Bioremediation potential of a widespread industrial biowaste as renewable and sustainable biosorbent for synthetic dye pollution

In this study, a model synthetic azo dye (Basic red 46) bioremoval by Carpinus betulus sawdust as inexpensive, eco-friendly, and sustainable biosorbent from aqueous solution was examined in a batch biosorption system. The effective environmental parameters on the biosorption process, such as the value of pH, amount of biosorbent, initial dye concentration and contact time were optimized using classical test design. The possible dye-biosorbent interaction was determined by Fourier Transform Infrared Spectroscopy (FTIR) and Scanning Electron Microscopy (SEM). The equilibrium, thermodynamic, and kinetic studies for the biosorption of Basic red 46 onto the sawdust biomass were performed. In addition, a single-stage batch dye biosorption system was also designed. The dye biosorption yield of biosorbent was significantly influenced by the change of operating variables. The experimental data were best described by the Freundlich isotherm model and both the pseudo-first-order kinetic and the pseudo-second-order kinetic models. Thermodynamic research indicated that the biosorption of dye was feasible and spontaneous. Based on the Langmuir isotherm model, the biosorbent was found to have a maximum biosorption potential higher than many other biosorbents in the literature (264.915?mg g^?1). Thus, this investigation presents a novel green option for the assessment of waste sawdust biomass as a cheap and effective biosorbent material.     

Biosorption characteristics of Aspergillus fumigatus for the decolorization of triphenylmethane dye acid violet 49

This study focuses on the possible use of Aspergillus fumigatus to remove acid violet 49 dye (AV49) from aqueous solution. In batch biosorption experiments, the highest biosorption efficiency was achieved at pH 3.0, with biosorbent dosage of 3.0 gL^?1 within about 30 min at 40 °C. The Langmuir and Freundlich models were able to describe the biosorption equilibrium of AV49 onto fungal biomass with maximum dye uptake capacity 136.98 mg g^?1. Biosorption followed a pseudo-second-order kinetic model with high correlation coefficients (R ²?>?0.99), and the biosorption rate constants increased with increasing temperature. Thermodynamic parameters indicated that the biosorption process was favorable, spontaneous, and endothermic in nature, with insignificant entropy changes. Fourier transform infrared spectroscopy strongly supported the presence of several functional groups responsible for dye–biosorbent interaction. Fungal biomass was regenerated with 0.1 M sodium hydroxide and could be reused a number of times without significant loss of biosorption activity. The effective decolorization of AV49 in simulated conditions indicated the potential use of biomass for the removal of color contaminants from wastewater.     

Date stones of Phoenix dactylifera and jujube shells of Ziziphus lotus as potential biosorbents for anionic dye removal

This study investigated the biosorption of Congo Red (CR) from aqueous solution by Date stones (DS) of Phoenix dactylifera and jujube shells (JS) of Ziziphus lotus. Batch operations were carried out in the liquid phase to observe the effect of various experimental parameters such as contact time, pH, temperature, and initial dye concentration on removal of CR. The characteristics of the DS and JS were also examined by Fourier transform infrared analysis. The biosorption data of CR on DS and JS samples were well fitted with the Langmuir isotherm and pseudo-second kinetics model with a maximum biosorption amount of 45.08 mg g^?1 for DS and 59.55 mg g^?1 for JS at pH = 4, temperature of 50°C, and an initial concentration of 100–800 mg L^?1 after 90 minutes of contact time. The outcomes indicated that DS and JS can be used as a good low-cost alternative for the treatment of effluents containing CR in water.     

