The atypical lipase B from Candida antarctica is better adapted for organic media than the typical lipase from Thermomyces lanuginosa

Candida antarctica lipase B (CALB) and Thermomyces lanuginosa lipase (TLL) were evaluated as catalysts in different reaction media using hydrolysis of tributyrin as model reaction. In o/w emulsions, the enzymes were used in the free form and for use in monophasic organic media, the lipases were adsorbed on porous polypropylene (Accurel EP-100). In monophasic organic media, the highest specific activity of both lipases was obtained in pure tributyrin at a water activity of >0.5 and at an enzyme loading of 10 mg/g support. With tributyrin emulsified in water, the specific activities were 2780 micromol min(-1) mg(-1) for TLL and 535 micromol min(-1) mg(-1) for CALB. Under optimal conditions in pure tributyrin, CALB expressed 49% of the activity in emulsion (264 micromol min(-1) mg(-1)) while TLL expressed only 9.2% (256 micromol min(-1) mg(-1)) of its activity in emulsion. This large decrease is probably due to the structure of TLL, which is a typical lipase with a large lid domain. Conversion between open and closed conformers of TLL involves large internal movements and catalysis probably requires more protein mobility in TLL than in CALB, which does not have a typical lid region. Furthermore, TLL lost more activity than CALB when the water activity was reduced below 0.5, which could be due to further reduction in protein mobility.     

Covalent immobilization of pure isoenzymes from lipase of Candida rugosa

Covalent immobilization of pure lipases A and B from Candida rugosa on agarose and silica is described. The immobilization increases the half-life of the biocatalysts ( ) with respect to the native pure lipases ( ). The percentage immobilization of lipases A and B is similar in both supports (33–40%). The remaining activity of the biocatalysts immobilized on agarose (70–75%) is greater than that of the enzymatic derivatives immobilized on SiO₂ (40–50%). The surface area and the hydrophobic/hydrophilic properties of the support control the lipase activity of these derivatives. The thermal stability of the immobilized lipase A derivatives is greater than that of lipase B derivatives. The nature of the support influences the thermal deactivation profile of the immobilized derivatives. The immobilization in agarose (hydrophilic support) gives biocatalysts that show a greater initial specific reaction rate than the biocatalysts immobilized in SiO₂ (hydrophobic support) using the hydrolysis of the esters of (R) or (S) 2-chloropropanoic and of (R,S) 2-phenylpropanoic acids as the reaction test. The enzymatic derivatives are active for at least 196 h under hydrolysis conditions. The stereospecificity of the native and the immobilized enzymes is the same.     

Efficient immobilization of lipases by entrapment in hydrophobic sol-gel materials

The commercial application of lipases as biocatalysts for organic synthesis requires simple but efficient methods to immobilize the enzyme, yielding highly stable and active biocatalysts which are easy to recover. In this study, we present a novel method to achieve lipase immobilization by entrapment in chemically inert hydrophobic silica gels which are prepared by hydrolysis of alkyl-substituted silanes in the presence of the enzyme. A typical immobilization procedure uses: an aqueous solution of lipase; sodium fluoride as a catalyst; and additives like polyvinyl alcohol or proteins and alkoxysilane derivatives like RSi-(OMe)(3) with R = alkyl, aryl, or alkoxy as gel precursors. The effect of various immobilization parameters like stoichiometric ratio of water, silane, type and amount of additive, type and amount of catalyst, and type of silane has been carefully studied. The new method is applicable for a wide variety of lipases, yielding immobilized lipases with esterification activities enhanced by a factor of up to 88, compared to the commercial enzyme powders under identical conditions. Studies on the stability of sol-gel immobilized lipases under reaction conditions or storage (dry, in aqueous or organic medium) revealed an excellent retention of enzymatic activity. The possible reasons for the increased enzyme activities are discussed. (c) 1996 John Wiley & Sons, Inc.     

