Application of polyethylene glycol immobilized Clostridium sp. LS2 for continuous hydrogen production from palm oil mill effluent in upflow anaerobic sludge blanket reactor

A novel polyethylene glycol (PEG) gel was fabricated and used as a carrier to immobilize Clostridium sp. LS2 for continuous hydrogen production in an upflow anaerobic sludge blanket (UASB) reactor. Palm oil mill effluent (POME) was used as the substrate carbon source. The optimal amount of PEG-immobilized cells for anaerobic hydrogen production was 12% (w/v) in the UASB reactor. The UASB reactor containing immobilized cells was operated at varying hydraulic retention times (HRT) that ranged from 24 to 6 h at 3.3 g chemical oxygen demand (COD)/L/h organic loading rate (OLR), or at OLRs that ranged from 1.6 to 6.6 at 12 h HRT. The best volumetric hydrogen production rate of 336 mL H₂/L/h (or 15.0 mmol/L/h) with a hydrogen yield of 0.35 L H₂/g COD_removed was obtained at a HRT of 12 h and an OLR of 5.0 g COD/L/h. The average hydrogen content of biogas and COD reduction were 52% and 62%, respectively. The major soluble metabolites during hydrogen fermentation were butyric acid followed by acetic acid. It is concluded that the PEG-immobilized cell system developed in this work has great potential for continuous hydrogen production from real wastewater (POME) using the UASB reactor.     

Sewage treatment in a combined up-flow anaerobic sludge blanket (UASB)–down-flow hanging sponge (DHS) system

The performance of up-flow anaerobic sludge blanket (UASB) in combination with down-flow hanging sponge (DHS) system for sewage treatment at an average wastewater temperature of 15 °C has been investigated for 6 months. The results showed that a combined system operated at a total HRT of 10.7 h and total SRT of 88 days represents a cost effective sewage treatment process. The average COD_total and BOD_5 total concentrations measured in the final effluent of the total system (UASB + DHS) amounted to 43 and 3.0 mg/l, respectively, corresponding to the overall removal efficiency of 90% for COD_total and 98% for BOD_5 total. The total process provided a final effluent containing a low concentration of 12 mg/l for TSS.Eighty-six percent of ammonia was eliminated at space loading rate of 1.6 kg COD/m³ d and HRT of 2.7 h. The calculated nitrification rate of the DHS system according to the nitrate and nitrite production amounted to 0.18 kg/m³ d. The removal of F. coliform in the UASB reactor only amounted to 0.86 log₁₀. On the other hand, the F. coliform concentration dropped substantially, i.e. by 2.6 log₁₀ in the DHS system resulting only 2.7 × 10³/100 ml in the final effluent.The calculated average sludge production for UASB operated at an HRT of 8.0 h amounted to 30 g TSS/d, corresponding to sludge yield coefficient of 0.2 g TSS/g total COD removed, while it was indeed very low only 6.0 g TSS/d corresponding to sludge yield coefficient of 0.09 g TSS/g total COD removed, for DHS system.The DHS profile results revealed that in the first and second segment of DHS system, the COD_total, BOD_5 total and TSS was eliminated, followed by the oxidation of ammonia in the next segments.     

Anaerobic treatment of low-strength wastewater with a high fraction of particulate matter in an unconventional two-phase ASBRs system

The results of a two-phase anaerobic system using anaerobic sequencing batch reactors (ASBRs), treating low-strength wastewater (COD ∼ 500 mg/L) with a high fraction of particulate organic matter (70%, COD basis), are presented. Two reactors in series were used; the first one was hydrolytic–acidogenic, while the second one was methanogenic. This configuration was proposed to promote high efficiency solids removal. During the experiment, 69% and 50% efficiencies of total COD removal were obtained for OLRs of 0.63 and 1.22 kgCOD/(m³ d), respectively. Values of the solubilized organic fraction (SOF) achieved in the hydrolytic–acidogenic reactor were within the range of 0.3–0.6 gCOD_solubilized/gpCOD_removed, and the average acidified organic fraction (AOF) was 0.6 gCOD_VFA-produced/gsCOD_fed. The methanogenic reactor had a VFA removal fraction (VFARF) between 0.4 and 0.6 gCOD_VFA-removed/gCOD_VFA-fed for the OLR of 0.63 and 1.22. The two-phase ASBR system is suitable, and can be implemented, for the anaerobic treatment of this kind of wastewater.     

