Sr2ZnWO6:Eu3+,Bi3+,Li+: a potential white‐emitting phosphor for near‐ultraviolet white light‐emitting diodes

A series of Sr₂ZnWO₆ phosphors co‐doped with Eu³⁺, Bi³⁺ and Li⁺ were prepared using the Pechini method. The samples were tested using X‐ray diffraction and luminescence spectroscopy. The results show that the samples can be effectively excited by near‐ultraviolet (UV) and UV light. The introduction of Bi³⁺ and Li⁺ significantly enhances the fluorescence emission of Sr₂ZnWO₆:Eu³⁺ and changes the light emitted by the phosphors from bluish‐green to white. When excited at 371 nm, Sr_2–x–zZn_1–yWO₆:xEu³⁺,yBi³⁺,zLi⁺ (x = 0.05, y = 0.05, z = 0.05, 0.1 and 0.15) samples emit high‐performance white light. Intense red–orange emission is also observed when excited by UV light. The obtained phosphor is a potential white‐emitting phosphor that could meet the needs of excitation sources with near‐UV chips. In addition, this phosphor might have promising application as a red–orange emitting phosphor for white light‐emitting diodes based on UV light‐emitting diodes. Copyright © 2015 John Wiley & Sons, Ltd.     

Luminescence and energy‐transfer properties of color‐tunable Ca2Mg0.25Al1.5Si1.25O7:Ce3+/Eu2+/Tb3+ phosphors for ultraviolet light‐emitting diodes

A series of Ca₂Mg_0.25Al_1.5Si_1.25O₇:Ce³⁺/Eu²⁺/Tb³⁺ phosphors was been prepared via a conventional high temperature solid‐state reaction and their luminescence properties were studied. The emission spectra of Ca₂Mg_0.25Al_1.5Si_1.25O₇:Ce³⁺,Eu²⁺ and Ca₂Mg_0.25Al_1.5Si_1.25O₇:Ce³⁺,Tb³⁺ phosphors show not only a band due to Ce³⁺ ions (409 nm) but also as a band due to Eu²⁺ (520 nm) and Tb³⁺ (542 nm) ions. More importantly, the effective energy transfer from Ce³⁺ to Eu²⁺ and Tb³⁺ ions was confirmed and investigated by emission/excitation spectra and luminescent decay behaviors. Furthermore, the energy level scheme and energy transfer mechanism were investigated and were demonstrated to be of resonant type via dipole–dipole (Ce³⁺ to Eu²⁺) and dipole–quadrupole (Ce³⁺ to Tb³⁺) reactions, respectively. Under excitation at 350 nm, the emitting color could be changed from blue to green by adjusting the relative doping concentration of Ce³⁺ and Eu²⁺ ions as well as Ce³⁺ and Tb³⁺ ions. The above results indicate that Ca₂Mg_0.25Al_1.5Si_1.25O₇:Ce³⁺,Eu²⁺/Tb³⁺ are promising single‐phase blue‐to‐green phosphors for application in phosphor conversion white‐light‐emitting diodes. Copyright © 2015 John Wiley & Sons, Ltd.     

Persistent luminescence of CaMgSi2O6:Eu2+,Dy3+ and CaMgSi2O6:Eu2+,Ce3+ phosphors prepared using the solid‐state reaction method

CaMgSi₂O₆:Eu²⁺,Dy³⁺ and CaMgSi₂O₆:Eu²⁺,Ce³⁺ phosphors were synthesized using the solid‐state reaction method. X‐Ray diffraction (XRD) and photoluminescence (PL) analyses were used to characterize the phosphors. The XRD results revealed that the synthesized CaMgSi₂O₆:Eu²⁺,Dy³⁺ and CaMgSi₂O₆:Eu²⁺,Ce³⁺ phosphors were crystalline and are assigned to the monoclinic structure with a space group C2/c. The calculated crystal sizes of CaMgSi₂O₆:Eu²⁺,Dy³⁺ and CaMgSi₂O₆:Eu²⁺,Ce³⁺ phosphors with a main (221) diffraction peak were 44.87 and 53.51 nm, respectively. Energy‐dispersive X‐ray spectroscopy (EDX) confirmed the proper preparation of the sample. The PL emission spectra of CaMgSi₂O₆:Eu²⁺,Dy³⁺ and CaMgSi₂O₆:Eu²⁺,Ce³⁺ phosphors have a broad band peak at 444.5 and 466 nm, respectively, which is due to electronic transition from 4f⁶5d¹ to 4f⁷. The afterglow results indicate that the CaMgSi₂O₆:Eu²⁺,Dy³⁺ phosphor has better persistence luminescence than the CaMgSi₂O₆:Eu²⁺,Ce³⁺ phosphor. Copyright © 2015 John Wiley & Sons, Ltd.     

