Recovery of penicillin by reactive extraction in centrifugal extractors

Penicillin V and/or G were extracted from fermentation broth by Amberlite LA-2 in n-butylacetate at pH 5 in a laboratory centrifugal extractor, Type SA 01 of Westfalia, up to an overall phase throughput rate of 30 L/h, in a bench-scale four-stage extraction system, consisting of Type TA 1 of Westfalia, up to an overall phase throughput rate of 110 L/h, and in a pilot-plant three-stage extraction unit, consisting of Type TA 7 extractors of Westfalia, up to a phase throughput rate of 990 L/h with very high degrees of extraction (up to 99%). The reextraction from the ion-pair complex, which contained organic solvent, was performed by phosphate, borate, or carbonate buffer at pH 7.5-8.5 in all three extractor systems with degrees of extraction up to 98%, but at considerably lower overall phase throughput rates than those of the extraction, since no satisfactory phase separation is possible at higher throughput rates.     

Enhanced production of surfactin from Bacillus subtilis by addition of solid carriers

Addition of a small quantity of solid porous carriers (e.g., activated carbon or expanded clay) into fermentation broth significantly increased surfactin production with Bacillus subtilis ATCC 21332. Culture medium containing 25 g L(-1) of activated carbon gave an optimal surfactin yield of 3600 mg L(-1), which was approximately 36-fold higher than that obtained from carrier-free liquid culture. The marked increase in surfactin production was primarily attributed to stimulation of cell growth due to the presence of activated carbon carriers. Concentration of limiting carbon substrate (glucose) is also an important factor affecting the production of surfactin, as an initial glucose concentration of 40 g L(-1) resulted in optimal surfactin production. An appropriate agitation rate also benefited surfactin production, as the best yield appeared at an agitation rate of 200 rpm. Surfactin was purified from fermentation broth via a series of acidic precipitation and solvent extraction. The resulting product was nearly 90% pure with a recovery efficiency of ca. 72%. The purified surfactin reduced the surface tension of water from 72 to 27 mN m(-1) with a critical micelle concentration of ca. 10 mg L(-1). The surfactin product also attained an emulsion index of 70% for kerosene and diesel at a low concentration of 100 and 600 mg L(-1), respectively.     

Recovery of penicillin G from fermentation broth with reactive extraction in a mixer-settler

Summary In a laboratory countercurrent mixer-settler, penicillin was recovered from its fermentation broth by extraction with Amberlite LA-2 in n-butylacetate at pH 5.0 and reextracted from the ion-pair complex containing a solvent phase with a buffer at 7.2–7.5 with an overall degree of extraction above 90 %.Symbols A amine - AHP complex - c concentration - C partition coefficent - E degree of extraction - HP penicillin acid - K_G equilibrium constant - P, P^– penicillin acid anion Indices aq aqueous phase - org organic phase - A amine - AHP complex - G overall - HP free acid - P penicillin     

萃取耦合技术对玉米秸秆水解液发酵产丁醇的影响

本研究以玉米秸秆水解液为原料,通过萃取发酵技术生产燃料丁醇,以提高丁醇产量,降低生产成本。通过对萃取剂的筛选与条件优化,确定纤维丁醇发酵的萃取剂为油醇,添加时间为发酵0 h,添加比例为1:1 (V/V)。该条件下发酵32 g/L糖浓度的玉米秸秆水解液,丁醇和总溶剂产量分别为3.28 g/L和4.72 g/L,比对照分别提高958.1%和742.9%。以D301树脂脱毒后5%总糖浓度的玉米秸秆水解液进行丁醇萃取发酵,丁醇和总溶剂产量分别达到10.34 g/L和14.72 g/L,发酵得率为0.31 g/g,与混合糖发酵结果相当。研究结果表明萃取发酵技术能够显著提高原料的利用率和丁醇产量,为纤维丁醇工业化生产提供了技术支撑。     

Production of acetone butanol ethanol (ABE) by a hyper-producing mutant strain of Clostridium beijerinckii BA101 and recovery by pervaporation.