Application of a novel phyco-composite biosorbent for the biotreatment of aqueous medium polluted with manganese ions

A composite phyco-biomass including four different marine macroalgae species (Chaetomorpha sp., Polysiphonia sp., Ulva sp., and Cystoseira sp.) was evaluated as a novel biosorbent for the biosorption of manganese ions from aqueous solution. The experimental studies were performed to optimize the operational factors including solution pH, biosorbent amount, initial manganese concentration, and reaction time in a batch-mode biosorption system. The removal yield of the biosorbent for manganese ions increased with increasing pH, manganese ion concentration, and reaction time, while it decreased as the biosorbent dose increased. The obtained kinetic data indicated that the removal of manganese ions by the biosorbent was best described by the pseudo-second-order model and the pore diffusion also contributed to the biosorption process. The results of isotherm and thermodynamic studies showed that the Freundlich model represented the biosorption equilibrium data well and this biotreatment system was feasible, spontaneous, and physical. The maximum manganese uptake capacity of used biosorbent was found to be 55.874 mg g^?1. Finally, a single-stage batch manganese biosorption system was designed and its kinetic performance was evaluated. All these findings revealed that the prepared composite macroalgae biosorbent has a fairly good potential for the removal of manganese ions from the aqueous medium.     

Removal of Acid Blue25 from aqueous solutions using Bengal gram fruit shell (BGFS) biomass

The feasibility for the removal of Acid Blue25 (AB25) by Bengal gram fruit shell (BGFS), an agricultural by-product, has been investigated as an alternative for high-cost adsorbents. The impact of various experimental parameters such as dose, different dye concentration, solution pH, and temperature on the removal of Acid Blue25 (AB25) has been studied under the batch mode of operation. pH is a significant impact on the sorption of AB25 onto BGFS. The maximum removal of AB25 was achieved at a pH of 2 (83.84%). The optimum dose of biosorbent was selected as 200 mg for the removal of AB25 onto BGFS. Kinetic studies reveal that equilibrium reached within 180 minutes. Biosorption kinetics has been described by Lagergren equation and biosorption isotherms by classical Langmuir and Freundlich models. Equilibrium data were found to fit well with the Langmuir and Freundlich models, and the maximum monolayer biosorption capacity was 29.41 mg g^?1 of AB25 onto BGFS. The kinetic studies indicated that the pseudo-second-order (PSO) model fitted the experimental data well. In addition, thermodynamic parameters have been calculated. The biosorption process was spontaneous and exothermic in nature with negative values of ΔG° (?1.6031 to ?0.1089 kJ mol^?1) and ΔH° (?16.7920 kJ mol^?1). The negative ΔG° indicates the feasibility of physical biosorption process. The results indicate that BGFS could be used as an eco-friendly and cost-effective biosorbent for the removal of AB25 from aqueous solution.     

Biosorption of an Azo Dye by <Emphasis Type="Italic">Aspergillus niger</Emphasis> and <Emphasis Type="Italic">Trichoderma</Emphasis> sp. Fungal Biomasses

Biosorption is an eco-friendly and cost-effective method for treating the dye house effluents. Aspergillus niger and Trichoderma sp. were cultivated in bulk and biomasses used as biosorbents for the biosorption of an azo dye Orange G. Batch biosorption studies were performed for the removal of Orange G from aqueous solutions by varying the parameters like initial aqueous phase pH, biomass dosage, and initial dye concentration. It was found that the maximum biosorption was occurred at pH 2. Experimental data were analyzed by model equations such as Langmuir and Freundlich isotherms, and it was found that both the isotherm models best fitted the adsorption data. The monolayer saturation capacity was 0.48 mg/g for Aspergillus niger and 0.45 mg/g for Trichoderma sp. biomasses. The biosorption kinetic data were tested with pseudo first-order and pseudo second-order rate equations, and it was found that the pseudo second-order model fitted the data well for both the biomasses. The rate constant for the pseudo second-order model was found to be 10–0.8 (g/mg min⁻¹) for Aspergillus niger and 8–0.4 (g/mg min⁻¹) for Trichoderma sp. by varying the initial dye concentrations from 5 to 25 mg/l. It was found that the biomass obtained from Aspergillus niger was a better biosorbent for the biosorption of Orange G dye when compared to Trichoderma sp.     