Energy transfer induced white‐light‐emitting phosphor by co‐doping Ce3+, Tb3+ and Mn2+ into the single Ba9Lu2Si6O24 host

In the Ba₉Lu₂Si₆O₂₄ (BLS) host, Ce³⁺ shows cyan emissions peaking at 490 nm under 400 nm excitations. BLS:Tb³⁺ only can be effectively excited by 254 nm light and gives rise to green emissions at 553 nm. However, both the cyan and green emissions can be obtained in BLS:Ce³⁺,Tb³⁺ under 400 nm excitations due to effective energy transfers from Ce³⁺ to Tb³⁺. BLS:Mn²⁺ shows red emissions peaking at 610 nm under 414 nm excitations. By co‐doping Ce³⁺, Tb³⁺ and Mn²⁺, tunable full‐color emissions were obtained. The BLS:0.3Ce³⁺,0.6Tb³⁺,0.15Mn²⁺ single phosphor exhibits a white light with a high color rendering index of 85 and a correlated color temperature of 5480 K under 400 nm excitation.     

Luminescent properties of single‐phase Ba2‐x‐1.5y‐1.5zP2O7:xEu2+,yCe3+, zTb3+ phosphors for white light‐emitting diode

A series of Ba₂P₂O₇:xEu²⁺,yCe³⁺,zTb³⁺ phosphors was synthesized via a co‐precipitation method, then their crystal structure, quantum efficiency and luminescent properties were analyzed by XRD and FL, respectively. The results showed that these phosphors not only presented the excitation characteristics of Ba₂P₂O₇:xEu²⁺,zTb³⁺, but also exhibited that of the Ba₂P₂O₇:yCe³⁺,zTb³⁺ phosphor. Meanwhile, the tri‐doped phosphor showed a stronger absorption around 320 nm in contrast with the Eu²⁺/Ce³⁺:Tb³⁺ co‐doped phosphor. Not only can energy transfer from Ce³⁺→Eu²⁺ be observed; the energy transfer mechanism from Eu²⁺ to Tb³⁺ is discussed in the tri‐doped system. Ce³⁺ affects the luminescence properties of Ba₂P₂O₇:xEu²⁺,yCe³⁺,zTb³⁺ phosphors just as the sensitizer whereas Eu²⁺ is considered both as the sensitizer and the activator. The chromaticity coordinates of tri‐doped phosphors excited at 320 nm stayed steadily in the bluish‐white light region,and the emitted color and color temperature (CCT) of these phosphors could be tuned by adjusting the relative contents of Eu²⁺, Ce³⁺ and Tb³⁺. Hence, the single phase Ba₂P₂O₇:xEu²⁺,yCe³⁺,zTb³⁺ phosphors may be considered as potential candidates for white light‐emitting diodes.     

The luminescent properties and crystal structure of Sr(1.5‐x)‐(1.5y)Mg0.5SiO4:xEu2+,yCe3+ blue phosphor synthesized by co‐precipitation method