A silicone membrane was used to study butanol separation from model butanol solutions and fermentation broth. Depending upon the butanol feed concentration in the model solution and pervaporation conditions, butanol selectivities of 20.88-68.32 and flux values of 158.7-215.4 g m(-)(2) h(-)(1) were achieved. Higher flux values (400 g m(-)(2) h(-)(1)) were obtained at higher butanol concentrations using air as sweep gas. In an integrated process of butanol fermentation-recovery, solvent productivities were improved to 200% of the control batch fermentation productivities. In a batch reactor the hyper-butanol-producing mutant strain C. beijerinckii BA101 utilized 57.3 g/L glucose and produced 24.2 g/L total solvents, while in the integrated process it produced 51.5 g/L (culture volume) total solvents. Concentrated glucose medium was also fermented. The C. beijerinckii BA101 mutant strain was not negatively affected by the pervaporative conditions. In the integrated experiment, acids were not produced. With the active fermentation broth, butanol selectivity was reduced by a factor of 2-3. However, the membrane flux was not affected by the active fermentation broth. The butanol permeate concentration ranged from 26.4 to 95.4 g/L, depending upon butanol concentration in the fermentation broth. Since the permeate of most membranes contains acetone, butanol, and ethanol (and small concentrations of acids), it is suggested that distillation be used for further purification.     

A media design program for lactic acid production coupled with extraction by electrodialysis

The aim of this study was to investigate industrial media for lactic acid fermentation to reduce the cost of nitrogen sources. Corn steep liquor (CSL) was successfully used at 5% (v/v) in batch fermentations. Use of soluble CSL improved the productivity approximately 20% with an advantage of clearer fermentation broth. Yeast extract (YE)-complemented CSL media further increased the productivity. It was found that 3.1 g L(-1) yeast extract and 5% CSL could be an effective substitute for 15 g L(-1) yeast extract in 10% glucose medium. Spent brewery yeast was also used as a sole nitrogen source equivalent to 5% CSL. Lactic acid was recovered by electrodialysis from the cell free broth. Depleted cell free broth supplemented with 5 g L(-1) of yeast extract performed reasonably in batch cultures. Reuse of the fermentation broth may reduce the cost of raw materials as well as minimize the fermentation wastes.     

Reactive extraction of penicillin G in a pilot plant Karr-column

Summary Penicillin G was extracted from a model medium with a secondary amine (Amberlite LA-2) as carrier in n-butylacetate as solvent in a 7.6 m high pilot plant Karr-column at different stroke frequencies, throughput of the phases, concentrations of Penicillin G and carrier and ratios of the throughputs of the aqueous and organic phases. Up to penicillin concentrations of 30 gl^–1, throughputs of the aqueous phase of 100 lh^–1 and throughput ratios of the aqueous phase-to-organic phase of 3, very high degrees of extraction (99%) can be achieved with a penicillin loss below 1%.Symbols a specific interfacial area with regard to the volume of the continuous phase - C partition coefficient - cA, cA, i concentration of carrier (sec. amine) in the bulk at the interface - cAHP, cAHP, i concentration of complex in the bulk at the interface - cH proton concentration - cHP_a, cHP_a,i concentration of free acid in the bulk of the aqueous phase at the interface - cHP_o, cHP_{o, i} concentration of free acid in the bulk of the organic phase, at the interface - cP, cP, i concentration of acid anions in the bulk of the aqueous phase, at the interface - d₃₂ Sauter droplet diameter - E degree of extraction - f stroke frequency - KG reaction equilibrium constant - K_phys distribution coefficient - N number of stages in cascade - t mean residence time of the aqueous phase - _aq throughput of the aqueous phase - _o throughput of the organic phase - Z dimensionless longitudinal coordinate of the column with regard to its active length (4 m) - holdup of the organic phase     

