Effect of optical panel distance in a photobioreactor for nutrient removal and cultivation of microalgae

The aim of present investigation is to assess the effect of illumination area and distance of an optical panel (OP) on the growth of microalgae with simultaneous removal of nutrients. Four different distances of OPs were used i.e. 225 mm OP (Run 1), 150 mm OP (Run 2), 112.5 mm OP (Run 3) and 90 mm distance OP (Run 4) in the photobioreactor (PBR) operations. The PBR was equipped with an OP and operated with a total volume of 37-l. A batch culture was prepared using an initial cell concentration of 1.12 ± 0.05 g l^?1. The experiments were conducted at neutral pH (7.2 ± 0.3) under dark and light cycles of 8 and 16 h, respectively. The diffuse light intensity was recorded as 91, 93, 95 and 98 % for Run 1, Run 2, Run 3 and Run 4, respectively, at a 300 mm depth level in the PBR. The chlorophyll content per cell was found to be an average of 701, 721, 785 and 808 fg for Run 1, Run 2, Run 3 and Run 4, respectively. High chlorophyll content per cell and diffuse light intensity was observed for Run 4 compared to other fractions. However, Run 3 sample possessed approximately 10.51 % higher biomass growth along with 15.22 % chemical oxygen demand, 18.15 % total nitrogen 2.37 % NH₄-N, 15.1 % total phosphorus and 15.05 % PO₄-P more removal than the Run 1. These findings suggest that in terms of economic consideration and efficiency of nutrients removal, Run 3 is found to be more effective than other samples. Moreover, an enhanced growth of Chlorella vulgaris could further be utilized as a potential biodiesel source.     

Simultaneous nutrient removal and lipid production from pretreated piggery wastewater by Chlorella vulgaris YSW-04

The feasibility of using a microalga Chlorella vulgaris YSW-04 was investigated for removal of nutrients from piggery wastewater effluent. The consequent lipid production by the microalga was also identified and quantitatively determined. The wastewater effluent was diluted to different concentrations ranging from 20 to 80 % of the original using either synthetic media or distilled water. The dilution effect on both lipid production and nutrient removal was evaluated, and growth rate of C. vulgaris was also monitored. Dilution of the wastewater effluent improved microalgal growth, lipid productivity, and nutrient removal. The growth rate of C. vulgaris was increased with decreased concentration of piggery wastewater in the culture media regardless of the diluent type. Lipid production was relatively higher when using synthetic media than using distilled water for dilution of wastewater. The composition of fatty acids accumulated in microalgal biomass was dependent upon both dilution ratio and diluent type. The microalga grown on a 20 % concentration of wastewater effluent diluted with distilled water was more promising for generating high-efficient biodiesel compared to the other culture conditions. The highest removal of inorganic nutrients was also achieved at the same dilution condition. Our results revealed the optimal pretreatment condition for the biodegradation of piggery wastewater with microalgae for subsequent production of high-efficient biodiesel.     

Phycoremediation of dairy and winery wastewater using <Emphasis Type="Italic">Diplosphaera</Emphasis> sp. MM1

A new green microalgal species was isolated, identified and investigated for its biomass production and nutrient removal efficiency in dairy and winery wastewater in this study. The 18S rRNA-based phylogenetic analysis revealed that this new strain is a Diplosphaera sp. and was designated strain MM1. The growth of this strain was evaluated in different diluted dairy and winery wastewaters. The highest algal biomass production (up to 2.3 g L^?1) was obtained in dairy wastewater (D3; dairy wastewater 1:2 deionised water) after 14 days of culture. However, for winery wastewater, the highest algal biomass production (up to 1.46 g L^?1) was obtained in wastewater combination W2 (winery wastewater 1:1 deionised water) after 14 days of culture. Turbid dairy wastewater with high concentration of nitrogen and phosphorous slowed down the initial growth of the alga. However, at the end of day 14, biomass production was nearly twofold higher than that of winery wastewater. The findings from both types of wastewater suggest that Diplosphaera sp. MM1 has potential for its application in generating biomass with simultaneous remediation of nutrient-rich wastewater.     

