Rotary drum composting of vegetable waste and tree leaves

High rate composting studies on institutional waste, i.e. vegetable wastes, tree leaves, etc., were conducted on a demonstration-scale (3.5 m³) rotary drum composter by evaluating changes in some physico-chemical and biological parameters. During composting, higher temperature (60–70 °C) at inlet zone and (50–60 °C) at middle zone were achieved which resulted in high degradation in the drum. As a result, all parameters including TOC, C/N ratio, CO₂ evolution and coliforms were decreased significantly within few days of composting. Within a week period, quality compost with total nitrogen (2.6%) and final total phosphorus (6 g/kg) was achieved; but relatively higher final values of fecal coliforms and CO₂ evolution, suggested further maturation. Thus, two conventional composting methods namely windrow (M1) and vermicomposting (M2) tried for maturation of primary stabilized compost. By examining these methods, it was suggested that M2 was found suitable in delivering fine grained, better quality matured compost within 20 days of maturation period.     

Co-composting of sewage sludge:fats mixtures and characteristics of the lipases involved

Co-composting of sewage sludge and animal fat mixtures was studied in order to determine the possibility of using this technology to recycle fat-enriched wastes. A maximum fat content of 30% in fat:sludge mixtures is recommended to achieve the international sanitation requirements on compost quality and to avoid an excessive thermophilic composting time. Under these conditions a fat content reduction of 85% was achieved. Biological activity was highly dependent on the moisture content as shown by the respiratory quotient values. Moisture content is a critical control factor because of the hydrophobic nature of fats and should be maintained above 40% in the composting of fats. Biological indices of the compost obtained after 69 days of process (maturity grade: IV; respiration index: 1.1 mg O₂ g OM⁻¹ h⁻¹) indicated a high stability and maturity degree of the material. Lipases responsible for fat hydrolysis were monitored during the composting process and a sample from the thermophilic period was characterized in terms of stability in front of pH and temperature. Optimal conditions for lipase stability were found at 38.3 °C and pH 7.97, however, the maximum lipolytic activity was observed at thermophilic temperatures. Lipases from the thermophilic period were purified by anion exchange chromatography and visualised by SDS-PAGE. Two major bands were observed at molecular weights of 29 and 62 kDa. These bands could not be identified precisely by N-terminal sequence analysis.     

Effect of feed to inoculum ratios on biogas yields of food and green wastes

Biogas and methane yields of food and green wastes and their mixture were determined using batch anaerobic digesters at mesophilic (35 ± 2 °C) and thermophilic (50 ± 2 °C) temperatures. The mixture was composed of 50% food waste and 50% green waste, based on the volatile solids (VS) initially added to the reactors. The thermophilic digestion tests were performed with four different feed to inoculum (F/I) ratios (i.e., 1.6, 3.1, 4.0 and 5.0) and the mesophilic digestion was conducted at one F/I (3.1). The results showed that the F/I significantly affected the biogas production rate. At four F/Is tested, after 25 days of thermophilic digestion, the biogas yield was determined to be 778, 742, 784 and 396 mL/g VS for food waste, respectively; 631, 529, 524 and 407 mL/g VS for green waste, respectively; and 716, 613, 671 and 555 mL/g VS for the mixture, respectively. About 80% of the biogas production was obtained during the first 10 days of digestion. At the F/I of 3.1, the biogas and methane yields from mesophilic digestion of food waste, green waste and their mixture were lower than the yields obtained at thermophilic temperature. The biogas yields were 430, 372 and 358 mL/g VS, respectively, and the methane yields were 245, 206, and 185 mL/g VS, respectively.     

Biodegradation of olive husk mixed with other agricultural wastes

In this study, the evolution of the most important parameters (temperature, pH, electrical conductivity, total organic carbon, total nitrogen, and C/N ratio) describing the composting process of olive oil husk with other organic wastes was investigated. Four windrows for obtaining two mixed wastes composts (MWCs) and two green wastes composts (GWCs) were prepared.     