Solids hydrolysis and accumulation in a hybrid anaerobic digester-constructed wetlands system

The properties and behaviour of solids retained in a pilot plant constituted of an up-flow anaerobic sludge blanket (UASB) reactor and two constructed wetlands (CWs) were monitored over a 3-year period. The UASB (25.5 m³) was fed with raw municipal wastewater at a flow rate of 61–112 m³ d^?1 and a volumetric loading rate (VLR) of 0.75–1.70 kg TCOD m^?3 d^?1. The CWs (75 m² each) were operated in series and received a fraction (17–20 m³ d^?1) of the UASB effluent. The applied surface loading rates (SLR) were in the range of 3800–8700 g TCOD m^?2 d^?1 (UASB) and 11–15 g BOD₅ m^?2 d^?1 (CWs). The overall system removed 95% TSS, 85% TCOD and 87% BOD₅ on average. For influent VSS, the UASB removed 72.1% and gave a hydrolysis of 63.5%, while the average surplus sludge generation was 8.7%. Over the 3-year period, TSS and VSS accumulated in the CWs at rates of 1.07 and 0.56 kg m^?2 year^?1, respectively. The aerobic biodegradability of the accumulated solids ranged from 23 to 92 mg O₂ g VSS^?1 d^?1 and increased downstream in the CWs. About 59% of the VSS that entered the CWs was removed by hydrolysis, while 24% accumulated on granular media. These low solids accumulation rates were especially remarkable considering the high COD and BOD₅ loading rates applied. The system lay-out appear to be promising in terms of preventing clogging.     

An integrated anaerobic–aerobic bioreactor (IAAB) for the treatment of palm oil mill effluent (POME): Start-up and steady state performance

Palm oil mill effluent (POME) with average chemical oxygen demand (COD) and biochemical oxygen demand (BOD) of 70,000 and 30,000 mg/L, respectively, can cause serious environmental hazards if discharged untreated. There are conventional palm oil mill effluent (POME) treatment systems that require large footprint, long HRT and fail to meet the Malaysian Department of Environment (DOE) discharge limit. Hence, the current research is aimed to design a novel integrated anaerobic–aerobic bioreactor (IAAB) for POME treatment in order to overcome these shortcomings of the conventional system. IAAB is a new bioreactor configuration which integrates anaerobic and aerobic digestion in one reactor. The overall removal efficiencies in steady state condition in terms of chemical oxygen demand (COD), biochemical oxygen demand (BOD) and total suspended solids (TSS) were more than 99% at the organic loading rate (OLR) of 10.5 g COD/L day with methane yield of 0.24 L CH₄/g COD removed. The effluent quality remained stable (BOD < 70 mg/L) and complied with the discharge limit (BOD < 100 mg/L). Overall, the IAAB system exhibited good stability and pH adjustment was unnecessary. The results show that the IAAB achieves higher performance in terms of organic removal efficiency and methane yield at higher OLR and shorter HRT as compared to the conventional system. Further evaluations of its long-term performance are proposed for the subsequent study.     

Thermophilic treatment of bulk drug pharmaceutical industrial wastewaters by using hybrid up flow anaerobic sludge blanket reactor

The hybrid up flow anaerobic sludge blanket reactor was evaluated for efficacy in reduction of chemical oxygen demand (COD) and biochemical oxygen demand (BOD) of bulk drug pharmaceutical wastewater under different operational conditions. The start-up of the reactor feed came entirely with glucose, applied at an organic loading rate (OLR) 1 kg COD/m³ d. Then the reactor was studied at different OLRs ranging from 2 to 11 kg COD/m³ d with pharmaceutical wastewater. The optimum OLR was found to be 9 kg COD/m³ d, where we found 65–75% COD and 80–94% of BOD reduction with biogas production containing 60–70% of methane and specific methanogenic activity was 320 ml CH₄/g-VSS d. By the characterization studies of effluent using GC–MS, the hazardous compounds like phenol, l,2-methoxy phenol, 2,4,6-trichloro phenol, dibutyl phthalate, 1-bromo naphthalene, carbamazepine and antipyrine were present. After the treatment, these compounds degraded almost completely except carbamazepine. Thermophilic methanothrix and methanosaetae like bacteria are present in the granular sludge.     