A comparative study on two fungal lipases from Thermomyces lanuginosus and Yarrowia lipolytica shows the combined effects of detergents and pH on lipase adsorption and activity

The effects of various detergents and pH on the interfacial binding and activity of two fungal lipases from Yarrowia lipolytica (YLLIP2) and Thermomyces lanuginosus (TLL) were investigated using trioctanoin emulsions as well as monomolecular films spread at the air-water interface. Contrary to TLL, YLLIP2 was found to be more sensitive than TLL to interfacial denaturation but it was protected by detergent monomers and lowering the temperature. At pH 7.0, both the interfacial binding and the activities on trioctanoin of YLLIP2 and TLL were inhibited by sodium taurodeoxycholate (NaTDC). At pH 6.0, however, YLLIP2 remained active on trioctanoin in the presence of NaTDC, whereas TLL did not. YLLIP2 activity on trioctanoin was associated with strong interfacial binding of the enzyme to trioctanoin emulsion, whereas TLL was mostly detected in the water phase. The combined effects of bile salts and pH on lipase activity were therefore enzyme-dependent. YLLIP2 binds more strongly than TLL at oil-water interfaces at low pH when detergents are present. These findings are particularly important for lipase applications, in particular for enzyme replacement therapy in patients with pancreatic enzyme insufficiency since high detergent concentrations and highly variable pH values can be encountered in the GI tract.     

Immobilization of lipases for non-aqueous synthesis

Immobilization of lipases involves many levels of complications relating to the structure of the active site and its interactions with the immobilization support. Interaction of the so called hydrophobic ‘lid’ with the support has been reported to affect synthetic activity of an immobilized lipase. In this work we evaluate and compare the synthetic activity of lipases from different sources immobilized on different kinds of supports with varying hydrophobicity. Humicola lanuginosa lipase, Candida antarctica lipase B and Rhizomucor miehei lipase were physically adsorbed onto two types of hydrophobic carriers, namely hydrophilic carriers with conjugated hydrophobic ligands, and supports with base matrix hydrophobicity. The prepared immobilized enzymes were used for acylation of n-butanol with oleic acid as acyl donor in iso-octane with variable water content (0–2.8%, v/v) as reaction medium. Enzyme activity and effect of water on the activity of the immobilized derivatives were compared with those of respective soluble lipases and a commercial immobilized lipase Novozyme 435. Both R. miehei and H. lanuginosa immobilized lipases showed maximum activity at 1.39% (v/v) added water concentration. Sepabeads, a methacrylate based hydrophilic support with conjugated octadecyl chain showed highest immobilized esterification (synthetic) activity for all three enzymes, and of the three R. miehei lipase displayed maximum esterification activity comparable to the commercial enzyme.     

An ultraviolet spectrophotometric assay for the screening of sn-2-specific lipases using 1,3-O-dioleoyl-2-O-α-eleostearoyl-sn-glycerol as substrate

In the present study, we propose a continuous assay for the screening of sn-2 lipases by using triacylglycerols (TAGs) from Aleurites fordii seed (tung oil) and a synthetic TAG containing the α-eleostearic acid at the sn-2 position and the oleic acid (OA) at the sn-1 and sn-3 positions [1,3-O-dioleoyl-2-O-α-eleostearoyl-sn-glycerol (sn-OEO)]. Each TAG was coated into a microplate well, and the lipase activity was measured by optical density increase at 272 nm due to transition of α-eleostearic acid from the adsorbed to the soluble state. The sn-1,3-regioselective lipases human pancreatic lipase (HPL), LIP2 lipase from Yarrowia lipolytica (YLLIP2), and a known sn-2 lipase, Candida antarctica lipase A (CALA) were used to validate this method. TLC analysis of lipolysis products showed that the lipases tested were able to hydrolyze the sn-OEO and the tung oil TAGs, but only CALA hydrolyzed the sn-2 position. The ratio of initial velocities on sn-OEO and tung oil TAGs was used to estimate the sn-2 preference of lipases. CALA was the enzyme with the highest ratio (0.22 ± 0.015), whereas HPL and YLLIP2 showed much lower ratios (0.072 ± 0.026 and 0.038 ± 0.016, respectively). This continuous sn-2 lipase assay is compatible with a high sample throughput and thus can be applied to the screening of sn-2 lipases.     

