Sr2ZnWO6:Eu3+,Bi3+,Li+: a potential white‐emitting phosphor for near‐ultraviolet white light‐emitting diodes

A series of Sr₂ZnWO₆ phosphors co‐doped with Eu³⁺, Bi³⁺ and Li⁺ were prepared using the Pechini method. The samples were tested using X‐ray diffraction and luminescence spectroscopy. The results show that the samples can be effectively excited by near‐ultraviolet (UV) and UV light. The introduction of Bi³⁺ and Li⁺ significantly enhances the fluorescence emission of Sr₂ZnWO₆:Eu³⁺ and changes the light emitted by the phosphors from bluish‐green to white. When excited at 371 nm, Sr_2–x–zZn_1–yWO₆:xEu³⁺,yBi³⁺,zLi⁺ (x = 0.05, y = 0.05, z = 0.05, 0.1 and 0.15) samples emit high‐performance white light. Intense red–orange emission is also observed when excited by UV light. The obtained phosphor is a potential white‐emitting phosphor that could meet the needs of excitation sources with near‐UV chips. In addition, this phosphor might have promising application as a red–orange emitting phosphor for white light‐emitting diodes based on UV light‐emitting diodes. Copyright © 2015 John Wiley & Sons, Ltd.     

The luminescent properties and crystal structure of Sr(1.5‐x)‐(1.5y)Mg0.5SiO4:xEu2+,yCe3+ blue phosphor synthesized by co‐precipitation method

In order to improve the luminescent performance of silicate blue phosphors, Sr_{(1.5‐x)‐(1.5y)}Mg_0.5SiO₄:xEu²⁺,yCe³⁺ phosphors were synthesized using one‐step calcination of a precursor prepared by chemical co‐precipitation. The crystal structure and luminescent properties of the phosphors were analyzed using X‐ray diffraction and fluorescence spectrophotometry, respectively. Because the activated ions (Eu²⁺) can occupy two different types of sites (Sr₁ and Sr₂), the emission spectrum of Eu²⁺ excited at 350 nm contains two single bands (EM₁ and EM₂) in the wavelength range 400–550 nm, centered at 463 nm, and the emission intensity first increases and then decreases with increasing concentrations of Eu²⁺ ions. Co‐doping of Ce³⁺ ions can greatly enhance the emission intensity of Eu²⁺ by transferring its excitation energy to Eu²⁺. Because of concentration quenching, a higher substitution concentration of Ce³⁺ can lead to a decrease in the intensity. Meanwhile, the quantum efficiency of the phosphor is improved after doping with Ce³⁺, and a blue shift phenomenon is observed in the CIE chromaticity diagram. The results indicate that Sr_{(1.5‐x)‐(1.5y)}Mg_0.5SiO₄:xEu²⁺,yCe³⁺ can be used as a potential new blue phosphor for white light‐emitting diodes.     

Luminescence behavior of Li2Sr1‐3x/2EuxSiO4 red phosphors for LED applications

Red‐emitting Li₂Sr_1‐3x/2Eu_xSiO₄ 0≤x≤0.5) phosphors were synthesized at 900°C in air by a solid‐state reaction. The synthesized phosphors were characterized by X‐ray powder diffraction, photoluminescence (PL) excitation (PLE) and PL spectra. The results from the PLE spectra suggest that the strong 394 nm excitation peak associated with the ⁵L₆ state of Eu³⁺ ions is of significance for near ultraviolet pumped white light‐emitting diodes and solid‐state lighting. It is also noted that the position of the charge transfer state of Eu³⁺ ions shifts towards the higher energy side (blue shift) by increasing the content of Eu³⁺ ions. The predominant emissions of Eu³⁺ ions under 394 nm excitation are observed at 580, 593, 614, 656 and 708 nm, which are attributed to the ⁵D₀ → ⁷F_J (J = 0, 1, 2, 3 and 4), respectively. The PL results reveal that the optimal content of the red‐emitting Li₂Sr_1‐3x/2Eu_xSiO₄ phosphors is x = 0.475. Simulation of the white light excited by 394 nm near ultraviolet light has also been carried out for its potential white light‐emitting diode applications. Copyright © 2013 John Wiley & Sons, Ltd.     

