Correlating Macro and Atomic Structure with Elastic Properties and Ionic Transport of Glassy Li2S‐P2S5 (LPS) Solid Electrolyte for Solid‐State Li Metal Batteries

A combination of high ionic conductivity and facile processing suggest that sulfide‐based materials are promising solid electrolytes that have the potential to enable Li metal batteries. Although the Li₂S‐P₂S₅ (LPS) family of compounds exhibit desirable characteristics, it is known that Li metal preferentially propagates through microstructural defects, such as particle boundaries and/or pores. Herein, it is demonstrated that a near theoretical density (98% relative density) LPS 75‐25 glassy electrolyte exhibiting high ionic conductivity can be achieved by optimizing the molding pressure and temperature. The optimal molding pressure reduces porosity and particle boundaries while preserving the preferred amorphous structure. Moreover, molecular rearrangements and favorable Li coordination environments for conduction are attained. Consequently, the Young's Modulus approximately doubles (30 GPa) and the ionic conductivity increases by a factor of five (1.1 mS cm^?1) compared to conventional room temperature molding conditions. It is believed that this study can provide mechanistic insight into processing‐structure‐property relationships that can be used as a guide to tune microstructural defects/properties that have been identified to have an effect on the maximum charging current that a solid electrolyte can withstand during cycling without short‐circuiting.     

Electrochemical Stability of Li10GeP2S12 and Li7La3Zr2O12 Solid Electrolytes

The electrochemical stability window of solid electrolyte is overestimated by the conventional experimental method using a Li/electrolyte/inert metal semiblocking electrode because of the limited contact area between solid electrolyte and inert metal. Since the battery is cycled in the overestimated stability window, the decomposition of the solid electrolyte at the interfaces occurs but has been ignored as a cause for high interfacial resistances in previous studies, limiting the performance improvement of the bulk‐type solid‐state battery despite the decades of research efforts. Thus, there is an urgent need to identify the intrinsic stability window of the solid electrolyte. The thermodynamic electrochemical stability window of solid electrolytes is calculated using first principles computation methods, and an experimental method is developed to measure the intrinsic electrochemical stability window of solid electrolytes using a Li/electrolyte/electrolyte‐carbon cell. The most promising solid electrolytes, Li₁₀GeP₂S₁₂ and cubic Li‐garnet Li₇La₃Zr₂O₁₂, are chosen as the model materials for sulfide and oxide solid electrolytes, respectively. The results provide valuable insights to address the most challenging problems of the interfacial stability and resistance in high‐performance solid‐state batteries.     

Rational Design of Hierarchical “Ceramic‐in‐Polymer” and “Polymer‐in‐Ceramic” Electrolytes for Dendrite‐Free Solid‐State Batteries

Solid polymer electrolytes as one of the promising solid‐state electrolytes have received extensive attention due to their excellent flexibility. However, the issues of lithium (Li) dendrite growth still hinder their practical applications in solid‐state batteries (SSBs). Herein, composite electrolytes from “ceramic‐in‐polymer” (CIP) to “polymer‐in‐ceramic” (PIC) with different sizes of garnet particles are investigated for their effectiveness in dendrite suppression. While the CIP electrolyte with 20 vol% 200 nm Li_6.4La₃Zr_1.4Ta_0.6O₁₂ (LLZTO) particles (CIP‐200 nm) exhibits the highest ionic conductivity of 1.6 × 10^?4 S cm^?1 at 30 °C and excellent flexibility, the PIC electrolyte with 80 vol% 5 µm LLZTO (PIC‐5 µm) shows the highest tensile strength of 12.7 MPa. A sandwich‐type composite electrolyte (SCE) with hierarchical garnet particles (a PIC‐5 µm interlayer sandwiched between two CIP‐200 nm thin layers) is constructed to simultaneously achieve dendrite suppression and excellent interfacial contact with Li metal. The SCE enables highly stable Li plating/stripping cycling for over 400 h at 0.2 mA cm^?2 at 30 °C. The LiFePO₄/SCE/Li cells also demonstrate excellent cycle performance at room temperature. Fabricating sandwich‐type composite electrolytes with hierarchical filler designs can be an effective strategy to achieve dendrite‐free SSBs with high performance and high safety at room temperature.     