Comparison of CSTR and UASB reactor configuration for the treatment of sulfate rich wastewaters under acidifying conditions

The effects of lowering the operational pH from 6 to 5 on mesophilic (30 °C) sulfate reduction during the acidification of sucrose at an organic loading rate of 5 gCOD (l_reactor d)⁻¹ and at a COD/SO₄²⁻ ratio of 4 were evaluated in a CSTR and in a UASB reactor. The HRT was 24 h and 10 h, respectively. Acidification was complete in both reactors at pH 6 and the lowering of the operational pH to 5 did not affect the acidification efficiency in the CSTR but decreased the acidification efficiency of the UASB to 72%. The decrease to pH 5 caused an increase in the effluent butyrate and ethanol concentrations in both reactors. Lowering the pH from 6 to 5 caused a decrease in sulfate reduction efficiencies in both reactors, from 43% to 25% in the CSTR and from 95% to 34% in the UASB reactor. The acidification and sulfate reduction efficiencies at pH 5 could be increased to 94% and 67%, respectively, by increasing the HRT of the UASB reactor to 24 h.     

Alkalinity ratios to identify process imbalances in anaerobic digesters treating source-sorted organic fraction of municipal wastes

Two 5 L anaerobic reactors were used to monitor the mesophilic anaerobic digestion of source sorted organic fraction of municipal solid wastes (SS-OFMSW) focusing the attention on the response of alkalinity ratios. Intermediate/partial alkalinity (IA/PA) ratio can be used as a simple and cheaper alternative to VFAs analysis when digester's stability needs to be assessed in full-scale plants treating these organic wastes. However, lab-scale studies in order to establish a specific limit value of IA/PA referred to SS-OFMSW had not been conducted. In this study, a reference reactor (R1) was operated at low organic loading rates (OLR) and high hydraulic retention times (HRT) during 165 days. Besides, severe disturbances were applied to a second reactor (R2) during 281 days by means of increasing both HRT and OLR in order to assess the digester response under continuous overload conditions. The obtained results show that an IA/PA ratio of below 0.3 is recommended to maintain total VFAs between 2.5 and 3.5 kg m⁻³ and achieve a stable reactor performance treating SS-OFMSW in a range of total alkalinity (TA) between 13 and 15 kg CaCO₃ m⁻³. These results provide a starting point to develop further works in full-scale digesters, in order to improve the monitoring and process control of full-scale anaerobic reactors treating SS-OFMSW.     

Dephenolisation of olive mill wastewater using adapted Trametes versicolor

Olive mill wastewater (OMW) is an effluent of the olive oil extraction process. The large volumes involved, along with the high phenolic content and chemical oxygen demand, cause major environmental problems. The presence of phenolics limits the effectiveness of aerobic or anaerobic treatment of this wastewater. In most of the studies performed on OMW, the concentration of phenolics is reduced by diluting the OMW prior to biological treatment, which leads to an increase in waste volume. Therefore, the aim of this work was to investigate the possibility of reducing the phenolic content without dilution and without any addition of nutrients or pretreatment by using the white-rot fungi Trametes versicolor FPRL 28A INI. Through an adaptation process, the fungus was able to remove 78% of total phenolics in shake flask experiments and 39% in static culture using undiluted OMW medium. In continuously stirred tank reactor (CSTR) conditions, 70% of total phenolics removal was achieved. Analysis with GC–MS showed that all simple phenolics disappeared from the medium after the 8th day of cultivation at an 0.25 vvm aeration rate. The maximum activities of phenol degrading enzymes laccase and manganese peroxidase (MnP) obtained under these conditions were 762.14 ± 42.11 and 97.80 ± 8.11 U l^?1 respectively.     

Bioelectricity generation using two chamber microbial fuel cell treating wastewater from food processing

Electricity generation from microbial fuel cells which treat food processing wastewater was investigated in this study. Anaerobic anode and aerobic cathode chambers were separated by a proton exchange membrane in a two-compartment MFC reactor. Buffer solutions and food industry wastewater were used as electrolytes in the anode and cathode chambers, respectively. The produced voltage and current intensity were measured using a digital multimeter. Effluents from the anode compartment were tested for COD, BOD₅, NH₃, P, TSS, VSS, SO₄ and alkalinity. The maximum current density and power production were measured 527 mA/m² and 230 mW/m² in the anode area, respectively, at operation organic loading (OLR) of 0.364 g COD/l.d. At OLR of 0.182 g COD/l.d, maximum voltage and columbic efficiency production were recorded 0.475 V and 21%, respectively. Maximum removal efficiency of COD, BOD₅, NH₃, P, TSS, VSS, SO₄ and alkalinity were 86, 79, 73, 18, 68, 62, 30 and 58%, respectively. The results indicated that catalysts and mediator-less microbial fuel cells (CAML-MFC) can be considered as a better choice for simple and complete energy conversion from the wastewater of such industries and also this could be considered as a new method to offset wastewater treatment plant operating costs.     

