Integrated production of lactic acid and biomass on distillery stillage

The possibilities of parallel lactic acid and biomass production in batch and fed-batch fermentation on distillery stillage from bioethanol production were studied. The highest lactic acid yield and productivity of 92.3 % and 1.49 g L^?1 h^?1 were achieved in batch fermentation with initial sugar concentration of 55 g L^?1. A significant improvement of the process was achieved in fed-batch fermentation where the concentration of lactic acid was increased to 47.6 % and volumetric productivity for 21 % over the batch process. A high number of Lactobacillus rhamnosus ATCC 7469 viable cells of 10⁹ CFU ml^?1 was attained at the end of fed-batch fermentation. The survival of 92.9 % of L. rhamnosus cells after 3 h of incubation at pH 2.5 validated that the fermentation media remained after lactic acid removal could be used as a biomass-enriched animal feed thus making an additional value to the process.     

Effects of neutralizing agents on lactic acid production by Rhizopus oryzae using sweet potato starch

A neutralizing agent is usually employed to counteract the pH reduction during lactic acid fermentation by Rhizopus oryzae. Calcium carbonate (CaCO₃) is used as such a pH controlling agent. The low solubility of CaCO₃ in the fermentation broth could however lead to low efficiency in pH control and cause problems in the subsequent purification process. Therefore, an alternative agent in place of CaCO₃ was examined in this study. The effect of four different neutralizing agents, including CaCO₃, sodium hydroxide (NaOH), ammoniacal solution and sodium bicarbonate (NaHCO₃) on lactic acid production and the morphology of the pellets were investigated. Results indicated that CaCO₃ was still the preferred choice, because of the pellet morphology and the highest lactic acid concentration (43.3 g/L) obtained in the batch using 60 g/L of sweet potato starch as feedstock. It is noteworthy that the lactic acid purification is relatively easier when using NaHCO₃ instead of CaCO₃, due to the higher solubility of sodium lactate than calcium lactate. Therefore, even the batch with CaCO₃ had a slightly higher productivity (1.23 g/L/h) than the batch with NaHCO₃ (1.14 g/L/h), NaHCO₃ might be the first choice for process designers whenever recovery is vital.     

A novel isolate of <Emphasis Type="Italic">Clostridium butyricum</Emphasis> for efficient butyric acid production by xylose fermentation

Bacterial fermentation of lignocellulose has been regarded as a sustainable approach to butyric acid production. However, the yield of butyric acid is hindered by the conversion efficiency of hydrolysate xylose. A mesophilic alkaline-tolerant strain designated as Clostridium butyricum B10 was isolated by xylose fermentation with acetic and butyric acids as the principal liquid products. To enhance butyric acid production, performance of the strain in batch fermentation was evaluated with various temperatures (20–47 °C), initial pH (5.0–10.0), and xylose concentration (6–20 g/L). The results showed that the optimal temperature, initial pH, and xylose concentration for butyric acid production were 37 °C, 9.0, and 8.00 g/L, respectively. Under the optimal condition, the yield and specific yield of butyric acid reached about 2.58 g/L and 0.36 g/g xylose, respectively, with 75.00% butyric acid in the total volatile fatty acids. As renewable energy, hydrogen was also collected from the xylose fermentation with a yield of about 73.86 mmol/L. The kinetics of growth and product formation indicated that the maximal cell growth rate (μ _m ) and the specific butyric acid yield were 0.1466 h^?1 and 3.6274 g/g cell (dry weight), respectively. The better performance in xylose fermentation showed C. butyricum B10 a potential application in efficient butyric acid production from lignocellulose.     

