Boosting Polysulfide Redox Kinetics by Graphene‐Supported Ni Nanoparticles with Carbon Coating

Lithium–sulfur batteries have attracted extensive attention because of their high energy density. However, their application is still impeded by the inherent sluggish kinetics and solubility of intermediate products (i.e., polysulfides) of the sulfur cathode. Herein, graphene‐supported Ni nanoparticles with a carbon coating are fabricated by directly carbonizing a metal–organic framework/graphene oxide composite, which is then dispersed on a commercial glass fiber membrane to form a separator with electrocatalytic activity. In situ analysis and electrochemical investigation demonstrate that this modified separator can effectively suppress the shuttle effect and regulate the catalytic conversion of intercepted polysulfides, which is also confirmed by density functional theory calculations. It is found that Ni–C sites can chemically interact with polysulfides and stabilize the radical S₃^?? through Ni? S bonds to enable fast dynamic equilibrium with S₆^2?, while Ni nanoparticles reduce the oxidation barrier of Li₂S and accelerate ion/electron transport. As a result, the corresponding lithium–sulfur battery shows a high cycle stability (88% capacity retention over 100 cycles) even with a high sulfur mass loading of 8 mg cm^?2 and lean electrolyte (6.25 µ L mg^?1). Surprisingly, benefitting from the improved kinetics, the battery can work well at ?50 °C, which is rarely achieved by conventional Li–S batteries.     

Tethered Molecular Sorbents: Enabling Metal‐Sulfur Battery Cathodes

A rechargeable battery that uses sulfur at the cathode and a metal (e.g., Li, Na, Mg, or Al) at the anode provides perhaps the most promising path to a solid‐state, rechargeable electrochemical storage device capable of high charge storage capacity. It is understood that solubilization in the electrolyte and loss of sulfur in the form of long‐chain lithium polysulfides (Li₂S_x, 2 < x < 8) has hindered development of the most studied of these devices, the rechargeable Li‐S battery. Beginning with density‐functional calculations of the structure and interactions of a generic lithium polysulfide species with nitrile containing molecules, it is shown that it is possible to design nitrile‐rich molecular sorbents that anchor to other components in a sulfur cathode and which exert high‐enough binding affinity to Li₂S_x to limit its loss to the electrolyte. It is found that sorbents based on amines and imidazolium chloride present barriers to dissolution of long‐chain Li₂S_x and that introduction of as little as 2 wt% of these molecules to a physical sulfur‐carbon blend leads to Li‐S battery cathodes that exhibit stable long‐term cycling behaviors at high and low charge/discharge rates.     

Tailored Reaction Route by Micropore Confinement for Li–S Batteries Operating under Lean Electrolyte Conditions

Lithium‐sulfur (Li–S) batteries are one of the most promising alternative energy storage systems beyond Li‐ion batteries. However, the sluggish kinetics of the nucleation and growth of the solid discharge product of Li₂S/Li₂S₂ in the lower discharge plateau has been recently identified as a critical hurdle for attaining high specific capacity in Li–S batteries with high sulfur loadings under lean electrolyte conditions. Herein, a new strategy of breaking the charge‐transport bottleneck by successful generation of experimentally verified stable Li₂S₂ and a reservoir of quasi‐solid lithium polysulfides within the micropores of activated carbon fiber cloth as a high‐sulfur‐loading host is proposed. The developed Li–S cell is capable of delivering a highly sustainable areal capacity of 6.0 mAh cm^?2 under lower electrolyte to sulfur ratios (<3.0 mL_E g_S^?1). Micropore confinement leads to generation of solid Li₂S₂ that enables high utilization of the entire electroactive area by its inherent self‐healing capacity. This strategy opens a new avenue for rational material designs for Li–S batteries under lean electrolyte condition.     