Anaerobic thermophilic digestion of cutting oil wastewater: Effect of co-substrate

This paper describes the thermophilic (55 °C) anaerobic biodegradation of a mixed feed composed of vinasses and cutting oil wastewater (COW) in a laboratory upflow anaerobic fixed-film reactor (UAFF) with a porous support medium. The experimental protocol was defined to examine the effect of increasing the percentage of cutting oil wastewater in the feed.The UAFF reactor was initially started-up with vinasses as the only carbon source at an organic loading rate of 22.3 kg COD/m³ day and HRT of 0.8 days using porous particles as the support (SIRAN). The percentage of organic matter composed of vinasses was subsequently reduced while increasing the amount of cutting oil until 100% of cutting oil wastewater was added in the feed. Four stages were considered in the study (0, 42.4, 66.6 and 100% COW). HRT was adjusted in order to maintain an approximately constant organic loading rate applied to the system. Under theses conditions, the UAFF reactor was subjected to a programme of steady-state operation with hydraulic retention times (HRT) in the range 0.8–0.15 days and organic loading rates (OLR) between 22.3 and 14.9 kg COD/m³ day in order to evaluate the treatment capacity of the system.The COD removal efficiency was found to be 87% COD and 94.6% TOC in the reactor when treating vinasses at 22.3 kg COD/m³ day. The volumetric methane level produced in the digester reached 0.45 m³/m³ day. After an operating period of 120 days, the reactor was fed with cutting oil wastewater (COW) as the only source of carbon. An OLR of 16.7 kg COD/m³ day was achieved with 85.8% COD removal efficiency (58.1%TOC) in the experimental UAFF reactor. Under these conditions the volumetric methane produced in the digester was negligible.Hence, COW can be removed, if not degraded, by anaerobic treatment in the presence of a biodegradable co-substrate. Wine vinasses degradation creates conditions for non-biological removal of COW constituents. More studies are necessary in order to test the mechanisms of organic removal when biodegradation apparently had ceased. Also, toxicity assays of COW are necessary to evaluate the toxicity to the methanogenic community.     

Assessment of a UASB reactor with high ammonia concentrations: Effect of zeolite addition on process performance

The UASB process for wastewater treatment has been extensively studied, but the use of zeolite to improve UASB reactor performance has rarely been explored. In this study, a UASB reactor modified with natural zeolite operating at high nitrogen concentrations (0.5, 0.7 and 1 g/L) was evaluated. Two laboratory bioreactors, one with zeolite and one without, were operated at ambient temperatures ranging between 18 °C and 21 °C. The experimental phase had a start-up period of 21 days. In the reactor with zeolite, the pH was found to be between 7.9 and 9.1, with a COD removal efficiency of about 60% after 80 days of operation at ammonia concentrations of between 0.229 and 0.429 g/L in the effluent. In the reactor without zeolite, the pH was between 8.3 and 9.3, and the COD removal efficiency was about 40% at ammonia concentrations between 0.244 and 0.535 g/L in the effluent. The addition of zeolite also decreased the volatile suspended solids (VSS) concentration in the effluent, generating a biomass with larger granules and higher settling rates as compared to a UASB reactor without zeolite. Taking the lower ammonia concentration, the higher COD removal and the improved granulation into account, it can be concluded that natural zeolite positively influenced the behavior and performance of the UASB reactor operating with high nitrogen concentrations.     

Improving biogas production from protein-rich distillery wastewater by decreasing ammonia inhibition

A large quantity of protein-rich distillery wastewater is produced during the process of bio-ethanol production from kitchen waste. It is difficult, however, to treat protein-rich distillery wastewater by anaerobic digestion due to ammonia inhibition. In this study, a novel method was investigated to reduce ammonia inhibition during thermophilic anaerobic digestion through the recirculation of water-washed biogas into the headspace (R1 system) or liquid phase (R2 system) of the reactors. The results show that the method greatly improved biogas production from distillery wastewater. R2 system achieved stable biogas production at a higher organic loading rate (OLR) of 4.0 g VTS/L/d than R1 system at 3.0 g VTS/L/d. At the same OLR, we observed a higher biogas production rate but lower accumulation of NH₄⁺ and volatile fatty acids in the reactor, and higher ammonia absorption rate in the water tank of R2 system than R1 system. The better performance of R2 system could be attributed to the more efficient removal of ammonia from liquid phase. In addition, adjusting the C/N ratio of distillery wastewater from 9.0 to 11.4 significantly enhanced the maximum OLR from 3.0 to 7.0 g VTS/L/d in R1 system.     