In order to improve the luminescent performance of silicate blue phosphors, Sr_{(1.5‐x)‐(1.5y)}Mg_0.5SiO₄:xEu²⁺,yCe³⁺ phosphors were synthesized using one‐step calcination of a precursor prepared by chemical co‐precipitation. The crystal structure and luminescent properties of the phosphors were analyzed using X‐ray diffraction and fluorescence spectrophotometry, respectively. Because the activated ions (Eu²⁺) can occupy two different types of sites (Sr₁ and Sr₂), the emission spectrum of Eu²⁺ excited at 350 nm contains two single bands (EM₁ and EM₂) in the wavelength range 400–550 nm, centered at 463 nm, and the emission intensity first increases and then decreases with increasing concentrations of Eu²⁺ ions. Co‐doping of Ce³⁺ ions can greatly enhance the emission intensity of Eu²⁺ by transferring its excitation energy to Eu²⁺. Because of concentration quenching, a higher substitution concentration of Ce³⁺ can lead to a decrease in the intensity. Meanwhile, the quantum efficiency of the phosphor is improved after doping with Ce³⁺, and a blue shift phenomenon is observed in the CIE chromaticity diagram. The results indicate that Sr_{(1.5‐x)‐(1.5y)}Mg_0.5SiO₄:xEu²⁺,yCe³⁺ can be used as a potential new blue phosphor for white light‐emitting diodes.     

Dual emission of Ce3+,Mn2+‐coactivated Ca3YNa(PO4)3F via energy transfer: a single component white/yellow‐emitting phosphor

A series of Ce³⁺,Mn²⁺‐coactivated Ca₃YNa(PO₄)₃F phosphors were synthesized via a traditional solid‐state reaction under a reductive atmosphere. X‐Ray powder diffraction was used to confirm that the crystal structure and diffraction peaks of Ce³⁺/Mn²⁺‐doped samples matched well with the standard data. A spectral overlap between the emission band of Ce³⁺ and the excitation band of Mn²⁺ suggested the occurrence of energy transfer from Ce³⁺ to Mn²⁺. With increasing Mn²⁺ content, the emission intensities and lifetime values of the Ce³⁺ emission for Ca₃YNa(PO₄)₃F:Ce³⁺,Mn²⁺ phosphors linearly decrease, whereas the energy transfer efficiencies gradually increase to 89.35%. By adjusting the relative concentrations of Ce³⁺ and Mn²⁺, the emission hues are tuned from blue to white and eventually to yellow. These results suggest that Ca₃YNa(PO₄)₃F:Ce³⁺,Mn²⁺ phosphors have promising application as white‐emitting phosphors for near‐ultraviolet light‐emitting diodes.     

Tunable white light emission from single‐phased Li2SrSiO4:Dy3+ phosphors by co‐doping with Eu3+

A series of single‐phase full‐color emitting Li₂Sr_1−x−ySiO₄:xDy³⁺,yEu³⁺ phosphors were synthesized by solid‐state reaction and characterized by X‐ray diffraction and photoluminescence analyses. The samples showed emission peaks at 488 nm (blue), 572 nm (yellow), 592 nm (orange) and 617 nm (red) under 393 nm excitation. The photoluminescence excitation spectra, comprising the Eu–O charge transfer band and 4f–4f transition bands of Dy³⁺ and Eu³⁺, range from 200 to 500 nm. The Commission Internationale de I'Eclairage chromaticity coordinates for Li₂Sr_0.98−xSiO₄:0.02Dy³⁺,xEu³⁺ phosphors were simulated. By manipulating Eu³⁺ and Dy³⁺ concentrations, the color points of Li₂Sr_1−x−ySiO₄:xDy³⁺,yEu³⁺ were tuned from the greenish‐white region to white light and eventually to reddish‐white region, demonstrating that a tunable white light can be obtained by Li₂Sr_1−x−ySiO₄:xDy³⁺,yEu³⁺ phosphors. Li₂Sr_0.98−xSiO₄:0.02Dy³⁺, xEu³⁺ can serve as a white‐light‐emitting phosphor for phosphor‐converted light‐emitting diode. Copyright © 2014 John Wiley & Sons, Ltd.     

