Purification and in situ immobilization of lipase from of a mutant of Trichosporon laibacchii using aqueous two-phase systems

The crude intracellular lipase (cell homogenate) from Trichosporon laibacchii was subjected to partial purification by aqueous two-phase system (ATPS) and then in situ immobilization by directly adding diatomites as carrier to the top PEG-rich phase of ATPS. A partition study of lipase in the ATPS formed by polyethylene glycol–potassium phosphate has been performed. The influence of system parameters such as molecular weight of PEG, system phase composition and system pH on the partitioning behaviour of lipase was evaluated. The ATPS consisting of PEG 4000 (12%) and potassium phosphate (K₂HPO₄, 13%) resulted in partition of lipase to the PEG-rich phase with partition coefficient 7.61, activity recovery 80.4%, and purification factor of 5.84 at pH of 7.0 and 2.0% NaCl. Moreover, the in situ immobilization of lipase in PEG phase resulted in a highest immobilized lipase activity of 1114.6 U g^?1. The above results show that this novel lipase immobilization procedure which couples ATPS extract and enzyme immobilization is cost-effective as well as time-saving. It could be potentially useful technique for the purification and immobilization of lipase.     

Isolation of a Aspergillus niger lipase from a solid culture medium with aqueous two-phase systems

The aim of this work is to find the best conditions to isolate lipase from a solid culture medium of Aspergillus niger NRRL3 strains using aqueous two-phase systems formed with polyethylene glycol and potassium phosphate or polyethylene glycol and sodium citrate. We studied the partitioning of a commercial lyophilizate from A. niger. Also, the lipase enzymatic activity was studied in all the phases of the systems and the results indicate that citrate anion increases lipase activity. An analysis by fluorescence spectroscopy of the interaction between lipase and the bottom and top phases of the systems shows that the protein tryptophan-environments are modified by the presence of PEG and salts. Separation of the enzyme from the rest of the proteins that make up the lyophilized was achieved with good yield and separation factor by ATPS formed by PEG 1000/Pi at pH 7, PEG 2000/Ci at pH 5.2 and PEG 4000/Ci at pH 5.2. The above mentioned systems were used in order to isolate extracellular lipase from a strain of A. niger in submerged culture and solid culture. The best system for solid culture, with high purification factor (30.50), is the PEG 4000/Ci at pH 5.2. The enzyme was produced in a solid culture medium whose production is simple and recovered in a phase poor in polymer, bottom phase. An additional advantage is that the citrate produces less pollution than the phosphate. This methodology could be used as a first step for the isolation of the extracellular lipase from A. niger.     

Porcine pancreatic lipase partition in potassium phosphate-polyethylene glycol aqueous two-phase systems

This research study examined porcine pancreatic lipase partition in aqueous two-phase systems formed by polyethylene glycol-potassium phosphate at pH 6.0, 7.0 and 8.0, the effect of polymer molecular mass, and NaCl concentration. The enzyme was preferentially partitioned into the polyethylene glycol rich phase in systems with molecular mass 4000-8000, while with polyethylene glycol of 10,000 molecular mass it was concentrated in the phosphate rich phase. The enthalpic and entropic changes found due to the protein partition were negative for all the polyethylene glycol molecular mass systems assessed. Both thermodynamic functions were shown to be associated by an entropic-enthalpic compensation effect suggesting that the water structure ordered in the ethylene chain of polyethylene glycol plays a role in the protein partition. The addition of NaCl increased the lipase affinity to the top phase and this effect was most significant in the system polyethylene glycol 2000-NaCl 3%. This system yielded an enzyme recovery more than 90% with a purification factor of approximately 3.4.     

Aqueous two-phase extraction for the purification of alkaline agarases from culture extracts of Pseudomonas aeruginosa AG LSL-11

The agarases were purified for the first time an using aqueous two-phase system (ATPS) consisting of polyethylene glycol (PEG) and phosphate salt. The three extracellular, alkaline agarases produced by Pseudomonas aeruginosa AG LSL-11 were efficiently extracted into the top PEG-rich layer. The influencing factors on the partition of agarases--molecular weight of the PEG, system pH, system temperature, and NaCl concentration--were investigated. All the factors were found to have a significant effect on the partition of agarases except NaCl. The optimal ATPS parameters for the partitioning and purification of agarases were found to be 12% PEG 600 and 11.9% (w/w) phosphate salt at pH 8.0 and 4°C. All three agarases were concentrated in the top PEG phase with 6.19-fold purity and 71.21% recovery. The ATPS was found to be more convenient and economical than the conventional ion-exchange chromatography (IEC) method for extraction of three agarases and could be significantly employed for the purification of agarases from fermentation broth.     

