利用核糖体工程选育丙酮丁醇菌提高丁醇产量

利用核糖体工程技术对丙酮丁醇梭菌Clostridium acetobutylicum L7进行诱变筛选,以获得丁醇高产菌株。使用链霉素诱变C.acetobutylicum L7并结合设计的平板转接逐次提高链霉素浓度的筛选路线,获得丁醇产量较高的菌株S3。结果表明,S3丁醇产量为(12.48±0.03)g/L,乙醇产量为(1.70±0.07)g/L,相对于原始菌分别提高了11.2%及50%;丁醇/葡萄糖转化率由原始菌的0.19提高到0.22,丁醇生产率达到0.24 g/(L.h),相比提高30.5%;耐受丁醇浓度由原始菌的12 g/L提高到14 g/L;发酵液粘度下降到4 mPa/s,同比降低了60%,利于后续分离工作的进行,降低发酵成本。进一步研究工作表明,S3菌株遗传稳定性良好。因此,核糖体工程技术是一种选育丁醇高产菌株的有效方法。     

丙酮丁醇梭菌的基因编辑工具及代谢工程改造

丙酮丁醇梭菌作为极具潜力的新型生物燃料丁醇的生产菌,受到各国研究学者的广泛关注。通过丙酮丁醇梭菌(ABE)发酵生产丁醇,由于生产成本高,限制了其工业化应用。随着基因组学和分子生物学的快速发展,适用于丙酮丁醇的基因编辑工具不断发展并应用于提高菌株的发酵性能。本文对丙酮丁醇梭菌基因编辑工具和代谢工程改造取得的进展进行综述。     

高浓度丁醇浸泡及N＋束注入诱变双重作用筛选丁醇高产菌

通过高浓度丁醇浸泡处理丙酮丁醇梭菌（Clostridiumacetobutylicum）CL-2,筛选得到一株丁醇耐受能力提高并溶剂产量增加的菌株BR30—2,丁醇产量达11．77g/L,比CL-2提高了16．65％。以BR30—2作为出发菌株,进行N＋束注入诱变,筛选得到高产菌株BH．9,丁醇产量达14．5g/L,总溶剂为23．14g／L。在BH-9发酵过程中添加0．1％丁酸钠,丁醇产量达到16．59g/L,丁醇比例提高至67．38％。     

丙酮丁醇梭菌XY16丁醇发酵特性

以诱变选育的1株突变菌株丙酮丁醇梭菌XY16为对象,对影响该菌发酵特性的相关因素(N源、生长因子、热激)进行研究。结果显示:无机N源乙酸铵比其他N源更有利于丙酮丁醇的发酵,玉米浆或玉米蛋白可以直接替代生长因子进行丙酮丁醇发酵,热激可以提高总溶剂产量,最高可以达到21.28 g/L。该菌还可以同时利用葡萄糖和木糖,当葡萄糖利用完后,木糖才能被有效利用。     

丙酮丁醇梭菌的遗传操作系统

丙酮丁醇梭菌是极具潜力的替代燃料——生物丁醇的合成菌,受到各国研究者的普遍关注。丙酮丁醇梭菌菌株改造是生物丁醇产业化进程中的一项重要工作,其中遗传操作是核心内容之一。以下对丙酮丁醇梭菌的遗传操作系统的发展历史、种类和原理进行了综述,分析了目前几种遗传操作系统的局限性,并对其发展进行了展望。     

