Effects of carbon and oxygen limitations and calcium concentrations on biofilm removal processes

Bacterial biofilm removal processes due to shear and catastrophic sloughing have been investigated in a turbulent flow system under conditions of carbon versus oxygen substrate limitations and varying aqueous phase calcium concentrations. Biofilm cellular and extracellular polymer carbon, total biofilm carbon and mass, and biofilm calcium concentrations are measured for pure culture biofilms of the facultative aerobe, Pseudomonas putida ATCC 11172. Results indicate oxygen-limited biofilms reach a higher steady-state biofilm organic carbon level than carbon-limited biofilms. Oxygen-limited biofilms also exhibit (1) a higher extracellular polymer-carbon: cell-carbon ratio throughout biofilm development and (2) a higher biofilm calcium content than carbon-limited biofilms. Increasing aqueous phase calcium concentrations increase the amount of biofilm calcium in both cases; the rate of calcium accumulation in oxygen-limited biofilms increases with increasing liquid phase calcium concentrations over the entire range studied while the rates of calcium accumulation in carbon-limited biofilms appear independent of aqueous phase calcium concentrations above 11.0 mg/L. Oxygen-limited biofilms with their higher extracellular polymer and calcium content exhibit shear removal rates that are 20-40% of those observed for carbon-limited biofilms. However, it is the oxygen-limited biofilms that experience catastrophic sloughing events. The carbon-limited biofilms studied here never sloughed even if subjected to intentional long-term deprivation of all nutrients. Reduced shear removal and the susceptibility to sloughing of the oxygen-limited biofilms are attributed to their more cohesive structure bought about by their relatively greater extracellular polymer production.     

Activity of Pseudomonas aeruginosa in biofilms: effect of calcium

Aerobic glucose metabolism by Pseudomonas aeruginosa biofilms at various calcium loading rates was investigated. The influence of calcium on specific growth rate, extracellular polymeric substance (EPS) formation rate, biofilm detachment rate, and biofilm calcium concentrations was determined. Calcium accumulated in the biofilm in proportion to the liquid phase concentration. Increasing calcium concentration increased the cohesiveness of the biofilm as indicated by a lower relative detachment rate. Specific activity in the biofilm was the same as that measured in a chemostat and was not influenced by changing calcium concentration. EPS formation rate in the biofilm was unaffected by calcium concentration but was higher than that observed in a chemostat.     

Startup of anaerobic downflow stationary fixed film (DSFF) reactors

One of the serious problems limiting the application of full-scale anaerobic fixed film processes is reactor startup. To better understand startup, studies with downflow stationary fixed film (DSFF) reactors were conducted to characterize the effects of influent concentration, support material, and surface-to-volume ratio on biofilm development and overall reactor performance. Materials with roughened surfaces gave the best startup performance and as expected increased surface area in the reactors led to more rapid increases in loading rates and higher ultimate loadings. Soluble influent COD concentrations between 5 x 10(3) and 2 x 10(4) mg/L influenced the rate of biofilm development. Lower COD concentrations resulted in faster development of the biofilm, even though ultimate loadings were not necessarily achieved as rapidly as in reactors fed higher strength wastes. No decrease in specific activity of the biofilms in each reactor was observed as the thickness of the biofilms increased to their maximum value at the ultimate loadings. The operation of reactors fed lower strength wastes was more stable than reactors receiving higher strength feeds at comparable loadings. Biofilm yield and activity, COD removals, suspended growth and activity, and other system parameters are discussed.     