A natural macroalgae consortium for biosorption of copper from aqueous solution: Optimization,modeling and design studies

In this study, the capacity of a natural macroalgae consortium consisting of Chaetomorpha sp., Polysiphonia sp., Ulva sp. and Cystoseira sp. species for the removal of copper ions from aqueous environment was investigated at different operating conditions, such as solution pH, copper ion concentration and contact time. These environmental parameters affecting the biosorption process were optimized on the basis of batch experiments. The experimentally obtained data for the biosorption of copper ions onto the macroalgae-based biosorbent were modeled using the isotherm models of Freundlich, Langmuir, Sips and Dubinin–Radushkevich and the kinetic models of pseudo-first-order, pseudo-second-order, Elovich and Weber and Morris. The pseudo-first-order and Sips equations were the most suitable models to describe the copper biosorption from aqueous solution. The thermodynamic data revealed the feasibility, spontaneity and physical nature of biosorption process. Based on the data of Sips isotherm model, the biosorption capacity of biosorbent for copper ions was calculated as 105.370 mg g^?1 under the optimum operating conditions. A single-stage batch biosorption system was developed to predict the real-scale-based copper removal performance of biosorbent. The results of this investigation showed the potential utility of macroalgae consortium for the biosorption of copper ions from aqueous medium.     

A Novel High Biosorbent of Pb-resistant Bacterium Isolate for the Removal of Hazardous Lead from Alkaline Soil and Water: Biosorption Isotherms In Vivo and Bioremediation Strategy

A novel Pb-resistant bacterium was isolated from aged lead-contaminated alkaline soils, and was identified as Bacillus megaterium via the MIDI protocol. The biosorption isotherms and kinetics of Pb(II) associated with B. megaterium in vivo in the alkaline environment were investigated at the first time. All the batch experiments of biosorption demonstrate that the B. megaterium uptake of lead is pH-dependent, exothermic (ΔH° = ?5224.86 KJ mol^?1), spontaneous, and fits well with the Langmuir isotherm, resulting in different kinetics under different examination temperatures. The maximum biosorption capacity is 503.86 mg g^?1 at optimum conditions, which is much better in comparison to the biosorbent reported at the acidic condition in the literature. The Fourier-transform Infrared spectroscopic analysis of lead-loaded biomass confirms that the biosorption between B. megaterium and lead is the chemical adsorption in vivo. A site test indicates that B. megaterium really increases mobility and bioavailability of lead in Pb-contaminated alkaline soil in terms of chemical fractionation in vivo, which will potentially increase its uptake by hyperaccumulated plants in alkaline soils in arid or semi-arid areas of NW, China. Therefore, the novel isolate of B. megaterium with the highest adsorption capacity is a new promising biosorbent for the lead removal in alkaline water and soil.     

Modeling of Pb(II) adsorption by a fixed-bed column

Removal of Pb(II) from an aqueous environment using biosorbents is a cost-effective and environmentally benign method. The biosorption process, however, is little understood for biosorbents prepared from plant materials. In this study, the biosorption process was investigated by evaluating four adsorption models. A fixed-bed column was prepared using a biosorbent prepared from the aquatic plant Hydrilla verticillata. The effect of bed height and flow rate on the biosorption process was investigated. The objective of the study was to determine the ability of H. verticillata to biosorb Pb(II) from an aqueous environment and to understand the process, through modeling, to provide a basis to develop a practical biosorbent column. Experimental breakthrough curves for biosorption of 50 mg L^?1 aqueous Pb(II) using a fixed-bed column with 1.00 cm inner diameter were fitted to the Thomas, Adams-Bohart, Belter, and bed depth service time (BDST) models to investigate the behavior of each model according to the adsorption system and thus understand the adsorption mechanism. Model parameters were evaluated using linear and nonlinear regression methods. The biosorbent removed 65% (82.39 mg g^?1 of biosorbent) of Pb(II) from an aqueous solution of Pb(NO₃)₂ at a flow rate of 5.0 ml min^?1 in a 10 cm column. Na₂CO₃ was used to recover the adsorbed Pb(II) ions as PbCO₃ from the biosorbent. The Pb(II) was completely desorbed at a bed height of 10.0 cm and a flow rate of 5.0 ml min^?1. Fourier transform infrared (FT-IR) analysis of the native biosorbent and Pb(II)-loaded biosorbent indicated that the hydroxyl groups and carboxylic acid groups were involved in the metal bonding process. The FT-IR spectrum of Pb(II)-desorbed biosorbent showed an intermediate peak shift, indicating that Pb(II) ions were replaced by Na⁺ ions through an ion-exchange process. Of the four models tested, the Thomas and BDST models showed good agreement with experimental data. The calculated bed sorption capacity N₀ and rate constant k_a were 31.7 g L^?1 and 13.6 × 10^?4 L mg^?1 min^?1 for the C_t/C₀ value of 0.02. The BDST model can be used to estimate the column parameters to design a large-scale column.     

