A Multisite Strategy for Enhancing the Hydrogen Evolution Reaction on a Nano‐Pd Surface in Alkaline Media

The hydrogen evolution reaction (HER) on a noble metal surface in alkaline media is more sluggish than that in acidic media due to the limited proton supply. To promote the reaction, it is necessary to transform the alkaline HER mechanism via a multisite catalyst, which has additional water dissociation sites to improve the proton supply to an optimal level. Here, this study reports a top‐down strategy to create a multisite HER catalyst on a nano‐Pd surface and how to further fine‐tune the areal ratio of the water dissociation component to the noble metal surface in core/shell‐structured nanoparticles (NPs). Starting with Pd/Fe₃O₄ core/shell NPs, electrochemical cycling is used to tune the coverage of iron (oxy)hydroxide on a Pd surface. The alkaline HER activity of the core/sell Pd/FeO_x (OH)_2?2x NPs exhibits a volcano‐shaped correlation with the surface Fe species coverage. This indicates an optimum coverage level where the rates of both the water dissociation step and the hydrogen formation step are balanced to achieve the highest efficiency. This multisite strategy assigns multiple reaction steps to different catalytic sites, and should also be extendable to other core/shell NPs to optimize their HER activity in alkaline media.     

Vertical CoP Nanoarray Wrapped by N,P‐Doped Carbon for Hydrogen Evolution Reaction in Both Acidic and Alkaline Conditions

Hydrogen evolution reaction (HER) is a key reaction in water splitting, and developing efficient and robust non‐noble electrocatalysts for HER is still a great challenge for large‐scale hydrogen production. Herein, a vertically aligned core–shell structure grown on Ti foil with CoP nanoarray as a core and N,P‐doped carbon (NPC) as a shell (CoP/NPC/TF) is first reported as an efficient electrocatalyst for HER. Results indicate that CoP/NPC/TF only demands the overpotentials of 91 and 80 mV to drive the current density of 10 mA cm^?2 in acidic and alkaline solutions. The electrochemical measurements and theoretical calculations show that the synergy of CoP nanorod core and porous NPC shell enhances HER performance significantly, because the introduction of porous NPC shell not only offers more active sites but also improves the electrical conductivity and durability of the sample in acidic and alkaline solutions. Density functional theory calculation further reveals that all the C atoms between N and P atoms in CoP/NPC are the most efficient active sites, which greatly improve the HER performance. The identification of active species in this work provides an effective strategy to design and synthesize the low‐cost, high‐efficient, and robust CoP‐based electrocatalysts.     

Ultralow Ru Loading Transition Metal Phosphides as High‐Efficient Bifunctional Electrocatalyst for a Solar‐to‐Hydrogen Generation System

Water splitting is a promising technology for sustainable conversion of hydrogen energy. The rational design of oxygen evolution reaction (OER) and hydrogen evolution reaction (HER) bifunctional electrocatalysts with superior activity and stability in the same electrolyte is the key to promoting their large‐scale applications. Herein, an ultralow Ru (1.08 wt%) transition metal phosphide on nickel foam (Ru–MnFeP/NF) derived from Prussian blue analogue, that effectively drivies both the OER and the HER in 1 m KOH, is reported. To reach 20 mA cm^?2 for OER and 10 mA cm^?2 for HER, the Ru–MnFeP/NF electrode only requires overpotentials of 191 and 35 mV, respectively. Such high electrocatalytic activity exceeds most transition metal phosphides for the OER and the HER, and even reaches Pt‐like HER electrocatalytic levels. Accordingly, it significantly accelerates full water splitting at 10 mA cm^?2 with 1.470 V, which outperforms that of the integrated RuO₂ and Pt/C couple electrode (1.560 V). In addition, the extremely long operational stability (50 h) and the successful demonstration of a solar‐to‐hydrogen generation system through full water splitting provide more flexibility for large‐scale applications of Ru–MnFeP/NF catalysts.     