糖丁基梭菌产丁醇途径在大肠杆菌中的构建及发酵

摘要:【目的】通过克隆来源于糖丁基梭菌(Clostridium saccharobutylicum DSM13864)丁醇合成途径的关键酶基因(thlA,bcs-operon和adhE),构建产丁醇大肠杆菌。【方法】以Clostridium saccharobutylicum DSM13864的基因组为模板,分别扩增丁醇途径关键酶基因thlA,bcs-operon(crt-bcd1-etfB2-fixB2-hbd)和adhE,构建了两个重组质粒pETDuet-bcs和pRSFDuet-thlA-adhE,并成功转入E.coli JM109(DE3)实现异源表达,使大肠杆菌具备产丁醇能力。在半厌氧条件下进行重组菌的发酵,并研究不同培养基对产丁醇的影响。【结果】该重组菌在半厌氧条件下经摇瓶发酵丁醇产量达到25.4 mg/L,通过优化培养基后,在TB发酵培养基中丁醇产量可达到34.1 mg/L。【结论】通过构建重组共表达质粒,将糖丁基梭菌来源的丁醇途径关键酶基因在大肠杆菌中表达,成功构建产丁醇大肠杆菌。该研究提供了一株易于操作的丁醇发酵重组大肠杆菌,避免了传统梭菌发酵丁醇生产中苛刻的厌氧条件、易产孢子等限制问题。     

丙酮丁醇梭菌发酵菊芋汁生产丁醇

对丙酮丁醇梭菌Clostridium acetobutylicum L7发酵菊芋汁酸水解液生产丁醇进行了初步研究。实验结果表明,以该水解液为底物生产丁醇,不需要添加氮源和生长因子。当水解液初始糖浓度为48.36 g/L时,其发酵性能与以果糖为碳源的对照组基本相同,发酵终点丁醇浓度为8.67 g/L,丁醇、丙酮和乙醇的比例为0.58∶0.36∶0.06,但与以葡萄糖为碳源的对照组相比,发酵时间明显延长,表明该菌株葡萄糖转运能力强于果糖。当水解液初始糖浓度提高到62.87 g/L时,发酵终点残糖浓度从3.09 g/L增加到3.26 g/L,但丁醇浓度却提高到11.21 g/L,丁醇、丙酮和乙醇的比例相应为0.64∶0.29∶0.05,表明适量糖过剩有助于C.acetobutylicum L7胞内代谢从丙酮合成向丁醇合成途径调节;继续提高水解液初始糖浓度,发酵终点残糖浓度迅速升高,丁醇生产的技术经济指标受到明显影响。     

提高丙酮丁醇梭菌产溶剂稳定性及防止退化的研究

在丙酮丁醇梭菌连续传代过程中,添加乙酸钠可增强其稳定性,同时在未添加乙酸钠的发酵液中分离获得溶剂产量明显降低的退化菌株DNU83,其丁醇产量为2.33 g·L-1,仅为初始菌株的1/6.培养基中添加乙酸钠、丁酸钠或K2 HPO4等弱酸盐均可恢复退化菌株的产溶剂能力,如同时添加苄基紫精,可显著促进丁醇合成.7％玉米培养基中添加4 g·L -1 K2 HPO4和30 mg·L-1苄基紫精,丁醇产量可达18.01 g·L-1,总溶剂21.59 g·L-1,丁醇比为83.43％,丁醇产量较未退化菌株NU22提高24.09％.     

丙酮丁醇梭菌丁醇耐受性

丁醇在发酵培养基中的积累所产生的毒性问题是限制丁醇产量的重要因素,然而对于Clostridium acetobutylicum是如何适应丁醇胁迫,进而调节菌体生长和代谢的,目前尚缺乏系统研究,不能全面揭示C.acetobutylicum的丁醇耐受性机制.对丙酮丁醇梭菌丁醇耐受性有关的研究成果进行了综述,旨在深入理解菌株丁醇耐受性发生改变的相关分子基础.希望为进行微生物丁醇耐受性分子机制的改造、提高菌株的丁醇耐受性提供新的研究思路.     