Enhancement of the luminescence properties of Sr3(PO4)2:Dy3+,Li+ white‐light‐emitting phosphors by charge compensator Li+ co‐doping

Sr₃(PO₄)₂:Dy³⁺,Li⁺ phosphors were prepared using a simple high temperature solid method for luminescence enhancement. The structures of the as‐prepared samples agreed well with the standard phase of Sr₃(PO₄)₂, even when Dy³⁺ and Li⁺ were introduced. Under ultraviolet excitation at 350 nm, the Sr₃(PO₄)₂:Dy³⁺ sample exhibited two emission peaks at 483 nm and 580 nm, which were due to the ⁴F_9/2 → ⁶H_15/2 and ⁴F_9/2 → ⁶H_13/2 transitions of Dy³⁺ ions, respectively. A white light was fabricated using these two emissions from the Sr₃(PO₄)₂:Dy³⁺ phosphors. The luminescence properties of Sr₃(PO₄)₂:Dy³⁺,Li⁺ phosphors, including emission intensity and decay time, were improved remarkably with the addition of Li⁺ as the charge compensator, which would promote their application in near‐ultraviolet excited white‐light‐emitting diodes.     

Synthesis and photoluminescence characteristics of (Y,Gd)BO3:RE (RE = Eu3+, Ce3+, Dy3+ and Tb3+) phosphors for blue chip and near‐UV white LEDs

A series of Eu³⁺‐, Ce³⁺‐, Dy³⁺‐ and Tb³⁺‐doped (Y,Gd)BO₃ phosphors was synthesized by a solid‐state diffusion method. X‐Ray diffraction confirmed their hexagonal structure and the scanning electron microscopy results showed crystalline particles. The excitation spectra revealed that (Y,Gd)BO₃ phosphors doped with Eu³⁺, Ce³⁺ , Dy³⁺ and Tb³⁺ are effectively excited with near UV‐light of 395 nm/blue light, 364, 351 and 314 nm, respectively. Photoluminescence spectra of Eu³⁺‐, Ce³⁺‐ and Tb³⁺/Dy³⁺‐doped phosphor showed intense emission of reddish orange, blue and white light, respectively. The phosphor Y_0.60Gd_0.38BO₃:Ce_0.02 showed CIE 1931 color coordinates of (0.158, 0.031) and better color purity compared with commercially available blue BAM:Eu²⁺ phosphor. The phosphor (Y,Gd)BO₃ doped with Eu³⁺, Dy³⁺ and Tb³⁺ showed CIE 1931 color coordinates of (0.667, 0.332), (0.251, 0.299) and (0.333, 0.391) respectively. Significant photoluminescence characteristics of the prepared phosphors indicate that they might serve as potential candidates for blue chip and near‐UV white light‐emitting diode applications. Copyright © 2015 John Wiley & Sons, Ltd.     

Luminescent properties of Ca3SiO4Cl2 co‐doped with Ce3+ and Eu2+ for near‐ultraviolet light‐emitting diodes

Ca₃SiO₄Cl₂ co‐doped with Ce³⁺,Eu²⁺ was prepared by high temperature reaction. The structure, luminescent properties and the energy transfer process of Ca₃SiO₄Cl₂: Ce³⁺,Eu²⁺ were investigated. Eu²⁺ ions can give enhanced green emission through Ce³⁺ → Eu²⁺ energy transfer in these phosphors. The green phosphor Ca_2.9775SiO₄Cl₂:0.0045Ce³⁺,0.018Eu²⁺ showed intense green emission with broader excitation in the near‐ultraviolet light range. A green light‐emitting diode (LED) based on this phosphor was made, and bright green light from this green LED could be observed by the naked eye under 20 mA current excitation. Hence it is considered to be a good candidate for the green component of a three‐band white LED. Copyright © 2015 John Wiley & Sons, Ltd.     

