and human plasma was demonstrated. Mercapto methyl imidazole (MMI) has shown the best adsorption of IgG in terms of binding capacity. No subclass discrimination was observed on all tested ligands except for mercapto methyl pyrimidine where the major IgG subclass adsorbed was IgG3. MMI gave an IgG binding capacity of 100 microg/cm2 of hollow fiber membrane surface area.     

Poly(lactic-co-glycolic acid) hollow fibre membranes for use as a tissue engineering scaffold

Mass transfer limitations of scaffolds are currently hindering the development of 3-dimensional, clinically viable, tissue engineered constructs. We have developed a poly(lactide-co-glycolide) (PLGA) hollow fibre membrane scaffold that will provide support for cell culture, allow psuedovascularisation in vitro and provide channels for angiogenesis in vivo. We produced P(DL)LGA flat sheet membranes using 1, 4-dioxane and 1-methyl-2-pyrrolidinone (NMP) as solvents and water as the nonsolvent, and hollow fibre membranes, using NMP and water, by dry/wet- and wet-spinning. The resulting fibres had an outer diameter of 700 micro m and an inner diameter of 250 micro m with 0.2-1.0 micro m pores on the culture surface. It was shown that varying the air gap and temperature when spinning changed the morphology of the fibres. The introduction of a 50 mm air gap caused a dense skin of 5 micro m thick to form, compared to a skin of 0.5 micro m thick without an air gap. Spinning at 40 degrees C produced fibres with a more open central section in the wall that contained more, larger macrovoids compared to fibres spun at 20 degrees C. Culture of the immortalised osteogenic cell line 560pZIPv.neo (pZIP) was carried out on the P(DL)LGA flat sheets in static culture and in a P(DL)LGA hollow fibre bioreactor under counter-current flow conditions. Attachment and proliferation was statistically similar to tissue culture polystyrene on the flat sheets and was also successful in the hollow fibre bioreactor. The P(DL)LGA hollow fibres are a promising scaffold to address the size limitations currently seen in tissue engineered constructs.     

Endotoxin removal by anion-exchange polymeric matrix.

The effects of anion-exchange polymeric matrices on endotoxin removal from albumin and gamma-globulin solutions are evaluated. The positively charged cellulose acrylic media carrying DEAE or QAE functional groups remove significant amounts of endotoxin from tap water, but are less effective in protein solutions. With properly controlled pH levels and salt concentrations, the endotoxin level in a protein solution can be reduced; however, low endotoxin concentrations, less than 100 pg/ml, are more difficult to remove. The endotoxin removal capacity depends on the number of functional groups existing in the matrix, expressed as the number of milliequivalents (meq), and on the pH operable range, which is directly related to the pK alpha value of the matrix. The effects of pH and salt on endotoxin removal from albumin and gamma-globulin solutions by an anion-exchange polymeric matrix were evaluated statically in test tubes. In addition, a dynamic flow was performed under statically defined conditions on a 250-ml DEAE cartridge for the removal of endotoxin from albumin at a flow rate of 40 ml/min. A greater than 75% reduction in the endotoxin can be achieved, with protein loss occurring only in the early stage of removal. Such processes are useful for the reduction of endotoxin from biological solutions produced by natural sources or recombinant DNA technology.     

Electrospun core-shell nanofibers from homogeneous solution of poly(vinyl alcohol)/bovine serum albumin

We report on the preparation and characterization of core-shell structure of bovine serum albumin (BSA) blended poly(vinyl alcohol) (PVA) composite nanofibers by using electrospinning process. The core-shell structure nanofibers have been electrospun from the homogeneous solution of BSA (as shell) and PVA (as core). The morphology, chemical compositions, structure and thermal properties of the resultant products were characterized by scanning electron microscopy (SEM), energy dispersive X-ray spectrometer (EDX), high-resolution transmission electron microscopy (HR-TEM), Fourier transform infrared (FT-IR) spectroscopy, differential scanning calorimetry, thermogravimetric analysis (TGA) and X-ray photoelectron spectroscopy (XPS) techniques. The blending ratio of PVA and BSA, molecular weight of BSA and the applied voltage of electrospinning process were observed to be the key influence factors on the formation of core-shell nanofibers structure. Based on the experimental findings, we proposed a possible physical mechanism for the formation of core-shell nanofibers structure of PVA blended BSA composite.     

Bubble Contact Angle Method for Evaluating Substratum Interfacial Characteristics and Its Relevance to Bacterial Attachment

A bubble contact angle method was used to determine interfacial free-energy characteristics of polystyrene substrata in the presence and absence of potential surface-conditioning proteins (bovine glycoprotein, bovine serum albumin, fatty acid-free bovine serum albumin), a bacterial culture supernatant, and a bacterial exopolymer. Clean petri dish substrata gave a contact angle of 90°, but tissue culture dish substrata were more hydrophilic, giving an angle of 29° or less. Bubble contact angles at the surfaces exposed to the macromolecular solutions varied with the composition and concentration of the solution. Modification by pronase enzymes of the conditioning effect of proteins depended on the nature of both the substratum and the protein, as well as the time of addition of the enzyme relative to the conditioning of the substratum. The effects of dissolved and substratum-adsorbed proteins on the attachment of Pseudomonas sp. strain NCMB 2021 to petri dishes and tissue culture dishes were consistent with changes in bubble contact angles (except when proteins were adsorbed to tissue culture dishes before attachment) as were alterations in protein-induced inhibition of bacterial attachment to petri dishes by treatment with pronase. Differences between the attachment of pseudomonads to petri dishes and tissue culture dishes suggested that different mechanisms of adhesion are involved at the surfaces of these two substrata.     

Behavior of human immunoglobulin G adsorption onto immobilized Cu(II) affinity hollow‐fiber membranes

Iminodiacetic acid (IDA) and tris(2‐aminoethyl)amine (TREN) chelating ligands were immobilized on poly(ethylene vinyl alcohol) (PEVA) hollow‐fiber membranes after activation with epichlorohydrin or butanediol diglycidyl ether (bisoxirane). The affinity membranes complexed with Cu(II) were evaluated for adsorption of human immunoglobulin G (IgG). The effects of matrix activation and buffer system on adsorption of IgG were studied. Isotherms of batch IgG adsorption onto finely cut membranes showed that neither of the chelates, IDA‐Cu(II) or TREN‐Cu(II), had a Langmuirean behavior with negative cooperativity for IgG binding. A comparison of equilibrium and dynamic maximum capacities showed that the dynamic capacity for a mini‐cartridge in a cross‐flow filtration mode (52.5 and 298.4 mg g^?1 dry weight for PEVA‐TREN‐Cu(II) and PEVA‐IDA‐Cu(II), respectively) was somewhat higher than the equilibrium capacity (9.2 and 73.3 mg g^?1 dry weight for PEVA‐TREN‐Cu(II) and PEVA‐IDA‐Cu(II), respectively). When mini‐cartridges were used, the dynamic adsorption capacity of IDA‐Cu(II) was the same for both mini‐cartridge and agarose gel. Copyright © 2013 John Wiley & Sons, Ltd.