The lid is a structural and functional determinant of lipase activity and selectivity

In several lipases access to the enzyme active site is regulated by the position of a mobile structure named the lid. The role of this region in modulating lipase function is reviewed in this paper analysing the results obtained with three different recombinant lipases modified in the lid sequence: Candida rugosa lipase isoform 1 (CRL1), Pseudomonas fragi lipase (PFL) and Bacillus subtilis lipase A (BSLA). A CRL chimera enzyme obtained by replacing its lid with that of another C. rugosa lipase isoform (CRL1LID3) was found to be affected in both activity and enantioselectivity in organic solvent. Variants of the PFL protein in which three polar lid residues were replaced with amino acids strictly conserved in homologous lipases displayed altered chain length preference profile and increased thermostability. On the other hand, insertion of lid structures from structurally homologous enzymes into BSLA, a lipase that naturally does not possess such a lid structure, caused a reduction in the enzyme activity and an altered substrate specificity. These results strongly support the concept that the lid plays an important role in modulating not only activity but also specifity, enantioselectivity and stability of lipase enzymes.     

Screening and catalytic activity in organic synthesis of novel fungal and yeast lipases

A total of 969 microbial strains were isolated from soil samples and tested to determine their lipolytic activity by employing screening techniques on solid and in liquid media. Ten lipase-producing microorganisms were selected and their taxonomic identification was carried out. From these strains Achremonium murorum, Monascus mucoroides, Arthroderma ciferri, Fusarium poae, Ovadendron sulphureo-ochraceum and Rhodotorula araucariae are described as lipase-producers for the first time. Hydrolysis activity of the crude lipases against both tributyrin and olive oil was measured. Heptyl oleate synthesis was carried out to test the activity of the selected lipases as biocatalysts in organic medium. All the selected lipases were tested as biocatalysts in several organic reactions using unnatural substrates. Lipases from the fungi Fusarium. oxysporum and O. sulphureo-ochraceum gave the best yields and enantioselectivities in the esterification of carboxylic acids. F. oxysporum and Penicillium chrysogenum lipases were the most active ones for the acylation of alcohols without steric hindrance. A. murorum lipase is very useful for the esterification of menthol. F. oxysporum and Fusarium. solani lipases were very stereoselective in the synthesis of carbamates.     

Sol–gels and cross-linked aggregates of lipase PS from Burkholderia cepacia and their application in dry organic solvents

Lipase PS from Burkholderia cepacia (formerly Pseudomonas cepacia) was successfully immobilized in sol–gels under low methanol conditions using lyophilization in order to dry the gel. The enzyme was also cross-linked with glutaraldehyde to CLEAs without any additives. These immobilized enzyme preparations were employed for the highly enantioselective acylations of 1-phenylethanol (1), 1-(2-furyl)ethanol (2) and N-acylated 1-amino-2-phenylethanol (3) with vinyl acetate in organic solvents. Enzymatic hydrolysis of the obtained ester product was observed as a side reaction of the acylation of 3 in the presence of lipase PS powder. Hydrolysis was suppressed when the immobilized preparations of lipase PS were used.     

Enhancement of activity and selectivity of Candida rugosa lipase and Candida antarctica lipase A by bioimprinting and/or immobilization for application in the selective ethanolysis of fish oil

Candida rugosa lipase (CRL) and Candida antarctica lipase A (CALA) with improved activity and selectivity were prepared for use in organic solvent media. CRL bioimprinted with fatty acids exhibited eightfold enhanced transesterification activity in hexane. Combination of bioimprinting and coating with lecithin or with immobilization did not improve the activity further. CALA was immobilized with and without bioimprinting, none of which improved the activity. All modified lipases were tested for selective ethanolysis of fish oil to concentrate omega-3 polyunsaturated fatty acids (PUFA). None of the preparations, except the immobilized ones catalysed ethanolysis. Immobilized CRL-catalyzed ethanolysis giving 27% (v/v) ethyl esters (EE) in 48 h, of which 43 mol% was oleic acid but no PUFA was detected in the EE fraction. Fatty acid selectivity of CALA was significantly improved by immobilization combined with bioimprinting, resulting in 5.5-fold lower omega-3 PUFA in EE.     