Luminescence study of Eu3+doped Li6Y(BO3)3 phosphor for solid‐state lighting

In this study, Li₆Y_1–xEu_x(BO₃)₃ phosphor was successfully synthesized using a modified solid‐state diffusion method. The Eu³⁺ ion concentration was varied at 0.05, 0.1, 0.2, 0.5 and 1 mol%. The phosphor was characterized for phase purity, morphology, luminescent properties and molecular transmission at room temperature. The XRD pattern suggests a result closely matching the standard JCPDS file (#80‐0843). The emission and excitation spectra were followed to discover the luminescence traits. The excitation spectra indicate that the current phosphor can be efficiently excited at 395 nm and at 466 nm (blue light) to give emission at 595 and 614 nm due to the ⁵D₀ → ⁷F_j transition of Eu³⁺ ions. Concentration quenching was observed at 0.5 mol% Eu³⁺ in the Li₆Y_1–xEu_x(BO₃)₃ host lattice. Strong red emission with CIE chromaticity coordinates of phosphor is x = 0.63 and y = 0.36 achieved with dominant red emission at 614 nm the ⁵D₀ → ⁷ F₂ electric dipole transition of Eu³⁺ ions. The novel Li₆Y_1–xEu_x(BO₃)₃ phosphor may be a suitable red‐emitting component for solid‐state lighting using double‐excited wavelengths, i.e. near‐UV at 395 nm and blue light at 466 nm. Copyright © 2015 John Wiley & Sons, Ltd.     

Photoluminescence properties and energy transfer in Ce3+/Dy3+ co‐doped Sr3MgSi2O8 phosphors for potential application in ultraviolet white light‐emitting diodes

Sr₃MgSi₂O₈:Ce³⁺, Dy³⁺ phosphors were prepared by a solid‐state reaction technique and the photoluminescence properties were investigated. The emission spectra show not only a band due to Ce³⁺ ions (403 nm) but also as a band due to Dy³⁺ ions (480, 575 nm) (UV light excitation). The photoluminescence properties reveal that effective energy transfer occurs in Ce³⁺/Dy³⁺ co‐doped Sr₃MgSi₂O₈ phosphors, and the co‐doping of Ce³⁺ could enhance the emission intensity of Dy³⁺ to a certain extent by transferring its energy to Dy³⁺. The Ce³⁺/Dy³⁺ energy transfer was investigated by emission/excitation spectra, and photoluminescence decay behaviors. In Sr_2.94MgSi₂O₈:0.01Ce³⁺, 0.05Dy³⁺ phosphors, the fluorescence lifetime of Dy³⁺ (from 3.35 to 27.59 ns) is increased whereas that of Ce³⁺ is greatly decreased (from 43.59 to 13.55 ns), and this provides indirect evidence of the Ce³⁺ to Dy³⁺ energy transfer. The varied emitted color of Sr₃MgSi₂O₈:Ce³⁺, Dy³⁺ phosphors from blue to white were achieved by altering the concentration ratio of Ce³⁺ and Dy³⁺. These results indicate Sr₃MgSi₂O₈:Ce³⁺, Dy³⁺ may be as a candidate phosphor for white light‐emitting diodes. Copyright © 2012 John Wiley & Sons, Ltd.     