Liquid–liquid extraction of an extracellular alkaline protease from fermentation broth using aqueous two-phase and reversed micelles systems

Summary The study of recovery of an extracellular alkaline protease from fermentation broth produced by Norcadiopsis sp, was carried out with liquid–liquid extraction through sodium di-(2-ethylhexyl) sulphosuccinate/isooctane reversed micelles systems and aqueous two-phase systems (polyethylene glycol/potassium phosphate). The best conditions for extraction and back-extraction with the reversed micelles system was obtained at pH 9.0 and pH 5.0, respectively, showing a yield of protein of 6.16%, a specific activity of 4.10 U/ml and a purification factor of 1.80. The studies using aqueous two-phase systems of polyethylene glycol/potassium phosphate at pH 10.0 showed purification factors of 2 and 5, and protein yield of 11 and 4%, respectively, for polyethylene glycol 550/potassium phosphate and polyethylene glycol 8000/potassium phosphate. The results indicate that the aqueous two-phase systems are more attractive as a first step in the isolation and purification processes.     

Recovery of endo-polygalacturonase using polyethylene glycol-salt aqueous two-phase extraction with polymer recycling

The partitioning behaviour of endo-polygalacturonase (endo-PG) and total protein from a clarified Kluyveromyces marxianus fermentation broth in polyethylene glycol (PEG)-ammonium sulfate and PEG-potassium phosphate (pH=7) aqueous two-phase systems was experimentally investigated. Both the enzyme and total protein partitioned in the bottom phase for these two kinds of systems. The enzyme partitioning coefficient can be lower than 0.01 in PEG8000-(NH₄)₂SO₄ ATPS with a large phase volume ratio and a moderate tie-line length, which implies the possibility of concentration operation using aqueous two phase partitioning. An ion-exchange separation of high purification efficiency was applied to analyze the clarified and dialyzed fermentation broth. A total purification factor of only 2.3 was obtained, which indicated the high enzyme protein content in the total protein of the fermentation broth. Consequently, the main purpose for separating endo-PG is concentration rather than purification. A separation scheme using an aqueous two-phase extraction process with polymer recycling and a dialysis was proposed to recover endo-PG from the fermentation supernatant of K. marxianus for commercial purpose. A high enzyme recovery up to 95% and a concentration factor of 5 to 8 with a purification factor of about 1.25 were obtained using the single aqueous two-phase extraction process. More than 95% polymer recycled will not affect the enzyme recovery and purification factor. Dialysis was used mainly to remove salts in the bottom phase. The dialysis step has no enzyme loss and can further remove small bulk proteins. The total purification factor for the scheme is about 1.7.     

Purification and Characterization of Polyphenol Oxidase From Waste Potato Peel by Aqueous Two-Phase Extraction

Potato peel from food industrial waste is a good source of polyphenol oxidase (PPO). This work illustrates the application of an aqueous two-phase system (ATPS) for the extraction and purification of PPO from potato peel. ATPS was composed of polyethylene glycol (PEG) and potassium phosphate buffer. Effect of different process parameters, namely, PEG, potassium phosphate buffer, NaCl concentration, and pH of the system, on partition coefficient, purification factor, and yield of PPO enzyme were evaluated. Response surface methodology (RSM) was utilized as a statistical tool for the optimization of ATPS. Optimized experimental conditions were found to be PEG1500 17.62% (w/w), potassium phosphate buffer 15.11% (w/w), and NaCl 2.08 mM at pH 7. At optimized condition, maximum partition coefficient, purification factor, and yield were found to be 3.7, 4.5, and 77.8%, respectively. After partial purification of PPO from ATPS, further purification was done by gel chromatography where its purity was increased up to 12.6-fold. The purified PPO enzyme was characterized by sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE), followed by K_m value 3.3 mM, and V_max value 3333 U/mL, and enzyme stable ranges for temperature and pH of PPO were determined. These results revealed that ATPS would be an attractive option for obtaining purified PPO from waste potato peel.     

