Enantioseparation by ligand-exchange using particle-loaded monoliths: capillary-LC versus capillary electrochromatography

Particle-loaded monoliths containing a polymethacrylamide backbone were prepared by suspending a silica-based chiral phase in the mixture of the monomers followed by in-situ polymerization in the capillary. As chiral selector l-4-hydroxyproline chemically bonded to 3 microm silica particles was used following the separation principle of ligand-exchange. Electrolytes containing Cu(II) ions were used. Amino acid enantiomers were separated by capillary-LC and CEC, whereby the latter showed the better resolution properties. For the chiral separation of alpha-hydroxy acids the EOF was reversed by copolymerizing diallyldimethylammonium chloride instead of vinylsulfonic acid as charge providing agent. Short columns of 6 cm were found to be sufficient in the case of CEC for baseline separations of amino acids with alpha values up to 5.     

Enantioseparation of tetrahydropalmatine and Tröger's base by molecularly imprinted monolith in capillary electrochromatography

Two chiral compounds, Tröger's base and tetrahydropalmatine, were enantioseparated on the (5S, 11S)-(-)-Tröger's base and l-tetrahydropalmatine imprinted monolithic capillary columns with CEC, respectively. The monoliths were prepared by in situ thermal-initiated copolymerization of methacrylic acid (MAA) and ethylene dimethacrylate (EDMA). After optimizing the ratio of porogens (toluene and dodecanol), the obtained monolithic capillary columns show good flow-through property and enantioselectivity. The influences of CEC parameters such as pH of the buffer, organic solvent and salt concentration on the electroosmotic flow (EOF) and recognition selectivity were systematically investigated. Under the optimal conditions, baseline resolutions of two chiral compounds were achieved. In addition, the fast separation was obtained within 4 min by applying higher voltage and assisting pressure of 6 bar.     

Electrochromatographic characterization of methacrylate ester-based monolith and capillary electrochromatography separation of flavonoids

A porous polymethacrylate ester-based monolithic column for capillary electrochromatography (CEC) was designed by mean of in situ co-polymerizing lauryl methacrylate (LMA), ethylene dimethacrylate (EDMA) and 2-acrylamido-2-methyl-1-propanesulfonic acid (AMPS) in a ternary porogenic solvent including cyclohexanol, 1,4-butanediol and water. After investigating the influence factors of the CEC monolithic columns, four flavonoids (i.e., Rutin, Quercetin, Kaempferol, and Quercitrin) were separated and assayed to evaluate this monolithic column with CEC method. Under optimum conditions, the CEC method exhibited high separation efficiency, with rapid separation time of 3–4 min, for the four flavonoid samples using 10 mM phosphate buffer containing 70% acetonitrile (pH 9.0). Importantly, the proposed method could provide a promising approach for rapid separation and detection in biomedicine.     

Electrochromatographic enantioseparation of amino acids using polybutylmethacrylate-based chiral monolithic column by capillary electrochromatography

This article describes the development of a polybutylmethacrylate‐based monolithic capillary column as a chiral stationary phase. The chiral monolithic column was prepared by polymerization of butyl methacrylate (BMA), ethylene dimethacrylate (EDMA), and N‐methacryloyl‐l ‐glutamic acid (MAGA) in the presence of porogens. The porogen mixture included N,N‐dimethyl formamide and phosphate buffer. MAGA was used as a chiral selector. The effect of MAGA content was investigated on electrochromatographic enantioseparation of d,l ‐histidine, d,l ‐tyrosine, d,l ‐phenyl alanine, and d,l ‐glutamic acid. The effect of acetonitrile (ACN) content in mobile phase on electro‐osmotic flow was also investigated. It was demonstrated that the poly(BMA‐EDMA‐MAGA) monolithic chiral column can be used for the electrochromatographic enantioseparation of amino acids by capillary electrochromatography (CEC). The mobile phase was ACN/10 mM phosphate buffer (45:55%) adjusted to pH 2.7. It was observed that l ‐enantiomers of the amino acids migrated before d ‐enantiomers. The separation mechanism of electrochromatographic enantioseparation of amino acids in CEC is discussed. Chirality 24:606–609, 2012. © 2012 Wiley Periodicals, Inc.     