High‐Performance Lithium‐Sulfur Batteries with a Self‐Supported, 3D Li2S‐Doped Graphene Aerogel Cathodes

Lithium‐sulfur (Li‐S) batteries are being considered as the next‐generation high‐energy‐storage system due to their high theoretical energy density. However, the use of a lithium‐metal anode poses serious safety concerns due to lithium dendrite formation, which causes short‐circuiting, and possible explosions of the cell. One feasible way to address this issue is to pair a fully lithiated lithium sulfide (Li₂S) cathode with lithium metal‐free anodes. However, bulk Li₂S particles face the challenges of having a large activation barrier during the initial charge, low active‐material utilization, poor electrical conductivity, and fast capacity fade, preventing their practical utility. Here, the development of a self‐supported, high capacity, long‐life cathode material is presented for Li‐S batteries by coating Li₂S onto doped graphene aerogels via a simple liquid infiltration–evaporation coating method. The resultant cathodes are able to lower the initial charge voltage barrier and attain a high specific capacity, good rate capability, and excellent cycling stability. The improved performance can be attributed to the (i) cross‐linked, porous graphene network enabling fast electron/ion transfer, (ii) coated Li₂S on graphene with high utilization and a reduced energy barrier, and (iii) doped heteroatoms with a strong binding affinity toward Li₂S/lithium polysulfides with reduced polysulfide dissolution based on first‐principles calculations.     

A Lithium–Sulfur Cell Based on Reversible Lithium Deposition from a Li2S Cathode Host onto a Hostless‐Anode Substrate

The development of lithium–sulfur batteries necessitates a thorough understanding of the lithium‐deposition process. A novel full‐cell configuration comprising an Li₂S cathode and a bare copper foil on the anode side is presented here. The absence of excess lithium allows for the realization of a truly lithium‐limited Li–S battery, which operates by reversible plating and stripping of lithium on the hostless‐anode substrate (copper foil). Its performance is closely tied to the efficiency of lithium deposition, generating valuable insights on the role and dynamic behavior of lithium anode. The Li₂S full cell shows reasonable capacity retention with a Coulombic efficiency of 96% over 100 cycles, which is a tremendous improvement over that of a similar lithium‐plating‐based full cell with LiFePO₄ cathodes. The exceptional robustness of the Li₂S system is attributed to an intrinsic stabilization of the lithium‐deposition process, which is mediated by polysulfide intermediates that form protective Li₂S and Li₂S₂ regions on the deposited lithium. Combined with the large improvements in energy density and safety by the elimination of a metallic lithium anode, the stability and electrochemical performance of the lithium‐plating‐based Li₂S full cell establish it as an important trajectory for Li–S battery research, focusing on practical realization of reversible lithium anodes.     

Polysulfide Confinement and Highly Efficient Conversion on Hierarchical Mesoporous Carbon Nanosheets for Li–S Batteries

Lithium–sulfur (Li–S) batteries have attracted increasing attention due to their extremely high theoretical specific capacity and a promising power density. However, practical applications of Li–S batteries are still limited by the relatively low performance, owing to poor conductivity of sulfur itself and discharge products (Li₂S/Li₂S₂) as well as the shuttle effect of the intermediate polysulfide. Herein, honeycomb‐like mesoporous Co, N‐doped carbon nanosheets (MC‐NS) with a high specific surface area and abundant defects are developed which, simultaneously enable polysulfide confinement and highly efficient conversion. Moreover, density functional theory calculations and experiments show that the Co‐N‐C catalytic site as well as defects on the carbon skeleton of the MC‐NS facilitate high efficiency in suppressing the shuttle effect of polysulfides. In situ Raman spectra further demonstrate the enhancement of adsorption ability and conversion efficiency of polysulfides on this host. As a result, the MC‐NS enables much increased specific capacity and cycling stability of Li–S batteries. This work provides a useful strategy for realizing practical applications of high‐performance Li–S batteries.     

Highly Solvating Electrolytes for Lithium–Sulfur Batteries

There is a critical need to evaluate lithium–sulfur (Li–S) batteries with practically relevant high sulfur loadings and minimal electrolyte. Under such conditions, the concentration of soluble polysulfide intermediates in the electrolyte drastically increases, which can alter the fundamental nature of the solution‐mediated discharge and thereby the total sulfur utilization. In this work, an investigation into various high donor number (DN) electrolytes that allow for increased polysulfide dissolution is presented, and the way in which this property may in fact be necessary for increasing sulfur utilization at low electrolyte and high loading conditions is demonstrated. The solvents dimethylacetamide, dimethyl sulfoxide, and 1‐methylimidazole are holistically evaluated against dimethoxyethane as electrolyte co‐solvents in Li–S cells, and they are used to investigate chemical and electrochemical properties of polysulfide species at both dilute and practically relevant conditions. The nature of speciation exhibited by lithium polysulfides is found to vary significantly between these concentrations, particularly with regard to the S₃^?? species. Furthermore, the extent of the instability in conventional electrolyte solvents and high DN solvents with both lithium metal and polysulfides is thoroughly investigated. These studies establish a basis for future efforts into rationally designing an optimal electrolyte for a lean electrolyte, high energy density Li–S battery.     