Effect of oxidizing and non-oxidizing biocides on biofilm at different substrate levels in the model recirculating cooling water system

With the reducing of water resources, using advanced treated refinery wastewater as recirculating cooling water is an effective method to save water and to reduce the pollution of petroleum and petrochemical industry. However, the control of biofilm is a bottleneck in the application of this technology. To resolve the problem of biofilm formation and development, antimicrobial characteristics of chlorine dioxide and benzyldimethyldodecyl-ammonium chloride on biofilm at different substrate levels were investigated. Biofilm detachment ratio and TTC-dehydrogenase activity (DHA) were two indexes to discuss the antimicrobial effects. The results showed that at the high substrate level, the biofilms characteristics (biomass, the content of protein, polysaccharide and EPS) were the higher than those at the medium and low substrate levels, however biofilm’s DHA at the medium substrate level (12.97 μgTF/(g h)) was higher than those at the medium substrate level (7.64 μgTF/(g h)) and low substrate level (1.94 μgTF/(g h). The difference of substrate level in the media resulted in different biofilm structure. By contrast with the control experiment, biofilm detachment ratios were all increased in three media with ClO₂ and BDMDAC addition. After ClO₂ addition, MITs were 30, 120 and 240 min and MIC was 1, 4 and 6 mg/L, respectively, at the low, medium and high substrate level. After BDMDAC addition, MITs in three media were all longer than those after ClO₂ addition, MIC was 200, 300 and 400 mg/L, respectively, at the low, medium and high substrate level.     

The Role of Exopolymers Produced by Sphingomonas paucimobilis in Biofilm Formation and Composition

Exopolymers have been associated with the initial adhesion of bacteria, which is the primary step for biofilm formation. Moreover, the polymeric matrix of biofilms has a considerable influence on some of the most important physical and physiological properties of biofilms. The role of extracellular polymers in biofilm formation was studied using three mutants of Sphingomonas paucimobilis with increasing capabilities for exopolymer production. The physical, biochemical and physiological properties of three different layers of each biofilm were determined. The layers were detached by submitting the biofilm to increasing shear stress. The results revealed that the presence of exopolymers in the growth medium was essential for biofilm formation. The mutant producing the highest amount of exopolymer formed very thick biofilms, while the biofilms formed by the medium exopolymer producer were on average 8 times thinner. The lowest exopolymer producer did not form biofilm. In both types of biofilms, exopolymer density increased with depth, although this tendency was more significant in thinner biofilms. Cell distribution was also more heterogeneous in thinner biofilms, exhibiting a greater accumulation of cells in the inner layers. The thicker biofilms had very low activity in the inner layer. This was related to a high accumulation of proteins and DNA in this layer due to cell lysis and hydrolytic activity. Activity in the thin biofilm was constant throughout its depth, suggesting that there was no nutrient limitation. The production of exopolymers by each cell was constant throughout the depth of the biofilms, although it was greater in the case of the higher producer.     

Biofilm detachment mechanisms in a liquid-fluidized bed

Bed fluidization offers the possibility of gaining the advantages of fixed-film biological processes without the disadvantage of pore clogging. However, the biofilm detachment rate, due to hydrodynamics and particle-to-particle attrition, is very poorly understood for fluidized-bed biofilm processes. In this work, a two-phase fluidized-bed biofilm was operated under a constant surface loading (0.09 mg total organic carbon/cm(2) day) and with a range of bed height (H), fluid velocities (U), and support-particle concentrations (C(p)). Direct measurements were made for the specific biofilm loss rate coefficient (b(s))and the total biofilm accumulation (X(f)L(f)). A hydrodynamic model allowed independent determination of the biofilm density (X(f)), biofilm thickness (L(f)), liquid shear stress (tau), and Reynolds number (Re). Multiple regression analysis of the results showed that increased particle-to-particle attrition, proportional to C(p) and increased turbulence, described by Re, caused the biofilms to be denser and thinner. The specific detachment rate coefficient (b(s)) increased as C(p) and Re increased. Almost all of the 6, values were larger than predicted by a previous model derived for smooth biofilms on a nonfluidized surface. Therefore, the turbulence and attrition of bed fluidization appear to be dominant detachment mechanisms.     