Cultivation of <Emphasis Type="Italic">Chlorella vulgaris</Emphasis> with swine wastewater and potential for algal biodiesel production

In this study, an alga-based simultaneous process of treating swine wastewater (SWW) and producing biodiesel was explored. Chlorella vulgaris (UTEX-265) was employed as a model species, and a SWW-based medium was prepared by dilution with tap water. Chlorella vulgaris grew well in the SWW-based medium, and at optimum dilution ratios, it exceeded the conventional culture medium in terms of biomass concentration and productivity. In eightfold diluted SWW, which supported the maximum growth, biomass productivity was 0.247 g L^?1 day^?1, while the productivity was merely 0.165 g L^?1 day^?1 in standard tris-acetate-phosphorous (TAP) algal medium. In addition, fatty acid methyl ester (FAME) productivity was greater in the SWW-based medium (0.067 versus 0.058 g L^?1 day^?1). This enhanced productivity resulted in more than 95 % removal of both nitrogen and phosphorous. All these show that C. vulgaris cultivation is indeed possible in a nutrient-rich wastewater with appropriate dilution, and in so doing, the wastewater can effectively be treated.     

Wastewater treatment and biofuel production through attached culture of <Emphasis Type="Italic">Chlorella vulgaris</Emphasis> in a porous substratum biofilm reactor

The feasibility of attached culture Chlorella vulgaris in a porous substratum biofilm reactor (PSBR) for simultaneous wastewater treatment and biofuel production was investigated. The characteristics, including algal biofilm growth, lipid yield, nutrient removal, and energy efficiency of the outdoor cultures, were investigated under the influence of both inoculum densities and the percent submerged area. A maximum biofilm productivity of 57.87 g m^?2 d^?1 with 81.9 % adhesion was achieved under optimal conditions (inoculum density of 18 g m^?2 and the percent submerged area of 5.7 %). The lipid content and lipid yield were 38.56 % and 27.25 g m^?2 d^?1, respectively. Meanwhile, the algae removed 99.95 % ammonia, 96.05 % total nitrogen (TN), and 99.83 % total phosphorus (TP). Further, the energy life cycle for the PSBR was analyzed. The biomass productivity per unit irradiance was up to 4.6 g MJ^?1 (photosynthetic efficiency of 10.65 %). The PSBR was considered to be economically feasible due to the net energy ratio of 1.3 (>1).     

Lipid production and composition of fatty acids in Chlorella vulgaris cultured using different methods: photoautotrophic,heterotrophic, and pure and mixed conditions

This study investigated the biomass, lipid production, fatty acid content, and other nutrients present in microorganisms by using four culture methods: (1) photoautotrophic pure Chlorella vulgaris cultures (PP); (2) heterotrophic pure C. vulgaris cultures (PH); (3) mixed cultures of Rhodotorula glutinis and C. vulgaris under photoautotrophic conditions (MP); and (4) heterotrophic mixed cultures (MH). The microorganisms in MP culture showed the optimum growth condition and lipid production. Among the cultures, MP yielded the highest number of cells and biomass (5.9?×?10⁵ cells/mL and 0.523 g/L, respectively). Furthermore, lipid production in MP culture was 114.22 mg/L, which is 136 % higher than that in MH culture (48.22 mg/L). Considering the higher contents of palmitic acid (C16:0) at 24.65 %, oleic acid (C18:1) at 56.34 %, and protein at 42.39 g/100 g in the MP culture than in other cultures, we proposed that MP could be used effectively to support the growth of microorganisms. This method could also be used as a potential approach for biodiesel production.     

Comparison of the culture and harvesting of <Emphasis Type="Italic">Chlorella vulgaris</Emphasis> and <Emphasis Type="Italic">Tetradesmus obliquus</Emphasis> for the removal of pharmaceuticals from water

The objective of this work was to assess and compare the removal efficiency of paracetamol and salicylic acid from aqueous medium by a microalgae-based treatment, using either Chlorella vulgaris or Tetradesmus obliquus. Moreover, considering microalgae application in wastewater treatment, the influence of these pharmaceuticals in the algal nutrient removal capacity was evaluated. The removal of paracetamol by T. obliquus (>40 %) was larger than by C. vulgaris (>21 %) in batch culture, and this was also observed for salicylic acid (>93 % by T. obliquus and >25 % by C. vulgaris). Both strains removed nutrients (phosphate and nitrate) almost completely by the end of the batch culture, but T. obliquus showed the highest efficiency at the steady state conditions of the semicontinuous culture. In spite of this, under the flocculants here tested, the efficiency in the recovery of biomass was much higher for C. vulgaris. These results highlight the importance of strain selection in the application of microalgae for wastewater treatment and, particularly, for the removal of pharmaceuticals.     