Effective conversion of industrial starch waste to L-Lactic acid by Lactococcus lactis in a dialysis sac bioreactor

We describe here a simple technological process based on the direct fermentation of potato starch waste (PSW), an inexpensive agro-processing industrial waste, by a potential probiotic strain, Lactococcus lactis subsp. lactis, for enhancing L-lactic acid production. To maximize bioconversion and increase cell stability, we designed and tested a novel dialysis sac-based bioreactor. Shake flask fermentation (SFF) and fed batch fermentation in the dialysis sac bioreactor were compared for L-lactic acid production efficiency. The results showed that the starch (20 g/L) in the PSW-containing medium was completely consumed within 24 h in the dialysis sac bioreactor, compared with 48 h in the SFF. The maximum lactic acid concentration (18.9 g/L) and lactic acid productivity (0.79 g/L·h) obtained was 1.2- and 2.4-fold higher in the bioreactor than by SFF, respectively. Simultaneous saccharification and fermentation was effected at pH 5.5 and 30 °C. L. lactis cells were viable for up to four cycles in the fed batch fermentation compared to only one cycle in the SFF.     

Characterization of ethanol fermentation waste and its application to lactic acid production by Lactobacillus paracasei

In this study, an ethanol fermentation waste (EFW) was characterized for use as an alternative to yeast extract for bulk fermentation processes. EFW generated from a commercial plant in which ethanol is produced from cassava/rice/wheat/barley starch mixtures using Saccharomyces cerevisiae was used for lactic acid production by Lactobacillus paracasei. The effects of temperature, pH, and duration on the autolysis of an ethanol fermentation broth (EFB) were also investigated. The distilled EFW (DEFW) contained significant amounts of soluble proteins (2.91 g/l), nitrogen (0.47 g/l), and amino acids (24.1 mg/l). The autolysis of the EFB under optimum conditions released twice as much amino acids than in the DEFW. Batch fermentation in the DEFW increased the final lactic acid concentration, overall lactic acid productivity, and lactic acid yield on glucose by 17, 41, and 14 %, respectively, in comparison with those from comparable fermentation in a lactobacillus growth medium (LGM) that contained 2 g/l yeast extract. Furthermore, the overall lactic acid productivity in the autolyzed then distilled EFW (ADEFW) was 80 and 27 % higher than in the LGM and DEFW, respectively.     

Efficient production of l-lactic acid by newly isolated thermophilic Bacillus coagulans WCP10-4 with high glucose tolerance

A thermophilic Bacillus coagulans WCP10-4 with tolerance to high concentration of glucose was isolated from soil and used to produce optically pure l-lactic acid from glucose and starch. In batch fermentation at pH?6.0, 240 g/L of glucose was completely consumed giving 210 g/L of l-lactic acid with a yield of 95 % and a productivity of 3.5 g/L/h. In simultaneous saccharification and fermentation at 50 °C without sterilizing the medium, 200 g/L of corn starch was completely consumed producing 202.0 g/L of l-lactic acid. To the best of our knowledge, this strain shows the highest osmotic tolerance to glucose among the strains ever reported for lactic acid production. This is the first report of simultaneous saccharification and fermentation of starch for lactic acid production under a non-sterilized condition.     

Enhancement and modeling of microparticle-added <Emphasis Type="Italic">Rhizopus oryzae</Emphasis> lactic acid production

Lactic acid has a wide industrial application area and can be produced by fungal strains. However, excessive bulk growth form of fungi during the fermentations is a major problem, which limits the fermentation performance. Microparticles are excellent tools to prevent bulk fungal growth and provide homogenized fermentation broth to increase uniformity and the prediction performance of the models. Therefore, in this study, addition of aluminum oxide and talcum microparticles into fermentations was evaluated to enhance the production of lactic acid by Rhizopus oryzae. The results showed that the bulk fungal growth was prevented and the lactic acid concentration increased from 6.02 to 13.88 and 24.01 g/L, when 15 g/L of aluminum oxide or 10 g/L of talcum was used, respectively, in the shake-flask fermentations. Additionally, substrate concentration, pH, and agitation were optimized in the bioreactors using response surface methodology, and optimum values were determined as 126 g/L of glucose, 6.22 pH, and 387 rpm, respectively. Under these conditions, lactic acid production further increased to 75.1 ± 1.5 g/L with 10 g/L of talcum addition. Also, lactic acid production and glucose consumption in the batch fermentation were successfully modeled with modified Gompertz model and modified logistic model. RMSE and MAE values for lactic acid production were calculated as 2.279 and 1.498 for the modified Gompertz model; 3.6 and 4.056 for the modified logistic model. Additionally, modified logistic model predicted glucose consumption with ?2.088 MAE and 2.868 RMSE, whereas these values were calculated as 2.035 and 3.946 for the modified Gompertz model.     