Conductive and Catalytic Triple‐Phase Interfaces Enabling Uniform Nucleation in High‐Rate Lithium–Sulfur Batteries

Rechargeable lithium–sulfur batteries have attracted tremendous scientific attention owing to their superior energy density. However, the sulfur electrochemistry involves multielectron redox reactions and complicated phase transformations, while the final morphology of solid‐phase Li₂S precipitates largely dominate the battery's performance. Herein, a triple‐phase interface among electrolyte/CoSe₂/G is proposed to afford strong chemisorption, high electrical conductivity, and superb electrocatalysis of polysulfide redox reactions in a working lithium–sulfur battery. The triple‐phase interface effectively enhances the kinetic behaviors of soluble lithium polysulfides and regulates the uniform nucleation and controllable growth of solid Li₂S precipitates at large current density. Therefore, the cell with the CoSe₂/G functional separator delivers an ultrahigh rate cycle at 6.0 C with an initial capacity of 916 mAh g^?1 and a capacity retention of 459 mAh g^?1 after 500 cycles, and a stable operation of high sulfur loading electrode (2.69–4.35 mg cm^?2). This work opens up a new insight into the energy chemistry at interfaces to rationally regulate the electrochemical redox reactions, and also inspires the exploration of related energy storage and conversion systems based on multielectron redox reactions.     

MoN Supported on Graphene as a Bifunctional Interlayer for Advanced Li‐S Batteries

Rational design of effective polysulfide barriers is highly important for high‐performance lithium‐sulfur (Li‐S) batteries. A variety of adsorbents have been applied as interlayers to alleviate the shuttle effect. Nevertheless, the unsuccessful oxidation of Li₂S on interlayers leads to loss of active materials and blocks Li ion transport. In this work, a MoN‐based interlayer sandwiched between the C‐S cathode and the separator is developed. Such an interlayer not only strongly binds lithium polysulfides via Mo‐S bonding but also efficiently accelerates the decomposition of Li₂S. The acceleration mechanism toward Li₂S decomposition is determined to be a combination of contributions of catalytic cleavage of Li‐S bond in Li₂S based on the proposed covalence‐activation mechanism and rapid migration of the produced Li ions. As a result, the C–S cathodes with the as‐developed interlayer manifest a negligible charging potential barrier and outstanding cycling stability with a very low capacity fading rate of 0.023% per cycle during 1500 cycles at 1 C. High areal capacity of 6.02 mAh cm^?2 is achieved for high sulfur loading of 7.0 mg cm^?2 after cycling at 0.1 C. The material and strategy demonstrated in this work can open the door toward developing shuttle suppression interlayers without impairing cathode performance.     

Carbon Quantum Dots–Modified Interfacial Interactions and Ion Conductivity for Enhanced High Current Density Performance in Lithium–Sulfur Batteries

Significant progress has achieved for developing lithium–sulfur (Li–S) batteries with high specific capacities and excellent cyclic stability. However, some critical issues emerge when attempts are made to raise the areal sulfur loading and increase the operation current density to meet the standards for various industrial applications. In this work, polyethylenimine‐functionalized carbon dots (PEI‐CDots) are designed and prepared for enhancing performance of the Li–S batteries with high sulfur loadings and operation under high current density situations. Strong chemical binding effects towards polysulfides and fast ion transport property are achieved in the PEI‐CDots‐modified cathodes. At a high current density of 8 mA cm^?2, the PEI‐CDots‐modified Li–S battery delivers a reversible areal capacity of 3.3 mAh cm^?2 with only 0.07% capacity decay per cycle over 400 cycles at 6.6 mg sulfur loading. Detailed analysis, involving electrochemical impedance spectroscopy, cyclic voltammetry, and density functional theory calculations, is done for the elucidation of the underlying enhancement mechanism by the PEI‐CDots. The strongly localized sulfur species and the promoted Li⁺ ion conductivity at the cathode–electrolyte interface are revealed to enable high‐performance Li–S batteries with high sulfur loading and large operational current.     