The effect of varying LED light sources and influent carbon/nitrogen ratios on treatment of synthetic sanitary sewage using Chlorella vulgaris

Sanitary sewage can create serious environmental problems if discharged directly into natural waters without appropriate treatment. This study showed that red light is the optimum light wavelength for growing microalgae Chlorella vulgaris in microalgae biological wastewater treatment systems, given a harvest time of 144 h. Only moderate light intensities (1,000, 1,500, 2,000, and 2,500 μmol m^?2 s^?1) were able to remove nutrients from synthetic sanitary sewage, but higher light intensity led to better nutrient removal effects. Because of economic considerations, the optimum light intensity range for efficient nutrient removal was determined to be between 1,500 and 2,000 μmol m^?2 s^?1. Furthermore, nutrient removal efficiency was significantly affected by light wavelength, light intensity, the interaction of these two factors, and the interaction among light wavelength, light intensity, and influent carbon/nitrogen (C/N) ratios. Total nitrogen and total phosphorus removal efficiency was also significantly affected by influent C/N ratios. Appropriate control of carbon and nitrogen source concentrations enabled optimal nutrient removal. The optimal influent C/N ratio was determined to be 6:1.     

Phosphorus runoff from a phosphorus deficient soil under common bean (Phaseolus vulgaris L.) and soybean (Glycine max L.) genotypes with contrasting root architecture

The selection and breeding of crop genotypes with root traits that improve soil resource extraction is a promising avenue to improved nutrient and water use efficiency in low-input farming systems. Such genotypes may accelerate nutrient extraction (“nutrient mining”), but may also reduce nutrient loss via soil erosion by producing greater shoot biomass and by direct effects of root traits on aggregate formation and water infiltration. Little is known about the effects of root architecture on phosphorus (P) runoff and soil erosion, and the relative importance of root and shoot traits on runoff P loss has not been determined. Four genotypes of common bean (Phaseolus vulgaris L.) and two genotypes of soybean (Glycine max) selected for contrasting root architecture were grown in a low P soil (Aquic Fragiudult, <20 mg kg^?1 Mehlich-3 P, 3% slope) and subjected to rainfall-runoff experiments with and without shoot removal. Plots with intact shoots had significantly lower runoff volumes (1.3–7.6 mm) and total P loads in runoff (0.005–0.32 kg ha^?1) than plots with shoots removed (7.0–16.8 mm; 0.025–1.95 kg ha^?1). Dissolved reactive P leached from plant material did not contribute significantly to P loss in runoff. Total root length acquired from soil cores differed significantly among genotypes. Root length densities in the upper 15 cm of soil mid-way between rows were less than 4.0 cm cm^?3 and variation in root length density was not correlated with runoff or P loss. Root length density also did not affect rainfall infiltration or surface runoff volume. We conclude that for annual dicotyledonous crops such as bean and soybean with relatively low root length densities, root traits have little direct effect on soil erosion.     

Optimization of CO2 concentration and light intensity for biodiesel production by Chlorella vulgaris FACHB-1072 under nitrogen deficiency with phosphorus luxury uptake

Microalgal biodiesel is an alternative bioenergy for the future. Nitrogen deprivation is usually used to increase lipid content in microalgae, however, it also lowers biomass production, resulting in not much increase of lipid productivity. Our previous study found that phosphorus played an important role in enhancing biodiesel productivity of C. vulgaris FACHB-1072 under nitrogen deficient condition. The aim of this study was to optimize two significant parameters of CO₂ concentration (0.03, 4, 6, 12 %) and light intensity (40, 120, 200 μmol photons m^-2 s^-1) with respect to biodiesel productivity and P uptake rate of C. vulgaris FACHB-1072. It was found that the optimized conditions were 4 % CO₂ concentration and 200 μmol photons m^-2 s^-1 light intensity. The maximum biodiesel productivity was 34.56 mg L^-1 day^-1; 2.7 times higher than the control (nutrient sufficient condition). Phosphorus was accumulated as polyphosphate and its maximum uptake rate was 2.08 mg L^-1 day^-1; twice that of the control. After optimization, the performances under nitrogen deficiency were significantly better compared with those under nitrogen sufficiency, which were rarely reported in literature. Our findings suggest a great potential to combine phosphorus removal from wastewater with biodiesel production via microalgae.     