Separation of Folinic Acid Diastereomers in Capillary Electrophoresis Using a New Cationic β-Cyclodextrin Derivative

A method for the separation of folinic acid diastereomers by capillary electrophoresis in chiral separation media was developed. Aiming to achieve a good separation of the anionic analytes, a newly synthesized cationic β-cyclodextrin derivative, mono-6-deoxy-6-piperdine-β-cyclodextrin, was applied as the chiral selector. The effect of background electrolyte pH, the concentration of the cyclodextrin additive, and organic modifier on the separation was investigated. A good separation of folinic acid diastereomers was obtained with 30 mmol/L phosphate buffer at pH 6.50 containing 6.0 mmol/L of mono-6-deoxy-6-piperdine-β-cyclodextrin in 10% acetonitrile. Based on the capillary electrophoresis data, the binding constants of each diastereomer with mono-6-deoxy-6-piperdine-β-cyclodextrin were determined. Moreover, a computational modeling study, using the semi-empirical PM3 method, was used to discuss the possible mechanism of separation of folinic acid with mono-6-deoxy-6-piperdine-β-cyclodextrin.     

Enantioseparation of glycyl-dipeptides by CEC using particle-loaded monoliths prepared by ring-opening metathesis polymerization (ROMP)

Novel particle-loaded monolithic capillary electrochromatography (CEC) phases for chiral separations were prepared via ring-opening metathesis polymerization (ROMP) within the confines of fused silica columns with 200 microm i.d. using norborn-2-ene (NBE), 1,4,4a,5,8,8a-hexahydro-1,4,5,8,exo,endo-dimethanonaphthalene (DMN-H6) as monomers, 2-propanol and toluene as porogens, RuCl2(PCy3)2(CHPh) as initiator and silica-based particles containing the chiral selector. By suspending silica particles bearing the chiral selector in the polymerization mixture, particle-based monoliths are easily prepared. This approach has several advantages compared to particle-based separation media: (i) the concept of particle-based monoliths is broadly applicable, as any silica-based chiral phase can be used; (ii) they are inexpensive to prepare; and (iii) the manufacturing process is very simple, no sophisticated packing procedures or the preparation of end frits are required. To show the usefulness of this concept for chiral CEC, the chiral separation performance of particle-loaded CEC monoliths bearing teicoplanin aglycone, chemically bonded to 3 microm silica gel, was investigated for a set of glycyl-dipeptides. Particle-loaded ROMP CEC monoliths showed good separation performance for glycyl-dipeptides.     

Indirect synchronous fluorescence spectroscopy and direct high‐performance thin‐layer chromatographic methods for enantioseperation of zopiclone and determination of chiral‐switching eszopiclone: Evaluation of thermodynamic quantities of chromatographic separation

Economic and enantioselective synchronous fluorescence spectroscopy and high‐performance thin‐layer chromatography methods have been developed and validated as per ICH guidelines for the separation of zopiclone enantiomers using L‐(+)‐tartaric acid as a chiral selector, followed by determination of the chiral‐switching eszopiclone. Synchronous fluorescence spectroscopy was successfully applied for chiral recognition of R & S enantiomers of zopiclone at ?λ = 110 nm based on creating of diastereomeric complexes with 0.06M tartaric acid in an aqueous medium containing 0.2M disodium hydrogen orthophosphate. Synchronous fluorescence intensities of eszopiclone were recorded at 296 nm in concentration range 0.2‐ to 4‐μg/mL eszopiclone. High‐performance thin‐layer chromatography method depends on resolution of zopiclone enantiomers on achiral HPTLC silica‐gel plates using acetonitrile:methanol:water (8:2:0.25, v/v/v) containing L‐(+)‐tartaric acid as a chiral mobile‐phase additive followed by densitometric measurements at 304 nm in concentration range of 1 to 10 μg/band of eszopiclone. The effect of chiral‐selector concentration, pH, and temperature on the resolution have been studied and optimized for the proposed methods. The cited procedures were successfully applied to determine eszopiclone in commercial tablets of pure and racemic forms. Enantiomeric excess was evaluated using optical purity test and integrated peak area to describe the enantiomeric ratio. Thermodynamics of chromatographic separation, enthalpy, and entropy were evaluated using the Van't Hoff equation. The proposed methods were found to be selective for identification and determination of the eutomer in drug substances and products.     