Glycerol production by microbial fermentation: a review

Microbial production of glycerol has been known for 150 years, and glycerol was produced commercially during World War I. Glycerol production by microbial synthesis subsequently declined since it was unable to compete with chemical synthesis from petrochemical feedstocks due to the low glycerol yields and the difficulty with extraction and purification of glycerol from broth. As the cost of propylene has increased and its availability has decreased especially in developing countries and as glycerol has become an attractive feedstock for production of various chemicals, glycerol production by fermentation has become more attractive as an alternative route. Substantial overproduction of glycerol by yeast from monosaccharides can be obtained by: (1) forming a complex between acetaldehyde and bisulfite ions thereby retarding ethanol production and restoring the redox balance through glycerol synthesis; (2) growing yeast cultures at pH values near 7 or above; or (3) using osmotolerant yeasts. In recent years, significant improvements have been made in the glycerol production using osmotolerant yeasts on a commercial scale in China. The most outstanding achievements include: (1) isolation of novel osmotolerant yeast strains producing up to 130 g/L glycerol with yields up to 63% and the productivities up to 32 g/(L day); (2) glycerol yields, productivities and concentrations in broth up to 58%, 30 g/(L day) and 110-120 g/L, respectively, in an optimized aerobic fermentation process have been attained on a commercial scale; and (3) a carrier distillation technique with a glycerol distillation efficiency greater than 90% has been developed. As glycerol metabolism has become better understood in yeasts, opportunities will arise to construct novel glycerol overproducing microorganisms by metabolic engineering.     

Extractive fermentation for butyric acid production from glucose by Clostridium tyrobutyricum

A novel extractive fermentation for butyric acid production from glucose, using immobilized cells of Clostridium tyrobutyricum in a fibrous bed bioreactor, was developed by using 10% (v/v) Alamine 336 in oleyl alcohol as the extractant contained in a hollow-fiber membrane extractor for selective removal of butyric acid from the fermentation broth. The extractant was simultaneously regenerated by stripping with NaOH in a second membrane extractor. The fermentation pH was self-regulated by a balance between acid production and removal by extraction, and was kept at approximately pH 5.5 throughout the study. Compared with conventional fermentation, extractive fermentation resulted in a much higher product concentration (>300 g/L) and product purity (91%). It also resulted in higher reactor productivity (7.37 g/L. h) and butyric acid yield (0.45 g/g). Without on-line extraction to remove the acid products, at the optimal pH of 6.0, the final butyric acid concentration was only approximately 43.4 g/L, butyric acid yield was 0.423 g/g, and reactor productivity was 6.77 g/L. h. These values were much lower at pH 5.5: 20.4 g/L, 0.38 g/g, and 5.11 g/L. h, respectively. The improved performance for extractive fermentation can be attributed to the reduced product inhibition by selective removal of butyric acid from the fermentation broth. The solvent was found to be toxic to free cells in suspension, but not harmful to cells immobilized in the fibrous bed. The process was stable and provided consistent long-term performance for the entire 2-week period of study.     

New reactive extraction systems for separation of bio-succinic acid

Biotechnologically produced succinic acid has the potential to displace maleic acid and its uses and to become an important feedstock for the chemical industry. In addition to optimized production strains and fermentation processes, an efficient separation of succinic acid from the aqueous fermentation broth is indispensable to compete with the current petrochemical production processes. In this context, high molecular weight amines are known to be effective extractants for organic acids. For this reason, as a first step of isolation and purification, the reactive extraction of succinic acid was studied by mixing aqueous succinic acid solutions with 448 different amine–solvent mixtures as extraction agents (mixer-settler studies). The extraction agents consist either of one amine and one solvent (208 reactive extraction systems) or two amines and two solvents (240 reactive extraction systems). Maximum extraction yields of succinic acid from an aqueous solution with 423 mM succinic acid at pH 2.0 were obtained with more than 95% yield with trihexylamine solved in 1-octanol or with dihexylamine and diisooctylamine solved in 1-octanol and 1-hexanol. Applying these optimized reactive extraction systems with Escherichia coli fermentation broth resulted in extraction yields of 78–85% due to the increased ionic strength of the fermentation supernatant and the co-extraction of other organic acids (e.g., lactic acid and acetic acid), which represent typical fermentation byproducts.     