Seasonal variation in light utilisation,biomass production and nutrient removal by wastewater microalgae in a full-scale high-rate algal pond

There has been renewed interest in the combined use of high-rate algal ponds (HRAP) for wastewater treatment and biofuel production. Successful wastewater treatment requires year-round efficient nutrient removal while high microalgal biomass yields are required to make biofuel production cost-effective. This paper investigates the year-round performance of microalgae in a 5-ha demonstration HRAP system treating primary settled wastewater in Christchurch, New Zealand. Microalgal performance was measured in terms of biomass production, nutrient removal efficiency, light absorption and photosynthetic potential on seasonal timescales. Retention time-corrected microalgal biomass (chlorophyll a) varied seasonally, being lowest in autumn and winter (287 and 364 mg m^?3day^?1, respectively) and highest in summer (703 mg m^?3day^?1), while the conversion efficiency of light to biomass was greatest in winter (0.39 mg Chl- a per μmol) and lowest in early summer (0.08 mg Chl- a per μmol). The percentage of ammonium (NH₄–N) removed was highest in spring (79 %) and summer (77 %) and lowest in autumn (47 %) and winter (53 %), while the efficiency of NH₄–N removal per unit biomass was highest in autumn and summer and lowest in winter and spring. Chlorophyll-specific light absorption per unit biomass decreased as total chlorophyll increased, partially due to the package effect, particularly in summer. The proportional increase in the maximum electron transport rate from winter to summer was significantly lower than the proportional increase in the mean light intensity of the water column. We concluded that microalgal growth and nutrient assimilation was constrained in spring and summer and carbon limitation may be the likely cause.     

Evaluation of microalgal consortia for treatment of primary treated sewage effluent and biomass production

The present investigation was aimed towards analyzing the potential of consortia of native filamentous microalgal strains (MC2), native unicellular microalgal strains (MC3), and selected microalgae from germplasm (MC1) in terms of nutrient removal, water quality improvement, and biomass production using primary treated sewage water. Highest NO₃-N (90 %) and PO₄-P (97.8 %) removal was obtained with MC2-inoculated sewage water. Highest decrease in total dissolved solids to 806 from 1,120 mg L^?1 and highest increase in dissolved oxygen of 9.0 from 0.4 mg L^?1 were obtained using MC2-inoculated sewage water on the sixth day. The biomass production was also highest in MC2 (1.07 g L^?1) followed by MC1 and MC3 (0.90 and 0.94 g L^?1, respectively) on the sixth day. The consortium of filamentous strains from native environment not only proved promising in nutrient removal efficiency but also led to enhanced biomass. The present study highlighted the utility of such a consortium for sewage wastewater treatment and the promise of sewage water as a growth medium for biomass production.     

Effect of Potassium and Nitrogen Fertilizer on Switchgrass Productivity and Nutrient Removal Rates under Two Harvest Systems on a Low Potassium Soil

Biomass demand for energy will lead to utilization of marginal, low fertility soil. Application of fertilizer to such soil may increase switchgrass (Panicum virgatum L.) biomass production. In this three-way factorial field experiment, biomass yield response to potassium (K) fertilizer (0 and 68 kg?K?ha^?1) on nitrogen (N)-sufficient and N-deficient switchgrass (0 and 135 kg?N?ha^?1) was evaluated under two harvest systems. Harvest system included harvesting once per year after frost (December) and twice per year in summer (July) at boot stage and subsequent regrowth after frost. Under the one-cut system, there was no response to N or K only (13.4 Mg?ha^?1) compared to no fertilizer (12.4 Mg?ha^?1). Switchgrass receiving both N and K (14.6 Mg?ha^?1) produced 18 % greater dry matter (DM) yield compared to no fertilizer check. Under the two-cut harvest system, N only (16.0 Mg?ha^?1) or K only (14.1 Mg?ha^?1) fertilizer produced similar DM to no fertilizer (15.1 Mg?ha^?1). Switchgrass receiving both N and K in the two-cut system (19.2 Mg?ha^?1) produced the greatest (P?<?0.05) DM yield, which was 32 % greater than switchgrass receiving both N and K in the one-cut system. Nutrient removal (biomass?×?nutrient concentration) was greatest in plots receiving both N and K, and the two-cut system had greater nutrient removal than the one-cut system. Based on these results, harvesting only once during winter months reduces nutrient removal in harvested biomass and requires less inorganic fertilizer for sustained yields from year to year compared to two-cut system.     