Microwave‐Induced Metal Dissolution Synthesis of Core–Shell Copper Nanowires/ZnS for Visible Light Photocatalytic H2 Evolution

A microwave‐induced metal dissolution strategy is developed for in situ synthesis of copper nanowires/ZnS (CuNWs/ZnS) hybrids with core–shell structure. The CuNWs are used as microwave antennas to create local “super‐hot” surfaces to further initiate ZnS crystallization with full coverage on CuNWs. With the help of S^2?, the hot metal surface further results in the CuNWs dissolution with promoted Cu⁺ diffusion and incorporation into the ZnS lattice. With the narrowed bandgap of ZnS and the strongly coupled interface between CuNWs and ZnS created by microwaves, the as‐prepared hybrid composites exhibit an enhanced activity and stability in visible light for the photocatalytic H₂ evolution. The corresponding H₂ evolution rate reaches up to 10722 µmol h^?1 g^?1 with apparent quantum efficiency (AQE) of 69% under 420 nm LED irradiation, showing a remarkably high AQE among the noble‐metal free visible light‐driven photocatalysts and demonstrating a promising potential in practical applications to deal with the energy crisis.     

Wrinkled Rh2P Nanosheets as Superior pH‐Universal Electrocatalysts for Hydrogen Evolution Catalysis

Searching for highly efficient and durable electrocatalysts for the hydrogen evolution reaction (HER) that function effectively at all pHs is of great interest to the scientific community, however it is still a grand challenge, because the HER kinetics of Pt in alkaline solutions are approximately two to three orders of magnitude lower than that in acidic solution. Herein, a new class of wrinkled, ultrathin Rh₂P nanosheets for enhancing HER catalysis at all pHs is reported. They exhibit a small overpotential of 18.3 mV at 10 mA cm^?2, low Tafel slope of 61.5 mV dec^?1, and good durability in alkaline media, much better than the commercial Pt/C catalyst. Density functional theory calculations reveal that the active open‐shell effect from the P‐3p band not only promotes Rh‐4d for increased proton–electron charge exchange but also provides excellent p–p overlapping to locate the O‐related species as distributary center, which can benefit the HER process in alkaline media. It is also demonstrated that the present wrinkled, ultrathin Rh₂P nanosheets are highly efficient and durable electrocatalysts toward HER in both acid and neutral electrolytes. The present work opens a new material design for ultrathin 2D metal phosphide nanostructures for the purpose of boosting HER performance at all pHs.     

Hierarchical Microcables Constructed by CoP@C⊂Carbon Framework Intertwined with Carbon Nanotubes for Efficient Lithium Storage

Transition‐metal phosphides (TMPs)‐based electrode materials with high capacity have attracted considerable interest as a promising anode material for lithium?ion batteries (LIBs). Herein, a hierarchical cable‐like structure composed of CoP@C core?shell nanoparticles (NPs) encapsulated in one‐dimensional (1D) porous carbon framework intertwined with N‐doped carbon nanotubes (CoP@C?PCF/NCNTs) is synthesized by a self‐templating, self‐catalytic, and subsequent vapor‐phase phosphorization strategy. The unique nanoarchitecture regime provides multiple advantages. The 1D carbon framework allows for quick ion and electron access, maintaining the integrity and accommodating the volume change of the structure during repeated discharging/charging. The internal carbon shell can prevent the direct aggregation of CoP NPs on cycling. The external NCNTs on the surface supply a staggered conductive network to promote electrolyte penetration and charge transportation. Impressively, the as‐fabricated hybrid nanocables deliver a reversible capacity of 712 mAh g^?1 at 0.5 A g^?1 for over 700 cycles with excellent rate capability as an anode material for LIBs. The significantly improved lithium storage properties of CoP@C?PCF/NCNTs reveal the importance of reasonable design and engineering of novel hierarchical structures with higher complexity.     