Reactive extraction of penicillin G in a pilot plant Karr-column II. Fermentation broths

Summary Penicillin G was extracted from mycelfree fermentation broths by means of the carrier (Amberlite LA-2) in n-butylacetate at pH 5 in a 7.6 m high pilot plant Karr-column with degrees of extraction E=98–99% and penicillin enrichments up to 3. The reextraction was carried out with phosphate buffer at pH-values above 7.5 with degree of extractions E=86–88% and penicillin enrichments up to 3. The penicillin and carrier losses were negligible. The influence of the process variables on the extraction degree was investigated. The penicillin extraction of the model medium and the fermentation broths were compared. Recommendations are given for the optimal penicillin recovery with reactive extraction.Symbols a specific interfacial area with regard to the volume of the continuous phase - cA concentration of carrier - cAHP,O concentration of complex in feed - cP,cP,O concentration of penicillin acid anion in theaqueous phase, in the feed - d ₃₂ Sauter droplet diameter - E degree of extraction - f stroke frequency - V _aq throughput of the aqueous phase - V ₀ throughput of the organic phase - Z dimensionsless longitudinal coordinate of the column with regard to its active length (4m) - holdup of the organic phase     

Ethanol production by Kluyveromyces lactis immobilized cells in copolymer carriers produced by radiation polymerization

The conditions for batch and continuous production of ethanol, using immobilized growing yeast cells of Kluyveromyces lactis, have been optimized. Yeast cells have been immobilized in hydrogel copolymer carriers composed of polyvinyl alcohol (PVA) with various hydrophilic monomers, using radiation copolymerization technique. Yeast cells were immobilized through adhesion and multiplication of yeast cells themselves. The ethanol production of immobilized growing yeast cells with these hydrogel carriers was related to the monomer composition of the copolymers and the optimum monomer composition was hydroxyethyl methacrylate (HEMA). In this case by using batch fermentation, the superior ethanol production was 32.9 g L(-1) which was about 4 times higher than that of cells in free system. The relation between the activity of immobilized yeast cells and the water content of the copolymer carriers was also discussed. Immobilized growing yeast cells in PVA: HEMA (7%: 10%, w/w) hydrogel copolymer carrier, were used in a packed-bed column reactor for the continuous production of ethanol from lactose at different levels of concentrations (50, 100 and 150) g L(-1). For all lactose feed concentrations, an increase in dilution rates from 0.1 h(-1) to 0.3 h(-1) lowered ethanol concentration in fermented broth, but the volumetric ethanol productivity and volumetric lactose uptake rate were improved. The fermentation efficiency was lowered with the increase in dilution rate and also at higher lactose concentration in feed medium and a maximum of 70.2% was obtained at the lowest lactose concentration 50 g L(-1).     

三相流化床中固定化米根霉萃取发酵生产L-乳酸

以TRPO／磺化煤油为萃取剂,在2L三相流床反应器中进行了固定化米根霉原位萃取和异位萃取发酵生产L-乳酸的实验,结果表明,发酵液中的pH值能被控制在3．5左右．产酸速率高达每小时．每1L固定化颗粒产生11gL-乳酸。提出了一个数学模型用以描述萃取发酵中L-乳酸的积累及在各相的分配情况。模型计算曲线与实验值符合良好。     

Salting-out extraction and crystallization of succinic acid from fermentation broths