Microbial production of a biofuel (acetone–butanol–ethanol) in a continuous bioreactor: impact of bleed and simultaneous product removal

Acetone butanol ethanol (ABE) was produced in an integrated continuous one-stage fermentation and gas stripping product recovery system using Clostridium beijerinckii BA101 and fermentation gases (CO₂ and H₂). In this system, the bioreactor was fed with a concentrated sugar solution (250–500 g L^?1 glucose). The bioreactor was bled semi-continuously to avoid accumulation of inhibitory chemicals and products. The continuous system was operated for 504 h (21 days) after which the fermentation was intentionally terminated. The bioreactor produced 461.3 g ABE from 1,125.0 g total sugar in 1 L culture volume as compared to a control batch process in which 18.4 g ABE was produced from 47.3 g sugar. These results demonstrate that ABE fermentation can be operated in an integrated continuous one-stage fermentation and product recovery system for a long period of time, if butanol and other microbial metabolites in the bioreactor are kept below threshold of toxicity.     

Inhibition of yeast by lactic acid bacteria in continuous culture: nutrient depletion and/or acid toxicity?

Lactic acid was added to batch very high gravity (VHG) fermentations and to continuous VHG fermentations equilibrated to steady state with Saccharomyces cerevisiae. A 53% reduction in colony-forming units (CFU) ml^–1 of S. cerevisiae was observed in continuous fermentation at an undissociated lactic acid concentration of 3.44% w/v; and greater than 99.9% reduction was evident at 5.35% w/v lactic acid. The differences in yeast cell number in these fermentations were not due to pH, since batch fermentations over a pH range of 2.5–5.0 did not lead to changes in growth rate. Similar fermentations performed in batch showed that growth inhibition with added lactic acid was nearly identical. This indicates that the apparent high resistance of S. cerevisiae to lactic acid in continuous VHG fermentations is not a function of culture mode. Although the total amount of ethanol decreased from 48.7 g l^–1 to 14.5 g l^–1 when 4.74% w/v undissociated lactic acid was added, the specific ethanol productivity increased ca. 3.2-fold (from 7.42×10^–7 g to 24.0×10^–7 g ethanol CFU^–1 h^–1), which indicated that lactic acid stress improved the ethanol production of each surviving cell. In multistage continuous fermentations, lactic acid was not responsible for the 83% (CFU ml^–1) reduction in viable S. cerevisiae yeasts when Lactobacillus paracasei was introduced to the system at a controlled pH of 6.0. The competition for trace nutrients in those fermentations and not lactic acid produced by L. paracasei likely caused the yeast inhibition.     

Substrate and product inhibition kinetics in succinic acid production by Actinobacillus succinogenes

The inhibition of substrate and products on the growth of Actinobacillus succinogenes in fermentation using glucose as the major carbon source was studied. A. succinogenes tolerated up to 143 g/L glucose and cell growth was completely inhibited with glucose concentration over 158 g/L. Significant decrease in succinic acid yield and prolonged lag phase were observed with glucose concentration above 100 g/L. Among the end-products investigated, formate was found to have the most inhibitory effect on succinic acid fermentation. The critical concentrations of acetate, ethanol, formate, pyruvate and succinate were 46, 42, 16, 74, 104 g/L, respectively. A growth kinetic model considering both substrate and product inhibition is proposed, which adequately simulates batch fermentation kinetics using both semi-defined and wheat-derived media. The model accurately describes the inhibitory kinetics caused by both externally added chemicals and the same chemicals produced during fermentation. This paper provides key insights into the improvement of succinic acid production and the modelling of inhibition kinetics.     