Viscoelastic and Nonflammable Interface Design–Enabled Dendrite‐Free and Safe Solid Lithium Metal Batteries

Herein, a composite polymer electrolyte with a viscoelastic and nonflammable interface is designed to handle the contact issue and preclude Li dendrite formation. The composite polymer electrolyte (cellulose acetate/polyethylene glycol/Li_1.4Al_0.4Ti_1.6P₃O₁₂) exhibits a wide electrochemical window of 5 V (vs Li⁺/Li), a high Li⁺ transference number of 0.61, and an excellent ionic conductivity of above 10^?4 S cm^?1 at 60 °C. In particular, the intimate contact, low interfacial impedance, and fast ion‐transport process between the electrodes and solid electrolytes can be simultaneously achieved by the viscoelastic and nonflammable layer. Benefiting from this novel design, solid lithium metal batteries with either LiFePO₄ or LiCoO₂ as cathode exhibit superior cyclability and rate capability, such as a discharge capacity of 157 mA h g^?1 after 100 cycles at C/2 and 97 mA h g^?1 at 5C for LiFePO₄ cathode. Moreover, the smooth and uniform Li surface after long‐term cycling confirms the successful suppression of dendrite formation. The viscoelastic and nonflammable interface modification of solid electrolytes provides a promising and general strategy to handle the interfacial issues and improves the operative safety of solid lithium metal batteries.     

Nonwoven rGO Fiber‐Aramid Separator for High‐Speed Charging and Discharging of Li Metal Anode

Li metal, which has a high theoretical specific capacity and low redox potential, is considered to the most promising anode material for next‐generation Li ion‐based batteries. However, it also exhibits a disadvantageous solid electrolyte interphase (SEI) layer problem that needs to be resolved. Herein, an advanced separator composed of reduced graphene oxide fiber attached to aramid paper (rGOF‐A) is introduced. When rGOF‐A is applied, F^? anions, generated from the decomposition of the LiPF₆ electrolyte during the SEI layer formation process form semi‐ionic C? F bonds along the surface of rGOF. As Li⁺ ions are plated, the “F‐doped” rGO surface induces the formation of LiF, which is known as a component of a chemically stable SEI, therefore it helps the Li metal anode to operate stably at a high current of 20 mA cm^?2 with a high capacity of 20 mAh cm^?2. The proposed rGOF‐A separator successfully achieves a stable SEI layer that could resolve the interfacial issues of the Li metal anode.     

Tailoring Lithium Deposition via an SEI‐Functionalized Membrane Derived from LiF Decorated Layered Carbon Structure

Lithium (Li) metal is a key anode material for constructing next generation high energy density batteries. However, dendritic Li deposition and unstable solid electrolyte interphase (SEI) layers still prevent practical application of Li metal anodes. In this work, it is demonstrated that an uniform Li coating can be achieved in a lithium fluoride (LiF) decorated layered structure of stacked graphene (SG), leading to the formation of an SEI‐functionalized membrane that retards electron transfer by three orders of magnitude to avoid undesirable Li deposition on the top surface, and ameliorates Li⁺ ion migration to enable uniform and dendrite‐free Li deposition beneath such an interlayer. Surface chemistry analysis and density functional theory calculations demonstrate that these beneficial features arise from the formation of C–F_x surface components on the SG sheets during the Li coating process. Based on such an SEI‐functionalized membrane, stable cycling at high current densities up to 3 mA cm^?2 and Li plating capacities up to 4 mAh cm^?2 can be realized in LiPF₆/carbonate electrolytes. This work elucidates the promising strategy of modifying Li plating behavior through the SEI‐functionalized carbon structure, with significantly improved cycling stability of rechargeable Li metal anodes.     