Eu3+‐activated Y2MoO6: a narrow band red‐emitting phosphor with strong near‐UV absorption

Near‐UV excited narrow line red‐emitting phosphors, Eu³⁺‐activated Y₂MoO₆ systems, were synthesized using a simple molten salt reaction. The structure and photoluminescence characteristics were investigated using X‐ray powder diffraction, UV–Vis absorption and fluorescent spectrophotometry. The excitation spectra show strong broad‐band absorptions in the near‐UV to blue light regions which match the radiation of near‐UV light‐emitting diode chips well. Under excitation of either near‐UV or blue light, intense red emission with a main peak of 611 nm is observed, ascribed to the ⁵D₀–⁷F₂ transition of Eu³⁺ ions; the optimal doping concentration is 20 mol%. The chromaticity coordinates (x = 0.65, y = 0.34) of the as‐obtained phosphor are very close to the National Television Standard Committee standard values (x = 0.67, y = 0.33). All these characteristics suggest that this material is a promising red‐emitting phosphor candidate for white‐LEDs based on near‐UV LED chips. Copyright © 2012 John Wiley & Sons, Ltd.     

Luminescence properties of red‐emission Mg4Nb2O9:Eu3+ phosphor

Red‐emitting Mg₄Nb₂O₉:Eu³⁺ phosphor is synthesized via a solid‐state reaction method in air, and its crystal structure and luminescence are investigated. The phosphor can be excited efficiently by ~ 395 nm light, coupled well with a ~ 395 nm near‐ultraviolet chip and emits red light at ~ 613 nm with sharp spectra due to ⁵D₀ → ⁷ F₂ transition of the Eu³⁺ ion. Mg₄Nb₂O₉:Eu³⁺ phosphor sintered at 1350 ºC shows Commission international de I'Eclairage (CIE) chromaticity coordinates of x = 0.6354, y = 0.3592, and is a potential red‐emitting phosphor candidate for white light‐emitting diodes (W‐LEDs) under ~ 395 nm near‐ultraviolet LED chip excitation. Copyright © 2014 John Wiley & Sons, Ltd.     

Luminescent properties of novel red‐emitting M7Sn(PO4)6:Eu3+ (M = Sr,Ba) for light‐emitting diodes

Novel red‐emitting phosphors, Eu³⁺‐activated M₇Sn(PO₄)₆ (M = Sr, Ba), were synthesized at 1200°C by conventional solid‐state reaction method. The luminescent properties of M₇Sn(PO₄)₆:Eu³⁺ (M = Sr, Ba) phosphors were investigated, and the critical concentration of the activator (Eu³⁺) concentration were found to be 0.175 mol and 0.21 mol per formula unit for Sr_7‐xSn(PO₄)₆:xEu³⁺ and Ba_7‐xSn(PO₄)₆:xEu³⁺, respectively. These phosphors presented red luminescence under the excitation of 395 or 465 nm, perfectly matching with the emissions wavelength of near‐ultraviolet (UV) light‐emitting diodes (LEDs) and InGaN blue LED.     

The luminescence properties of Sr2–1.5x−1.5yP2O7:xDy3+,yCe3+ phosphor for near‐UV‐based white LEDs synthesized by a chemical co‐precipitation method

A series of Sr₂P₂O₇:Dy³⁺, Sr₂P₂O₇:Ce³⁺ and Sr₂P₂O₇:Dy³⁺,Ce³⁺ phosphors was synthesized via the one‐step calcination process for the precursors prepared by co‐precipitation methods. The phases, morphology, quantum efficiency and photoluminescence properties of the obtained phosphors were characterized systematically. These results show that the near‐spherical particles prepared through calcining the precursors by means of ammonium dibasic phosphate co‐precipitation (method 3) have the smallest particle size and strongest emission intensity among the three methods in the paper. With Dy³⁺ concentration increasing in Sr₂P₂O₇:Dy³⁺ phosphors, the luminescence intensity first increases, reaches maximum, and then decreases. A similar trend was followed by Sr₂P₂O₇:Ce³⁺ with Ce³⁺concentration increasing. A successful attempt was made to initiate the energy transfer mechanism from Ce³⁺ to Dy³⁺ in the host lattice and an overlap between the emission band of Ce³⁺ and the excitation band of Dy³⁺ indicated that the Ce³⁺ → Dy³⁺ energy transfer may indeed exist. It is clear that the photoluminescence intensity of Dy³⁺ as well as the quantum efficiency of the phosphor can be enhanced markedly by co‐doping Ce³⁺. Sr₂P₂O₇:Dy³⁺,Ce³⁺ has its (CIE) chromaticity coordinates in the bluish‐white‐light region, near the standard illuminant D₆₅. The CIE 1913 chromaticity coordinates of Sr₂P₂O₇:Dy³⁺ phosphors fall in the white‐light region, and are adjacent to the ideal white‐light coordinates. In addition, the colour temperature and colour tone of Sr₂P₂O₇:Dy³⁺ could be adjusted by changing the relative concentration of Dy³⁺. In short, Sr₂P₂O₇:Dy³⁺ can be a promising single‐phased white‐light emitting phosphor for near‐UV (NUV) w‐LEDs.     