Resonant and non‐resonant energy transfer from Ce3+ → X (X = Tb3+, Eu3+ or Dy3+) in NaMgSO4F material

An inorganic NaMgSO₄F fluoride material was prepared by the wet chemical method and studied for its photoluminescence (PL) and resonant–non‐resonant energy transfer (RET and NORET) capabilities between Ce³⁺ → Tb³⁺, Ce³⁺ → Eu³⁺ and Ce³⁺ → Dy³⁺ rare earth ions. The Tb³⁺ emission for Ce³⁺ → Tb³⁺ transfers under ultraviolet (UV) wavelengths peaked at 491, 547, and 586 nm, for excitation at 308 nm due to ⁵D₄ → ⁷F_J (J = 4, 5, 6) transitions. Eu emission spectra were observed at 440 nm (Eu²⁺), 593 nm and 616 nm (Eu³⁺) recorded for different concentrations of materials, whereas Dy³⁺ emission from Ce³⁺ → Dy³⁺ transfer under UV wavelengths peaked at 485 nm and 577 nm due to ⁴F_9/2 → ⁶H_15/2 and ⁶H_13/2 transitions. The purpose of the present study is to understand the RET and NORET effects of Tb³⁺, Eu³⁺ and Dy³⁺ co‐doping in a NaMgSO₄F:Ce³⁺ luminescent material, which could be used as a green‐emitting material for lamp phosphors.     

Design,synthesis and luminescence properties of Ba2YB2O6Cl‐ and Ba2YB2O6F‐based phosphors

Using a high‐temperature solid‐state reaction, the chlorine in Ba₂YB₂O₆Cl is gradually replaced by F, and a new compound with the nominal chemical formula Ba₂YB₂O₆F and two phosphors doped with Ce³⁺ and Eu³⁺, respectively, are obtained. X‐Ray diffraction and photoluminescence spectroscopy are used to characterize the as‐synthesized samples. The as‐synthesized Ba₂YB₂O₆Cl exhibits bright blue emission in the spectral range ~ 330–410 nm with a maximum around 363 nm under X‐ray or UV excitation. Ba₂YB₂O₆F:0.01Ce³⁺ exhibits blue emission in the range ~ 340–570 nm with a maximum around 383 nm. Ba₂YB₂O₆F:0.01Eu³⁺ exhibits a predominantly ⁵D₀–⁷ F₂ emission (~610 nm) and the relative intensities of the ⁵D₀–⁷ F_0,1,2 emissions are tunable under different wavelength UV excitation. The luminescence behaviors of the two phosphors are explained simply in terms of the host composition and site occupancy probability of Ce³⁺ and Eu³⁺, respectively. The results indicate that these phosphors have potential application as a blue phosphor or as a red phosphor. Copyright © 2014 John Wiley & Sons, Ltd.     

Energy transfer in M5(PO4)3 F:Eu2+,Ce3+ (M = Ca and Ba) phosphors

M₅(PO₄)₃ F:Eu²⁺ (M = Ca and Ba) co‐doped with Ce³⁺ phosphors were successfully prepared by the combustion synthesis method. The introduction of co‐dopant (Ce³⁺) into the host enhanced the luminescent intensity of the M₅(PO₄)₃ F:Eu²⁺ (M = Ca and Ba) efficiently. Previously, we have reported the synthesis and photoluminescence properties of same phosphors. The aim of this article is to report energy transfer mechanism between Ce³⁺?Eu²⁺ ions in M₅(PO₄)₃ F:Eu²⁺ (M = Ca and Ba) phosphors, where Ce³⁺ ions act as sensitizers and Eu²⁺ ions act as activators. The M₅(PO₄)₃ F:Eu²⁺ (M = Ca and Ba) co‐doped with Ce³⁺ phosphor exhibits great potential for use in white ultraviolet (UV) light‐emitting diode applications to serve as a single‐phased phosphor that can be pumped with near‐UV or UV light‐emitting diodes. Copyright © 2013 John Wiley & Sons, Ltd.     

Luminescent properties and energy transfer in the green phosphors LaBSiO5:Tb3+,Ce3+

LaBSiO₅ phosphors doped with Ce³⁺ and Tb³⁺ were synthesized using the conventional solid‐state method at 1100 °C. The phase purity and luminescent properties of these phosphors are investigated. LaBSiO₅:Tb³⁺ phosphors show intense green emission, and LaBSiO₅ phosphors doped with Ce³⁺ show blue–violet emission under UV light excitation. LaBSiO₅ phosphors co‐doped with Ce³⁺ and Tb³⁺ exhibit blue–violet and green emission under excitation by UV light. The blue–violet emission is due to the 5d–4f transition of Ce³⁺ and the green emission is ascribed to the ⁵D₄ → ⁷ F₅ transition of Tb³⁺. The spectral overlap between the excitation band of Tb³⁺ and the emission band of Ce³⁺ supports the occurrence of energy transfer from Ce³⁺ to Tb³⁺, and the energy transfer process was investigated. Copyright © 2014 John Wiley & Sons, Ltd.     