Biological CO<Subscript>2</Subscript> fixation using C<Emphasis Type="Italic">hlorella vulgaris</Emphasis> and its thermal characteristics through thermogravimetric analysis

The present research is focused on cultivation of microalgae strain Chlorella vulgaris for bio-fixation of CO₂ coupled with biomass production. In this regard, a single semi-batch vertical tubular photobioreactor and four similar photobioreactors in series have been employed. The concentration of CO₂ in the feed stream was varied from 2 to 12 % (v/v) by adjusting CO₂ to air ratio. The amount of CO₂ capture and algae growth were monitored by measuring decrease of CO₂ concentration in the gas phase, microalgal cell density, and algal biomass production rate. The results show that 4 % CO₂ gives maximum amount of biomass (0.9 g L^?1) and productivity (0.118 g L^?1 day^?1) of C. vulgaris in a single reactor. In series reactors, average productivity per reactor found to be 0.078 g L^?1 day^?1. The maximum CO₂ uptake for single reactor also found with 4 % CO_2, and it is around 0.2 g L^?1 day^?1. In series reactors, average CO₂ uptake is 0.13 g L^?1 day^?1 per reactor. TOC analysis shows that the carbon content of the produced biomass is around 40.67 % of total weight. The thermochemical characteristics of the cultivated C. vulgaris samples were analyzed in the presence of air. All samples burn above 200 °C and the combustion rate become faster at around 600 °C. Almost 98 wt% of the produced biomass is combustible in this range.     

Simultaneous wastewater treatment,electricity generation and biomass production by an immobilized photosynthetic algal microbial fuel cell

A photosynthetic algal microbial fuel cell (PAMFC) was constructed by the introduction of immobilized microalgae (Chlorella vulgaris) into the cathode chamber of microbial fuel cells to fulfill electricity generation, biomass production and wastewater treatment. The immobilization conditions, including the concentration of immobilized matrix, initial inoculation concentration and cross-linking time, were investigated both for the growth of C. vulgaris and power generation. It performed the best at 5 % sodium alginate and 2 % calcium chloride as immobilization matrix, initial inoculation concentration of 10⁶ cell/mL and cross-linking time of 4 h. Our findings indicated that C. vulgaris immobilization was an effective and promising approach to improve the performance of PAMFC, and after optimization the power density and Coulombic efficiency improved by 258 and 88.4 %, respectively. Important parameters such as temperature and light intensity were optimized on the performance. PAMFC could achieve a COD removal efficiency of 92.1 %, and simultaneously the maximum power density reached 2,572.8 mW/m³ and the Coulombic efficiency was 14.1 %, under the light intensity of 5,000 lux and temperature at 25 °C.     

Comparison of biomass production and total lipid content of freshwater green microalgae cultivated under various culture conditions

The growth and total lipid content of four green microalgae (Chlorella sp., Chlorella vulgaris CCAP211/11B, Botryococcus braunii FC124 and Scenedesmus obliquus R8) were investigated under different culture conditions. Among the various carbon sources tested, glucose produced the largest biomass or microalgae grown heterotrophically. It was found that 1 % (w/v) glucose was actively utilized by Chlorella sp., C. vulgaris CCAP211/11B and B. braunii FC124, whereas S. obliquus R8 preferred 2 % (w/v) glucose. No significant difference in biomass production was noted between heterotrophic and mixotrophic (heterotrophic with light illumination/exposure) growth conditions, however, less production was observed for autotrophic cultivation. Total lipid content in cells increased by approximately two-fold under mixotrophic cultivation with respect to heterotrophic and autotrophic cultivation. In addition, light intensity had an impact on microalgal growth and total lipid content. The highest total lipid content was observed at 100 μmol m^?2s^?1 for Chlorella sp. (22.5 %) and S. obliquus R8 (23.7 %) and 80 μmol m^?2s^?1 for C. vulgaris CCAP211/11B (20.1 %) and B. braunii FC124 (34.9 %).     

Comparison of <Emphasis Type="Italic">Chlorella vulgaris</Emphasis> and cyanobacterial biomass: cultivation in urban wastewater and methane production

Anaerobic digestion of microalgae is hampered by its complex cell wall. Against this background, cyanobacteria cell walls render this biomass as an ideal substrate for overcoming this drawback. The aim of the present study was to compare the growth of two cyanobacteria (Aphanizomenon ovalisporum and Anabaena planctonica) and a microalga (Chlorella vulgaris) in urban wastewater when varying the temperature (22, 27 and 32 °C). Cyanobacterial optimal growth for both strains was attained at 22 °C, while C. vulgaris did not show remarkable differences among temperatures. For all the microorganisms, ammonium removal was higher than phosphate. Biomass collected was subjected to anaerobic digestion. Methane yield of C. vulgaris was 184.8 mL CH₄ g COD in^?1 while with A. ovalisporum and A. planctonica the methane production was 1.2- and 1.4-fold higher. This study showed that cyanobacteria growth rates could be comparable to microalgae while presenting the additional benefit of an increased anaerobic digestibility.     