Slurry‐Fabricable Li+‐Conductive Polymeric Binders for Practical All‐Solid‐State Lithium‐Ion Batteries Enabled by Solvate Ionic Liquids

For mass production of all‐solid‐state lithium‐ion batteries (ASLBs) employing highly Li⁺ conductive and mechanically sinterable sulfide solid electrolytes (SEs), the wet‐slurry process is imperative. Unfortunately, the poor chemical stability of sulfide SEs severely restrict available candidates for solvents and in turn polymeric binders. Moreover, the binders interrupt Li⁺‐ionic contacts at interfaces, resulting in the below par electrochemical performance. In this work, a new scalable slurry fabrication protocol for sheet‐type ASLB electrodes made of Li⁺‐conductive polymeric binders is reported. The use of intermediate‐polarity solvent (e.g., dibromomethane) for the slurry allows for accommodating Li₆PS₅Cl and solvate‐ionic‐liquid‐based polymeric binders (NBR‐Li(G3)TFSI, NBR: nitrile?butadiene rubber, G3: triethylene glycol dimethyl ether, LiTFSI: lithium bis(trifluoromethanesulfonyl)imide) together without suffering from undesirable side reactions or phase separation. The LiNi_0.6Co_0.2Mn_0.2O₂ and Li₄Ti₅O₁₂ electrodes employing NBR‐Li(G3)TFSI show high capacities of 174 and 160 mA h g^?1 at 30 °C, respectively, which are far superior to those using conventional NBR (144 and 76 mA h g^?1). Moreover, high areal capacity of 7.4 mA h cm^?2 is highlighted for the LiNi_0.7Co_0.15Mn_0.15O₂ electrodes with ultrahigh mass loading of 45 mg cm^?2. The facilitated Li⁺‐ionic contacts at interfaces paved by NBR‐Li(G3)TFSI are evidenced by the complementary analysis from electrochemical and ⁷Li nuclear magnetic resonance measurements.     

A Lithium Amide‐Borohydride Solid‐State Electrolyte with Lithium‐Ion Conductivities Comparable to Liquid Electrolytes

High ionic conductivity of up to 6.4 × 10^?3 S cm^?1 near room temperature (40 °C) in lithium amide‐borohydrides is reported, comparable to values of liquid organic electrolytes commonly employed in lithium‐ion batteries. Density functional theory is applied coupled with X‐ray diffraction, calorimetry, and nuclear magnetic resonance experiments to shed light on the conduction mechanism. A Li₄Ti₅O₁₂ half‐cell battery incorporating the lithium amide‐borohydride electrolyte exhibits good rate performance up to 3.5 mA cm^?2 (5 C) and stable cycling over 400 cycles at 1 C at 40 °C, indicating high bulk and interfacial stability. The results demonstrate the potential of lithium amide‐borohydrides as solid‐state electrolytes for high‐power lithium‐ion batteries.     

Solvent‐Free Synthesis of Thin,Flexible, Nonflammable Garnet‐Based Composite Solid Electrolyte for All‐Solid‐State Lithium Batteries

Thin solid‐state electrolytes with nonflammability, high ionic conductivity, low interfacial resistance, and good processability are urgently required for next‐generation safe, high energy density lithium metal batteries. Here, a 3D Li_6.75La₃Zr_1.75Ta_0.25O₁₂ (LLZTO) self‐supporting framework interconnected by polytetrafluoroethylene (PTFE) binder is prepared through a simple grinding method without any solvent. Subsequently, a garnet‐based composite electrolyte is achieved through filling the flexible 3D LLZTO framework with a succinonitrile solid electrolyte. Due to the high content of garnet ceramic (80.4 wt%) and high heat‐resistance of the PTFE binder, such a composite electrolyte film with nonflammability and high processability exhibits a wide electrochemical window of 4.8 V versus Li/Li⁺ and high ionic transference number of 0.53. The continuous Li⁺ transfer channels between interconnected LLZTO particles and succinonitrile, and the soft electrolyte/electrode interface jointly contribute to a high ambient‐temperature ionic conductivity of 1.2 × 10^?4 S cm^?1 and excellent long‐term stability of the Li symmetric battery (stable at a current density of 0.1 mA cm^?2 for over 500 h). Furthermore, as‐prepared LiFePO₄|Li and LiNi_0.5Mn_0.3Co_0.2O₂|Li batteries based on the thin composite electrolyte exhibit high discharge specific capacities of 153 and 158 mAh g^?1 respectively, and desirable cyclic stabilities at room temperature.     