Biosorption of Basic Blue 7 by fungal cells immobilized on the green-type biomatrix of Phragmites australis spongy tissue

Biosorption is an effective alternative method for the control of water pollution caused by different pollutants such as synthetic dyes and metals. A new and efficient biomass system was developed from the passively immobilized fungal cells. The spongy tissue of Phragmites australis was considered as the carrier for the immobilization of Neurospora sitophila cells employed for the biosorption of Basic Blue 7. This plant tissue was used for the first time as a carrier for fungal cells. The biosorption was examined through batch- and continuous-mode operations. The biosorption process conformed well to the Langmuir model. Maximum monolayer biosorption capacity of the biosorbent was recorded as 154.756 mg g^?1. Kinetic findings showed a very good compliance with the pseudo-second-order model. The negative values of ΔG° indicated a spontaneous nature of the biosorption process and a positive value of ΔH° (14.69 kJ mol^?1) concluded favorable decolorization at high temperature. The scanning electron microscopy analysis showed that a porous, rippled, and rough surface of biomass system was covered with BB7 molecular cloud. IR results revealed that functional groups like –OH, –NH, and C?O participated to the decolorization. Breakthrough and exhausted points were found as 360 and 570 minutes, respectively. The biomass system was successfully applied to the treatment of real wastewater.     

Nickel(II) biosorption by <Emphasis Type="Italic">Rhodotorula glutinis</Emphasis>

The present study reports the feasibility of using Rhodotorula glutinis biomass as an alternative low-cost biosorbent to remove Ni(II) ions from aqueous solutions. Acetone-pretreated R. glutinis cells showed higher Ni(II) biosorption capacity than untreated cells at pH values ranging from 3 to 7.5, with an optimum pH of 7.5. The effects of other relevant environmental parameters, such as initial Ni(II) concentration, shaking contact time and temperature, on Ni(II) biosorption onto acetone-pretreated R. glutinis were evaluated. Significant enhancement of Ni(II) biosorption capacity was observed by increasing initial metal concentration and temperature. Kinetic studies showed that the kinetic data were best described by a pseudo-second-order kinetic model. Among the two-, three-, and four-parameter isotherm models tested, the Fritz-Schluender model exhibited the best fit to experimental data. Thermodynamic parameters (activation energy, and changes in activation enthalpy, activation entropy, and free energy of activation) revealed that the biosorption of Ni(II) ions onto acetone-pretreated R. glutinis biomass is an endothermic and non-spontaneous process, involving chemical sorption with weak interactions between the biosorbent and Ni(II) ions. The high sorption capacity (44.45 mg g⁻¹ at 25°C, and 63.53 mg g⁻¹ at 70°C) exhibited by acetone-pretreated R. glutinis biomass places this biosorbent among the best adsorbents currently available for removal of Ni(II) ions from aqueous effluents.     

Use of Spirulina platensis micro and nanoparticles for the removal synthetic dyes from aqueous solutions by biosorption

In this research, micro and nanoparticles of Spirulina platensis dead biomass were obtained, characterized and employed to removal FD&C red no. 40 and acid blue 9 synthetic dyes from aqueous solutions. The effects of particle size (micro and nano) and biosorbent dosage (from 50 to 750 mg) were studied. Pseudo-first order, pseudo-second order and Elovich models were used to evaluate the biosorption kinetics. The biosorption nature was verified using energy dispersive X-ray spectroscopy (EDS). The best results for both dyes were found using 250 mg of nanoparticles, in these conditions, the biosorption capacities were 295 mg g^?1 and 1450 mg g^?1, and the percentages of dye removal were 15.0 and 72.5% for the FD&C red no. 40 and acid blue 9, respectively. Pseudo-first order model was the more adequate to represent the biosorption of both dyes onto microparticles, and Elovich model was more appropriate to the biosorption onto nanoparticles. The EDS results suggested that the dyes biosorption onto microparticles occurred mainly by physical interactions, and for the nanoparticles, chemisorption was dominant.     

