Nafion/lead nitroprusside nanoparticles modified carbon ceramic electrode as a novel amperometric sensor for l-cysteine

This work describes the electrochemical and electrocatalytic properties of carbon ceramic electrode (CCE) modified with lead nitroprusside (PbNP) nanoparticles as a new electrocatalyst material. The structure of deposited film on the CCE was characterized by energy dispersive X-ray (EDX), Fourier transform infrared (FTIR), and scanning electron microscopy (SEM). The cyclic voltammogram (CV) of the PbNP modified CCE showed two well-defined redox couples due to [Fe(CN)₅NO]³⁻/[Fe(CN)₅NO]²⁻ and Pb^IV/Pb^II redox reactions. The modified electrode showed electrocatalytic activity toward the oxidation of l-cysteine and was used as an amperometric sensor. Also, to reduce the fouling effect of l-cysteine and its oxidation products on the modified electrode, a thin film of Nafion was coated on the electrode surface. The sensor response was linearly changed with l-cysteine concentration in the range of 1 × 10⁻⁶ to 6.72 × 10⁻⁵ mol L⁻¹ with a detection limit (signal/noise ratio [S/N] = 3) of 0.46 μM. The sensor sensitivity was 0.17 μA (μM)⁻¹, and some important advantages such as simple preparation, fast response, good stability, interference-free signals, antifouling properties, and reproducibility of the sensor for amperometric determination of l-cysteine were achieved.     

Ultrasensitive DNA sensor based on gold nanoparticles/reduced graphene oxide/glassy carbon electrode

We have designed a simple and novel electrochemical biosensor based on glassy carbon electrode (GCE) for DNA detection. GCE was modified with reduced graphene oxide (RGO) and gold nanoparticles (AuNPs) by the electrochemical method, which is helpful for immobilization of thiolated bioreceptors. The electrode modification processes were characterized by scanning electron microscopy (SEM) and electrochemical methods. Then a single-stranded DNA (ssDNA) probe for BRCA1 5382 insC mutation detection was immobilized on the modified electrode for a specific time. The experimental conditions, such as probe immobilization time and target DNA (complementary DNA) hybridization time and temperature with probe DNA, were optimized using electrochemical methods. The electrochemical response for DNA hybridization and synthesis was measured using electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV) methods. The calibration graph contains two linear ranges; the first part is in the range of 3.0 × 10⁻²⁰ to 1.0 × 10⁻¹² M, and the second segment part is in the range of 1.0 × 10⁻¹² to 1.0 × 10⁻⁷ M. The biosensor showed excellent selectivity for the detection of the complementary sequences from noncomplementary sequences, so it can be used for detection of breast cancer.     

Nickel(II)-baicalein complex modified multiwall carbon nanotube paste electrode and its electrocatalytic oxidation toward glycine

A modified electrode, nickel(II)-baicalein complex modified multiwall carbon nanotube paste electrode (Ni(II)-BA-MWCNT-PE), has been fabricated by electrodepositing Ni(II)-BA complex on the surface of MWCNT-PE in alkaline solution. The Ni(II)-BA-MWCNT-PE exhibits the characteristic of improved reversibility and enhanced current responses of the Ni(III)/Ni(II) couple compared with Ni(II)-BA-carbon paste electrode (CPE). It also shows better electrocatalytic activity toward the oxidation of glycine than Ni(II)-MWCNT-PE. Kinetic parameters such as the electron transfer coefficient α, rate constant k_s of the electrode reaction, the diffusion coefficient D of glycine, and the catalytic rate constant k_cat of the catalytic reaction are determined. Moreover, the catalytic currents present linear dependence on the concentration of glycine from 20 μM to 1.0 mM by amperometry. The detection limit and sensitivity are 9.2 μM and 3.92 μA mM⁻¹, respectively. The modified electrode for glycine determination is of the property of simple preparation, fast response, and good stability.     