Rapid determination of amino acids in biological samples using a monolithic silica column

A high-performance liquid chromatography method in which fluorescence detection is used for the simultaneous determination of 21 amino acids is proposed. Amino acids were derivatized with 4-fluoro-7-nitro-2,1,3-benzoxadiazole (NBD-F) and then separated on a monolithic silica column (MonoClad C18-HS, 150 mm × 3 mm i.d.). A mixture of 25 mM citrate buffer containing 25 mM sodium perchlorate (pH 5.5) and acetonitrile was used as the mobile phase. We found that the most significant factor in the separation was temperature, and a linear temperature gradient from 30 to 49°C was used to control the column temperature. The limits of detection and quantification for all amino acids ranged from 3.2 to 57.2 fmol and 10.8 to 191 fmol, respectively. The calibration curves for the NBD-amino acid had good linearity within the range of 40 fmol to 40 pmol when 6-aminocaproic acid was used as an internal standard. Using only conventional instruments, the 21 amino acids could be analyzed within 10 min. This method was found to be suitable for the quantification of the contents of amino acids in mouse plasma and adrenal gland samples.     

Liquid chromatographic direct resolution of beta-amino acids on a doubly tethered chiral stationary phase containing N--H amide linkage based on (+)-(18-crown-6)- 2,3,11,12-tetracarboxylic acid

A doubly tethered chiral stationary phase (CSP) prepared by bonding (+)-(18-crown-6)-2,3,11,12-tetracarboxylic acid to doubly tethered primary aminoalkyl silica gel was used for the resolution of various beta-amino acids. All the beta-amino acids tested were resolved quite well, the separation (alpha) and the resolution factors (RS) being in the ranges 1.34-2.09 and 2.52-7.45, respectively, with a mobile phase of methanol-water (50:50, v/v) containing 10 mM acetic acid. The chiral recognition efficiency of the doubly-tethered CSP was found to be generally superior to that of the corresponding singly-tethered CSP in the resolution of beta-amino acids. The chiral recognition behaviors for the resolution of beta-amino acids on the doubly tethered CSP were examined by varying the type and content of organic and acidic modifiers in the aqueous mobile phase and the column temperature.     

Recent progress in capillary electrophoretic analysis of amino acid enantiomers

This review highlights recent progresses in capillary electrophoresis (CE) analysis of amino acid enantiomers in the last decade. Various chiral selectors including cyclodextrins (CDs), bile salts, crown ethers, cinchona alkaloids, metal-chiral amino acid complexes, macrocyclic antibiotics and proteins have been employed to separate amino acid enantiomers. In the CE analysis of amino acids, the selection of the separation mode is one of the most important issues to obtain good resolution of target enantiomers. Among several separation modes, CD-modified capillary zone electrophoresis (CD-CZE), CD electrokinetic chromatography (CDEKC), micellar EKC (MEKC), CD-modified micellar electrokinetic chromatography (CD-MEKC), capillary electrochromatography (CEC), ligand-exchange CE (LE-CE), and nonaqueous CE (NACE) have been employed to the chiral analysis of amino acids. More than 160 published research articles collected from SciFinder Scholar databases from the year 2001 described the enantioseparations of amino acids by capillary-based electrophoresis. This review provides a comprehensive table listing the CE analysis of amino acid enantiomers with categorizing by the separation modes.     