3D TiC/C Core/Shell Nanowire Skeleton for Dendrite‐Free and Long‐Life Lithium Metal Anode

Construction of stable dendrite‐free Li metal anode is crucial for the development of advanced Li–S and Li–air batteries. Herein, self‐supported TiC/C core/shell nanowire arrays as skeletons and confined hosts of molten Li forming integrated trilayer TiC/C/Li anode are described. The TiC/C core/shell nanowires with diameters of 400–500 nm exhibit merits of good lithiophilicity, high electrical conductivity, and abundant porosity. The as‐prepared TiC/C/Li anode exhibits prominent electrochemical performance with a small hysteresis of less than 85 mV beyond 200 cycles (3.0 mA cm^?2) as well as a very high Coulombic efficiency up to 98.5% for 100 cycles at 1.0 mA cm^?2. When the structured anode is coupled with lithium iron phosphate or sulfur cathode, the assembled full cells with trilayer TiC/C/Li anodes display enhanced capability retention and improved Coulombic efficiency. This is ascribed to the unique TiC/C matrix, which can not only provide interspace for accommodating “hostless” Li, but also afford interconnected rapid transfer paths for electrons and ions with low local current densities, leading to effective inhabitation growth of Li dendrites and lower interfacial resistance. A fresh way for construction of advanced stable Li metal anodes is provided in this work.     

A Stable Graphitic,Nanocarbon‐Encapsulated,Cobalt‐Rich Core–Shell Electrocatalyst as an Oxygen Electrode in a Water Electrolyzer

The oxygen electrode plays a vital role in the successful commercialization of renewable energy technologies, such as fuel cells and water electrolyzers. In this study, the Prussian blue analogue‐derived nitrogen‐doped nanocarbon (NC) layer‐trapped, cobalt‐rich, core–shell nanostructured electrocatalysts (core–shell Co@NC) are reported. The electrode exhibits an improved oxygen evolution activity and stability compared to that of the commercial noble electrodes. The core–shell Co@NC‐loaded nickel foam exhibits a lower overpotential of 330 mV than that of IrO₂ on nickel foam at 10 mA cm^?2 and has a durability of over 400 h. The commercial Pt/C cathode‐assisted, core–shell Co@NC–anode water electrolyzer delivers 10 mA cm^?2 at a cell voltage of 1.59 V, which is 70 mV lower than that of the IrO₂–anode water electrolyzer. Over the long‐term chronopotentiometry durability testing, the IrO₂–anode water electrolyzer shows a cell voltage loss of 230 mV (14%) at 95 h, but the loss of the core–shell Co@NC–anode electrolyzer is only 60 mV (4%) even after 350 h cell‐operation. The findings indicate that the Prussian blue analogue is a class of inorganic nanoporous materials that can be used to derive metal‐rich, core–shell electrocatalysts with enriched active centers.     

One‐Step Controllable Synthesis of Catalytic Ni4Mo/MoOx/Cu Nanointerfaces for Highly Efficient Water Reduction

Currently, in addition to the electroactive non‐noble metal water‐splitting electrocatalysts, a scalable synthetic route and simple activity enhancement strategy is also urgently needed. In particular, the well‐controlled synthesis of the well‐recognized metal–metal nanointer face in a single step remains a key challenge. Here, the synthesis of Cu‐supported Ni₄Mo nanodots on MoO_x nanosheets (Ni₄Mo/MoO_x) with controllable Ni₄Mo particle size and d‐band structure is reported via a facile one‐step electrodeposition process. Density functional theory (DFT) calculations reveal that the active open‐shell effect from Ni‐3d‐band optimizes the electronic configuration. The Cu‐substrate enables the surface Ni–Mo alloy dots to be more electron‐rich, forming a local connected electron‐rich network, which boosts the charge transfer for effective binding of O‐related species and proton–electron charge exchange in the hydrogen evolution reaction. The Cu‐supported Ni₄Mo/MoO_x shows an ultralow overpotential of 16 mV at a current density of 10 mA cm^?2 in 1 m KOH, demonstrating the smallest overpotential, at loadings as low as 0.27 mg cm^?2, among all non‐noble metal catalysts reported to date. Moreover, an overpotential of 105 mV allows it to achieve a current density of 250 mA cm^?2 in 70 °C 30% KOH, a remarkable performance for alkaline hydrogen evolution with competitive potential for applications.     