Sodium dodecyl sulfate allows the persistence and recovery of biofilms of Pseudomonas fluorescens formed under different hydrodynamic conditions

The effect of the anionic surfactant sodium dodecyl sulfate (SDS) on Pseudomonas fluorescens biofilms was investigated using flow cell reactors with stainless steel substrata, under turbulent (Re = 5200) and laminar (Re = 2000) flow. Steady-state biofilms were exposed to SDS in single doses (0.5, 1, 3 and 7 mM) and biofilm respiratory activity and mass measured at 0, 3, 7 and 12 h after the SDS application. The effect of SDS on biofilm mechanical stability was assessed using a rotating bioreactor. Whilst high concentrations (7 mM) of SDS promoted significant biofilm inactivation, it did not significantly reduce biofouling. Turbulent and laminar flow-generated biofilms had comparable susceptibility to SDS application. Following SDS exposure, biofilms rapidly recovered over the following 12 h, achieving higher respiratory activity values than before treatment. This phenomenon of post-treatment recovery was more pronounced for turbulent flow-generated biofilms, with an increase in SDS concentration. The mechanical stability of the biofilms increased with surfactant application, except for SDS concentrations near the critical micellar concentration, as measured by biofilm removal due to an increase in external shear stress forces. The data suggest that although SDS exerts antimicrobial action against P. fluorescens biofilms, even if only partial and reversible, it had only limited antifouling efficacy, increasing biofilm mechanical stability at low concentrations and allowing significant and rapid recovery of turbulent flow-generated biofilms.     

The <Emphasis Type="Italic">in vitro</Emphasis> and <Emphasis Type="Italic">in vivo</Emphasis> efficacy of fluconazole in combination with farnesol against <Emphasis Type="Italic">Candida albicans</Emphasis> isolates using a murine vulvovaginitis model

Farnesol is a quorum-sensing molecule that inhibits biofilm formation in Candida albicans. Previous in vitro data suggest that, in combination with certain antifungals, farnesol may have an adjuvant anti-biofilm agent. However, the in vivo efficacy of farnesol is very questionable. Therefore, the in vitro and in vivo activity of fluconazole combined with farnesol was evaluated against C. albicans biofilms using fractional inhibitory concentration index (FICI) determination, time-kill experiments and a murine vulvovaginitis model. The median biofilm MICs of fluconazole-sensitive C. albicans isolates ranged between 4 -> 512 mg/L and 150–300 μM for fluconazole and farnesol, respectively. These values were 512 -> 512 mg/L and > 300 μM for fluconazole-resistant clinical isolates. Farnesol decreased the median MICs of fluconazole by 2-64-fold for biofilms. Based on FICI, synergistic interaction was observed only in the case of the sessile SC5314 reference strain (FICIs: 0.16–0.27). In time-kill studies, only the 512 mg/L fluconazole and 512 mg/L fluconazole + 75 μM farnesol reduced biofilm mass significantly at each time point in the case of all isolates. The combination reduced the metabolic activity of biofilms for all isolates in a concentration- and time-dependent manner. Our findings revealed that farnesol alone was not protective in a murine vulvovaginitis model. Farnesol was not beneficial in combination with fluconazole for fluconazole-susceptible isolates, but partially increased fluconazole activity against one fluconazole-resistant isolate, but not the other one.     

Degradation of phenol by Pseudomonas putida ATCC 11172 in continuous culture at different ratios of biofilm surface to culture volume

Pseudomonas putida ATCC 11172 was grown in continuous culture with phenol as the only carbon and energy source; a culture practically without biofilm was compared with biofilm cultures of differing surface area/volume ratios. The biofilm did not significantly affect the maximal suspended cell concentration in the effluent, but it increased the maximal phenol reduction rate from 0.23 g/liter per h (without biofilm) to 0.72 g/liter per h at the highest biofilm level (5.5 cm2 of biofilm surface per ml of reactor volume). The increase in phenol reduction rate was linear up to the surface area/volume ratio of 1.4 cm2/ml. The continuous cultures with biofilms could tolerate a higher phenol concentration of the medium (3.0 g/liter) than the nonbiofilm system (2.5 g/liter). At higher dilution rates an intermediate product, 2-hydroxymuconic semialdehyde, accumulated in the culture. When the biomass of the effluent started to decrease, the concentration of 2-hydroxymuconic semialdehyde reached a peak value. We conclude that biofilms in continuous culture have the potential to enhance the aerobic degradation of aromatic compounds.     