Liquid chromatographic separation and thermodynamic investigation of lorcaserin hydrochloride enantiomers on immobilized amylose–based chiral stationary phase

A novel liquid chromatographic method was developed for enantiomeric separation of lorcaserin hydrochloride on Chiralpak IA column containing chiral stationary phase immobilized with amylose tris (3.5‐dimethylphenylcarbamate) as chiral selector. Baseline separation with resolution greater than 4 was achieved using mobile phase containing mixture of n‐hexane/ethanol/methanol/diethylamine (95:2.5:2.5:0.1, v/v/v/v) at a flow rate of 1.2 mL/min. The limit of detection and limit of quantification of the S‐enantiomer were found to be 0.45 and 1.5 μg/mL, respectively; the developed method was validated as per ICH guideline. The influence of column oven temperatures studied in the range of 20°C to 50°C on separation was studied; from this, retention, separation, and resolution were investigated. The thermodynamic parameters ΔH°, ΔS°, and ΔG° were evaluated from van't Hoff plots,(Ink′ _versus 1/T) and used to explain the strength of interaction between enantiomers and immobilized amylose–based chiral stationary phase     

Separation of amino acid enantiomers by micelle-enhanced ultrafiltration

A Micelle-enhanced ultrafiltration (MEUF) separation process was investigated that can potentially be used for large-scale enantioseparations. Copper(II)-amino acid derivatives dissolved in nonionic surfactant micelles were used as chiral selectors for the separation of dilute racemic amino acids solutions. For the alpha-amino acids phenylalanine, phenylglycine, O-methyltyrosine, isoleucine, and leucine good separation was obtained using cholesteryl L-glutamate and Cu(II) ions as chiral selector with an operational enantioselectivity (alpha(op)) up to 14.5 for phenylglycine. From a wide set of substrates, including four beta-amino acids, it was concluded that the performance of this system is determined by two factors: the hydrophobicity of the racemic amino acid, which results in a partitioning of the racemic amino acid over micelle and aqueous solution, and the stability of the diastereomeric complex formed upon binding of the amino acid with the chiral selector. The chiral hydrophobic cholesteryl anchor of the chiral selector also plays an active role in the recognition process, since inversion of the chirality of the glutamate does not yield the reciprocal enantioselectivities. However, if the cholesteryl group is replaced by a nonchiral alkyl chain, reciprocal operational enantioselectivities are found with enantiomeric glutamate selectors.     

Application of cyanuric chloride-based six new chiral derivatizing reagents having amino acids and amino acid amides as chiral auxiliaries for enantioresolution of proteinogenic amino acids by reversed-phase high-performance liquid chromatography

Six dichloro-s-triazine (DCT) reagents having l-Leu, d-Phg, l-Val, l-Met, l-Ala and l-Met-NH₂ as chiral auxiliaries in cyanuric chloride were introduced for enantioseparation of 13 proteinogenic amino acids. Four other DCTs and six monochloro-s-triazine (MCT) reagents having amino acid amides as chiral auxiliaries were also synthesized. These 16 chiral derivatizing reagents (CDRs) were used for synthesis of diastereomers of all the 13 analytes using microwave irradiation, which were resolved by reversed-phase high-performance liquid chromatography (RP-HPLC) using C18 column and gradient eluting mixture of aqueous TFA and acetonitrile with UV detection at 230 nm. It required only 60–90 s for derivatization using microwave irradiation. Better resolution and lower retention times were observed for the diastereomers prepared with CDRs having amino acids as chiral auxiliaries as compared to counterparts prepared with reagents having amino acid amides as chiral auxiliaries. As the best resolution of all the 13 analytes was observed for their diastereomers prepared using the DCT reagent having l-Leu as chiral auxiliary, this CDR was further employed for derivatization of Lys, Tyr, His and Arg followed by RP-HPLC analysis of resulting diastereomers. The results are discussed in light of acid and amide groups of chiral auxiliaries constituting CDRs, electronegativities of the atoms of achiral moieties constituting CDRs and hydrophobicities of side chains of amino acids constituting CDRs and analytes.     