Oriented Transformation of Co‐LDH into 2D/3D ZIF‐67 to Achieve Co–N–C Hybrids for Efficient Overall Water Splitting

Construction of well‐defined metal–organic framework precursor is vital to derive highly efficient transition metal–carbon‐based electrocatalyst for hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) in water splitting. Herein, a novel strategy involving an in situ transformation of ultrathin cobalt layered double hydroxide into 2D cobalt zeolitic imidazolate framework (ZIF‐67) nanosheets grafted with 3D ZIF‐67 polyhedra supported on the surface of carbon cloth (2D/3D ZIF‐67@CC) precursor is proposed. After a low‐temperature pyrolysis, this precursor can be further converted into hybrid composites composed of ultrafine cobalt nanoparticles embedded within 2D N‐doped carbon nanosheets and 3D N‐doped hollow carbon polyhedra (Co@N‐CS/N‐HCP@CC). Experimental and density functional theory calculations results indicate that such composites have the advantages of a large number of accessible active sites, accelerated charge/mass transfer ability, the synergistic effect of components as well as an optimal water adsorption energy change. As a result, the obtained Co@N‐CS/N‐HCP@CC catalyst requires overpotentials of only 66 and 248 mV to reach a current density of 10 mA cm^?2 for HER and OER in 1.0 m KOH, respectively. Remarkably, it enables an alkali‐electrolyzer with a current density of 10 mA cm^?2 at a low cell voltage of 1.545 V, superior to that of the IrO₂@CC||Pt/C@CC couple (1.592 V).     

Understanding Ostwald Ripening and Surface Charging Effects in Solvothermally‐Prepared Metal Oxide–Carbon Anodes for High Performance Rechargeable Batteries

Metal oxides synthesized by the solvothermal approach have widespread applications, while their nanostructure control remains challenging because their reaction mechanism is still not fully understood. Herein, it is demonstrated how the competitive relation between Ostwald ripening and surface charging during solvothermal synthesis is crucial to engineering high‐quality metal (oxide)–carbon nanomaterials. Using SnO₂ as a case study, a new type of hollow SnO₂–C hybrid nanoparticles is synthesized consisting of core–shell structured SnO₂@C nanodots (which has not been previously reported). This new anode material exhibits extremely high lithium storage capacity of 1225 and 955 mAh g^?1 at 200 and 500 mA g^?1, respectively, and excellent cycling stability. In addition, full‐battery cells are constructed combining SnO₂–C anode with Ni‐rich cathode, which can be charged to a higher voltage compared to commercial graphite anode and still demonstrate extraordinary rate performance. This study provides significant insight into the largely unexplored reaction mechanism during solvothermal synthesis, and demonstrates how such understanding can be used to achieve high‐performance metal (oxide)–C anodes for rechargeable batteries.     

Bifunctional Conducting Polymer Coated CoP Core–Shell Nanowires on Carbon Paper as a Free‐Standing Anode for Sodium Ion Batteries