Euglena sp. as a suitable source of lipids for potential use as biofuel and sustainable wastewater treatment

Prolific algal growth in sewage ponds with high organic loads in the tropical regions can provide cost-effective and efficient wastewater treatment and biofuel production. This work examines the ability of Euglena sp. growing in wastewater ponds for biofuel production and treatment of wastewater. The algae were isolated from the sewage treatment plants and were tested for their nutrient removal capability. Compared to other algae, Euglena sp. showed faster growth rates with high biomass density at elevated concentrations of ammonium nitrogen (NH₄-N) and organic carbon (C). Profuse growth of these species was observed in untreated wastewaters with a mean specific growth rate (μ) of 0.28 day^?1 and biomass productivities of 132 mg ?L^?1? day^?1. The algae cultured within a short period of 8 days resulted in the 98 % removal of NH₄-N, 93 % of total nitrogen 85 % of ortho-phosphate, 66 % of total phosphate and 92 % total organic carbon. Euglenoids achieved a maximum lipid content of 24.6 % (w/w) with a biomass density of 1.24 g ?L^?1 (dry wt.). Fourier transform infrared spectra showed clear transitions in biochemical compositions with increased lipid/protein ratio at the end of the culture. Gas chromatography and mass spectrometry indicated the presence of high contents of palmitic, linolenic and linoleic acids (46, 23 and 22 %, respectively), adding to the biodiesel quality. Good lipid content (comprised quality fatty acids), efficient nutrient uptake and profuse biomass productivity make the Euglena sp. as a viable source for biofuel production in wastewaters.     

Carbon dioxide and poultry waste utilization for production of polyhydroxyalkanoate biopolymers by <Emphasis Type="Italic">Nostoc muscorum</Emphasis> Agardh: a sustainable approach

The new paradigm is to view wastes as resources for sustainable development. In this regard, the feasibility of poultry waste and CO₂ utilization for cultivation of a filamentous nitrogen-fixing cyanobacterium, Nostoc muscorum Agardh, was investigated for production polyhydroxyalkanoates, the biodegradable polymers. This cyanobacterium showed profound rise in biomass yield with up to 10 % CO₂ supply in airstream with an aeration rate of 0.1 vvm. Maximum biomass yield of 1.12 g L^?1 was recorded for 8 days incubation period, thus demonstrating a CO₂ biofixation rate of 0.263 g L^?1 day^?1 at 10 % (v/v) CO₂-enriched air. Poultry litter (PL) supplementation also had a positive impact on the biomass yield. The nutrient removal efficiency of N. muscorum was reflected in the significant reduction in nutrient load of PL over the experimental period. A maximum poly(3-hydroxybutyric acid-co-3-hydroxyvaleric acid) [P(3HB-co-3HV)] copolymer yield of 774 mg L^?1 (65 % of dry cell wt.), the value almost 11-fold higher than the control, was recorded in 10 g L^?1 PL-supplemented cultures with 10 % CO₂ supply under the optimized condition, thus demonstrating that N. muscorum has good potential for CO₂ biomitigation and poultry waste remediation while simultaneously producing eco-friendly polymers.     

Investigation of mixotrophic,heterotrophic, and autotrophic growth of Chlorella vulgaris under agricultural waste medium

Growth of Chlorella vulgaris and its lipid production were investigated under autotrophic, heterotrophic, and mixotrophic conditions. Cheap agricultural waste molasses and corn steep liquor from industries were used as carbon and nitrogen sources, respectively. Chlorella vulgaris grew remarkably under this agricultural waste medium, which resulted in a reduction in the final cost of the biodiesel production. Maximum dry weight of 2.62 g L^?1 was obtained in mixotrophic growth with the highest lipid concentration of 0.86 g L^?1. These biomass and lipid concentrations were, respectively, 140% and 170% higher than autotrophic growth and 300% and 1200% higher than heterotrophic growth. In mixotrophic growth, independent or simultaneous occurrence of autotrophic and heterotrophic metabolisms was investigated. The growth of the microalgae was observed to take place first heterotrophically to a minimum substrate concentration with a little fraction in growth under autotrophic metabolism, and then the cells grew more autotrophically. It was found that mixotrophic growth was not a simple combination of heterotrophic and autotrophic growth.