In this study, salting-out extraction (SOE) and crystallization were combined to recover succinic acid from fermentation broths. Of the different SOE systems investigated, the system consisting of organic solvents and acidic salts appeared to be more favorable. A system using acetone and ammonium sulfate was investigated to determine the effect of phase composition and pH. The highest partition coefficient (8.64) and yield of succinic acid (90.05%) were obtained by a system composed of 30% (w/w) acetone and 20% (w/w) ammonium sulfate at a pH of 3.0. Additionally, 99.03% of cells, 90.82% of soluble proteins, and 94.89% of glucose could be simultaneously removed from the fermentation broths. Interestingly, nearly 40% of the pigment was removed using the single-step salting-out extraction process. The analysis of the effect of pH on salting-out extraction indicates that a pH lower than the pK of succinic acid is beneficial for the recovery of succinic acid in an SOE system. Crystallization was performed for the purification of succinic acid at 4 °C and pH 2.0. By combining salting-out extraction with crystallization, an identical total yield (65%) and a higher purity (97%) of succinic acid were obtained using a synthetic fermentation broth compared with the actual fermentation broth (65% and 91%, respectively).     

Effect of salts on the extraction characteristics of succinic acid by predispersed solvent extraction

Predispersed solvent extraction (PDSE) of succinic acid with Tri-n-octylamine (TOA) dissolved in 1-octanol from aqueous solutions of 50 g/L succinic acid was examined. It was found that the equilibrium data in PDSE was equal to that in conventional solvent extraction in spite of the lack of mechanical mixing in PDSE. The influence of salts on succinic acid extraction and the stability of colloidal liquid aphrons (CLAs) were also investigated. Results indicated that in the presence of sodium chloride, less succinic acid was extracted by CLAs and the stability of CLAs decreased. However, the stability of CLAs was sufficient to make PDSE practically applicable to real fermentation broth, considering the concentration range of salts in the fermentation process for succinic acid.     

Ethanol production from xylose with the yeast Pichia stipitis and simultaneous product recovery by gas stripping using a gas-lift loop fermentor with attached side-arm (GLSA)

The bioconversion of xylose into ethanol with the yeast Pichia stipitis CBS 5773 is inhibited when 20 g/L of ethanol are present in the fermentation broth. In order to avoid this limitation, the fermentation was carried out with simultaneous recovery of product by CO(2) stripping. The fermentation was also improved by attaching a side-arm to the main body of a classical gas-lift loop fermentor. This side-arm increases the liquid circulation, mass transfer, and gas distribution, reducing the amount of oxygen in the inlet gas necessary to perform the fermentation of xylose under microaerobic conditions (K(L)a approximately 16 h(-1)). The continuous stripping of ethanol from the fermentation broth in this new bioreactor system allowed the consumption of higher xylose concentrations than using Erlenmeyer shaker flasks, improved significantly the process productivity and provided a clean ethanol solution by using an ice-cooled condenser system. Finally, a fed-batch fermentation was carried out with a K(L)a = 15.8 h(-1). Starting with 248.2 g of xylose, 237.6 g of xylose was consumed to produce 88.1 g of ethanol which represents 72.6% of the theoretical yield (47.2 g/L of ethanol was recovered in the condenser, while 9.6 g/L remained in the fermentation broth).     

发酵液中多拉菌素的提取和萃取条件研究

采用单因素实验,分别研究提取试剂、发酵液放置时间、pH值和温度对发酵液中多拉菌素提取效果的影响;然后以乙酸乙酯为萃取试剂,研究萃取次数及萃取体积对多拉菌素萃取效果的影响。结果显示,甲醇为最佳提取试剂;发酵液在pH为3～11、温度为20～80℃的条件下放置144 h,多拉菌素均能稳定存在,提取得到的多拉菌素的质量浓度没有显著变化;浓缩提取液液经2倍体积乙酸乙酯萃取2次即可。该条件下多拉菌素的质量浓度和萃取率分别为151.78μg/mL和98.00%。     

Production of <Emphasis Type="Italic">Pleurotus sajor-caju</Emphasis> strain PS-2001 biomass in submerged culture