Electrochemical assay for the determination of nitric oxide metabolites using copper(II) chlorophyllin modified screen printed electrodes

This work presents a novel electrochemical assay for the collective measurement of nitric oxide (NO) and its metabolites nitrite (NO₂⁻) and nitrate (NO₃⁻) in volume miniaturized sample at low cost using copper(II) chlorophyllin (CuCP) modified sensor electrode. Zinc oxide (ZnO) incorporated screen printed carbon electrode (SPCE) was used as a host matrix for the immobilization of CuCP. The morphological changes of the ZnO and CuCP modified electrodes were investigated using scanning electron microscopy. The electrochemical characterization of CuCP–ZnO–SPCE exhibited the characteristic quasi-reversible redox peaks at the potential +0.06 V versus Ag/AgCl. This biosensor electrode showed a wide linear range of response over NO concentrations from 200 nM to 500 μM with a detection limit of 100 nM and sensitivity of 85.4 nA μM⁻¹. Furthermore, NO₂⁻ measurement showed linearity of 100 nM to 1 mM with a detection limit of 100 nM for NO₂⁻ and sensitivity of 96.4 nA μM⁻¹. Then, the concentration of NO₃⁻ was measured after its enzymatic conversion into NO₂⁻. Using this assay, the concentrations of NO, NO₂⁻, and NO₃⁻ present in human plasma samples before and after beetroot supplement were estimated using suitable membrane coated CuCP–ZnO–SPCE and validated with the standard Griess method.     

Electrochemical biosensor for the detection of cauliflower mosaic virus 35 S gene sequences using lead sulfide nanoparticles as oligonucleotide labels

Lead sulfide (PbS) nanoparticles were synthesized in aqueous solution and used as oligonucleotide labels for electrochemical detection of the 35 S promoter from cauliflower mosaic virus (CaMV) sequence. The PbS nanoparticles were modified with mercaptoacetic acid and could easily be linked with CaMV 35 S oligonucleotide probe. Target DNA sequences were covalently linked on a mercaptoacetic acid self-assembled gold electrode, and DNA hybridization of target DNA with probe DNA was completed on the electrode surface. PbS nanoparticles anchored on the hybrids were dissolved in the solution by oxidation of HNO₃ and detected using a sensitive differential pulse anodic stripping voltammetric method. The detection results can be used to monitor the hybridization reaction. The CaMV 35 S target sequence was satisfactorily detected with the detection limit as 4.38 × 10⁻¹² mol/L (3σ). The established method extends nanoparticle-labeled electrochemical DNA analysis to specific sequences from genetically modified organisms with higher sensitivity and selectivity.     

Electrochemical DNA biosensor based on silver nanoparticles/poly(3-(3-pyridyl) acrylic acid)/carbon nanotubes modified electrode

In this work, we present an electrochemical DNA sensor based on silver nanoparticles/poly(trans-3-(3-pyridyl) acrylic acid) (PPAA)/multiwalled carbon nanotubes with carboxyl groups (MWCNTs-COOH) modified glassy carbon electrode (GCE). The polymer film was electropolymerized onto MWCNTs-COOH modified electrode by cyclic voltammetry (CV), and then silver nanoparticles were electrodeposited on the surface of PPAA/MWCNTs-COOH composite film. Thiol group end single-stranded DNA (HS-ssDNA) probe was easily covalently linked onto the surface of silver nanoparticles through a 5′ thiol linker. The DNA hybridization events were monitored based on the signal of the intercalated adriamycin by differential pulse voltammetry (DPV). Based on the response of adriamycin, only the complementary oligonucleotides gave an obvious current signal compared with the three-base mismatched and noncomplementary oligonucleotides. Under the optimal conditions, the increase of reduction peak current of adriamycin was linear with the logarithm of the concentration of the complementary oligonucleotides from 9.0 × 10⁻¹² to 9.0 × 10⁻⁹ M with a detection limit of 3.2 × 10⁻¹² M. In addition, this DNA sensor exhibited an excellent reproducibility and stability during DNA hybridization assay.     

Biosensor based on the biocatalysis of microperoxidase-11 in nanocomposite material of multiwalled carbon nanotubes/room temperature ionic liquid for amperometric determination of hydrogen peroxide

A novel nanocomposite material of multiwalled carbon nanotubes (MWCNTs) and room temperature ionic liquid (RTIL) N-butylpyridinium hexafluorophosphate (BPPF₆) was explored and used to construct a novel microperoxidase-11 (MP-11) biosensor for the determination of hydrogen peroxide (H₂O₂). Cyclic voltammetry (CV) and differential pulse voltammetry (DPV) were used to characterize the performance of the biosensor. Under the optimized experimental conditions, H₂O₂ could be detected in a linear calibration range of 0.5 to 7.0 × 10⁻⁷ mol L⁻¹ with a correlation coefficient of 0.9949 (n = 9) and a detection limit of 3.8 × 10⁻⁹ mol L⁻¹ at 3σ. The modified electrodes displayed excellent electrochemical response, high sensitivity, long-term stability, and good bioactivity and selectivity.     