Lipase-catalysed synthesis of ester oils from biodiesel by-products

Ester oils obtained from natural long-chain fatty acids and alcohols are versatile substitutes for many petroleum-based products. Their efficient synthesis with the solvent-free esterification of free fatty acids (FFA) from by-products of biodiesel fabrication and 2-ethyl-1-hexanol with immobilised lipase from Thermomyces lanuginosa was investigated. The immobilisation of the biocatalyst in static emulsion yielded a specific esterification activity that was higher by a factor of 4.9-9.4 than the activity of the native enzyme. Favourable properties of the silicone-based immobilisation matrix in terms of stability and immobilisation yield were observed. In biodiesel by-products, the immobilised lipase catalysed the esterification of FFA as well as the transesterification of residual fatty acid methyl esters (FAME) to the desired ester oils. A conversion of 90% FFA and 35% FAME gave a total yield of 60%. The inactivation coefficients during repeated use in a stirred-tank reactor with intermittent pressure reduction were exceptionally low.     

A New Spectrophotometric Method for the Detection of Lipase Activity Using 2,4-Dinitrophenyl Butyrate as a Substrate

A rapid and sensitive assay for the detection of lipase activity is described. The method is based upon the increase in absorbance at 360 nm due to the formation of the 2,4-dinitrophenolate anion during the enzymatic hydrolysis of 2,4-dinitrophenyl butyrate. The substrate is used in an emulsified form. Using a diode array spectrophotometer with internal referencing a correction can be made for absorbance changes due to clearance of the emulsion during hydrolysis. The small reaction volume and the high extinction coefficient of the product makes the method applicable for detection of both low substrate and low enzyme concentration.

Four lipases were tested: lipase from porcine pancreas, Candida cylindracea, Pseudomonas sp. and Aspergillus niger. All enzymes are readily able to catalyse the hydrolysis of 2,4-dinitrophenyl butyrate.     

Carica papaya by-products as new biocatalysts for the synthesis of oleic acid esters

Carica papaya lipase is a versatile biocatalyst that is employed for many biotechnological purposes. Its lipase activity was first observed to be tightly linked to the insoluble fraction of latex. Nevertheless, recent studies have shown that this activity is also present in the fruit peel and seeds, suggesting that the lipase activity occurs in other parts of the plant. In the present work, the hydrolytic activity on trioctanoin was determined in various plant by-products, including latex, leafs, petioles, meristems, fruits, and the stem. The most hydrolytic activity was found in the latex (11 U/mL), followed by the petioles (1.7 U/mL). The hydrolytic selectivity was determined using triacetin, tripropionin, tributyrin, and trioctanoin. The enzymes present in the latex showed a higher rate of hydrolysis of tributyrin, while those present in the petioles had a preference for tripropionin, possibly indicating the occurrence of at least two different triacylglycerol hydrolases. Five self-immobilized biocatalysts were obtained: lyophilized latex (LL), lyophilized petioles (LP), bagasse from petioles (BP), and, after a simple cold water washing treatment, treated lyophilized latex (TLL), and treated lyophilized petioles (TLP). This procedure yielded a 5- and 10-fold increase in the latex and petiole activity, respectively, on tributyrin. The selected biocatalysts, TLL and BP, were tested for the synthesis of oleic acid esters (OAE), reaching conversions over 80%. Unexpectedly, only BP preferentially synthesized dodecyl oleate (DO) and showed the highest thermostability. Therefore, BP was further assayed for DO synthesis in a packed bed reactor (PBR), achieving 96% conversion over 40 h. This study shows the great potential of C. papaya by-products, particularly BP, as biocatalysts for the synthesis of OAE.     