Synthesis and photoluminescence characteristics of (Y,Gd)BO3:RE (RE = Eu3+, Ce3+, Dy3+ and Tb3+) phosphors for blue chip and near‐UV white LEDs

A series of Eu³⁺‐, Ce³⁺‐, Dy³⁺‐ and Tb³⁺‐doped (Y,Gd)BO₃ phosphors was synthesized by a solid‐state diffusion method. X‐Ray diffraction confirmed their hexagonal structure and the scanning electron microscopy results showed crystalline particles. The excitation spectra revealed that (Y,Gd)BO₃ phosphors doped with Eu³⁺, Ce³⁺ , Dy³⁺ and Tb³⁺ are effectively excited with near UV‐light of 395 nm/blue light, 364, 351 and 314 nm, respectively. Photoluminescence spectra of Eu³⁺‐, Ce³⁺‐ and Tb³⁺/Dy³⁺‐doped phosphor showed intense emission of reddish orange, blue and white light, respectively. The phosphor Y_0.60Gd_0.38BO₃:Ce_0.02 showed CIE 1931 color coordinates of (0.158, 0.031) and better color purity compared with commercially available blue BAM:Eu²⁺ phosphor. The phosphor (Y,Gd)BO₃ doped with Eu³⁺, Dy³⁺ and Tb³⁺ showed CIE 1931 color coordinates of (0.667, 0.332), (0.251, 0.299) and (0.333, 0.391) respectively. Significant photoluminescence characteristics of the prepared phosphors indicate that they might serve as potential candidates for blue chip and near‐UV white light‐emitting diode applications. Copyright © 2015 John Wiley & Sons, Ltd.     

Photoluminescence and thermoluminescence properties of Eu2+ doped and Eu2+,Dy3+ co‐doped Ba2MgSi2O7 phosphors

In this work, we report the preparation, characterization, comparison and luminescence mechanisms of Eu²⁺‐doped and Eu²⁺,Dy³⁺‐co‐doped Ba₂MgSi₂O₇ (BMSO) phosphors. Prepared phosphors were synthesized via a high temperature solid‐state reaction method. All prepared phosphors appeared white. The phase structure, particle size, and elemental analysis were analyzed using X‐ray diffraction (XRD), transmission electron microscopy (TEM) and energy‐dispersive X‐ray (EDX) analysis. The luminescence properties of the phosphors were investigated by thermoluminescence (TL) and photoluminescence (PL). The PL excitation and emission spectra of Ba₂MgSi₂O₇:Eu²⁺ showed the peak to be around 381 nm and 490 nm respectively. The PL excitation spectrum of Ba₂MgSi₂O₇:Eu²⁺Dy³⁺ showed the peak to be around 341 nm and 388 nm, and the emission spectrum had a broad band around 488 nm. These emissions originated from the 4f⁶ 5d¹ to 4f⁷ transition of Eu²⁺. TL analysis revealed that the maximum TL intensity was found at 5 mol% of Eu²⁺ doping in Ba₂MgSi₂O₇ phosphors after 15 min of ultraviolet (UV) light exposure. TL intensity was increased when Dy³⁺ ions were co‐doped in Ba₂MgSi₂O₇:Eu²⁺ and maximum TL intensity was observed for 2 mol% of Dy³⁺. TL emission spectra of Ba_1.95MgSi₂O₇:0.05Eu²⁺ and Ba_1.93MgSi₂O₇:0.05Eu²⁺,0.02Dy³⁺ phosphors were found at 500 nm. TL intensity increased with UV exposure time up to 15 min, then decreased for the higher UV radiation dose for both Eu doping and Eu,Dy co‐doping. The trap depths were calculated to be 0.54 eV for Ba_1.95MgSi₂O₇:0.05Eu²⁺ and 0.54 eV and 0.75 eV for Ba_1.93MgSi₂O₇:0.05Eu²⁺,0.02Dy³⁺ phosphors. It was observed that co‐doping with small amounts of Dy³⁺ enhanced the thermoluminescence properties of Ba₂MgSi₂O₇ phosphor. Copyright © 2016 John Wiley & Sons, Ltd. [Correction added on 5 April 2016, after first online publication: The following parts of the abstract have been edited for consistency. '4f65d1' has been corrected to '4f⁶ 5d¹', '4f7' has been corrected to '4f⁷', 'Ba1.95' has been corrected to 'Ba_1.95' and 'Ba1.93' has been corrected to 'Ba_1.93' respectively.]     