Determination of nanomolar uric and ascorbic acids using enlarged gold nanoparticles modified electrode

Individual and simultaneous determination of 50 nM uric acid (UA) and ascorbic acid (AA) using enlarged, citrate-stabilized gold nanoparticles (AuNPs) self-assembled to 2,5-dimercapto-1,3,4-thiadiazole (DMT) monolayer modified Au (Au/DMT) electrode by an amperometric method is described for the first time. Self-assembly of AuNPs on the electrode surface was confirmed by atomic force microscopy (AFM), attenuated total reflectance FT-IR and diffuse reflectance spectral measurements. The electron transfer reaction (ETR) of [Fe(CN)₆]^3−/4− was blocked at Au/DMT electrode, whereas it was restored with a peak separation of 200 mV after the attachment of AuNPs on the Au/DMT (Au/DMT/AuNPs) electrode, which was confirmed from the ETR of the [Fe(CN)₆]^3−/4− redox couple. When the self-assembled AuNPs were enlarged by hydroxylamine seeding, the ETR of [Fe(CN)₆]^3−/4− was improved significantly with a peak separation of 100 mV. Tapping mode AFM showed that the average size of the enlarged-AuNPs (E-AuNPs) was 50-70 nm. The E-AuNPs modified electrode catalyzes the oxidation of AA and UA, separates their voltammetric signals by 200 mV, and has excellent sensitivity towards AA and UA with a detection limit of 50 nM. The practical application of the modified electrode was demonstrated by measuring the concentration of UA in blood serum and urine.     

Electrochemical spectroscopic investigations on the interaction of an ytterbium complex with DNA and their analytical applications such as biosensor

Metal ion-DNA interactions are important in nature, often changing the genetic material's structure and function. A new Yb complex of YbCl₃ (tris(8-hydroxyquinoline-5-sulfonic acid) ytterbium) was synthesized and utilized as an electrochemical indicator for the detection of DNA oligonucleotide based on its interaction with Yb(QS)₃. Cyclic voltammetry (CV) and fluorescence spectroscopy were used to investigate the interaction of Yb(QS)₃ with ds-DNA. It was revealed that Yb(QS)₃ presented an excellent electrochemical activity on glassy carbon electrode (GCE) and could intercalate into the double helix of double-stranded DNA (ds-DNA). The binding mechanism of interaction was elucidated on glassy carbon electrode dipped in DNA solution and DNA modified carbon paste electrode by using differential pulse voltammetry and cyclic voltammetry. The binding ratio between this complex and ds-DNA was calculated to be 1:1. The extent of hybridization was evaluated on the basis of the difference between signals of Yb(QS)₃ with probe DNA before and after hybridization with complementary DNA. With this approach, this DNA could be quantified over the range from 1 × 10⁻⁸ to 1.1 × 10⁻⁷ M. The interaction mode between Yb(QS)₃ and DNA was found to be mainly intercalative interaction. These results were confirmed with fluorescence experiments.     

Electrochemical assay for deoxyribonuclease I activity

A thiolated oligonucleotide having three ferrocenes was immobilized on a gold electrode through the sulfur-gold linkage. This electrode showed a current response based on the redox reaction of the ferrocene moieties and this response was decreased after treatment with deoxyribonuclease I (DNase I), suggesting the disappearance of the ferrocene moieties on the electrode by the DNase I digestion. A linear correlation between i₀ and i, which are current peaks before and after DNase I treatment, respectively, was observed and this slope was decreased with increase in the amount of DNase I. No current decrease was observed in the presence of EDTA or RNase A instead of DNase I. These results suggested that the current decrease responded specifically to the amount of DNase I and this electrode could be used for an electrochemical DNase I assay. Under the optimum conditions of DNase I digestion at 37 °C for 30 min, a quantitative analysis could be achieved in the range of 10⁻⁴-10⁻² units/μl of DNase I.     