Anaerobic granule development for removal of pentachlorophenol in an upflow anaerobic sludge blanket (UASB) reactor

The granulation process using synthetic wastewater containing pentachlorophenol (PCP) in four 1.1 l laboratory scale upflow anaerobic sludge blanket (UASB) reactors was studied, and the anaerobic biotransformation of PCP during the granulation process investigated. After 110 days granular sludge was developed and up to 160 and 180 mg/l of PCP was added into the reactors R1 and R2, respectively, when they were inoculated with acclimated anaerobic sludge from an anaerobic digester of a citric acid plant. The inoculum was predominately composed of bacilli and filamentous bacteria. Granulation did not occur in reactors R3 and R4 which were inoculated with acclimated anaerobic sludge from aerobic sludge of the municipal sewage treatment plant which consisted mainly of cocci. Despite similar bacilli in the granule, the filamentous bacteria from reactor R1 were thicker than those of reactor R2. The granular sludge had a maximum diameter of 2.5 and 2.2 mm, and SMA of 1.44 and 1.32 gCOD/gTVS per day for reactors R1 and R2, respectively. Over 98% chemical oxygen demand (COD) removal rate and 99% of PCP removal rate were achieved when reactors R1 and R2 were operated at PCP and COD loading rates of 150 and 7.5 g/l per day, respectively. H₂-producing acetogens were the dominant anaerobes in the granular sludge.     

Combined industrial and domestic wastewater treatment by periodic allocating water hybrid hydrolysis acidification reactor followed by SBR

A pilot-scale hybrid hydrolysis acidification reactor (HHAR) with periodic water allocation mode operation followed by sequencing batch reactor (SBR) in anoxic and aerobic metabolic function was evaluated for the treatment of low-biodegradable combined industrial and domestic wastewater. The HHAR combines the advantages of both the UASB reactor and AF, omitting the three-phase separator. Furthermore, it has lower average up-flow velocity (0.38–0.92 m/h) and higher periodic up-flow velocity (6 m/h), which made the reactor keep higher MLSS concentration (more than 10,000 mg/L) and sludge-bed is in periodic “expansion-sedimentation-expansion” state. When HRT less than 10 h, the B/C variation was positive and reached the maximum value of 0.07 at 8 h. SBR with a total cycle period of 4.5 h was applied as the post-treatment process to remove residual COD, NH₃-N and TN. At steady stage, the pilot-scale SBR effluent COD, NH₃-N and TN concentration was 65, 0.75 and 17.71 mg/L, corresponding in this case to full-scale SBR plant effluent was 93, 16.4 and 34 mg/L. Comparison results indicated that the application of HHAR–SBR system to treat combined industrial and domestic wastewater can improve effluent quality significantly.     

Effects of nitrobenzene concentration and hydraulic retention time on the treatment of nitrobenzene in sequential anaerobic baffled reactor (ABR)/continuously stirred tank reactor (CSTR) system

The effects of increasing nitrobenzene (NB) concentrations and hydraulic retention times (HRT) on the treatment of NB were investigated in a sequential anaerobic baffled reactor (ABR)/aerobic completely stirred tank reactor (CSTR) system. In the first step of the study, the maximum COD removal efficiencies were found as 88% and 92% at NB concentrations varying between 30 mg L^?1 and 210 mg L^?1 in ABR. The minimum COD removal efficiency was 79% at a NB concentration of 700 mg L^?1. The removal efficiency of NB was nearly 100% for all NB concentrations in the ABR reactor. The methane gas production and the methane gas percentage remained stable (1500 mL day^?1 and 48–50%, respectively) as the NB concentration was increased from 30 to 210 mg L^?1. In the second step of the study it was found that as the HRT decreased from 10.38 days to 2.5 days the COD removal efficiencies decreased slightly from 94% to 92% in the ABR. For maximum COD and NB removal efficiencies the optimum HRT was found as 2.5 days in the ABR. The total COD removal efficiency was 95% in sequential anaerobic (ABR)/aerobic (CSTR) reactor system at a minimum HRT of 1 day. When the HRT was decreased from 10.38 days to 1 day, the methane percentage decreased from 42% to 29% in an ABR reactor treating 100 mg L^?1 NB. Nitrobenzene was reduced to aniline under anaerobic conditions while aniline was mineralized to catechol with meta cleavage under aerobic conditions.     