3D Vertically Aligned Li Metal Anodes with Ultrahigh Cycling Currents and Capacities of 10 mA cm−2/20 mAh cm−2 Realized by Selective Nucleation within Microchannel Walls

Although metallic lithium is regarded as the “Holy Grail” for next‐generation rechargeable batteries due to its high theoretical capacity and low overpotential, the uncontrollable Li dendrite growth, especially under high current densities and deep plating/striping, has inhibited its practical application. Herein, a 3D‐printed, vertically aligned Li anode (3DP‐VALi) is shown to efficiently guide Li deposition via a “nucleation within microchannel walls” process, enabling a high‐performance, dendrite‐free Li anode. Moreover, the microchannels within the microwalls are beneficial for promoting fast Li⁺ diffusion, supplying large space for the accommodation of Li during the plating/stripping process. The high‐surface‐area 3D anode design enables high operating current densities and high areal capacities. As a result, the Li–Li symmetric cells using 3DP‐VALi demonstrate excellent electrochemical performances as high as 10 mA cm^?2/10 mAh cm^?2 for 1500 h and 5 mA cm^?2/20 mAh cm^?2 for 400 h, respectively. Additionally, the Li–S and Li–LiFePO₄ cells using 3DP‐VALi anodes present excellent cycling stability up to 250 and 800 cycles at a rate of 1 C, respectively. It is believed that these new findings could open a new window for dendrite‐free metal anode design and pave the way toward energy storage devices with high energy/power density.     

In Situ Generation of Artificial Solid‐Electrolyte Interphases on 3D Conducting Scaffolds for High‐Performance Lithium‐Metal Anodes

Rational structure design of the current collector along with further engineering of the solid‐electrolyte interphases (SEI) layer is one of the most promising strategies to achieve uniform Li deposition and inhibit uncontrolled growth of Li dendrites. Here, a Li₂S layer as an artificial SEI with high compositional uniformity and high lithium ion conductivity is in situ generated on the surface of the 3D porous Cu current collector to regulate homogeneous Li plating/stripping. Both simulations and experiments demonstrate that the Li₂S protective layer can passivate the porous Cu skeleton and balance the transport rate of lithium ions and electrons, thereby alleviating the agglomerated Li deposition at the top of the electrode or at the defect area of the SEI layer. As a result, the modified current collector exhibits long‐term cycling of 500 cycles at 1 mA cm^?2 and stable electrodeposition capabilities of 4 mAh cm^?2 at an ultrahigh current density of 4 mA cm^?2. Furthermore, full batteries (LiFePO₄ as cathode) paired with this designed 3D anode with only ≈200% extra lithium show superior stability and rate performance than the batteries paired with lithium foil (≈3000% extra lithium). These explorations provide new strategies for developing high‐performance Li metal anodes.     

Germanium Thin Film Protected Lithium Aluminum Germanium Phosphate for Solid‐State Li Batteries

Solid‐state Li batteries using Na⁺ superionic conductor type solid electrolyte attracts wide interest because of its safety and high theoretical energy density. The NASCION type solid electrolyte LAGP (Li_1.5Al_0.5Ge_0.5P₃O₁₂) shows favorable conductivity as well as good mechanical strength to prevent Li dendrite penetration. However, the instability of LAGP with Li metal remains a great challenge. In this work, an amorphous Ge thin film is sputtered on an LAGP surface, which can not only suppress the reduction reaction of Ge⁴⁺ and Li, but also produces intimate contact between the Li metal and the LAGP solid electrolyte. The symmetric cell with the Ge‐coated LAGP solid electrolyte shows superior stability and cycle performance for 100 cycles at 0.1 mA cm^?2. A quasi‐solid‐state Li–air battery has also been assembled to further demonstrate this advantage. A stable cycling performance of 30 cycles in ambient air can be obtained. This work helps to achieve a stable and ionic conducting interface in solid‐state Li batteries.     