Improved n-butanol production by a non-acetone producing Clostridium pasteurianum DSMZ 525 in mixed substrate fermentation

The kinetics of growth, acid and solvent production in batch culture of Clostridium pasteurianum DSMZ 525 were examined in mixed or mono-substrate fermentations. In pH-uncontrolled batch cultures, the addition of butyric acid or glucose significantly enhanced n-butanol production and the ratio of butanol/1,3-propanediol. In pH-controlled batch culture at pH?=?6, butyric acid addition had a negative effect on growth and did not lead to a higher n-butanol productivity. On the other hand, mixed substrate fermentation using glucose and glycerol enhanced the growth and acid production significantly. Glucose limitation in the mixed substrate fermentation led to the reduction or inhibition of the glycerol consumption by the growing bacteria. Therefore, for the optimal growth and n-butanol production by C. pasteurianum, a limitation of either substrate should be avoided. Under optimized batch conditions, n-butanol concentration and maximum productivity achieved were 21 g/L, and 0.96 g/L?×?h, respectively. In comparison, mixed substrate fermentation using biomass hydrolysate and glycerol gave a n-butanol concentration of 17 g/L with a maximum productivity of 1.1 g/L?×?h. In terms of productivity and final n-butanol concentration, the results demonstrated that C. pasteurianum DSMZ 525 is well suitable for n-butanol production from mixed substrates of biomass hydrolysate and glycerol and represents an alternative promising production strain.     

Conversion of acid hydrolysate of oil palm empty fruit bunch to L-lactic acid by newly isolated Bacillus coagulans JI12

Cost-effective conversion of lignocellulose hydrolysate to optically pure lactic acid is commercially attractive but very challenging. Bacillus coagulans JI12 was isolated from natural environment and used to produce L-lactic acid (optical purity?>?99.5 %) from lignocellulose sugars and acid hydrolysate of oil palm empty fruit bunch (EFB) at 50 °C and pH 6.0 without sterilization of the medium. In fed-batch fermentation with 85 g/L initial xylose and 55 g/L xylose added after 7.5 h, 137.5 g/L lactic acid was produced with a yield of 98 % and a productivity of 4.4 g/L?h. In batch fermentation of a sugar mixture containing 8.5 % xylose, 1 % glucose, and 1 % L-arabinose, the lactic acid yield and productivity reached 98 % and 4.8 g/L?h, respectively. When EFB hydrolysate was used, 59.2 g/L of lactic acid was produced within 9.5 h at a yield of 97 % and a productivity of 6.2 g/L?h, which are the highest among those ever reported from lignocellulose hydrolysates. These results indicate that B. coagulans JI12 is a promising strain for industrial production of L-lactic acid from lignocellulose hydrolysate.     

Bio-ethanol Production from Green Onion by Yeast in Repeated Batch

Considered to be the cleanest liquid fuel, bio-ethanol can be a reliable alternative to fossil fuels. It is produced by fermentation of sugar components of plant materials. The common onions are considered to be a favorable source of fermentation products as they have high sugar contents as well as contain various nutrients. This study focused on the effective production of ethanol from Green onion (Allium fistulosum L.) by the yeast “Saccharomyces cerevisiae” in repeated batch. The results showed that the total sugar concentration of onion juice was 68.4 g/l. The maximum rate of productivity, ethanol yield and final bio-ethanol percentage was 7 g/l/h (g ethanol per liter of onion juice per hour), 35 g/l (g ethanol per liter of onion juice) and 90 %, respectively.     