Degradation of phenol by Pseudomonas putida ATCC 11172 in continuous culture at different ratios of biofilm surface to culture volume.

Pseudomonas putida ATCC 11172 was grown in continuous culture with phenol as the only carbon and energy source; a culture practically without biofilm was compared with biofilm cultures of differing surface area/volume ratios. The biofilm did not significantly affect the maximal suspended cell concentration in the effluent, but it increased the maximal phenol reduction rate from 0.23 g/liter per h (without biofilm) to 0.72 g/liter per h at the highest biofilm level (5.5 cm2 of biofilm surface per ml of reactor volume). The increase in phenol reduction rate was linear up to the surface area/volume ratio of 1.4 cm2/ml. The continuous cultures with biofilms could tolerate a higher phenol concentration of the medium (3.0 g/liter) than the nonbiofilm system (2.5 g/liter). At higher dilution rates an intermediate product, 2-hydroxymuconic semialdehyde, accumulated in the culture. When the biomass of the effluent started to decrease, the concentration of 2-hydroxymuconic semialdehyde reached a peak value. We conclude that biofilms in continuous culture have the potential to enhance the aerobic degradation of aromatic compounds.     

Nonuniform spatial patterns of respiratory activity within biofilms during disinfection.

Fluorescent stains in conjunction with cryoembedding and image analysis were applied to demonstrate spatial gradients in respiratory activity within bacterial biofilms during disinfection with monochloramine. Biofilms of Klebsiella pneumoniae and Pseudomonas aeruginosa grown together on stainless steel surfaces in continuous-flow annular reactors were treated with 2 mg of monochloramine per liter (influent concentration) for 2 h. Relatively little biofilm removal occurred as evidenced by total cell direct counts. Plate counts (of both species summed) indicated an average 1.3-log decrease after exposure to 2 mg of monochloramine per liter. The fluorogenic redox indicator 5-cyano-2,3-ditolyl tetrazolium chloride (CTC) and the DNA stain 4',6-diamidino-2-phenylindole (DAPI) were used to differentiate respiring and nonrespiring cells in biofilms. Epifluorescence micrographs of frozen biofilm cross sections clearly revealed gradients of respiratory activity within biofilms in response to monochloramine treatment. These gradients in specific respiratory activity were quantified by calculating the ratio of CTC and DAPI intensities measured by image analysis. Cells near the biofilm-bulk fluid interface lost respiratory activity first. After 2 h of biocide treatment, greater respiratory activity persisted deep in the biofilm than near the biofilm-bulk fluid interface.     

Sugar composition of biofilms produced by paper mill bacteria

Biofilms of paper mill bacteria were cultivated in paper mill white water-simulating conditions on glass slides or stainless steel coupons in a laboratory culture system. The sugar content and composition of the biofilms were analysed and compared with the sugar composition of paper mill slimes. Acid methanolysis followed by gas chromatography revealed that Burkholderia was the major biofilm producer in pure culture, producing up to 50 microg of biofilm sugar cm(-2) in 5 days in rich medium and 10 microg in paper mill simulating medium. A mixture of simulated paper mill water with a culture medium yielded more biofilm (100 microg cm(-2)) than either of the media alone, so the biofilm accumulation was not proportional to the available substrate. More biofilm accumulated on stainless steel coupons than on glass slides, and the steel-coupon biofilms contained slightly more uronic acids. The biofilm sugars contained mainly galactose, glucose, mannose, and rhamnose. In paper mill medium, the Burkholderia biofilm contained more galactose and glucose, and less rhamnose, than in rich laboratory medium. The sugar composition of paper mill slimes was quite similar to those of steel-cultured Burkholderia cepacia biofilms. This suggests that Burkholderia cepacia is responsible for much of the slime in the paper mill.     