Direct purification of Burkholderia Pseudomallei lipase from fermentation broth using aqueous two-phase systems

An aqueous two-phase purification process was employed for the recovery of Burkholderia pseudomallei lipase from fermentation broth. The partition behavior of B. pseudomallei lipase was investigated with various parameters such as phase composition, tie-line length (TLL), volume ratio (V_R), sample loading, system pH, and addition of neutral salts. Optimum conditions for the purification of lipase were obtained in polyethylene glycol (PEG) 6000-potassium phosphate system using TLL of 42.2% (w/w), with VR of 2.70, and 1% (w/w) NaCl addition at pH 7 for 20% (w/w) crude load. Based on this system, the purification factor of lipase was enhanced to 12.42 fold, with a high yield of 93%. Hence, the simplicity and effectiveness of aqueous two-phase systems (ATPS) in the purification of lipase were proven in this study.     

Extraction of protease from Aspergillus tamarii URM 4634 in aqueous two-phase system under continuous and discontinuous process

Abstract

Aqueous two-phase systems have been studied for almost a century to separate biomolecules in harmless conditions. Proteases produced by Aspergillus tamarii URM 4634 were extracted in polyethylene glycol (PEG)/phosphate aqueous two-phase system under discontinuous and continuous (perforated rotative discs column) process. On the discontinuous process, it was evaluated the effect of operational conditions (PEG molar mass and its concentration, phosphate concentration and pH) over the partition coefficient, activity yield and purification factor. Protease partitioned to PEG-phase with partition coefficients up to 55.73. The best process parameters were 17.5% of PEG, with molar mass 8000?g·mol^?1, 15% of phosphate salt at pH 6, with 113.15% of activity yield and purification factor of 2.62. Under continuous extraction, hold up data showed that 57.1% of the discontinuous phase was available for protein extraction. Further, separation achieved 90.0% of efficiency. The yields surpassed 100% in almost all runs, and the best purification factor was 1.84, with both flows of 2?mL·min^?1. Thus, the best operational conditions reached an activity yield of 95.3% and 90.0% of separation efficiency. Hence, aqueous two-phase system PEG/phosphate extraction is an efficient process for separation of proteases produced by Aspergillus tamarii URM 4634, under continuous extraction likewise under discontinuous process.     

Evaluating aqueous two-phase systems for Yarrowia lipolytica extracellular lipase purification

In this study an aqueous two-phase system (ATPS) composed of polyethylene glycol (PEG) and potassium phosphate was tested for the purification of lipase from Yarrowia lipolytica IMUFRJ 50682. Ultrafiltration and precipitation with acetone and kaolin were also used as traditional comparison methods Ultrafiltration was a good method with a purification factor of 6.55, but protease was also purified in this extract. For the precipitation with acetone and kaolin lower values of lipase and protease activity were found in relation to the original crude enzyme extract. Under the best conditions of ATPS (pH 6 and 4 °C), the purification fold was greater than 40 and selectivity was almost 500. Lipase was recovered in the salty phase which makes it easier to purify it. The optimum pH and temperature ranges for purified lipase with this system was 6–7 and 35–40 °C, respectively. Lipase thermostability was increased in relation to crude extract after the purification with the PEG/phosphate buffer system for temperatures lower than 50 °C. All enzyme extracts showed good stability to a wide pH range. Y. lipolytca lipase was successfully purified by using ATPS in a single downstream processing step and presented good process characteristics after this treatment.     

Purification of recombinant phenylalanine dehydrogenase by partitioning in aqueous two-phase systems

This study presents the partitioning and purification of recombinant Bacillus badius phenylalanine dehydrogenase (PheDH) in aqueous two-phase systems (ATPS) composed of polyethylene glycol 6000 (PEG-6000) and ammonium sulfate. A single-step operation of ATPS was developed for extraction and purification of recombinant PheDH from E. coli BL21 (DE3). The influence of system parameters including; PEG molecular weight and concentration, pH, (NH(4))(2)SO(4) concentration and NaCl salt addition on enzyme partitioning were investigated. The best optimal system for the partitioning and purification of PheDH was 8.5% (w/w) PEG-6000, 17.5% (w/w) (NH(4))(2)SO(4) and 13% (w/w) NaCl at pH 8.0. The partition coefficient, recovery, yield, purification factor and specific activity values were of 92.57, 141%, 95.85%, 474.3 and 10424.97 U/mg, respectively. Also the K(m) values for L-phenylalanine and NAD(+) in oxidative deamination were 0.020 and 0.13 mM, respectively. Our data suggested that this ATPS could be an economical and attractive technology for large-scale purification of recombinant PheDH.     