Characterization of sol–gel encapsulated lipase using tetraethoxysilane as precursor

Lipase from Candida rugosa was encapsulated within a chemically inert sol–gel support prepared by polycondensation of the precursor tetraethoxysilane (TEOS) in the presence of polyethylene glycol (PEG) as additive. The properties of silica and their derivatives with regard to mean pore diameter, specific surface area, mean pore size, weight loss upon heating (thermogravimetric analysis, TGA) and ²⁹Si and ¹³C NMR are reported. The pH optimum shifted from 7.8 to 6.7 and optimum temperature jumped from 36 to 60 °C upon enzyme encapsulation. Encapsulated lipase in presence of PEG (EN-PEG) exhibited higher stability in the range of 37–45 °C, but from 50 to 65 °C the EN-PEG was inactivated after seven cycles. Hydrolytic activity during long-term storage at room temperature decreased to 50% after 94 days. High diffusional resistance was observed for large oil concentration reducing hydrolytic effectiveness by 60% in the case of the encapsulated lipase. NMR, pore size and specific surface area data suggested an active participation of the lipase enzyme during gelling of the silica matrix. This lead to reduction of available Si–OH groups, larger pores and smaller surface area. Larger pores increase substrate diffusion that correlates well with higher hydrolytic activity of the TEOS–PEG sol–gel matrix encapsulated enzyme in comparison with other sol–gel supports.     

Influence of ionic liquids as additives on sol–gel immobilized lipase

The immobilization of lipase from Candida rugosa, using ionic liquids as additives to protect the inactivation of lipase by released alcohol and shrinking of gel during sol–gel process, was investigated. The influence of various factors, such as structure of ionic liquids, content of ionic liquids and types of precursor in the sol–gel process on the activity and stability of immobilized lipase was also studied. The highest hydrolytic activity of immobilized lipase was obtained when the hydrophilic ionic liquid, [C₂mim][BF₄], was used as an additive, while the highest stability of immobilized lipase was obtained by using hydrophobic ionic liquid, [C₁₆mim][Tf₂N]. Therefore, the binary mixtures of these ionic liquids as additives were used to obtain the optimal immobilized lipase, which shows both high activity and stability. The hydrolysis and esterification activities of lipase co-immobilized with the mixture of 1:1 at molar ratio of [C₂mim][BF₄] and [C₁₆mim][Tf₂N] were 10-fold and 14-fold greater than in silica gel without ionic liquids (ILs), respectively. After 5 days incubation of this immobilized lipase in n-hexane at 50 °C, 84% of initial activity was remained, while the residual activity of the lipase immobilized without ILs was 28%.     

Enhanced reactivity of Rhizopus oryzae lipase displayed on yeast cell surfaces in organic solvents: potential as a whole-cell biocatalyst in organic solvents

Immobilization of enzymes on some solid supports has been used to stabilize enzymes in organic solvents. In this study, we evaluated applications of genetically immobilized Rhizopus oryzae lipase displayed on the cell surface of Saccharomyces cerevisiae in organic solvents and measured the catalytic activity of the displayed enzyme as a fusion protein with alpha-agglutinin. Compared to the activity of a commercial preparation of this lipase, the activity of the new preparation was 4.4 x 10(4)-fold higher in a hydrolysis reaction using p-nitrophenyl palmitate and 3.8 x 10(4)-fold higher in an esterification reaction with palmitic acid and n-pentanol (0.2% H2O). Increased enzyme activity may occur because the lipase displayed on the yeast cell surface is stabilized by the cell wall. We used a combination of error-prone PCR and cell surface display to increase lipase activity. Of 7,000 colonies in a library of mutated lipases, 13 formed a clear halo on plates containing 0.2% methyl palmitate. In organic solvents, the catalytic activity of 5/13 mutants was three- to sixfold higher than that of the original construct. Thus, yeast cells displaying the lipase can be used in organic solvents, and the lipase activity may be increased by a combination of protein engineering and display techniques. Thus, this immobilized lipase, which is more easily prepared and has higher activity than commercially available free and immobilized lipases, may be a practical alternative for the production of esters derived from fatty acids.     