Enhancement of the photoluminescence and long afterglow properties of Sr2MgSi2O7:Eu2+ phosphor by Dy3+ co‐doping

Sr₂MgSi₂O₇:Eu²⁺ and Sr₂MgSi₂O₇:Eu²⁺,Dy³⁺ long afterglow phosphors were synthesized under a weak reducing atmosphere by the traditional high temperature solid state reaction method. The synthesized phosphors were characterized by powder X‐ray diffraction (XRD), energy dispersive X‐ray spectroscopy (EDX), and photo‐, thermo‐ and mechanoluminescence spectroscopic techniques. The phase structure of the sintered phosphor was an akermanite type structure, which belongs to tetragonal crystallography. The thermoluminescence properties of these phosphors were investigated and compared. Under ultraviolet light excitation, the emission spectra of both prepared phosphors were composed of a broad emission band peaking at 470 nm. When the Sr₂MgSi₂O₇:Eu²⁺ phosphor was co‐doped with Dy³⁺, the photoluminescence (PL), afterglow and mechanoluminescence (ML) intensity were strongly enhanced. The decay graph indicated that both the sintered phosphors contained fast decay and slow decay processes. The ML intensities of Sr₂MgSi₂O₇:Eu²⁺ and Sr₂MgSi₂O₇:Eu²⁺,Dy³⁺ phosphors were increased proportionally with increasing impact velocity, a finding that suggests that these phosphors could be used as sensors to detect the stress of an object. Copyright © 2015 John Wiley & Sons, Ltd.     

Microwave‐assisted sintering synthesis of greenish‐yellow emitting Sr2SiO4:Eu2+ phosphors

Europium ion (Eu²⁺) doped Sr₂SiO₄ phosphors with greenish‐yellow emission were synthesized using microwave‐assisted sintering. The phase structure and photoluminescence (PL) properties of the obtained phosphor samples were investigated. The PL excitation spectra of the Sr₂SiO₄:Eu²⁺ phosphors exhibited a broad band in the range of 260 nm to 485 nm with a maximum at 361 nm attributed to the 5f‐4d allowed transition of the Eu²⁺ ions. Under an excitation at 361 nm, the Sr₂SiO₄:Eu²⁺ phosphor exhibited a greenish‐yellow emission peak at 541 nm with an International‐Commission‐on‐Illumination (CIE) chromaticity of (0.3064, 0.4772). The results suggest that the microwave‐assisted sintering method is promising for the synthesis of phosphors owing to the decreased sintering time without the use of additional reductive agents.     

Synthesis of novel Dy3+ activated Ba2CaZn2Si6O17 phosphors for white light‐emitting diodes