Constructing Multifunctional Interphase between Li1.4Al0.4Ti1.6(PO4)3 and Li Metal by Magnetron Sputtering for Highly Stable Solid‐State Lithium Metal Batteries

Due to high ionic conductivity and low cost, Li_1.4Al_0.4Ti_1.6(PO₄)₃ (LATP) has emerged as a promising solid‐state electrolyte for next‐generation lithium (Li) metal solid‐state batterie with high safety performance and energy density. However, the extremely high impedance and surface instability of LATP with Li metal retard its practical application. Herein, a novel method is proposed to construct an ultrathin ZnO layer that is tightly coated on the LATP pellets, surface (ZnO@LATP) via magnetron sputtering, which in situ reacts with Li to form a low electronic conductivity and multifunctional solid electrolyte interphase (SEI). The formed SEI can not only effectively lower the interfacial resistance, but also overcome the side reactions of LATP with the Li metal anode and suppress the Li dendrite growth. Specifically, the interface resistance decreases from 80 554 to 353 Ω and the overpotential reduces from 1 V to 20 mV. As a result, the Li/ZnO@LATP@ZnO/Li symmetric batteries can stably cycle for more than 2000 h without short circuit at 0.05 mA cm^?2 and Li/ZnO@LATP/LiFePO₄ batteries show excellent cycle stability for 200 cycles at 0.1 C. This work highlights the significance of multifunctional interphase between LATP and Li metal for improvement of interfacial impedance and instability.     

Li+ Pre‐Insertion Leads to Formation of Solid Electrolyte Interface on TiO2 Nanotubes That Enables High‐Performance Anodes for Sodium Ion Batteries

Recently, sodium ion batteries (SIBs) have been widely investigated as one of the most promising candidates for replacing lithium ion batteries (LIBs). For SIBs or LIBs, designing a stable and uniform solid electrolyte interphase (SEI) at the electrode–electrolyte interface is the key factor to provide high capacity, long‐term cycling, and high‐rate performance. In this paper, it is described how a remarkably enhanced SEI layer can be obtained on TiO₂ nanotube (TiO₂ NTs) arrays that allows for a strongly improved performance of sodium battery systems. Key is that a Li⁺ pre‐insertion in TiO₂ NTs can condition the SEI for Na⁺ replacement. SIBs constructed with Li‐pre‐inserted NTs deliver an exceptional Na⁺ cycling stability (e.g., 99.9 ± 0.1% capacity retention during 250 cycles at a current rate of 50 mA g^?1) and an excellent rate capability (e.g., 132 mA h g^?1 at a current rate of 1 A g^?1). The key factor in this outstanding performance is that Li‐pre‐insertion into TiO₂ NTs leads not only to an enhanced electronic conductivity in the tubes, but also expands the anatase lattice for facilitated subsequent Na⁺ cycling.     