High‐Performance All‐Solid‐State Lithium–Sulfur Batteries Enabled by Amorphous Sulfur‐Coated Reduced Graphene Oxide Cathodes

Safety and the polysulfide shuttle reaction are two major challenges for liquid electrolyte lithium–sulfur (Li–S) batteries. Although use of solid‐state electrolytes can overcome these two challenges, it also brings new challenges by increasing the interface resistance and stress/strain. In this work, the interface resistance and stress/strain of sulfur cathodes are significantly reduced by conformal coating ≈2 nm sulfur (S) onto reduced graphene oxide (rGO). An Li–S full cell consisting of an rGO@S‐Li₁₀GeP₂S₁₂‐acetylene black (AB) composite cathode is evaluated. At 60 °C, the all‐solid‐state Li–S cell demonstrates a similar electrochemical performance as in liquid organic electrolyte, with high rate capacities of 1525.6, 1384.5, 1336.3, 903.2, 502.6, and 204.7 mA h g^?1 at 0.05, 0.1, 0.5, 1.0, 2.0, and 5.0 C, respectively. It can maintain a high and reversible capacity of 830 mA h g^?1 at 1.0 C for 750 cycles. The uniform distribution of the rGO@S nanocomposite in the Li₁₀GeP₂S₁₂‐AB matrix generates uniform volume changes during lithiation/delithiation, significantly reducing the stress/strain, thus extending the cycle life. Minimization of the stress/strain of solid cells is the key for a long cycle life of all‐solid‐state Li–S batteries.     

Tungsten Disulfide Catalysts Supported on a Carbon Cloth Interlayer for High Performance Li–S Battery

The capacity limitations of insertion‐compound cathodes has motivated interest in a sulfur cathode for a rechargeable battery cell with a metallic‐lithium anode; but irreversible capacity loss owing to solubility of intermediate Li₂S_x (x = 2–8) polysulfides in the organic‐liquid electrolytes used has prevented practical application. A dual‐function cathode structure consisting of layered tungsten disulfide (WS₂) supported both on the cathode current collector and on a carbon cloth interlayer (CCl) gives excellent performance in a lithium half‐cell by providing strong adsorption of the soluble Li₂S_x on the WS₂ with fast access to electrons from the current collector via a blocking carbon cloth interlayer.     

Metal Sulfide‐Decorated Carbon Sponge as a Highly Efficient Electrocatalyst and Absorbant for Polysulfide in High‐Loading Li2S Batteries

Owing to its high theoretical specific capacity (1166 mA h g^?1) and particularly its advantage to be paired with a lithium‐metal‐free anode, lithium sulfide (Li₂S) is regarded as a much safer cathode for next‐generation advanced lithium–sulfur (Li–S) batteries. However, the low conductivity of Li₂S and particularly the severe “polysulfide shuttle” of lithium polysulfide (LiPS) dramatically hinder their practical application in Li–S batteries. To address such issues, herein a bifuctional 3D metal sulfide‐decorated carbon sponge (3DTSC), which is constructed by 1D carbon nanowires cross‐linked with 2D graphene nanosheets with high conductivity and polar 0D metal sulfide nanodots with efficient electrocatalytic activity and strong chemical adsorption capability for LiPSs, is presented. Benefiting from the well‐designed multiscale, multidimensional 3D porous nanoarchitecture with high conductivity, and efficient electrocatalytic and absorption ability, the 3DTSC significantly mitigates LiPS shuttle, improves the utilization of Li₂S, and facilitates the transport of electrons and ions. As a result, even with a high Li₂S loading of 8 mg cm^?2, the freestanding 3DTSC‐Li₂S cathode without a polymer binder and metallic current collector delivers outstanding electrochemical performance with a high areal capacity of 8.44 mA h cm^?2.     