Evaluation of Cr(VI) Exposed and Unexposed Plant Parts of Tradescantia pallida (Rose) D. R. Hunt. for Cr Removal from Wastewater by Biosorption

Phytoremediation is an efficient method for the removal of heavy metals from contaminated systems. A productive disposal of metal accumulating plants is a major concern in current scenario. In this work, Cr(VI) accumulating Tradescantia pallida plant parts were investigated for its reuse as a biosorbent for the removal of Cr(VI) ions. The effect of pH, contact time, sorbent dosage, Cr(VI) concentration and temperature was examined to optimize these process parameters. Results showed that Cr(VI) exposed/unexposed T. pallida leaf biomass could remove 94% of chromium with a sorption capacity of 64.672 mg g^?1. Whereas the kinetics of Cr(VI) biosorption was well explained by the pseudo second-order kinetic model, the Langmuir model better described the data on Cr(VI) sorption isotherm compared with the Freundlich model. The changes in the free energy (ΔG°), entropy (ΔS°) and enthalpy (ΔH°) were found to be ?5.276 kJ mol^?1, 0.391 kJ mol^?1 K^?1 and 11.346 kJ mol^?1, respectively, which indicated the process to be spontaneous, feasible and endothermic in nature. FTIR spectra of T. pallida leaf biomass revealed the active participation of ligands, such as ?NH, amide, hydroxyl and sulphonate groups present in the biomass for Cr(VI) binding, SEM analysis revealed a porous structure of the biosorbent for an easy uptake of Cr(VI).     

Biosorption of Food Green 3 by a novel green generation composite biosorbent from aqueous environment

A green type composite biosorbent composed of pine, oak, hornbeam, and fir sawdust biomasses modified with cetyltrimethylammonium bromide (CTAB) was first used for biosorption of an unsafe synthetic food dye, Food Green 3 from liquid medium in this study. Batch studies were carried by observing the effects of pH, dye concentration, biosorbent amount, and contact time. The equilibrium data were analyzed using Freundlich, Langmuir, and Dubinin–Radushkevich equations. Freundlich model gave a better conformity than other equations. The maximum dye removal potential of biosorbent was found to be 36.6 mg/g based on Langmuir isotherm. The pseudo-first-order, pseudo-second-order, Elovich, and intra-particle diffusion models were applied to clarify the process kinetics of biosorption. The mechanism studies suggested the biosorption process obeying Elovich kinetics and involving pore diffusion. The estimated values of biosorption free energy from Dubinin–Radushkevich isotherm (E value <8 kJ/mol) and thermodynamic studies (0 < ΔG° < ?20 kJ/mol) implied a spontaneous, feasible, and physical process. Hence, this investigation suggested that the CTAB modified mix sawdust biomass could be a promising biosorbent for biosorption of such problematic dyes from impacted media.     

Biosorption of Acid Black 172 and Congo Red from aqueous solution by nonviable Penicillium YW 01: Kinetic study, equilibrium isotherm and artificial neural network modeling

The main objective of this work was to investigate the biosorption performance of nonviable Penicillium YW 01 biomass for removal of Acid Black 172 metal-complex dye (AB) and Congo Red (CR) in solutions. Maximum biosorption capacities of 225.38 and 411.53 mg g⁻¹ under initial dye concentration of 800 mg L⁻¹, pH 3.0 and 40 °C conditions were observed for AB and CR, respectively. Biosorption data were successfully described with Langmuir isotherm and the pseudo-second-order kinetic model. The Weber-Morris model analysis indicated that intraparticle diffusion was the limiting step for biosorption of AB and CR onto biosorbent. Analysis based on the artificial neural network and genetic algorithms hybrid model indicated that initial dye concentration and temperature appeared to be the most influential parameters for biosorption process of AB and CR onto biosorbent, respectively. Characterization of the biosorbent and possible dye-biosorbent interaction were confirmed by Fourier transform infrared spectroscopy and scanning electron microscopy.     