Metal Sulfide‐Decorated Carbon Sponge as a Highly Efficient Electrocatalyst and Absorbant for Polysulfide in High‐Loading Li2S Batteries

Owing to its high theoretical specific capacity (1166 mA h g^?1) and particularly its advantage to be paired with a lithium‐metal‐free anode, lithium sulfide (Li₂S) is regarded as a much safer cathode for next‐generation advanced lithium–sulfur (Li–S) batteries. However, the low conductivity of Li₂S and particularly the severe “polysulfide shuttle” of lithium polysulfide (LiPS) dramatically hinder their practical application in Li–S batteries. To address such issues, herein a bifuctional 3D metal sulfide‐decorated carbon sponge (3DTSC), which is constructed by 1D carbon nanowires cross‐linked with 2D graphene nanosheets with high conductivity and polar 0D metal sulfide nanodots with efficient electrocatalytic activity and strong chemical adsorption capability for LiPSs, is presented. Benefiting from the well‐designed multiscale, multidimensional 3D porous nanoarchitecture with high conductivity, and efficient electrocatalytic and absorption ability, the 3DTSC significantly mitigates LiPS shuttle, improves the utilization of Li₂S, and facilitates the transport of electrons and ions. As a result, even with a high Li₂S loading of 8 mg cm^?2, the freestanding 3DTSC‐Li₂S cathode without a polymer binder and metallic current collector delivers outstanding electrochemical performance with a high areal capacity of 8.44 mA h cm^?2.     

Building Lithiophilic Ion‐Conduction Highways on Garnet‐Type Solid‐State Li+ Conductors

The integration of highly conductive solid‐state electrolytes (SSEs) into solid‐state cells is still a challenge mainly due to the high impedance existing at the electrolyte/electrode interface. Although solid‐state garnet‐based batteries have been successfully assembled with the assistance of an intermediate layer between the garnet and the Li metal anode, the slow discharging/charging rates of the batteries inhibits practical applications, which require much higher power densities. Here, a crystalline sulfonated‐covalent organic framework (COF) thin layer is grown on the garnet surface via a simple solution process. It not only significantly improves the lithiophilicity of garnet electrolytes via the lithiation of the COF layer with molten Li, but also creates effective Li⁺ diffusion “highways” between the garnet and the Li metal anode. As a result, the interfacial impedance of symmetric solid‐state Li cells is significantly decreased and the cells can be operated at high current densities up to 3 mA cm^?2, which is difficult to achieve with current interfacial modification technologies for SSEs. The solid‐state Li‐ion batteries using LiFePO₄ cathodes, Li anodes, and COF‐modified garnet electrolytes thus exhibit a significantly improved rate capability.     

Sodium Plating from Na‐β″‐Alumina Ceramics at Room Temperature,Paving the Way for Fast‐Charging All‐Solid‐State Batteries

All‐solid‐state batteries with an alkali metal anode have the potential to achieve high energy density. However, the onset of dendrite formation limits the maximum plating current density across the solid electrolyte and prevents fast charging. It is shown that the maximum plating current density is related to the interfacial resistance between the solid electrolyte and the metal anode. Due to their high ionic conductivity, low electronic conductivity, and stability against sodium metal, Na‐β″‐alumina ceramics are excellent candidates as electrolytes for room‐temperature all‐solid‐state batteries. Here, it is demonstrated that a heat treatment of Na‐β″‐alumina ceramics in argon atmosphere enables an interfacial resistance <10 Ω cm² and current densities up to 12 mA cm^?2 at room temperature. The current density obtained for Na‐β″‐alumina is ten times higher than that measured on a garnet‐type Li₇La₃Zr₂O₁₂ electrolyte under equivalent conditions. X‐ray photoelectron spectroscopy shows that eliminating hydroxyl groups and carbon contaminations at the interface between Na‐β″‐alumina and sodium metal is key to reach such values. By comparing the temperature‐dependent stripping/plating behavior of Na‐β″‐alumina and Li₇La₃Zr₂O₁₂, the role of the alkali metal in governing interface kinetics is discussed. This study provides new insights into dendrite formation and paves the way for fast‐charging all‐solid‐state batteries.     