Nitrogen‐Doped Graphene‐Supported Mixed Transition‐Metal Oxide Porous Particles to Confine Polysulfides for Lithium–Sulfur Batteries

The intricate charge–discharge reactions and bad conductivity nature of sulfur determine the extreme importance of cathode engineering for Li–S batteries. Herein, spinel ZnCo₂O₄ porous particles@N‐doped reduced graphene oxide (ZnCo₂O₄@N‐RGO) are prepared via the combined procedures of refluxing and hydrothermal treatment, consisting of interconnected uniform ZnCo₂O₄ nanocubes with an average size of 5 nm anchored on graphene nanosheets. The as‐obtained composite can act as an inimitable cathode scaffold to suppress the shuttling of polysulfides by chemical confinement of ZnCo₂O₄ and N‐RGO for the first time, as demonstrated by the adsorption energy of ZnCo₂O₄ to Li₂S₄ via the strong chemical bonding between Zn or Co and S. The RGO nanosheets with a relatively high specific surface area provide a good conductive network and structural stability. The introduction of doped N atoms and numerous ZnCo₂O₄ porous nanoparticles can inhibit the transfer of lithium polysulfides between the cathode and anode. Due to the unique structural and compositional features, the as‐obtained hybrid materials with the high sulfur loading of 71% and even 82% still deliver high specific capacity, good rate capability, and enhanced cycling stability with exceptionally high initial Coulombic efficiency, which displays a high utilization of sulfur.     

Electrochemical Energy Storage with a Reversible Nonaqueous Room‐Temperature Aluminum–Sulfur Chemistry

A reversible room‐temperature aluminum–sulfur (Al‐S) battery is demonstrated with a strategically designed cathode structure and an ionic liquid electrolyte. Discharge–charge mechanism of the Al‐S battery is proposed based on a sequence of electrochemical, microscopic, and spectroscopic analyses. The electrochemical process of the Al‐S battery involves the formation of a series of polysulfides and sulfide. The high‐order polysulfides (S_x^2?, x ≥ 6) are soluble in the ionic liquid electrolyte. Electrochemical transitions between S₆^2? and the insoluble low‐order polysulfides or sulfide (S_x ^2?, 1 ≤ x < 6) are reversible. A single‐wall carbon nanotube coating applied to the battery separator helps alleviate the diffusion of the polysulfide species and reduces the polarization behavior of the Al‐S batteries.     

Optimized Catalytic WS2–WO3 Heterostructure Design for Accelerated Polysulfide Conversion in Lithium–Sulfur Batteries

The lithium–sulfur (Li–S) battery is a next generation high energy density battery, but its practical application is hindered by the poor cycling stability derived from the severe shuttling of lithium polysulfides (LiPSs). Catalysis is a promising way to solve this problem, but the rational design of relevant catalysts is still hard to achieve. This paper reports the WS₂–WO₃ heterostructures prepared by in situ sulfurization of WO₃, and by controlling the sulfurization degree, the structure is controlled, which balances the trapping ability (by WO₃) and catalytic activity (by WS₂) toward LiPSs. As a result, the WS₂–WO₃ heterostructures effectively accelerate LiPS conversion and improve sulfur utilization. The Li–S battery with 5 wt% WS₂–WO₃ heterostructures as additives in the cathode shows an excellent rate performance and good cycling stability, revealing a 0.06% capacity decay each cycle over 500 cycles at 0.5 C. By building an interlayer with such heterostructure‐added graphenes, the battery with a high sulfur loading of 5 mg cm^?2 still shows a high capacity retention of 86.1% after 300 cycles at 0.5 C. This work provides a rational way to prepare the metal oxide–sulfide heterostructures with an optimized structure to enhance the performance of Li–S batteries.     

Long‐Life,High‐Rate Lithium–Sulfur Cells with a Carbon‐Free VN Host as an Efficient Polysulfide Adsorbent and Lithium Dendrite Inhibitor

Lithium–sulfur (Li‐S) batteries are a promising next‐generation energy‐storage system, but the polysulfide shuttle and dendritic Li growth seriously hinder their commercial viability. Most of the previous studies have focused on only one of these two issues at a time. To address both the issues simultaneously, presented here is a highly conductive, noncarbon, 3D vanadium nitride (VN) nanowire array as an efficient host for both sulfur cathodes and lithium‐metal anodes. With fast electron and ion transport and high porosity and surface area, VN traps the soluble polysulfides, promotes the redox kinetics of sulfur cathodes, facilitates uniform nucleation/growth of lithium metal, and inhibits lithium dendrite growth at an unprecedented high current density of 10 mA cm^?2 over 200 h of repeated plating/stripping. As a result, VN‐Li||VN‐S full cells constructed with VN as both an anode and cathode host with a negative to positive electrode capacity ratio of only ≈2 deliver remarkable electrochemical performance with a high Coulombic efficiency of ≈99.6% over 850 cycles at a high 4 C rate and a high areal capacity of 4.6 mA h cm^?2. The strategy presented here offers a viable approach to realize high‐energy‐density, safe Li‐metal‐based batteries.     