Supplementation of watermelon peels as an enhancer of lipase and esterase production by Yarrowia lipolytica in solid-state fermentation and their potential use as biocatalysts in poly(ethylene terephthalate) (PET) depolymerization reactions

Abstract

Yarrowia lipolytica is a yeast that presents high biotechnological potential due to its ability to produce many metabolites, among them lipases and esterases, which are important industrial biocatalysts. Since Brazil is an agroindustrial country, it generates an enormous diversity of residues or byproducts that can be used as a platform for biomolecules production. This work aims to evaluate lipase and esterase production by Y. lipolytica via solid-state fermentation using soybean bran and soybean bran supplemented with watermelon peels in different contents, and subsequent use of the enzyme extracts for poly(ethylene terephthalate) (PET) hydrolysis. Supplementation of watermelon peels in the lowest content led to an improvement of lipase activity in almost 31%, reaching 75.22?U g^?1. Esterase productivity was 1.5-fold higher when 20?wt% of watermelon peels were added to the media culture. Timecourse evaluation of enzymes production showed a maximum lipase activity in 14?h and similar esterase activity in 14 and 20?h of fermentation. Proteases production were also intensified in supplemented samples. Enzymes produced with 5?wt% watermelon peels supplementation led to higher terephthalic acid concentration (up to 42.02?µmol L^?1) during PET depolymerization. Results suggest a great potential of enzyme production in low cost fermentative media to act as biocatalysts in PET hydrolysis reactions.     

Lipase-catalysed synthesis of ester oils from biodiesel by-products

Ester oils obtained from natural long-chain fatty acids and alcohols are versatile substitutes for many petroleum-based products. Their efficient synthesis with the solvent-free esterification of free fatty acids (FFA) from by-products of biodiesel fabrication and 2-ethyl-1-hexanol with immobilised lipase from Thermomyces lanuginosa was investigated. The immobilisation of the biocatalyst in static emulsion yielded a specific esterification activity that was higher by a factor of 4.9–9.4 than the activity of the native enzyme. Favourable properties of the silicone-based immobilisation matrix in terms of stability and immobilisation yield were observed. In biodiesel by-products, the immobilised lipase catalysed the esterification of FFA as well as the transesterification of residual fatty acid methyl esters (FAME) to the desired ester oils. A conversion of 90% FFA and 35% FAME gave a total yield of 60%. The inactivation coefficients during repeated use in a stirred-tank reactor with intermittent pressure reduction were exceptionally low.     

Isolation and characterization of an extracellular lipase from Mucor sp strain isolated from palm fruit

During our screening of lipolytic fungus which may play a role in the acidification of palm oil, we have recently isolated a Mucor sp strain. Culture conditions were optimized and the highest lipase production amounting to 57 U/ml was achieved after 6 days of cultivation. The extracellular lipase was purified 1050-fold by ammonium sulfate precipitation, carboxymethyl–sephadex chromatography and Sephadex G75 gel filtration to a final specific activity of 6600 IU/mg. The molecular weight of the homogenous lipase was determined about 42 kDa by gel filtration and SDS–polyacrylamide gel electrophoresis. The purified lipase was determined as a glycoprotein with a pI of 6.2. The Nt sequence was determined as AspGluIleGluThrValGlyXPheThrMetAspLeuProProAsnProPro and showed no homology with the sequences of the known lipases suggesting that the enzyme may be a new lipase. The purified lipase hydrolyzed both synthetic and natural triglycerides with the optimal activity recorded on trioctanoin and sunflower oil, respectively. Its activity was strongly inhibited by Triton X-100 and SDS. Metal ions such as Fe³⁺, Fe²⁺ and Hg²⁺ also decreased the lipase activity.     

Geotrichum candidum 4013: Extracellular lipase versus cell-bound lipase from the single strain

Two types of lipases (extracellular and cell-bound) were produced by Geotrichum candidum 4013 in liquid medium and were used as biocatalysts in blackcurrant oil hydrolysis. Reaction products were analysed for the degree of conversion from which enzyme activity was evaluated, and the composition of free fatty acids was compared to the composition of oil substrate. The enzyme activity was measured also before and after the reaction in SC-CO₂. The fatty acid composition of the acids liberated from oil by hydrolysis suggests a specificity of the cell-bound and extracellular enzymes from Geotrichum candidum 4013. The extracellular lipase displays low selectivity to the polyunsaturated fatty acids, and the cell-bound lipase possesses selectivity to the saturated fatty acids. Enantioselectivity of the tested processes achieved with both induced enzymes was high (from 43 to 242). The activity of all enzymes has markedly increased after their exposure to SC-CO₂. The treatment of enzymes by SC-CO₂ could be easy-to-use approaches to improve the efficiency of enzymatic reactions.