Methanotrophic attached-film reactor development and biofilm characteristics

The feasibility of using methanotrophs in an attached-film, fluidized-bed (MAFFB) reactor system has been under investigation since 1987. Mixed culture, methane-utilizing attached biofilms were developed on diatomaceous earth particles and on granular activated carbon. The required feed gases, methane and oxygen, were supplied to the attached biofilm in disolved form using separate gas-liquid aeration columns. Biofilm growth was steady despite low influent dissolved methane concentrations (1 to 3 mg/L). A breeder MAFFB operated consistently for 4.1 years with attached biofilm concentrations as high as 51.7 g VS/L static-bed with minimal biomass wasting and with minimal buffer and nutrient inputs. The maximum biomass concentration observed was 75.6 g VS/L static-bed in a MAFFB reactor treating trichloroethene. Biofilm thickness reached 160 mum with typical values of 70 mum under methane and oxygen growht-rate-limited conditions. Biofilm densities of 120 to 190 g VS/L film were observed. Growth rates varied from <0.01/d to 0.17/d. Greater than 90% of the biomass concentration in the bed was attached, and effluent total suspended solids ranged from 5 to 74 mg/L, with an average of 24 mg/L over 27 runs in four MAFFB systems at upflow velocities of 11.4 to 25 m/h. Heterotrophic attached-film methanotrophs appear to be stable and useful for applications in toxics treatment, and other product manipulations. (c) 1992 John Wiley & Sons, Inc.     

The effects of glutaraldehyde on the control of single and dual biofilms of Bacillus cereus and Pseudomonas fluorescens

Glutaraldehyde (GLUT) was evaluated for control of single and dual species biofilms of Bacillus cereus and Pseudomonas fluorescens on stainless steel surfaces using a chemostat system. The biofilms were characterized in terms of mass, cell density, total and matrix proteins and polysaccharides. The control action of GLUT was assessed in terms of inactivation and removal of biofilm. Post-biocide action was characterized 3, 7, 12, 24, 48 and 72 h after treatment. Tests with planktonic cells were also performed for comparison. The results demonstrated that in dual species biofilms the metabolic activity, cell density and the content of matrix proteins were higher than those of either single species. Planktonic B. cereus was more susceptible to GLUT than P. fluorescens. The biocide susceptibility of dual species planktonic cultures was an average of each single species. Planktonic cells were more susceptible to GLUT than their biofilm counterparts. Biofilm inactivation was similar for both of the single biofilms while dual biofilms were more resistant than single species biofilms. GLUT at 200 mg l(-1) caused low biofilm removal (<10%). Analysis of the post-biocide treatment data revealed the ability of biofilms to recover their activity over time. However, 12 h after biocide application, sloughing events were detected for both single and dual species biofilms, but were more marked for those formed by P. fluorescens (removal >40% of the total biofilm). The overall results suggest that GLUT exerts significant antimicrobial activity against planktonic bacteria and a partial and reversible activity against B. cereus and P. fluorescens single and dual species biofilms. The biocide had low antifouling effects when analysed immediately after treatment. However, GLUT had significant long-term effects on biofilm removal, inducing significant sloughing events (recovery in terms of mass 72 h after treatment for single biofilms and 42 h later for dual biofilms). In general, dual species biofilms demonstrated higher resistance and resilience to GLUT exposure than either of the single species biofilms. P. fluorescens biofilms were more susceptible to the biocide than B. cereus biofilms.     