Seasonal and annual performance of a full-scale constructed wetland system for sewage treatment in China

A full-scale constructed wetlands system with a total area of 80 ha and treatment capability of 2.0 × 10⁴ m³ d⁻¹ was completed in October 1998 in Rongcheng, Shandong Province, China. To evaluate wastewater treatment effectiveness and seasonal performance of the system, water samples were collected and analyzed from January 1999 to December 2004. Comparison of mean inlet and outlet concentrations showed that the constructed wetland system could effectively reduce the output of SS (71.8 ± 8.4%), BOD₅ (70.4 ± 9.6%), COD (62.2 ± 10.1%), total coliform (99.7%) and fecal coliform (99.6%). However, the percent reduction of ammonia nitrogen was relatively low (40.6 ± 15.3%), and total phosphorus showed the least efficient reduction (29.6 ± 12.8%). BOD₅, COD, ammonia nitrogen, and total phosphorus removal efficiencies displayed seasonal variations. BOD₅ and COD removal was more efficient in spring and summer than in autumn and winter whereas ammonia nitrogen and total phosphorus removal was more efficient in summer and autumn than in spring and winter. Annual variation analysis shows that COD, BOD₅, and ammonia nitrogen reduction efficiencies increased from 1999 to 2004. In contrast, mean total phosphorus reduction efficiency did not change from 2001 to 2002 and began to decrease from 2003 onwards.     

Application of anaerobic–aerobic sequential treatment system to real textile wastewater for color and COD removal

A sequential anaerobic packed column reactor and an activated sludge unit was operated continuously for treatment of a textile industry wastewater, in Izmir, Turkey. Metal sponges were used as support material in anaerobic unit and pre-activated textile dyestuff biodegrading PDW facultative anaerobic bacterial culture was immobilized on the support particles. Effects of hydraulic retention times in anaerobic unit (θ_H anaerobic = 12–72 h) and initial COD concentration (COD₀ = 3000 ± 200 mg/L and 800 ± 100 mg/L) at θ_H anaerobic = 24 h on color and COD removal performance of the system were investigated. The results indicated that over 85% decolorization and about 90% COD removal efficiency can be obtained up to θ_H anaerobic = 48 h but higher retention times causes decreasing in decolorization efficiency. Operating the system with real wastewater without adding any nutrients at θ_H anaerobic = 24 h resulted in over 60% improvement in color removal in studied wastewater compared to existing treatment plant.     

Effect of influent pH and alkalinity on the removal of chlorophenols in sequential anaerobic–aerobic reactors

This study was carried out to determine the effect of influent pH and alkalinity on the performance of sequential UASB and RBC reactors for the removal of 2-CP and 2,4-DCP from two different simulated wastewaters. The performance of methanogens at low (<6.0) to high (>8.0) pH values and at sufficiently high alkalinity (1500–3500 mg/l as CaCO₃) is described in this paper. Sequential reactors were capable of handling wastewaters with influent pH, 5.5–8.5. However, with influent pH 7.0 ± 0.1 UASB reactor showed best performance for 2-CP (99%) and 2,4-DCP (88%) removals. Increase in alkalinity/COD ratio in the influent (>1.1) caused gradual decrease in the chlorophenol removal in UASB reactors. The UASB reactors could not tolerate wastewater with higher alkalinity/COD ratio (2.6) and showed significant deterioration of its performance in terms of chlorophenols removal achieving only 74.7% 2-CP and 60% 2,4-DCP removals, respectively.     

Minimizing land requirement and evaporation in small wastewater treatment systems

Water supplies in the Middle East arid climate are a scarce commodity making treated wastewater an economically attractive source for increasing the limited existing water resources for agricultural purposes. In order to minimize water losses with the corresponding increased salinity and to reduce land demand, an integrated system based mainly on high-rate semi-intensive treatment units is being tested and demonstrated. The units include an upflow anaerobic sludge blanket (UASB) reactor and vertical and horizontal flow wetlands. The units are characterized by simple and low-cost maintenance with minimal energy input. Three years of pilot plant results from the combined system are presented in this paper. The results show a high organic removal rate for the combined system: 140 g COD/m²/day for the scheme, which included a UASB reactor followed by two PAVB units and subsurface horizontal flow CW. Even higher rates of 900 g COD/m²/day were achieved for the same scheme by replacing the final CWL with another PAVB unit. These high rates allow for a small treatment plant footprint equivalent to 0.13–0.9 m² per person, assuming 125 g COD per person per day.