Mushrooms or fruiting bodies of many basidiomycetes are commonly produced in solid-state fermentation, generally after 20-60 days of growth. However, it is also possible to produce biomass from these fungi, in submerged fermentation in shorter time. This work was aimed at evaluating biomass production with the basidiomycete Pleurotus sajor-caju, in a submerged process and to determine the proportion of chemical components of this biomass. Initially, an optimization of the culture medium was done to produce a faster growth of microbial mass by changing the concentrations of ammonium sulfate, soy protein and yeast extract. Using the optimized culture medium, values of approximately 5.5 g L(-1) of biomass in a medium with 10 g L(-1) of glucose were attained. When the optimized culture medium was tested in a 5-L stirred tank bioreactor, using 10 g L(-1) of glucose or sucrose as carbon source, values of 8.18 and 5.94 g L(-1) of biomass concentration were obtained, respectively. In the medium with glucose, high yields (0.82 g g(-1)) and productivity of 0.085 g L(-1) h(-1) were obtained. The exopolysaccharide content (1.58 g dry matter L(-1)) in the culture was higher in the fermentation with sucrose. The nutritional composition of the biomass obtained in the submerged fermentation was similar to that of the fruiting body in terms of quantities of total carbohydrates, ash and calories, but total fat and protein were higher.     

Simultaneous clostridial fermentation,lipase‐catalyzed esterification,and ester extraction to enrich diesel with butyl butyrate

The recovery of 1‐butanol from fermentation broth is energy‐intensive since typical concentrations in fermentation broth are below 20 g L^?1. To prevent butanol inhibition and high downstream processing costs, we aimed at producing butyl esters instead of 1‐butanol. It is shown that it is possible to perform simultaneously clostridial fermentation, esterification of the formed butanol to butyl butyrate, and extraction of this ester by hexadecane. The very high partition coefficient of butyl butyrate pulls the esterification towards the product side even at fermentation pH and relatively low butanol concentrations. The hexadecane extractant is a model diesel compound and is nontoxic to the cells. If butyl butyrate enriched diesel can directly be used as car fuel, no product recovery is required. A proof‐of‐principle experiment for the one‐pot bio‐ester production from glucose led to 5 g L^?1 butyl butyrate in the hexadecane phase. The principle may be extended to a wide range of esters, especially to longer chain ones. Biotechnol. Bioeng. 2013; 110: 137–142. © 2012 Wiley Periodicals, Inc.     

自絮凝酵母SPSC01在组合反应器系统中酒精连续发酵的研究

建立了一套由四级磁力搅拌发酵罐串联组成、总有效容积4000mL的小型组合生物反应器系统 ,其中一级罐作为种子培养罐。以脱胚脱皮玉米粉双酶法制备的糖化液为种子培养基和发酵底物 ,进行了自絮凝颗粒酵母酒精连续发酵的研究。种子罐培养基还原糖浓度为100g L ,添加 (NH₄)₂HPO₄ 和KH₂PO₄ 各 20g L ,以0.017h^-1 的恒定稀释速率流加 ,并溢流至后续酒精发酵系统。发酵底物初始还原糖浓度 220g/L ,添加 (NH₄)₂HPO₄ 15g/L和KH₂PO₄2 5g/L ,流加至第一级发酵罐 ,稀释速率分别为 0.017、0.025、0.033、0.040和0.05 0h^-1。实验数据表明 ,自絮凝颗粒酵母在各发酵罐中呈部分固定化状态 ,在稀释速率0.040h^-1 条件下 ,发酵系统呈一定的振荡行为 ,其他四个稀释速率实验组均能够达拟稳态。当稀释速率不超过 0 0 33h^-1 ,流出末级发酵罐的发酵液中酒精浓度可以达到 12 % (V/V)以上 ,残还原糖和残总糖分别在 0 11%和 0 35 % h^-1,流出末级发酵罐的发酵液中酒精浓度可以达到12%（V/V）以上,残还原糖和残总糖分别在0.11%和0.35%（W/V）以下。在稀释速率为0.033h^-1时,计算发酵系统酒精的设备生产强度指标为3.32（g·L^-1·h^-1）,与游离酵母细胞传统酒精发酵工艺相比,增加约1倍。