This study proposes a conformal surface coating of conducting polymer for protecting 1D nanostructured electrode material, thereby enabling a free‐standing electrode without binder for sodium ion batteries. Here, polypyrrole (PPy), which is one of the representative conducting polymers, encapsulated cobalt phosphide (CoP) nanowires (NWs) grown on carbon paper (CP), finally realizes 1D core–shell CoP@PPy NWs/CP. The CoP core is connected to the PPy shell via strong chemical bonding, which can maintain a Co–PPy framework during charge/discharge. It also possesses bifunctional features that enhances the charge transfer and buffers the volume expansion. Consequently, 1D core–shell CoP@PPy NWs/CP demonstrates superb electrochemical performance, delivering a high areal capacity of 0.521 mA h cm^?2 at 0.15 mA cm^?2 after 100 cycles, and 0.443 mA h cm^?2 at 1.5 mA cm^?2 even after 1000 cycles. Even at a high current density of 3 mA cm^?2, a significant areal discharge capacity reaching 0.285 mA h cm^?2 is still maintained. The outstanding performance of the CoP@PPy NWs/CP free‐standing anode provides not only a novel insight into the modulated volume expansion of anode materials but also one of the most effective strategies for binder‐free and free‐standing electrodes with decent mechanical endurance for future secondary batteries.     

Apically Dominant Mechanism for Improving Catalytic Activities of N‐Doped Carbon Nanotube Arrays in Rechargeable Zinc–Air Battery

The oxygen reduction reaction (ORR) and the oxygen evolution reaction (OER) in zinc–air batteries (ZABs) require highly efficient, cost‐effective, and stable electrocatalysts as alternatives to high cost and low poison resistant platinum group metals (PGM) catalysts. Although nitrogen‐doped carbon nanotube (NCNT) arrays are now capable of catalyzing ORR efficiently, their hydrophobic surface and base‐growth mode are found to limit the catalytic performance in the practical ZABs. Here, the concept of an apically dominant mechanism in improving the catalytic performance of NCNT by precisely encapsulating CoNi nanoparticles (NPs) within the apical domain of NCNT on the Ni foam (denoted as CoNi@NCNT/NF) is demonstrated. The CoNi@NCNT/NF exhibits a more excellent catalytic performance toward both ORR and OER than that of traditional NCNT derived from the base‐growth method. The ZAB coin cell using CoNi@NCNT/NF as an air electrode shows a peak power density of 127 mW cm^?2 with an energy density of 845 Wh kg_Zn^?1 and rechargeability over 90 h, which outperforms the performance of PGM catalysts. Density functional theory calculations reveal that the ORR catalytic performance of the CoNi@NCNT/NF is mainly attributed to the synergetic contributions from NCNT and the apical active sites on NCNT near to CoNi NPs.     

Optical and structural characterization of CdS/ZnS and CdS:Cu2+/ZnS core–shell nanoparticles

Core‐shell CdS/ZnS (Zn 0.025?0.125 M) and CdS:Cu²⁺(1%)/ZnS nanoparticles were successfully synthesized using a chemical method. X‐ray diffraction (XRD), high‐resolution transmission electron microscopy (HR TEM), photoluminescence (PL) and UV/Visible (UV/Vis) techniques were used to characterize the novel CdS/ZnS and CdS:Cu²⁺/ZnS core–shell nanoparticles. All absorption peaks of the synthesized samples were highly blue‐shifted from the bulk CdS and ZnS. Very narrow and symmetric PL emission was observed in the yellow region for core–shell CdS/ZnS. Furthermore, the PL emission of CdS/ZnS was tuned into orange region by incorporate the Cu ion into the core CdS lattice. Copyright © 2013 John Wiley & Sons, Ltd.     

Boronization‐Induced Ultrathin 2D Nanosheets with Abundant Crystalline–Amorphous Phase Boundary Supported on Nickel Foam toward Efficient Water Splitting