Growth conditions of clostridium perfringens type B for production of toxins used to obtain veterinary vaccines

The diseases caused for Clostridium perfringens are generically called enterotoxemias because toxins produced in the intestine may be absorbed into the general circulation. C. perfringens type B, grown in batch fermentation, produced toxins used to obtain veterinary vaccines. Glucose in concentrations of 1.4–111.1 mM was used to define the culture medium. The minimum concentration for a satisfactory production of vaccines against clostridial diseases was 55.6 mM. Best results were brought forth by meat and casein peptones, both in the concentration 5.0 g l^?1 in combination with glucose and a culture pH maintained at 6.5 throughout the fermentation process. The production of lactic, acetic and propionic organic acids was observed. Ethanol was the metabolite produced in the highest concentration when cultures maintained steady pH of 6.5 with exception of cultures with initial glucose concentration of 1.4 mM, where the highest production was of propionic acid. Maximal cell concentration and the highest toxin title concomitantly low yield coefficient to organic acids and ethanol were obtained using basal medium containing 111.1 mM glucose under a controlled pH culture (pH) 6.5 in batch fermentations of C. perfringens type B. These data contribute to improve process for industrial toxin production allowing better condition to produce a toxoid vaccine.     

Ethanol production from galactose by a newly isolated Saccharomyces cerevisiae KL17

A wild-type yeast strain with a good galactose-utilization efficiency was newly isolated from the soil, and identified and named Saccharomyces cerevisiae KL17 by 18s RNA sequencing. Its performance of producing ethanol from galactose was investigated in flask cultures with media containing various combination and concentrations of galactose and glucose. When the initial galactose concentration was 20 g/L, it showed 2.2 g/L/h of substrate consumption rate and 0.63 g/L/h of ethanol productivity. Although they were about 70 % of those with glucose, such performance of S. cerevisiae KL17 with galactose was considered to be quite high compared with other strains reported to date. Its additional merit was that its galactose metabolism was not repressed by the existence of glucose. Its capability of ethanol production under a high ethanol concentration was demonstrated by fed-batch fermentation in a bioreactor. A high ethanol productivity of 3.03 g/L/h was obtained with an ethanol concentration and yield of 95 and 0.39 g/L, respectively, when the cells were pre-cultured on glucose. When the cells were pre-cultured on galactose instead of glucose, fermentation time could be reduced significantly, resulting in an improved ethanol productivity of 3.46 g/L/h. The inhibitory effects of two major impurities in a crude galactose solution obtained from acid hydrolysis of galactan were assessed. Only 5-Hydroxymethylfurfural (5-HMF) significantly inhibited ethanol fermentation, while levulinic acid (LA) was benign in the range up to 10 g/L.     

Production of succinic acid and lactic acid by Corynebacterium crenatum under anaerobic conditions

A new succinic acid and lactic acid production bioprocess by Corynebacterium crenatum was investigated in mineral medium under anaerobic conditions. Corynebacterium crenatum cells with sustained acid production ability and high acid volumetric productivity harvested from the glutamic acid fermentation broth were used to produce succinic acid and lactic acid. Compared with the first cycle, succinic acid production in the third cycle increased 120% and reached 43.4 g/L in 10 h during cell-recycling repeated fermentations. The volumetric productivities of succinic acid and lactic acid could maintain above 4.2 g/(L·h) and 3.1 g/(L·h), respectively, for at least 100 h. Moreover, wheat bran hydrolysates could be used for succinic acid and lactic acid production by the recycled C. crenatum cells. The final succinic acid concentration reached 43.6 g/L with a volumetric productivity of 4.36 g/(L·h); at the same time, 32 g/L lactic acid was produced.     

Ethanol effect on batch and fed-batch Arthrospira platensis growth

The ability of Arthrospira platensis to use ethanol as a carbon and energy source was investigated by batch process and fed-batch process. A. platensis was cultivated under the effect of a single addition (batch process) and a daily pulse feeding (fed-batch process) of pure ethanol, at different concentrations, to evaluate cell concentration (X) and specific growth rate (μ). A marked increase was observed in the cell concentration of A. platensis in runs with ethanol addition when compared to control cultures without ethanol addition. The fed-batch process using an ethanol concentration of 38 mg L^?1 days^?1 reached the maximum cell concentration of 2,393 ± 241 mg L^?1, about 1.5-fold that obtained in the control culture. In all experiments, the maximum specific growth rate was observed in the early exponential phase of cell growth. In the fed-batch process, μ decreased more slowly than in the batch process and control culture, resulting in the highest final cell concentration. Ethanol can be used as a feasible carbon and energy source for A. platensis growth via a fed-batch process.     