Voltammetric discrimination of mandelic acid enantiomers

We report a novel electrochemical biosensor for direct discrimination of d- and l-mandelic acid (d- and l-MA) in aqueous medium. The glassy carbon electrode (GCE) surface was modified with reduced graphene oxide (rGO) and γ-globulin (GLOB). Electrochemical characterization of the modified electrodes was investigated by cyclic voltammetry and electrochemical impedance spectroscopy. The modified electrode surfaces were also characterized by scanning electron microscopy. Electrochemical response of the prepared electrode (GCE/rGO/GLOB) for discrimination of d- and l-MA enantiomers was investigated by cyclic voltammetry and was compared with bare GCE in the concentration range of 2 to 10 mM. Whereas the bare GCE showed no electrochemical response for the MA enantiomers, the GCE/rGO/GLOB electrode exhibited direct and selective discrimination with different oxidation potential values of 1.47 and 1.71 V and weak reduction peaks at potential values of −1.37 and −1.48 V, respectively. In addition, electrochemical performance of the modified electrode was investigated in mixed solution of d- and l-MA. The results show that the produced electrode can be used as electrochemical chiral biosensor for MA.     

Horseradish peroxidase covalent grafting onto screen-printed carbon electrodes for levetiracetam chronoamperometric determination

A new enzymatic electrochemical biosensor based on disposable transducers, namely screen-printed carbon electrodes, has been developed for the determination of the antiepileptic drug levetiracetam. Horseradish peroxidase was immobilized onto the carbon working electrode previously modified by an aryl diazonium salt. The formation of amide bonds between the amino and carboxylic groups of the enzyme surface, catalyzed by hydroxysuccinimide and carbodiimide, leads to the electrode functionalization. This orientated enzymatic modification results in high reproducibility, with an associated relative standard deviation of 6.21% for the slopes of several calibration curves in the calibration range from 0.10 to 0.83 mM. Experimental variables that can affect levetiracetam chronoamperometric response, such as hydrogen peroxide concentration, pH, and applied potential, were optimized to perform a selective determination. An average limit of detection of 1.75 × 10⁻⁵ M (α = β = 0.05) was obtained. The biosensors were finally applied to the determination of levetiracetam in complex matrices such as pharmaceutical drugs, yielding successful results.     

Electrochemical assay of plasmin activity and its kinetic analysis

A sensitive and convenient electrochemical assay of plasmin activity and its kinetic analysis are described. Thus, a ferrocenyl peptide substrate (FcPS) having a plasmin-specific substrate sequence, Lys-Thr-Phe-Lys, and a Cys residue was prepared and immobilized on a gold electrode through the sulfur-gold linkage. The obtained electrode showed a redox signal based on the ferrocene moiety, suggesting the immobilization of FcPS on the electrode. After treatment of this electrode with plasmin, its electrochemical signal was decreased in proportion to an increase of the amount of plasmin. The detection limit for plasmin in this assay system was as low as 50 ng/ml or 0.15 mU/ml. Real-time monitoring of plasmin reaction on the electrode could also be achieved, and the kinetic parameters of this enzymatic reaction could be determined; for example, the k_cat/K_m value was 0.063 μM⁻¹ s⁻¹. Furthermore, a quantitative assay for streptokinase as a plasminogen activator was also demonstrated by using this system.     

Preparation of a manganese titanate nanosensor: Application in electrochemical studies of captopril in the presence of para-aminobenzoic acid