The impacts of the AOC concentration on biofilm formation under higher shear force condition

The logistic growth model was applied in the study to evaluate the impacts of assimilable organic carbon (AOC) concentration on the growth characteristics of biofilm and bulk bacteria under high flow velocity condition. The experimental results showed that there existed a growth and decline relation between biofilm and bulk bacteria at the low (0.05 mg/L) and medium (0.5 mg/L) AOC levels. Increasing the AOC concentration up to 1.0 mg/L, it resulted in high amounts of biofilm and bulk bacteria simultaneously. Although the carrying capacity of biofilm bacteria at the medium condition of AOC level was substantially reduced, the specific growth rate (GR) of biofilm bacteria was largest at this condition. It showed that the reduction of biofilm bacteria quantity did not represent the suppression of bacterial growth. The quantity of bulk water bacteria was obviously dependent with the quantity of biofilm bacteria and the increase of free bacteria with time in networks was mainly due to the growth and detachment of biofilm bacteria, not due to the growth of free bacteria themselves. The maximum growth rate of biofilm bacteria was increased upon increasing the AOC level. It indicated that the AOC level was an important factor affecting the growth of biofilm bacteria.     

Impact of flow velocity on the dynamic behaviour of biofilm bacteria

The impact of flow velocity (FV) on the growth dynamics of biofilms and bulk water heterotrophic plate count (HPC) bacteria in drinking water distribution systems was quantified and modeled by combining a logistic growth model with mass balance equations. The dynamic variations in the specific growth and release rates of biofilm bacteria were also quantified. The experimental results showed that the maximum biofilm biomass did not change when flow velocity was increased from 20 to 40 cm s(-1), but was significantly affected when flow velocity was further increased to 60 cm s(-1). Although the concentration of biofilm bacteria was substantially reduced by the higher shear stress, the concentration of bacteria in the bulk fluid was slightly increased. From this it is estimated that the specific growth rate and specific release rate of biofilm bacteria had doubled. The specific release (detachment) rate was dependent on the specific growth rate of the biofilm bacteria.     

Planktonic replication is essential for biofilm formation by Legionella pneumophila in a complex medium under static and dynamic flow conditions

Legionella pneumophila persists for a long time in aquatic habitats, where the bacteria associate with biofilms and replicate within protozoan predators. While L. pneumophila serves as a paradigm for intracellular growth within protozoa, it is less clear whether the bacteria form or replicate within biofilms in the absence of protozoa. In this study, we analyzed surface adherence of and biofilm formation by L. pneumophila in a rich medium that supported axenic replication. Biofilm formation by the virulent L. pneumophila strain JR32 and by clinical and environmental isolates was analyzed by confocal microscopy and crystal violet staining. Strain JR32 formed biofilms on glass surfaces and upright polystyrene wells, as well as on pins of "inverse" microtiter plates, indicating that biofilm formation was not simply due to sedimentation of the bacteria. Biofilm formation by an L. pneumophila fliA mutant lacking the alternative sigma factor sigma(28) was reduced, which demonstrated that bacterial factors are required. Accumulation of biomass coincided with an increase in the optical density at 600 nm and ceased when the bacteria reached the stationary growth phase. L. pneumophila neither grew nor formed biofilms in the inverse system if the medium was exchanged twice a day. However, after addition of Acanthamoeba castellanii, the bacteria proliferated and adhered to surfaces. Sessile (surface-attached) and planktonic (free-swimming) L. pneumophila expressed beta-galactosidase activity to similar extents, and therefore, the observed lack of proliferation of surface-attached bacteria was not due to impaired protein synthesis or metabolic activity. Cocultivation of green fluorescent protein (GFP)- and DsRed-labeled L. pneumophila led to randomly interspersed cells on the substratum and in aggregates, and no sizeable patches of clonally growing bacteria were observed. Our findings indicate that biofilm formation by L. pneumophila in a rich medium is due to growth of planktonic bacteria rather than to growth of sessile bacteria. In agreement with this conclusion, GFP-labeled L. pneumophila initially adhered in a continuous-flow chamber system but detached over time; the detachment correlated with the flow rate, and there was no accumulation of biomass. Under these conditions, L. pneumophila persisted in biofilms formed by Empedobacter breve or Microbacterium sp. but not in biofilms formed by Klebsiella pneumoniae or other environmental bacteria, suggesting that specific interactions between the bacteria modulate adherence.     