Enhancement of the luminescence properties of Sr3(PO4)2:Dy3+,Li+ white‐light‐emitting phosphors by charge compensator Li+ co‐doping

Sr₃(PO₄)₂:Dy³⁺,Li⁺ phosphors were prepared using a simple high temperature solid method for luminescence enhancement. The structures of the as‐prepared samples agreed well with the standard phase of Sr₃(PO₄)₂, even when Dy³⁺ and Li⁺ were introduced. Under ultraviolet excitation at 350 nm, the Sr₃(PO₄)₂:Dy³⁺ sample exhibited two emission peaks at 483 nm and 580 nm, which were due to the ⁴F_9/2 → ⁶H_15/2 and ⁴F_9/2 → ⁶H_13/2 transitions of Dy³⁺ ions, respectively. A white light was fabricated using these two emissions from the Sr₃(PO₄)₂:Dy³⁺ phosphors. The luminescence properties of Sr₃(PO₄)₂:Dy³⁺,Li⁺ phosphors, including emission intensity and decay time, were improved remarkably with the addition of Li⁺ as the charge compensator, which would promote their application in near‐ultraviolet excited white‐light‐emitting diodes.     

Studies on the luminescence properties of cerium co‐doping on Ca2MgSi2O7:Eu2+ phosphor by solid‐state reaction method

Ca₂MgSi₂O₇:Ce³⁺, Ca₂MgSi₂O₇:Eu²⁺ and Ca₂MgSi₂O₇:Eu²⁺,Ce³⁺ phosphors were prepared using the solid‐state reaction method. The crystal structures of the sintered phosphors were of melilite type, which has a tetragonal crystallography. The chemical compositions of the sintered phosphors was confirmed by energy dispersive X‐ray spectroscopy. The different thermoluminescence kinetic parameters [activation energy (E), frequency factor (s) and order of the kinetics (b)] of these phosphors were evaluated and compared using the peak shape method. Under ultraviolet excitation, the emission spectra of both Ca₂MgSi₂O₇:Eu²⁺ and Ca₂MgSi₂O₇:Eu²⁺,Ce³⁺ phosphors were composed of a broad emission band peaking at 530 nm. When the Ca₂MgSi₂O₇:Eu²⁺ phosphor is co‐doped with Ce³⁺ ions, photoluminescence, afterglow and mechanoluminescence intensity was strongly enhanced. Ca₂MgSi₂O₇:Eu²⁺ showed some afterglow with a short persist time. On incorporation of Ce³⁺, efficient energy transfer from Ce³⁺ to Eu²⁺ was found and the emission intensity of Eu²⁺ was enhanced. The mechanoluminescence intensities of Ca₂MgSi₂O₇:Ce³⁺, Ca₂MgSi₂O₇:Eu²⁺ and Ca₂MgSi₂O₇:Eu²⁺,Ce³⁺ phosphors increased proportionally increased with the increase in impact velocity, which suggests that these phosphors can be used as sensors to detect stress in an object.     