Microemulsion Assisted Assembly of 3D Porous S/Graphene@g‐C3N4 Hybrid Sponge as Free‐Standing Cathodes for High Energy Density Li–S Batteries

A 3D porous sulfur/graphene@g‐C₃N₄ (S/GCN) hybrid sponge, which can be directly applied as a free‐standing cathode for Li–S batteries, is realized via a microemulsion assisted assembly approach. In this strategy, the interior oil emulsion droplets serve as soft templates to form pores to accommodate sulfur and the hydrophilic GCN stacks around oil droplets to assemble into a crosslinked 3D network. Through this microemulsion encapsulation route, S/GCN cathodes with a sulfur loading as high as 82 wt% can be achieved. Furthermore, the enriched N‐sites in GCN macropores offer numerous adhesion sites for polysulfides, realizing a “physical‐chemical” dual‐confinement for polysulfides from diffusion. Moreover, the robust and highly porous 3D graphene frameworks render efficient electron/Li⁺ transport pathways for fast kinetics as well as good structure integrity. Consequently, in comparison to the conventional G‐sponge/Li₂S_n catholyte system, S/GCN delivers a higher specific capacity, superior high‐rate capability (612 mA h g^?1 at 10 C), and alleviated anode corrosion issues. Particularly, an energy density as high as 1493 W h kg^?1 (calculated on the total weight of the cathode) and an extremely low capacity fading rate of 0.017% per cycle over 800 cycles at 0.3 C are achieved.     

Polysulfide‐Shuttle Control in Lithium‐Sulfur Batteries with a Chemically/Electrochemically Compatible NaSICON‐Type Solid Electrolyte

A NaSICON‐type Li⁺‐ion conductive membrane with a formula of Li_{1+ x} Y _x Zr_{2? x} (PO₄)₃ (LYZP) (x = 0–0.15) has been explored as a solid‐electrolyte/separator to suppress polysulfide‐crossover in lithium‐sulfur (Li‐S) batteries. The LYZP membrane with a reasonable Li⁺‐ion conductivity shows both favorable chemical compatibility with the lithium polysulfide species and exhibits good electrochemical stability under the operating conditions of the Li‐S batteries. Through an integration of the LYZP solid electrolyte with the liquid electrolyte, the hybrid Li‐S batteries show greatly enhanced cyclability in contrast to the conventional Li‐S batteries with the porous polymer (e.g., Celgard) separator. At a rate of C/5, the hybrid Li ||LYZP|| Li₂S₆ batteries developed in this study (with a Li‐metal anode, a liquid/LYZP hybrid electrolyte, and a dissolved lithium polysulfide cathode) delivers an initial discharge capacity of ≈1000 mA h g^?1 (based on the active sulfur material) and retains ≈90% of the initial capacity after 150 cycles with a low capacity fade‐rate of <0.07% per cycle.     

Highly Stable Lithium–Sulfur Batteries Based on Laponite Nanosheet‐Coated Celgard Separators

Lithium–sulfur (Li–S) batteries are of great interest due to their high theoretical energy density. However, one of the key issues hindering their real world applications is polysulfide shuttle, which results in severe capacity decay and self‐discharge. Here, a laponite nanosheets/carbon black coated Celgard (LNS/CB‐Celgard) separator to inhibit polysulfide shuttle and to enhance the Li⁺ conductivity simultaneously is reported. The polysulfide shuttle is efficiently inhibited through strong interactions between the O active sites of the LNS and polysulfides by forming the Li···O and O? S bonds. Moreover, the separator features high Li⁺ conductivity, fast Li⁺ diffusion, excellent electrolyte wettability, and high thermal stability. Consequently, the Li–S batteries with the LNS/CB‐Celgard separator and the pure S cathode show a high initial reversible capacity of 1387 mA h g^?1 at 0.1 C, high rate performance, superior cycling stability (with a capacity decay rate of 0.06% cycle^?1 at 0.2 C and 0.028% cycle^?1 at 1.0 C over 500 cycles), and ultralow self‐discharge. The separator could also enhance the performance of other batteries such as the LiFePO₄/separator/Li battery. This work sheds a new light on the design and preparation of novel separators for highly stable Li–S batteries via a “green” and cost‐effective approach.