A Hybrid Mg2+/Li+ Battery Based on Interlayer‐Expanded MoS2/Graphene Cathode

The hybrid Mg²⁺/Li⁺ battery (MLIB) is a very promising energy storage technology that combines the advantage of the Li and Mg electrochemistry. However, previous research has shown that the battery performance is limited due to the strong dependence on the Li content in the dual Mg²⁺/Li⁺ electrolyte. This limitation can be circumvented by significantly improving the diffusion kinetics of Mg²⁺ in the electrode, so that both Li⁺ and Mg²⁺ ions can be utilized as charge carriers. Herein, a free‐standing interlayer expanded MoS₂/graphene composite (E‐MG) is demonstrated as a cathode for MLIB. The key advantage of this cathode is to enable the efficient intercalation of both Mg²⁺ and Li⁺. The E‐MG electrode displays a reversible capacity of ≈300 mA h g^?1 at 20 mA g^?1 in an MLIB cell, corresponding to a specific energy density up to ≈316.9 W h kg^?1, which is comparable to that of the state‐of‐the‐art Li‐ion batteries (LIBs) and has no dendrite formation. The composite electrode is stable against cycling with a coulombic efficiency close to 100% at 500 mA g^?1. This new electrode design represents a significant step forward for building a safe and high‐density electrochemical energy storage system.     

A Versatile Sn‐Substituted Argyrodite Sulfide Electrolyte for All‐Solid‐State Li Metal Batteries

Sulfide‐based solid‐state electrolytes (SSEs) for all‐solid‐state Li metal batteries (ASSLMBs) are attracting significant attention due to their high ionic conductivity, inherently soft properties, and decent mechanical strength. However, the poor incompatibility with Li metal and air sensitivity have hindered their application. Herein, the Sn (IV) substitution for P (V) in argyrodite sulfide Li₆PS₅I (LPSI) SSEs is reported, in the preparation of novel LPSI‐xSn SSEs (where x is the Sn substitution percentage). Appropriate aliovalent element substitutions with larger atomic radius (R_<Sn> > R_<P>) provides the optimized LPSI‐20Sn electrolyte with a 125 times higher ionic conductivity compared to that of the LPSI electrolyte. The high ionic conductivity of LPSI‐20Sn enables the rich I‐containing electrolyte to serve as a stabilized interlayer against Li metal in sulfide‐based ASSLMBs with outstanding cycling stability and rate capability. Most importantly, benefiting from the strong Sn–S bonding in Sn‐substituted electrolytes, the LPSI‐20Sn electrolyte shows excellent structural stability and improved air stability after exposure to O₂ and moisture. The versatile Sn substitution in argyrodite LPSI electrolytes is believed to provide a new and effective strategy to achieve Li metal‐compatible and air‐stable sulfide‐based SSEs for large‐scale applications.     

Facilitating Interfacial Stability Via Bilayer Heterostructure Solid Electrolyte Toward High‐energy,Safe and Adaptable Lithium Batteries

Solid‐state electrolytes are widely anticipated to enable the revival of high energy density and safe metallic Li batteries, however, their lower ionic conductivity at room temperature, stiff interfacial contact, and severe polarization during cycling continue to pose challenges in practical applications. Herein, a dual‐composite concept is applied to the design of a bilayer heterostructure solid electrolyte composed of Li⁺ conductive garnet nanowires (Li_6.75La₃Zr_1.75Nb_0.25O₁₂)/polyvinylidene fluoride‐co‐hexafluoropropylene (PVDF‐HFP) as a tough matrix and modified metal organic framework particles/polyethylene oxide/PVDF‐HFP as an interfacial gel. The integral ionic conductivity of the solid electrolyte reaches 2.0 × 10^?4 S cm^?1 at room temperature. In addition, a chemically/electrochemically stable interface is rapidly formed, and Li dendrites are well restrained by a robust inorganic shield and matrix. As a result, steady Li plating/stripping for more than 1700 h at 0.25 mA cm^?2 is achieved. Solid‐state batteries using this bilayer heterostructure solid electrolyte deliver promising battery performance (efficient capacity output and cycling stability) at ambient temperature (25 °C). Moreover, the pouch cells exhibit considerable flexibility in service and unexpected endurance under a series of extreme abuse tests including hitting with a nail, burning, immersion under water, and freezing in liquid nitrogen.