This study reports the synthesis and characterization of a novel nanostructure-based electrode for electrochemical studies and determination of captopril (CP). At first manganese titanate nanoceramics were synthesized by the sol–gel method. The structural evaluations of the pure nanopowders were investigated by different techniques such as X-ray diffraction (XRD), transmission electron microscopy (TEM), and scanning electron microscopy (SEM). Then it was used to prepare a new nanostructured manganese titanate carbon paste electrode (MnTiO₃/CPE). The characterization of the modified sensor was carried out by comprehensive techniques such as electrochemical impedance spectroscopy (EIS), SEM, and voltammetry. Subsequently, the modified electrode was used for CP catalytic oxidation in the presence of para-aminobenzoic acid (PABA) as a mediator. The results showed that PABA has high catalytic activity for CP oxidation. The electrochemical behavior of CP was studied by cyclic voltammetry (CV), linear sweep voltammetry (LSV), chronoamperometry (CHA), and differential pulse voltammetry (DPV) techniques. Under the optimized conditions, the catalytic oxidation peak current of CP showed two linear dynamic concentration ranges of 1.0 × 10⁻⁸ to 1.0 × 10⁻⁷ and 1.0 × 10⁻⁷ to 1.0 × 10⁻⁶, with a detection limit of 1.6 nM (signal/noise = 3), using the DPV technique. Finally, the proposed method was successfully applied for determination of CP in pharmaceutical and biological samples.     

Peroxynitrite-mediated oxidation of ferrous carbonylated myoglobin is limited by carbon monoxide dissociation

Peroxynitrite-mediated oxidation of ferrous nitrosylated myoglobin (Mb(II)-NO) involves the transient ferric nitrosylated species (Mb(III)-NO), followed by NO dissociation and formation of ferric myoglobin (Mb(III)). In contrast, peroxynitrite-mediated oxidation of ferrous oxygenated myoglobin (Mb(II)-O₂) involves the transient ferrous deoxygenated and ferryl derivatives (Mb(II) and Mb(IV)O, respectively), followed by Mb(III) formation. Here, kinetics of peroxynitrite-mediated oxidation of ferrous carbonylated horse heart myoglobin (Mb(II)-CO) is reported. Values of the first-order rate constant for peroxynitrite-mediated oxidation of Mb(II)-CO (i.e., for Mb(III) formation) and of the first-order rate constant for CO dissociation from Mb(II)-CO (i.e., for Mb(II) formation) are h = (1.2 ± 0.2) × 10⁻² s⁻¹ and k_off(CO) = (1.4 ± 0.2) × 10⁻² s⁻¹, respectively, at pH 7.2 and 20.0 °C. The coincidence of values of h and k_off(CO) indicates that CO dissociation represents the rate limiting step of peroxynitrite-mediated oxidation of Mb(II)-CO.     

Fabrication of chronocoulometric DNA sensor based on gold nanoparticles/poly(l-lysine) modified glassy carbon electrode

In this work, we fabricated a sensitivity chronocoulometric DNA sensor (CDS) based on gold nanoparticles (AuNPs)/poly(l-lysine) complex film modified glassy carbon electrode. Hexaammineruthenium(III) chloride ([Ru(NH₃)₆]³⁺) was used as the electroactive indicator. The assembled process was investigated by cyclic voltammetry (CV) and chronocoulometry (CC). CC is used to monitor the DNA hybridization event by measurement of electrostatic binding [Ru(NH₃)₆]³⁺. Under the optimal conditions, the signal of [Ru(NH₃)₆]³⁺ was linear with the logarithm of the concentration of the complementary oligonucleotides from 1.0 × 10⁻¹³ to 1.0 × 10⁻¹¹ M, and the detection limit is 3.5 × 10⁻¹⁴ M.     

Amperometric sensor based on ferrocene-modified multiwalled carbon nanotube nanocomposites as electron mediator for the determination of glucose

A kind of nanocomposite with good dispersion in water was prepared through covalent adsorption of ferrocenecarboxaldehyde on multiwalled carbon nanotubes (MWNTs) for electrical communication between glucose oxidase (GOD) and electrode. The ferrocene-modified multiwalled carbon nanotube nanocomposites (MWNTs-Fc) could be conveniently cast on electrode surfaces. With the aid of chitosan, GOD was then immobilized on the nanostructure film to form a reagentless amperometric sensor for glucose determination. FTIR spectra and cyclic voltammetry were used to characterize the nanocomposites. The presence of both ferrocene as mediator of electron transfer and MWNTs as conductor enhanced greatly the enzymatic response to the oxidation of glucose. The novel biosensor exhibited a fast response toward glucose with a detection limit of 3.0 × 10⁻⁶ mol/L and the linear range extended up to 3.8 × 10⁻³ mol/L.     