AQUEOUS TWO-PHASE EXTRACTION FOR THE PURIFICATION OF ALKALINE AGARASES FROM CULTURE EXTRACTS OF Pseudomonas aeruginosa AG LSL-11

The agarases were purified for the first time an using aqueous two-phase system (ATPS) consisting of polyethylene glycol (PEG) and phosphate salt. The three extracellular, alkaline agarases produced by Pseudomonas aeruginosa AG LSL-11 were efficiently extracted into the top PEG-rich layer. The influencing factors on the partition of agarases—molecular weight of the PEG, system pH, system temperature, and NaCl concentration—were investigated. All the factors were found to have a significant effect on the partition of agarases except NaCl. The optimal ATPS parameters for the partitioning and purification of agarases were found to be 12% PEG 600 and 11.9% (w/w) phosphate salt at pH 8.0 and 4°C. All three agarases were concentrated in the top PEG phase with 6.19-fold purity and 71.21% recovery. The ATPS was found to be more convenient and economical than the conventional ion-exchange chromatography (IEC) method for extraction of three agarases and could be significantly employed for the purification of agarases from fermentation broth.     

Production of immobilized penicillin acylase using aqueous polymer systems for enzyme purification and in situ immobilization

A novel approach for the isolation and purification of penicillin acylase (PA), which couples aqueous two-phase partitioning and enzyme immobilization has been investigated.A PA yield of 90% was achieved by treating E. coli cells with 4% butyl acetate, freeze-thawing step, and pressure homogenization. PA purification (93% recovery) was achieved by (1) removing cell debris via precipitation with polyethylene glycol (PEG 2000); (2) aqueous two-phase partitioning using a PEG 2000 + phosphate system (87% recovery).An in situ enzyme immobilization approach, using oxirane acrylic or aldehyde-agarose beads dispersed in the PEG-rich phase, was explored for the conversion of penicillin G to 6-aminopenicillanic acid. An appropriate immobilization reaction time was found. The catalytic performance of the enzyme, when immobilized, was found not to be affected by recycling of the phase-forming components.     

Optimisation of aqueous two-phase extraction of human antibodies

The purification of human antibodies in an aqueous two-phase system (ATPS) composed of polyethylene glycol (PEG) 6000 and phosphate was optimised by surface response methodology. A central composite design was used to evaluate the influence of phosphate, PEG and NaCl concentration and of the pH on the purity and extraction yield of IgG from a simulated serum medium. The conditions that maximise the partition of IgG into the upper phase were determined to be high concentrations of NaCl and PEG, low concentrations of phosphate and low pH values. An ATPS composed of 12% PEG, 10% phosphate, 15% NaCl at pH 6 was further used to purify human monoclonal antibodies from a Chinese Hamster Ovary (CHO) concentrated cell culture supernatant with a recovery yield of 88% in the upper PEG-rich phase and a purification factor of 4.3. This ATPS was also successfully used to purify antibodies from a hybridoma cell culture supernatant with a recovery yield of 90% and a purification factor of 4.1.     

Purification of a lectin from Canavalia ensiformis using PEG-citrate aqueous two-phase system

A PEG/citrate aqueous two-phase system was tested in the partition of commercial Concanavalin A (Con A) and subsequently applied to the extraction and purification of Con A from the crude extract of Canavalia ensiformis seeds. Con A was successfully extracted to the bottom phase of a system composed of 22% (w/w) PEG8000 and 12% (w/w) citrate at pH 6.0. The obtained purification factor was 11.5 without any loss in the hemagglutinating activity. The purity of extracted lectin was confirmed by SDS-PAGE analysis.     