限制葡萄糖、葡萄糖/乙酸双底物条件下自由控制丙丁梭菌ABE发酵丙酮浓度和丙酮/丁醇比

提出一种可以提高和自由控制丙丁梭菌ABE发酵丙酮浓度与丙酮/丁醇比的方法。（1）通过控制糖化酶用量、反应时间和温度调节玉米培养基初始葡萄糖浓度,使发酵进入到产溶剂期后,残留葡萄糖浓度降至接近于0 g/L的水平;（2）在葡萄糖受限的条件下,诱导丙丁梭菌合成分泌糖化酶,分解寡糖,将葡萄糖维持于低浓度,进而限制梭菌胞内糖酵解途径的碳代谢和NADH生成速度。与此同时,外添乙酸形成葡萄糖/乙酸双底物环境。在能量代谢基本不受破坏、丁醇未达到抑制浓度的条件下,适度抑制丁醇生产,有效地利用外添乙酸强化丙酮合成;（3）在外添乙酸的基础上,添加适量酿酒酵母,形成丙丁梭菌/酿酒酵母混合发酵体系,提高梭菌对高丁醇浓度的耐受能力。整个发酵体系可以将丙酮浓度和丙酮/丁醇比自由控制在5~12 g/L和0.5~1.0的水平,最大丙酮浓度和丙酮/丁醇比达到11.74 g/L和1.02,并可维持丁醇浓度于10~14 g/L的正常水平,充分满足工业ABE发酵对于丙酮和丁醇产品的不同需求。     

可发酵糖为底物不同菌种丁醇生产能力的研究

随着新一代生物质能源的研发,利用梭菌的发酵生产丁醇已成为热点。选用能生产丁醇的Clostridium acetobutylicum AS1.7,Clostridium acetobutylicum AS1.132,Clostridium acetobutylicumAS1.134和Clostridium beijerinckii NCMIB 8052,在多种糖源下进行发酵培养,通过比较其在不同糖源条件下的生长情况、糖利用率、丁醇及副产物产量、对丁醇、木糖耐受能力等,综合筛选出了最适用于发酵生产丁醇的备选菌种。NCMIB8052因具有最高产量、相对优良的耐受性及可利用多种糖源的特点,而被确定为发酵能力最强的菌种。     

利用甜菜糖蜜补料发酵生产丁醇

从土壤中分离出1株适合利用甜菜糖蜜发酵生产丁醇的丙酮丁醇梭菌(Clostridium acetobutylicum)2N,通过优化发酵条件,得到最适发酵温度为33℃,玉米浆最适添加量为15g/L,发现甜菜糖蜜中还原糖质量浓度高于50g/L时影响菌株的生长和溶剂生产。以补料分批发酵方式降低底物抑制,33℃发酵48h后,丁醇和总溶剂的质量浓度分别达到14.15g/L和19.65g/L,丁醇质量分数超过70%。     

Introducing a single secondary alcohol dehydrogenase into butanol-tolerant Clostridium acetobutylicum Rh8 switches ABE fermentation to high level IBE fermentation

ABSTRACT: BACKGROUND: Previously we have developed a butanol tolerant mutant of Clostridium acetobutylicum, Rh8, from the wild type strain DSM 1731. Strain Rh8 can tolerate up to 19 g/L butanol, with solvent titer improved accordingly, thus exhibiting industrial application potential. To test if strain Rh8 can be used for production of high level mixed alcohols, a single secondary alcohol dehydrogenase from Clostridium beijerinckii NRRL B593 was overexpressed in strain Rh8 under the control of constitutive thl promoter. RESULTS: The heterogenous gene sADH was functionally expressed in C. acetobutylicum Rh8. This simple, one-step engineering approach led to the complete conversion of acetone into isopropanol, achieving a total alcohol titer of 23.88 g/l (7.6 g/l isopropanol, 15 g/l butanol, and 1.28 g/l ethanol) with a yield to glucose of 31.42%. The acid (butyrate and acetate) assimilation rate in isopropanol producing strain Rh8(psADH) was increased. CONCLUSIONS: The improved butanol tolerance and the enhanced solvent biosynthesis machinery in strain Rh8 is beneficial for production of high concentration of mixed alcohols. Strain Rh8 thus can be considered as a good host for further engineering of solvent/alcohol production.     

Development and characterization of butanol — Resistant strain ofClostridium acetobutylicum in molasses medium

The production of acetone—butanol—ethanol solvents from cane molasses by locally isolated culture ofClostridium acetobutylicum was limited by butanol toxicity (1.6 mol/L). The butanol tolerance of the isolated culture was increased up to 4.8 mol/L by a serial enrichment method. The butanol-resistant strain had greater efficiency for the conversion of saccharides to mixed solvents and produced 52% more butanol at the expense of acetone and ethanol than the original strain. Moreover, the fermentation profile of parent and butanol-resistant strains in anerobic fermentation of cane molasses demonstrated the superiority of the latter in terms of growth rate, time of onset of butanol production, sugar utilization, final butanol concentration and other parameters.     