Aerial and underwater carbon metabolism of a Zostera noltii seagrass bed in the Banc d’Arguin, Mauritania

Community respiration and primary production were measured in a dense intertidal Zostera noltii bed on the Banc d’Arguin, Mauritania (West Africa) under aerial and submerged conditions. Metabolism was studied in situ in dark and transparent benthic chambers. CO₂ fluxes in the air were measured over a series of short-term incubations (3 min) using an infrared gas analyzer. Dissolved inorganic carbon fluxes were calculated from concentration changes during one-hour underwater incubations. Air and underwater irradiance levels were measured every minute throughout the experiments. Carbon respiration was lower in the air (2.2 mmol m⁻² h⁻¹) than underwater (5.0 mmol m⁻² h⁻¹); similarly, a production-irradiance model fitted to the data indicated that gross maximal photosynthetic rate was markedly lower during emergence (6.0 mmol C m⁻² h⁻¹) than under water (42.7 mmol C m⁻² h⁻¹). The δ¹³C values observed in shoots indicated a decrease in atmospheric CO₂ contribution, compared to dissolved inorganic carbon, in Z. noltii metabolism along a depth gradient within a single location. As the seagrass bed remains under a thin layer of water at low tide at the studied site, the large difference in primary production can be mainly attributed to photosynthesis inhibition by high pH and oxygen concentration, as well as to the negative feedback of self-shading by seagrass leaves during emersion. The observed differences in respiration can be explained by the oxygen deficit at night during low tide near the sediment surface, a deficit that is consistent with the abundance of anoxia-tolerant species.     

Development of DNA electrochemical biosensor based on immobilization of ssDNA on the surface of nickel oxide nanoparticles modified glassy carbon electrode

A sensitive electrochemical method for DNA hybridization based on immobilization of DNA probe and [Ru(NH₃)₅Cl]PF₆ complex onto nickel oxide nanomaterials (NiOx_np) modified glassy carbon electrode was developed. Due to strong affinity of NiOx_np for phosphate groups, oligonucleotides probe with a terminal 5′-phosphate group was attached to the surface of the modified electrode. DNA immobilization and hybridization were characterized by electrochemical impedance spectroscopy (EIS) and differential pulse voltammetry using K₃Fe(CN)₆/K₄Fe(CN)₆ and [Ru(NH₃)₅Cl]PF₆ as probe and indicator, respectively. The Ru-complex current response indicates only the complementary sequence showing an obvious current signal in comparison to non-complementary and three or single point mismatched sequences. The fabricated biosensor possessed good selectivity and sensitivity for complementary probe, taxon: 32630 tumor necrosis factor (TNF). The linear dynamic range, sensitivity and detection limit of the proposed biosensor were 4 × 10⁻¹⁰ M to 1 × 10⁻⁸ M, 34.32 nA nM⁻¹ and 6.8 × 10⁻¹¹ M, respectively. Excellent reproducibility and stability, quite simple and inexpensive preparation are the other advantages of proposed biosensor.     

Formation of electrochemically reduced graphene oxide on melamine electrografted layers and its application toward the determination of methylxanthines

The current study describes the electrografting of 2,4-diamino-1,3,5-triazine (AT) groups at the surfaces of glassy carbon electrode (GCE) and indium tin oxide (ITO) through in situ diazotization of melamine. The presence of AT groups at the surface of the electrode was confirmed by X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), electrochemical impedance spectroscopy (EIS), and cyclic voltammetry (CV). Furthermore, graphene oxide (GO) was self-assembled on AT grafted GCE. The oxygen functional groups present on the surface of GO were electrochemically reduced to form an electrochemically reduced graphene oxide (ERGO) on AT grafted electrode surface. Raman spectra show the characteristic D and G bands at 1340 and 1605 cm⁻¹, respectively, which confirms the successful attachment of GO on AT grafted surface, and the ratio of D and G bands was increased after the electrochemical reduction of GO. EIS shows that the electron transfer reaction of [Fe(CN)₆]^3−/4− was higher at the ERGO modified electrode than at bare, AT grafted, and GO modified GCEs. The electrocatalytic activity of ERGO was investigated toward the oxidation of methylxanthines. It shows excellent electrocatalytic activity toward these methylxanthines by not only shifting their oxidation potentials toward less positive potentials but also enhancing their oxidation currents.