The conversion of crystalline metal–organic frameworks (MOFs) into metal compounds/carbon hybrid nanocomposites via pyrolysis provides a promising solution to design electrocatalysts for electrochemical water splitting. However, pyrolyzing MOFs generally involves a complex high‐temperature treatment, which can destroy the coordinated surroundings within MOFs, and as a result not taking their full advantage of their electrolysis properties. Herein, a simple and room‐temperature boronization strategy is developed to convert nickel zeolite imidazolate framework (Ni‐ZIF) nanorods into ultrathin Ni‐ZIF/Ni? B nanosheets with abundant crystalline–amorphous phase boundaries. The combined experiment, and theoretical calculation results disclose that the ultrathin thickness allows fast electron transfer and ensures increased exposure of surface coordinatively unsaturated active sites while the crystalline–amorphous interface elaborately changes the potential‐determining step to energetically favorable intermediates. As a result, Ni‐ZIF/Ni? B nanosheets supported on nickel foam (NF) require overpotentials of 67 mV for the hydrogen evolution reaction and 234 mV for the oxygen evolution reaction to achieve a current density of 10 mA cm^?2. Remarkably, Ni‐ZIF/Ni? B@NF as a bifunctional electrocatalyst for overall water splitting enables an alkaline electrolyzer with 10 mA cm^?2 at an ultralow cell voltage of 1.54 V. The present work may open a new avenue to the design of MOF‐derived composites for electrocatalysis.     

Doped‐MoSe2 Nanoflakes/3d Metal Oxide–Hydr(Oxy)Oxides Hybrid Catalysts for pH‐Universal Electrochemical Hydrogen Evolution Reaction

Clean hydrogen production is highly promising to meet future global energy demands. The design of earth‐abundant materials with both high activity for hydrogen evolution reaction (HER) and electrochemical stability in both acidic and alkaline environments is needed, in order to enable practical applications. Here, the authors report a non‐noble 3d metal Cl‐chemical doping of liquid phase exfoliated single‐/few‐layer flakes of MoSe₂ for creating MoSe₂/3d metal oxide–hydr(oxy)oxide hybrid HER‐catalysts. It is proposed that the electron‐transfer from MoSe₂ nanoflakes to metal cations and the chlorine complexation‐induced neutralization, as well as the in situ formation of metal oxide–hydr(oxy)oxides on the MoSe₂ nanoflakes' surface, tailor the proton affinity of the catalysts, increasing the number and HER‐kinetics of their active sites in both acidic and alkaline electrolytes. The electrochemical coupling between doped‐MoSe₂/metal oxide–hydr(oxy)oxide hybrids and single‐walled carbon nanotubes heterostructures further accelerates the HER process. Lastly, monolithic stacking of multiple heterostructures is reported as a facile electrode assembly strategy to achieve overpotential for a cathodic current density of 10 mA cm^?2 of 0.081 and 0.064 V in 0.5 m H₂SO₄ and 1 m KOH, respectively. This opens up new opportunities to address the current density versus overpotential requirements targeted in pH‐universal hydrogen production.     

Ultrafine Metal Nanoparticles/N‐Doped Porous Carbon Hybrids Coated on Carbon Fibers as Flexible and Binder‐Free Water Splitting Catalysts

By employing in situ reduction of metal precursor and metal‐assisted carbon etching process, this study achieves a series of ultrafine transition metal‐based nanoparticles (Ni–Fe, Ni–Mo) embedded in N‐doped carbon, which are found efficient catalysts for electrolytic water splitting. The as‐prepared hybrid materials demonstrate outstanding catalytic activities as non‐noble metal electrodes rendered by the synergistic effect of bimetal elements and N‐dopants, the improved electrical conductivity, and hydrophilism. Ni/Mo₂C@N‐doped porous carbon (NiMo‐polyvinylpyrrolidone (PVP)) and NiFe@N‐doped carbon (NiFe‐PVP) produce low overpotentials of 130 and 297 mV at a current density of 10 mA cm^?2 as catalysts for hydrogen evolution reaction and oxygen evolution reaction, respectively. In addition, these binder‐free electrodes show long‐term stability. Overall water splitting is also demonstrated based on the couple of NiMo‐PVP||NiFe‐PVP catalyzer. This represents a simple and effective synthesis method toward a new type of nanometal–carbon hybrid electrodes.     