Influence of biofilms on iron and manganese deposition in drinking water distribution systems

Although health risk due to discoloured water is minimal, such water continues to be the source of one of the major complaints received by most water utilities in Australia. Elevated levels of iron (Fe) and/or manganese (Mn) in bulk water are associated with discoloured water incidents. The accumulation of these two elements in distribution systems is believed to be one of the main causes for such elevated levels. An investigation into the contribution of pipe wall biofilms towards Fe and Mn deposition, and discoloured water events is reported in this study. Eight laboratory-scale reactors were operated to test four different conditions in duplicate. Four reactors were exposed to low Fe (0.05 mg l(-1)) and Mn (0.02 mg l(-1)) concentrations and the remaining four were exposed to a higher (0.3 and 0.4 mg l(-1) for Fe and Mn, respectively) concentration. Two of the four reactors which received low and high Fe and Mn concentrations were chlorinated (3.0 mg l(-1) of chlorine). The biological activity (measured in terms of ATP) on the glass rings in these reactors was very low (～1.5 ng cm(-2) ring). Higher concentrations of Fe and Mn in bulk water and active biofilms resulted in increased deposition of Fe and Mn on the glass rings. Moreover, with an increase in biological activity, an increase in Fe and Mn deposition was observed. The observations in the laboratory-scale experiments were in line with the results of field observations that were carried out using biofilm monitors. The field data additionally demonstrated the effect of seasons, where increased biofilm activities observed on pipe wall biofilms during late summer and early autumn were found to be associated with increased deposition of Fe and Mn. In contrast, during the cooler months, biofilm activities were a magnitude lower and the deposited metal concentrations were also significantly less (ie a drop of 68% for Fe and 86% for Mn). Based on the laboratory-scale investigations, detachment of pipe wall biofilms due to cell death or flow dynamics could release the entrapped Fe and Mn into the bulk water, which could lead to a discoloured water event. Hence, managing biofilm growth on drinking water pipelines should be considered by water utilities to minimize accumulation of Fe and Mn in distribution networks.     

Heterogeneous biofilm activity in a segregated anaerobic fluidized bed bioreactor

Bed segregation in a fluidized bed bioreactor profoundly influenced biofilm thickness and microbial activities of the biofilm along the bed height. Bioparticles coated with a thin biofilm, observed at the bottom of the reactor, had a higher specific activity in propylene glycol and n-propanol degradation than in thick biofilms developed at the top of the reactor. Although no significant difference was observed in specific activity for propionate and acetate along the reactor flow axis, more total propionate and acetate conversion occurred in regions of thicker biofilm accumulation.     

Modulation of poly-N-acetylglucosamine accumulation within mature Staphylococcus epidermidis biofilms grown in excess glucose

PNAG is a major component of Staphylococcus epidermidis biofilms involved in intercellular adhesion as well as in the interaction of the biofilm with components of the host immune response. Synthesis of PNAG has been found to be regulated by several environmental factors. In the present study, the effect of glucose metabolism-dependent culture medium acidification in PNAG accumulation was evaluated. Established S. epidermidis biofilms were allowed to grow in excess glucose with or without maintained pH conditions. PNAG accumulation in these biofilms was determined by flow cytometry and fluorescence microscopy using wheat germ agglutinin as a fluorescent probe. Biofilms grown in maintained pH conditions presented significantly higher amounts of this polymer as well as higher icaA expression than biofilms grown in acidic pH conditions. Moreover, PNAG accumulation in biofilms grown in non-maintained pH conditions occurred in association with cell death. Overall, we show that glucose metabolism by decreasing the culture pH affects biofilm physiology in respect to PNAG production and cell death. The reported in vitro modulation of PNAG accumulation within S. epidermidis biofilms further highlights the role of environment on determining the biofilm physiological state.