Biosorption of acid violet dye from aqueous solutions using native biomass of a new isolate of Penicillium sp.

Laboratory investigation of the potential use of Penicillium sp. as biosorbent for the removal of acid violet dye from aqueous solution was studied with respect to pH, temperature, biosorbent, initial dye concentrations. Penicillium sp. decolourizes acid violet (30 mg l⁻¹) within 12 h agitation of 150 rpm at pH 5.7 and temperature of 35 °C. The pellets exhibited a high dye adsorption capacity (5.88 mg g⁻¹) for acid violet dye over a pH range (4–9); the maximum adsorption was obtained at pH 5.7. The increase of temperature favored biosorption for acid violet, but the optimum temperature was 35 °C. Adsorption kinetic data were tested using pseudo-first-order, pseudo-second-order and kinetic studies showed that the biosorption process follows pseudo-first-order rate kinetics with an average rate constant of 0.312 min⁻¹. Isotherm experiments were conducted to determine the sorbent–desorption behavior of examined dye from aqueous solutions using Langmuir and Freundlich equations. Langmuir parameter indicated a maximum adsorption capacity of 4.32 mg g⁻¹ for acid violet and R_L value of 0.377. Linear plot of log q_e vs log C_e shows that applicability of Freundlich adsorption isotherm model. These results suggest that this fungus can be used in biotreatment process as biosorbent for acid dyes.     

Biosorption of Methylene Blue by De-Oiled Algal Biomass: Equilibrium,Kinetics and Artificial Neural Network Modelling

The main objective of the present study is to effectively utilize the de-oiled algal biomass (DAB) to minimize the waste streams from algal biofuel by using it as an adsorbent. Methylene blue (MB) was used as a sorbate for evaluating the potential of DAB as a biosorbent. The DAB was characterized by SEM, FTIR, pH_PZC, particle size, pore volume and pore diameter to understand the biosorption mechanism. The equilibrium studies were carried out by variation in different parameters, i.e., pH (2–9), temperature (293.16–323.16 K), biosorbent dosage (1–10 g L⁻¹), contact time (0–1,440 min), agitation speed (0–150 rpm) and dye concentration (25–2,500 mg L⁻¹). MB removal was greater than 90% in both acidic and basic pH. The optimum result of MB removal was found at 5–7 g L⁻¹ DAB concentration. DAB removes 86% dye in 5 minutes under static conditions and nearly 100% in 24 hours when agitated at 150 rpm. The highest adsorption capacity was found 139.11 mg g⁻¹ at 2,000 mg L⁻¹ initial MB concentration. The process attained equilibrium in 24 hours. It is an endothermic process whose spontaneity increases with temperature. MB biosorption by DAB follows pseudo-second order kinetics. Artificial neural network (ANN) model also validates the experimental dye removal efficiency (R² = 0.97) corresponding with theoretically predicted values. Sensitivity analysis suggests that temperature and agitation speed affect the process most with 23.62% and 21.08% influence on MB biosorption, respectively. Dye adsorption capacity of DAB in fixed bed column was 107.57 mg g⁻¹ in preliminary study while it went up to 139.11 mg g⁻¹ in batch studies. The probable mechanism for biosorption in this study is chemisorptions via surface active charges in the initial phase followed by physical sorption by occupying pores of DAB.     

Biosorption Performance of Multimetal Resistant Fungus Penicillium chrysogenum XJ-1 for Removal of Cu2+ and Cr6+ from Aqueous Solutions