Near‐Infrared,Heavy Metal‐Free Colloidal “Giant” Core/Shell Quantum Dots

“Giant” core/shell quantum dots (g‐QDs) are a promising class of materials for future optoelectronic technologies due to their superior chemical‐ and photostability compared to bare QDs and core/thin shell QDs. However, inadequate light absorption in the visible and near‐infrared (NIR) region and frequent use of toxic heavy metals (e.g., Cd and Pb) are still major challenges for most g‐QDs (e.g., CdSe/CdS) synthesized to date. The synthesis of NIR, heavy metal‐free, Zn‐treated spherical CuInSe₂/CuInS₂ g‐QDs is reported using the sequential cation exchange method. These g‐QDs exhibit tunable NIR optical absorption and photoluminescence (PL) properties. Transient fluorescence spectroscopy shows prolonged lifetime with increasing shell thickness, indicating the formation of quasi type‐II band alignment, which is further confirmed by simulations. As a proof‐of‐concept, as‐synthesized g‐QDs are used to sensitize TiO₂ as a photoanode in a photoelectrochemical (PEC) cell, demonstrating an efficient and stable PEC system. These results pave the way toward synthesizing NIR heavy metal‐free g‐QDs, which are very promising components of future optoelectronic technologies.     

Trifunctional Electrocatalysis on Dual‐Doped Graphene Nanorings–Integrated Boxes for Efficient Water Splitting and Zn–Air Batteries

Despite the exciting achievements made in synthesis of monofunctional electrocatalysts for oxygen reduction reaction (ORR), oxygen evolution reaction (OER), or hydrogen evolution reaction (HER), it is challenging to develop trifunctional electrocatalysts for both ORR/OER/HER. Herein, N, O‐codoped graphene nanorings‐integrated boxes (denoted NOGB) are crafted via high‐temperature pyrolysis and following acid etching of hybrid precursors containing polymers and Prussian blue analogue cubes. The electrochemical results signified that the resulting NOGB‐800 (800 refers to pyrolysis temperature) is highly active for trifunctional electrocatalysis of ORR/OER/HER. This can be reasonably attributed to the advanced nanostructures (i.e., the hierarchically porous nanostructures on the hollow nanorings) and unique chemical compositions (i.e., N, O‐codoped graphene). More attractively, the rechargeable Zn–air battery based on NOGB‐800 displays maximum power density of 111.9 mW cm^?2 with small charge–discharge potential of 0.72 V and excellent stability of 30 h, comparable with the Pt/C+Ir/C counterpart. The NOGB‐800 could also be utilized as bifunctional electrocatalysts for overall water splitting to yield current density of 10 mA cm^?2 at a voltage of 1.65 V, surpassing most reported electrocatalysts. Therefore, the NOGB‐800 is a promising candidate instead of precious metal–based electrocatalysts for the efficient Zn–air battery and water splitting.     

Yolk–Shell NiS2 Nanoparticle‐Embedded Carbon Fibers for Flexible Fiber‐Shaped Sodium Battery

Fiber‐shaped rechargeable batteries hold promise as the next‐generation energy storage devices for wearable electronics. However, their application is severely hindered by the difficulty in fabrication of robust fiber‐like electrodes with promising electrochemical performance. Herein, yolk–shell NiS₂ nanoparticles embedded in porous carbon fibers (NiS₂?PCF) are successfully fabricated and developed as high‐performance fiber electrodes for sodium storage. Benefiting from the robust embedded structure, 3D porous and conductive carbon network, and yolk–shell NiS₂ nanoparticles, the as‐prepared NiS₂?PCF fiber electrode achieves a high reversible capacity of about 679 mA h g^?1 at 0.1 C, outstanding rate capability (245 mA h g^?1 at 10 C), and ultrastable cycle performance with 76% capacity retention over 5000 cycles at 5 C. Notably, a flexible fiber‐shaped sodium battery is assembled, and high reversible capacity is kept at different bending states. This work offers a new electrode‐design paradigm toward novel carbon fiber electrodes embedded with transition metal oxides/sulfides/phosphides for application in flexible energy storage devices.