Dysprosium ion (Dy³⁺) activated Ba₂CaZn₂Si₆O₁₇ phosphors were synthesized using high temperature solid‐state reaction method. Powder X‐ray diffraction (PXRD) analysis confirmed the phase formation of the as‐prepared phosphors. Scanning electron microscopy (SEM) analysis disclosed an agglomeration of particles with an irregular morphology. Under 350 nm excitation, the emission spectrum of Dy³⁺ ions showed bands at 481 nm (blue), 577 nm (yellow) and 674 nm (red). The influence of the Dy³⁺ concentration on its emission intensity was investigated. The optimum concentration of Dy³⁺ ions in the Ba₂CaZn₂Si₆O₁₇:Dy³⁺ phosphors were found to be x = 0.06. The critical energy transfer distance was calculated. The fluorescence lifetime was also determined for Ba₂CaZn₂Si₆O₁₇:0.06Dy³⁺. The Commission International deI’Eclairage (CIE) chromaticity coordinates of the phosphor were calculated to be x = 0.304, y = 0.382. The activation energy for the thermal quenching was calculated to be 0.168 eV. These results indicated that the Ba₂CaZn₂Si₆O₁₇:Dy³⁺ phosphor might be a potential candidate for near ultraviolet (NUV)‐based white light‐emitting diodes.     

A new Pr3+‐activated molybdate‐based phosphor for application to white LEDs with blue excitation

The novel red‐emitting phosphors K_xSr_1?2xMoO₄:Pr³⁺_x (0.00 ≤ x ≤ 0.04) were prepared by solid‐state reaction. The crystallization and particle sizes of samples were investigated by powder X‐ray diffraction (XRD) and transmission electron microscopy (TEM). TEM images were in good agreement with the theoretical calculation data from the XRD patterns. Photoluminescence analysis indicated that there were three excitation peaks under 430–500 nm, and all samples showed the intensely red emission at 648 nm corresponding to the ³P₀ → ³F₂ transition of Pr³⁺. The concentrations of doping ions, temperature and polyethylene glycol in the phosphor system can significantly influence the intensity of the red emission. The photoluminescence spectral intensity reached its maximum at x = 0.02. The results showed that the investigated phosphor is a potential red phosphor for white light‐emitting diodes. Copyright © 2010 John Wiley & Sons, Ltd.     

Persistent luminescence of CaMgSi2O6:Eu2+,Dy3+ and CaMgSi2O6:Eu2+,Ce3+ phosphors prepared using the solid‐state reaction method

CaMgSi₂O₆:Eu²⁺,Dy³⁺ and CaMgSi₂O₆:Eu²⁺,Ce³⁺ phosphors were synthesized using the solid‐state reaction method. X‐Ray diffraction (XRD) and photoluminescence (PL) analyses were used to characterize the phosphors. The XRD results revealed that the synthesized CaMgSi₂O₆:Eu²⁺,Dy³⁺ and CaMgSi₂O₆:Eu²⁺,Ce³⁺ phosphors were crystalline and are assigned to the monoclinic structure with a space group C2/c. The calculated crystal sizes of CaMgSi₂O₆:Eu²⁺,Dy³⁺ and CaMgSi₂O₆:Eu²⁺,Ce³⁺ phosphors with a main (221) diffraction peak were 44.87 and 53.51 nm, respectively. Energy‐dispersive X‐ray spectroscopy (EDX) confirmed the proper preparation of the sample. The PL emission spectra of CaMgSi₂O₆:Eu²⁺,Dy³⁺ and CaMgSi₂O₆:Eu²⁺,Ce³⁺ phosphors have a broad band peak at 444.5 and 466 nm, respectively, which is due to electronic transition from 4f⁶5d¹ to 4f⁷. The afterglow results indicate that the CaMgSi₂O₆:Eu²⁺,Dy³⁺ phosphor has better persistence luminescence than the CaMgSi₂O₆:Eu²⁺,Ce³⁺ phosphor. Copyright © 2015 John Wiley & Sons, Ltd.     