白地霉Cryytococcus neoformans脂肪酶的双水相萃取

本文研究了不同无机盐的双水相体系对白地霉脂肪酶的萃取分离效果,对PEG/（NH4）2SO4成相系统进行了系统的研究,通过考察体系PEG分子量、不同的无机盐、PEG浓度、（NH4）2SO4浓度、离子强度、pH值及（NH4）2SO4浓度对反萃取的影响,并通过正交实验进一步优化了实验条件,初步确定在PEG浓度15%,（NH4）2SO4浓度22.5%,pH8.0,不加NaCl的条件下进行双水相萃取,脂肪酶分离系数和纯化倍数分别为6.8和7.5,比活力达到40.3 U/mg蛋白。     

Relative hydrophobicity of organic compounds measured by partitioning in aqueous two-phase systems

Partitioning of a variety of organic compounds, the majority of which represent therapeutic drugs, was examined in an aqueous dextran–polyethylene glycol (Dex–PEG) two-phase system containing 0.15 M NaCl in 0.01 M sodium phosphate buffer at pH 7.3 and in an octanol–buffer (0.15 M NaCl in 0.01 M sodium phosphate buffer, pH 7.3) system. The possibility of introducing compounds to be partitioned in an aqueous two-phase system with dimethyl sulfoxide, and the effect of this solvent on the solute partitioning was explored. Relative hydrophobicity of the compounds was estimated and expressed in equivalent numbers of methylene units. Comparison of the results obtained for several subsets of compounds in the octanol–buffer and in aqueous Dex–PEG two-phase systems clearly demonstrates the advantage of aqueous two-phase partitioning for the hydrophobicity measurements over partitioning in octanol–buffer system.     

Extractive fermentation for enhanced gellan-hydrolysing enzyme production by Bacillus thuringiensis H14

A new extractive fermentation process using PEG and potassium phosphate aqueous two-phase system (ATPS) was developed for enhanced production of gellan-hydrolysing enzyme by Bacillus thuringiensis H14. Five different Bacillus sp. were tested for their ability to synthesize gellan-hydrolysing enzyme. Bacillus thuringiensis H14 was found to be the best organism for gellan-hydrolysing enzyme production. The enzyme showed maximum activity at pH 7.5 and 40 °C. The partition studies of gellan-hydrolysing enzyme in the system using PEG X (X = 9000, 6000, 4000) and potassium phosphate–water and PEG–sodium citrate–water system indicated at PEG (4000)– potassium phosphate–water is the best system for partitioning of gellan-hydrolysing enzyme into the PEG phase (K = 4.99). Gellan-hydrolysing enzyme production by Bacillus thuringiensis H14 was studied in ATPSs composed of PEG X (X = 9000, 6000, 4000) and potassium phosphate. The top phase is continuous and rich in PEG while the bottom phase is dispersed and is rich in phosphate, microbial cells being mainly retained in the bottom phase. The gellan-hydrolysing enzyme produced during fermentation partitioned into the upper PEG phase and total gellan-hydrolysing enzyme produced was 2.12, 2.29 and 2.40 times higher than that of homogeneous fermentation when the fermentations were carried out using PEG 9000–potassium phosphate–water, PEG 6000–potassium phosphate–water, PEG 4000–potassium phosphate–water systems respectively.     

Liquid-liquid extraction of a Schistosoma mansoni recombinant protein from an Escherichia coli extract in aqueous two-phase system

This work describes the partition of a Schistosoma mansoni tegumental antigen produced by a recombinant Escherichia coli strain using an aqueous two-phase system composed of polyethylene glycol (PEG) and potassium phosphate. The effects of the polymer molecular weight, tie line length and pH on antigen partitioning were investigated. The detection of the antigen in both phases were determined by ELISA. The system composed of PEG 3550 (19.7% w/w) and potassium phosphate (17.7% w/w) led to a yield of 59% and an antigen purification factor of 3 in the PEG-rich phase. It was observed that the antigen partition in ATPS was strongly affected by the pH value and tie line length. In addition, it was possible in a single step, to remove the cell debris, that precipitated at the interface of the system.     

Isolation of alpha-1-antitrypsin from human plasma by partitioning in aqueous biphasic systems of polyethyleneglycol-phosphate

The partitioning of alpha-1-antitrypsin was assayed in biphasic aqueous systems containing potassium phosphate and two polyethyleneglycols of molecular mass 600 and 1000, respectively. In order to isolate the alpha-1-antitrypsin from serum plasma, the partitioning behaviour of human serum albumin, its principal contaminant, was also studied. Several aqueous two-phase systems with different partitioning properties were obtained by varying the PEG1000/PEG600 mass proportion. In systems with PEG1000/PEG600 mass ratio of 8, the optimal difference between the partition coefficients of both proteins was found. Under such conditions, a satisfactory purification was carried out by a three-step extraction procedure. By applying this method the alpha-1-antitrypsin specific activity increased severalfold (nearly 10 times) with a yield of 43%.