Use of immobilized microbial membrane fragments to remove oxygen and favor the acetone-butanol fermentation.

Oxygen-reducing membrane fragments obtained from Escherichia coli were used with Clostridium acetobutylicum (C. acetobutylicum) to provide an oxygen-free microenvironment for the conversion of glucose to acetone, butanol, and ethanol (ABE). The batch fermentation of suspended C. acetobutylicum NRRL-B-643 and its ability to produce solvents in the presence of membranes as the oxygen-elimination agent are described and compared with the conventional sparging technique used to maintain anaerobiosis. The use of membrane fragments to remove oxygen for fermentation by C. acetobutylicum was successful and gave slightly improved results over the use of sparing with regard to lag, biomass, and solvent production (e.g., final butanol concentration of 3.25 and 2.7 g/L, respectively). Solvent production is also reported for a continuous columnar reactor with coimmobilized cells and membranes in kappa-carrageenan gel beads and air-saturated liquid feed.     

Genomic analysis of carbon monoxide utilization and butanol production by Clostridium carboxidivorans strain P7

Increasing demand for the production of renewable fuels has recently generated a particular interest in microbial production of butanol. Anaerobic bacteria, such as Clostridium spp., can naturally convert carbohydrates into a variety of primary products, including alcohols like butanol. The genetics of microorganisms like Clostridium acetobutylicum have been well studied and their solvent-producing metabolic pathways characterized. In contrast, less is known about the genetics of Clostridium spp. capable of converting syngas or its individual components into solvents. In this study, the type of strain of a new solventogenic Clostridium species, C. carboxidivorans, was genetically characterized by genome sequencing. C. carboxidivorans strain P7(T) possessed a complete Wood-Ljungdahl pathway gene cluster, involving CO and CO(2) fixation and conversion to acetyl-CoA. Moreover, with the exception of an acetone production pathway, all the genetic determinants of canonical ABE metabolic pathways for acetate, butyrate, ethanol and butanol production were present in the P7(T) chromosome. The functionality of these pathways was also confirmed by growth of P7(T) on CO and production of CO(2) as well as volatile fatty acids (acetate and butyrate) and solvents (ethanol and butanol). P7(T) was also found to harbour a 19 Kbp plasmid, which did not include essential or butanol production related genes. This study has generated in depth knowledge of the P7(T) genome, which will be helpful in developing metabolic engineering strategies to improve C. carboxidivorans's natural capacity to produce potential biofuels from syngas.     

The acetone butanol fermentation on glucose and xylose. II. Regulation and kinetics in fed-batch cultures

The kinetics in fed-batch cultures of acetone butanol fermentation by Clostridium acetobutylicum is compared on glucose, xylose, and mixtures of both sugars. The final conversion yield of sugars into solvents always increases with the sugar feeding rate. At low feeding rates, the sugar concentration in the medium becomes limiting, which results in a slower cellular growth, a slower metabolic transition from an acid to a solvent fermentation and, thus, a higher accumulation of acids. It is only at sufficiently high feeding rates that fed-batch fermentations yield kinetic results comparable to those of batch fermentations. With mixtures of glucose and xylose, because of a maintained low glucose level, both sugars are taken up at the same rate during a first fermentation period. An earlier accumulation of xylose when the fermentation becomes inhibited suggest that xylose utilization is inhibited when the catabolic flux of glucose alone can satisfy the metabolic activity of the cell. Kinetic results with batch and fed-batch fermentations indicate several important features of the regulation of C. acetobutylicum metabolism: an early inhibition by the produced acids; an initiation of solvent formation between 4 and 6 g/L acetic and butyric acid depending on the metabolic activity of the cell; a metabolic transition from acids to solvents production at a rate closely related to the rate of sugar uptake; during solvent production, a reassimilation of acids above a minimal rate of sugar consumption of 0.2 h(-1); a final inhibition of the fermentation at a total butanol and acids concentration of ca. 20 g/L.