Combustion synthesis of blue‐emitting submicron CaAl4O7:Eu2+, Dy3+ persistence phosphor

Long persistence phosphor CaAl₄O₇: Eu²⁺, Dy³⁺ were prepared by a combustion method. The phosphors were characterized by means of X‐ray diffraction (XRD), scanning electron microscopy (SEM), decay time measurement techniques and photoluminescence spectra (PL). The CaAl₄O₇: Eu²⁺, Dy³⁺ phosphor showed a broad blue emission, peaking at 445 nm when excited at 341 nm. Such a blue emission can be attributed to the intrinsic 4f → 5d transitions of Eu²⁺ in the host lattices. The lifetime decay curve of the Dy³⁺ co‐doped CaAl₄O₇: Eu²⁺ phosphor contains a fast decay component and another slow decay one. Surface morphology also has been studied by SEM. The calculated CIE colour chromaticity coordinates was (0.227, 043). We have also discussed a possible long‐persistent mechanism of CaAl₄O₇:Eu²⁺, Dy³⁺ phosphor. All the results indicate that this phosphor has promising potential for practical applications in the field of long‐lasting phosphors for the purposes of sign boards and defence. Copyright © 2011 John Wiley & Sons, Ltd.     

Photoluminescence properties of LiBaPO4:M3+ phosphor for near‐UV light‐emitting diode (M = Eu and Dy)

A novel phosphor LiBaPO₄ doped with rare earths Eu and Dy prepared by high temperature solid‐state reaction method is reported. The phosphors were characterized by X‐ray powder diffraction (XRD), scanning electron microscopy (SEM) and photoluminescence (PL). The emission and excitation spectra of these materials were measured at room temperature with a spectrofluorophotometer. The excitation spectra of LiBaPO₄:Eu³⁺ phosphor can be efficiently excited by 394 nm, which is matched well with the emission wavelength of near‐UV light‐emitting diode (LED) chip. PL properties of Eu³⁺‐doped LiBaPO₄ exhibited the characteristic red emission coming from ⁵D₀ → ⁷ F₁ (593 nm) and ⁵D₀ → ⁷ F₂ (617 nm) electronic transitions with color co‐ordinations of (0.680, 0.315). The results demonstrated that LiBaPO₄:Eu³⁺ is a potential red‐emitting phosphor for near‐UV LEDs. Emission spectra of LiBaPO₄:Dy³⁺ phosphors showed efficient blue (481 nm) and yellow (574 nm) bands, which originated from ⁴ F_9/2 → ⁶H_15/2 and ⁴ F_9/2 → ⁶H_13/2 transitions of the Dy³⁺ ion, respectively. The 574 nm line is more intense than the 481 nm lines, which indicates that the site Dy³⁺ is located with low symmetry. This article summarizes fundamentals and possible applications of optically useful inorganic phosphates with visible photoluminescence of Eu³⁺ and Dy³⁺ ions. Copyright © 2015 John Wiley & Sons, Ltd.     

Synthesis and luminescence of Eu3+‐doped in triple phosphate Ca8MgBi(PO4)7 with whitlockite structure

Triple whitlockite‐type structure‐based red phosphors Ca₈MgBi_1?x(PO₄)₇:xEu³⁺ (x = 0.10, 0.20, 0.30, 0.40, 0.50, 0.60, 0.70, 0.80 and 1.00) were synthesized by a conventional solid‐state reaction route and characterized by their X‐ray crystal structures. The X‐ray diffraction (XRD) patterns, Fourier transform infrared spectra, morphologies, photoluminescence spectra, UV/Vis reflectance spectra, decay times and the International Commission on Illumination (CIE) chromaticity coordinates of Ca₈MgBi_1?x(PO₄)₇:xEu³⁺ were analyzed. Eu‐doped Ca₈MgBi(PO₄)₇ phosphors exhibited strong red luminescence with peaks at 616 nm due to the ⁵D₀ → ⁷ F₂ electric dipole transition of Eu³⁺ ions after excitation at 396 nm. The UV/Vis spectra indicated that the band gap of Ca₈MgBi_0.30(PO₄)₇:0.70Eu³⁺ is larger than that of Ca₈MgBi(PO₄)₇. The phosphor developed in this study has great potential as a red‐light‐emitting phosphor for UV light‐emitting diodes. Copyright © 2015 John Wiley & Sons, Ltd.