Preparation and characterization of a new open‐tubular capillary column for enantioseparation by capillary electrochromatography

In order to use the enantioseparation capability of cationic cyclodextrin and to combine the advantages of capillary electrochromatography (CEC) with open‐tubular (OT) column, in this study, a new OT‐CEC, coated with cationic cyclodextrin (1‐allylimidazolium‐β‐cyclodextrin [AI‐β‐CD]) as chiral stationary phase (CSP), was prepared and applied for enantioseparation. Synthesized AI‐β‐CD was characterized by infrared (IR) spectrometry and mass spectrometry (MS). The preparation conditions for the AI‐β‐CD‐coated column were optimized with the orthogonal experiment design L₉(3⁴). The column prepared was characterized by scanning electron microscopy (SEM) and elemental analysis (EA). The results showed that the thickness of stationary phase in the inner surface of the AI‐β‐CD‐coated columns was about 0.2 to 0.5 μm. The AI‐β‐CD content in stationary phase based on the EA was approximately 2.77 mmol·m^?2. The AI‐β‐CD‐coated columns could separate all 14 chiral compounds (histidine, lysine, arginine, glutamate, aspartic acid, cysteine, serine, valine, isoleucine, phenylalanine, salbutamol, atenolol, ibuprofen, and napropamide) successfully in the study and exhibit excellent reproducibility and stability. We propose that the column, coated with AI‐β‐CD, has a great potential for enantioseparation in OT‐CEC.     

Preparation and chromatographic performance of a multifunctional immobilized chiral stationary phase based on dialdehyde microcrystalline cellulose derivatives

A novel high‐performance liquid chromatography (HPLC) multifunctional immobilized chiral stationary phase was prepared by bonding dialdehyde microcrystalline cellulose to aminosilica via Schiff base reaction and then derivatized with 3,5‐dimethylphenyl isocyanate. The HPLC multifunctional immobilized chiral stationary phase could not only achieve chiral separation but also achieve achiral separation. Chiral separation evaluation showed that 1‐(1‐naphthyl)ethanol and mandelonitrile got separation in normal phase (NP) mode. Ranolazine, benzoin ethyl ether, metalaxyl, and diclofop were successfully separated in reversed phase (RP) mode. Aromatic compounds such as polycyclic aromatic hydrocarbons (PAHs), anilines, and aromatic acids were selected as analytes to investigate the achiral separation performance of the multifunctional immobilized chiral stationary phase in NP and RP modes. The achiral separation evaluation showed that six PAHs could get good separation within 10 minutes in NP mode. Four aromatic acids were well separated in RP mode. The retention mechanism of aromatic compounds on the stationary phase was discussed, founding that π‐π interaction, π‐π electron‐donor‐acceptor (EDA) interaction, and hydrogen bonding interaction played important roles during the achiral separation process. This multifunctional immobilized chiral stationary phase had the advantages of simple bonding steps, short reaction time, and no need for space arm.     

The use of multilayered capillaries for chiral separation by electrochromatography

Fused-silica capillaries were modified by the successively multiple ionic-polymer layer (SMIL) coating technique for a capillary electrochromatography (CEC) analysis of binaphthyl enantiomers. The SMIL coating capillaries consisting of three different polymers (A(+)-B(-)-C(+) coating) were prepared by the alternative deposition of positively charged chiral or achiral polymers and negatively charged DNA. Previous studies have indicated that DNA-cationic polypeptide or synthetic polymer complexes immobilized onto the inner surface of the capillary worked as the chiral stationary phases for 1,1'-binaphthyl-2,2'-diyl hydrogen phosphate (BNP). In this study, to investigate the chiral recognition mechanism and optimize the CEC separation condition in the DNA-cationic polymer coating, effects of the chirality of the polymer unit, the strand of DNA, and the number of layer pairs on the separation were investigated. It should be noted that, since single stranded DNA (ssDNA) was more suitable to immobilize cationic polymers than double stranded DNA, the ssDNA-cationic polymer immobilized capillaries gave a stable electroosmotic flow and reproducible CEC analyses. As a result, a poly(ethyleneimine)-ssDNA-protamine (Prt) coating provided the best chiral separation of BNP. The high separation performance of the prepared capillary is discussed in terms of DNA/polycations interaction.     