An oxidoreduction potential shift control strategy for high purity propionic acid production by Propionibacterium freudenreichii CCTCC M207015 with glycerol as sole carbon source

The effects of oxidoreduction potential (ORP) regulation on the process of propionic acid production by Propionibacterium freudenreichii CCTCC M207015 have been investigated. Potassium ferricyanide and sodium borohydride were determined as ORP control agents through serum bottle experiment. In batch fermentation, cell growth, propionic acid and by-products distribution were changed with ORP levels in the range of 0–160 mV. Based on these analysis results, an ORP-shift control strategy was proposed: at first 156 h, ORP was controlled at 120 mV to obtain higher cell growth rate and propionic acid formation rate, and then it was shifted to 80 mV after 156 h to maintain the higher propionic acid formation rate. By applying this strategy, the optimal parameters were obtained as follows: the propionic acid concentration 45.99 g L^?1, productivity 0.192 g L^?1 h^?1, the proportion of propionic acid to total organic acids 92.26 % (w/w) and glycerol conversion efficiency 76.65 %. The mechanism of ORP regulation was discussed by the ratio of NADH/NAD⁺, ATP levels, and metabolic flux analysis. The results suggest that it is possible to redistribute energy and metabolic fluxes by the ORP-shift control strategy, and the strategy could provide a simple and efficient tool to realize high purity propionic acid production with glycerol as carbon source.     

Kinetics and Modeling of Lactic Acid Production by Lactobacillus plantarum

An unstructured model was developed to describe bacterial growth, substrate utilization, and lactic acid production by Lactobacillus plantarum in cucumber juice. Significant lactic acid production occurred during growth, as well as stationary phases. The percentage of acid produced after growth ceased was a function of the medium composition. Up to 51% of the lactic acid was produced after growth ceased when NaCl was not present in the medium, whereas not more than 18% of the total lactic acid was produced after the growth ceased in presence of NaCl, probably because of an increase in the cell death rate. An equation relating the specific death rate and NaCl concentration was developed. With the kinetic model proposed by R. Luedeking and E. L. Piret (J. Biochem. Microbiol. Technol. Eng. 1:393-412, 1958) for lactic acid production rate, the growth-associated and non-growth-associated coefficients were determined as 51.9 (±4.2) mmol/g of cells and 7.2 (±0.9) mmol/g of cells h^-1 respectively. The model was demonstrated for batch growth of L. plantarum in cucumber juice. Mathematical simulations were used to predict the influence of variations in death rate, proton concentration when growth ceased, and buffer capacity of the juice on the overall fermentation process.     

Utilization of by-products derived from bioethanol production process for cost-effective production of lactic acid

The by-products of bioethanol production such as thin stillage (TS) and condensed distillers solubles (CDS) were used as a potential nitrogen source for economical production of lactic acid. The effect of those by-products and their concentrations on lactic acid fermentation were investigated using Lactobacillus paracasei CHB2121. Approximately, 6.7 g/L of yeast extract at a carbon source to nitrogen source ratio of 15 was required to produce 90 g/L of lactic acid in the medium containing 100 g/L of glucose. Batch fermentation of TS medium resulted in 90 g/L of lactic acid after 48 h, and the medium containing 10 % CDS resulted in 95 g/L of lactic acid after 44 h. Therefore, TS and CDS could be considered as potential alternative fermentation medium for the economical production of lactic acid. Furthermore, lactic acid fermentation was performed using only cassava and CDS for commercial production of lactic acid. The volumetric productivity of lactic acid [2.94 g/(L·h)] was 37 % higher than the productivity obtained from the medium with glucose and CDS.