Optical properties of Eu2+/Eu3+ mixed valence phosphor Ca2SiO2F2:Eu2+/Eu3+

The Eu²⁺/Eu³⁺ mixed valence phosphor Ca₂SiO₂F₂:Eu²⁺/Eu³⁺ was prepared using a solid‐state reaction synthesis method in a CO atmosphere, and the optical properties were investigated. The spectroscopic properties revealed that Ca²⁺ ions were occupied by both Eu²⁺ and Eu³⁺ ions in Ca₂SiO₂F₂, and both ions were able to generate their characteristic emissions. A broad 5d → 4f Eu²⁺ band at ~470 nm and narrow 4f → 4f Eu³⁺ peaks upon excitation with n‐UV light were observed. The ratio between Eu²⁺ and Eu³⁺ emissions changed regularly, and the relative intensity of the red component from Eu³⁺ became systematically stronger with increasing overall Eu content. As a result, the emission color of these phosphors can be tunable from blue to pink under n‐UV light excitation.     

Luminescent properties of Ca3SiO4Cl2 co‐doped with Ce3+ and Eu2+ for near‐ultraviolet light‐emitting diodes

Ca₃SiO₄Cl₂ co‐doped with Ce³⁺,Eu²⁺ was prepared by high temperature reaction. The structure, luminescent properties and the energy transfer process of Ca₃SiO₄Cl₂: Ce³⁺,Eu²⁺ were investigated. Eu²⁺ ions can give enhanced green emission through Ce³⁺ → Eu²⁺ energy transfer in these phosphors. The green phosphor Ca_2.9775SiO₄Cl₂:0.0045Ce³⁺,0.018Eu²⁺ showed intense green emission with broader excitation in the near‐ultraviolet light range. A green light‐emitting diode (LED) based on this phosphor was made, and bright green light from this green LED could be observed by the naked eye under 20 mA current excitation. Hence it is considered to be a good candidate for the green component of a three‐band white LED. Copyright © 2015 John Wiley & Sons, Ltd.     

Synthesis and luminescence characterization of Y2BaZnO5:RE (RE = Eu3+, Tb3+, Pr3+ and Sm3+) phosphors

Modified synthesis and luminescence of Y₂BaZnO₅ phosphors activated with the rare earths (RE) Eu³⁺, Tb³⁺, Pr³⁺ and Sm³⁺ are reported. RE₂BaZnO₅ phosphors have attracted attention because of their interesting magnetic and optical properties; and are usually prepared using a two‐step solid‐state reaction. In the first step, carbonates or similar precursors are thoroughly mixed and heated at 900°C to decompose them to oxides. To eliminate the unwanted phases like BaRE₂O₄, the resulting powders are reheated at 1100°C for a long time. We prepared Y₂BaZnO₅ phosphors activated with various activators by replacing the first step with combustion synthesis. The photoluminescence results are presented. The photoluminescence results for Eu³⁺, Tb³⁺ and Pr³⁺ are in good agreement with the literature. However, photoluminescence emission from Sm³⁺ has not been documented previously. The excitation spectrum of Eu³⁺ is dominated by a charge transfer band around 261 nm, and an additional band around 238 nm is always present, irrespective of the type of activator. The presence of this band for all these different types of activators was interpreted as host absorption.     

A novel red emitting phosphor LiBaB9O15:Sm2+/Sm3+, li+ with broad excitation band for white LEDs

A novel tunable red emitting phosphor LiBaB₉O₁₅:Sm²⁺/Sm³⁺, Li⁺ with broad excitation band was synthesized by a high temperature solid‐state method. Luminescence properties were investigated in detail by luminescence, X‐ray photoelectron spectroscopy (XPS) spectra and CIE chromaticity coordinates. XPS data confirmed that there were Sm³⁺ in LiBaB₉O₁₅:Sm³⁺ and Sm²⁺/Sm³⁺ in LiBaB₉O₁₅:Sm²⁺/Sm³⁺, respectively. Spectral property of LiBaB₉O₁₅:Sm³⁺, LiBaB₉O₁₅:Sm³⁺/Sm²⁺ and LiBaB₉O₁₅:Sm²⁺, Li⁺ presented that the excitation band of Sm³⁺ widened and the excitation band of Sm²⁺ ranged from 350 to 450 nm. And the red light color is tunable with changing Li⁺ concentration. The results indicated that LiBaB₉O₁₅:Sm²⁺/Sm³⁺, Li⁺ may be promising red phosphor for white light emitting diodes.