Liquid chromatographic enantiomer resolution of N-hydrazide derivatives of 2-aryloxypropionic acids on a crown ether derived chiral stationary phase

The liquid chromatographic separation of the enantiomers of several N-hydrazide derivatives of 2-aryloxypropionic acids was performed on a crown ether type chiral stationary phase derived from (18-crown-6)-2,3,11,12-tetracarboxylic acid. The behavior of chromatographic parameters by the change of mobile phases and additives for the resolution of these analytes was investigated. The enantiomers of all analytes were base-line resolved with a mobile phase of 100% methanol containing 20 mM H2SO4. These results are the first reported for enantiomer resolution of chiral acids of 2-aryloxypropionic acids as their N-hydrazide derivatives.     

Chiral stationary phase covalently bound with a chiral pseudo-18-crown-6 ether for enantiomer separation of amino compounds using a normal mobile phase

In order to apply the excellent chiral recognition ability of chiral pseudo-18-crown-6 ethers that we developed to chiral separation, we prepared a chiral stationary phase (CSP) by immobilizing a chiral pseudo-18-crown-6-type host on 3-aminopropyl silica gel. A chiral column was prepared by the slurry-packing method in a stainless steel HPLC column. A liquid chromatography system using this CSP combined with the detection by mass spectrometry was used for enantiomer separation of amino compounds. A normal mobile phase can be used on this CSP as opposed to conventional dynamic coating-type CSPs. Enantiomers of 18 common natural amino acids were efficiently separated. The chiral separation observed for amino acid methyl esters, amino alcohols, and lipophilic amines was fair using this HPLC system. In view of the correlation between the enantiomer selectivity observed in chromatography and the complexion in solution, the chiral recognition in host-guest interactions might contribute to this enantiomer separation.     

Enantioseparations with cellulose tris(3-chloro-4-methylphenylcarbamate) in nano-liquid chromatography and capillary electrochromatography

Cellulose tris(3-chloro-4-methylphenylcarbamate) was coated onto native and aminopropylsilanized silica in order to prepare chiral stationary phases (CSPs) for enantioseparations using nano-liquid chromatography (nano-LC) and capillary electrochromatography (CEC). The effect of the chiral selector loading onto silica, mobile phase composition and pH, as well as separation variables on separation of enantiomers was studied. It was found that CSPs based on cellulose tris(3-chloro-4-methylphenylcarbamate) can be used for preparation of very stable capillary columns useful for enantioseparations in nano-LC and CEC in combination with polar organic mobile phases.     

Enantioseparation of racecadotril using polysaccharide‐type chiral stationary phases in polar organic mode

Enantioseparation of the antidiarrheal drug, racecadotril, was investigated by liquid chromatography using polysaccharide‐type chiral stationary phases in polar organic mode. The enantiodiscrimininating properties of 4 different chiral columns (Chiralpak AD, Chiralcel OD, Chiralpak AS, Chiralcel OJ) with 5 different solvents (methanol, ethanol, 1‐propanol, 2‐propanol, and acetonitrile) at 5 different temperatures (5–40 °C) were investigated. Apart from Chiralpak AS column the other 3 columns showed significant enantioseparation capabilities. Among the tested mobile phases, alcohol type solvents were superior over acetonitrile, and significant differences in enantioselective performance of the selector were observed depending on the type of alcohol employed. Van't Hoff analysis was used for calculation of thermodynamic parameters which revealed that enantioseparation is mainly enthalpy controlled; however, enthropic control was also observed. Enantiopure standard was used to determine the enantiomer elution order, revealing chiral selector—and mobile‐phase dependent reversal of enantiomer elution order. Using the optimized method (Chiralcel OJ stationary phase, thermostated at 10 °C, 100% methanol, flow rate: 0.6 mL/min) baseline separation of racecadotril enantiomers (resolution = 3.00 ± 0.02) was achieved, with the R‐enantiomer eluting first. The method was validated according to the ICH guidelines, and its application was tested on capsule and granules containing the racemic mixture of the drug.