Adsorption for heavy metals via biomaterials such as fungal biomass presents a practical remediation technique for polluted water. Among all known filamentous fungi, Penicillium chrysogenum is widespread in nature and can serve as a biosorbent for heavy metals. In the current study, the ability of P. chrysogenum XJ-1 to remove copper (Cu²⁺) and chromium (Cr⁶⁺) from water was evaluated. The maximum biosorption capacity of XJ-1 for Cu²⁺ reached 42.83 ± 0.57 mg g^?1 dry biomass at pH 5.0 after the equilibrium time of 1.5 h. The maximum biosorption capacity for Cr⁶⁺ at pH 3.0 reached 52.69 ± 1.68 mg g^?1 dry biomass after the equilibrium time of 1.5 h. The biosorption data of XJ-1 biomass were well fitted to the Freundlich isotherm model and the pseudo-second-order Lagergren kinetic model. Laundry powder-treated and HCl-treated XJ-1 biomass significantly enhanced its adsorption capacity to Cu²⁺ and Cr⁶⁺, respectively. HCl and NaOH were suitable desorbents for Cu²⁺/Cr⁶⁺ loading biomass, respectively. Fourier transform infrared spectroscopy analyses revealed that hydroxyl, amine, and sulfonyl groups on the biosorbent contributed to binding Cu²⁺ and Cr⁶⁺ and that carbonyl and carboxyl groups were also vital binding sites of Cu²⁺. Scanning electron microscopy and energy-dispersive x-ray (SEM-EDX) analyses confirmed that considerable amounts of metals were precipitated on the cell surface of XJ-1. Our results suggested that XJ-1 might be used to purify multimetal-contaminated water. This low-cost and eco-friendly biomass of XJ-1 seems to have a broad use in the restoration of metal-contaminated water.     

Biosorption and Desorption of Lead(II) by Hydrilla verticillata

The potential of nonliving biomass of Hydrilla verticillata to adsorb Pb(II) from an aqueous solution containing very low concentrations of Pb(II) was determined in this study. Effects of shaking time, contact time, biosorbent dosage, pH of the medium, and initial Pb(II) concentration on metal-biosorbent interactions were studied through batch adsorption experiments. Maximum Pb(II) removal was obtained after 2 h of shaking. Adsorption capacity at the equilibrium increased with increasing initial Pb(II) concentration, whereas it decreased with increasing biosorbent dosage. The optimum pH of the biosorption was 4.0. Surface titrations showed that the surface of the biosorbent was positively charged at low pH and negatively charged at pH higher than 3.6. Fourier transform infrared (FT-IR) spectra of the biosorbent confirmed the involvement of hydroxyl and C?O of acylamide functional groups on the biosorbent surface in the Pb(II) binding process. Kinetic and equilibrium data showed that the adsorption process followed the pseudo-second-order kinetic model and both Langmuir and Freundlich isothermal models. The mean adsorption energy showed that the adsorption of Pb(II) was physical in nature. The monolayer adsorption capacity of Pb(II) was 125 mg g^?1. The desorption of Pb(II) from the biosorbent by selected desorbing solutions were HNO₃ > Na₂CO₃ > NaOH > NaNO₃.     

Copper biosorption in an aerobic bioreactor

Abstract

This study evaluates the biosorption of copper by aerobic biomass that was selected from surface waters of the San Pedro River in Sonora, Mexico. Using a batch system, 73% biosorption of copper was obtained in 75 minutes. Continuous biosorption assays were carried out for 133 days in an ascending flow aerobic reactor packed with zeolite (AFAR-PZ) that was inoculated with a bacterial consortium. Strains were grown until 1g L^?1 of biomass was obtained. Tests using continuous biosorption were performed as follows: (i) the addition of 50 mg Cu²⁺ L^?1 without recirculation of biomass; (ii) the addition of 20 mg Cu²⁺ L^?1without recirculation of biomass; and (iii) the biomass were recirculated with the addition of 20 mg Cu²⁺ L^?1 to pH 3 to 4. The fourth and fifth assays varied pH between 4 and 5, with 20 mg Cu²⁺ L^?1and the biomass recirculated. Biosorption capacity of the first and second assays was 96% on the first day of experimentation. During the third trial 97% of biosorption was obtained during 6 days and the process was improved by varying the pH. Copper biosorption equilibrium was investigated under the same operating conditions. Langmuir adsorption isotherms were used to fit experimental data. The biosorption capacity of aerobic biomass was 3.08 mmol g^?1. It was demonstrated that this biomass is capable of biosorbing copper and this method has potential for the treatment of industrial effluents contaminated with heavy metals.