Monitoring of green waste composting process based on redox potential

Among compostable matrices, green wastes represent a significant fraction which can be used as an amendment after composting. Several indicators, e.g. C(HA)/C(FA) or C/N ratios give information on evolution of the organic matrix during composting. However, measurement of these parameters is complex and requires laboratory conditions. The aim of this study was to propose on site easy-to-measure parameters to monitor composting process, such as redox potential (Eh), related to complex indices such as C(HA)/C(FA), C/N, A(210 nm)/A(280 nm), NH(4)(+)/NO(3)(-) ratios, and total organic matter (OM). Windrows were consisting in a mixture of green wastes such as palm, olive, cypress, pine, mimosa, and bay residues. By using covariance analysis, an opposite correlation between Eh and C(HA)/C(FA) ratio was found. Linear regression of this parameter with Eh was chosen to monitor the composting process. Therefore, Eh can be used to monitor green wastes composting.     

Chemical,microbial and physical properties of manufactured soils produced by co-composting municipal green waste with coal fly ash

Increasing proportions of coal fly ash were co-composted with municipal green waste to produce manufactured soil for landscaping use. Only the 100% green waste treatment reached a thermophilic composting phase (?50 °C) which lasted for 6 days. The 25% and 50% ash treatments reached 36–38 °C over the same period while little or no self-heating occurred in the 75% and 100% ash treatments. Composted green waste had a low bulk density and high total and macro-porosity. Addition of 25% ash to green waste resulted in a 75% increase in available water holding capacity. As the proportions of added ash in the composts increased, the organic C, soluble C, microbial biomass C, basal respiration and activities of β-glucosidase, L-asparaginase, alkali phosphatase and arylsulphatase enzymes in the composted products all decreased. It could be concluded that addition of fly ash to green waste at a proportion higher than 25% did not improve the quality parameters of manufactured soil.     

The kinetics of nicotine degradation,enzyme activities and genotoxic potential in the characterization of tobacco waste composting

This study aimed to determine nicotine biodegradation and the genotoxic potential of nicotine and its degradation products during the process of tobacco waste composting. Composting was carried out using two methods, i.e. the addition of 20% (bioreactor A) or 40% tobacco wastes to sewage sludge (bioreactor B) and control – sewage sludge (bioreactor C). Wheat straw was used as a structure-forming material. As a result of composting the contents of C and N in the bioreactors changed, the C:N ratio in bioreactor A changed from 22.8 to 13.00, and that in bioreactor B changed from 23.5 to 12.00. After composting, the biodegradation rate of nicotine was 78% in bioreactor A and 80% in bioreactor B, respectively. Using the Ames test it was shown that the composts produced did not exhibit mutagenicity.     

Ash in composting of source-separated catering waste

Our earlier experiments in small composters (220 l) indicated the favourable effect of ash from co-incineration of sorted dry waste on the composting of catering waste. The aim of this new study was to clarify further, at a scale of 10 m3, the feasibility of using similar ash as an additive in composting. Source-separated catering waste was mixed with bulking agent (peat and wood chips) and fuel ash from a small (4 MW) district heating power plant. Three compost mixes (CM) were obtained: CM I with 0%, CM II with 10% and CM III with 20 wt.% of fuel ash. These three different mixes were composted in a 10-m3 drum composter as three parallel experiments for 2 weeks each, from January to April 2000. After drum composting, masses were placed according to mixing proportions in separate curing piles. The catering waste fed to the drum was cold, sometimes icy. Even then the temperature rapidly increased to over 50 degrees C. In CM III, the temperature rose as high as 80 degrees C, and after the first week of composting the temperature was about 20 degrees C higher in the CMs II and III than in the CM I. It also improved the oxygen concentrations at the feeding end of the drum and obviously prevented the formation of H2S. No odour problems arose during the composting. Addition of ash increased the heavy metal contents of the composting masses, but the compost was suitable for cultivation or green area construction. Ash clearly decreased the loss of total nitrogen in a time span of 2 years. The lower amounts of nitrogen mean that the amounts applied per hectare can be greater than for normal composts. Measured by mineralization, the breaking down of the organic matter was more rapid in the CM III than in the CM I. Humic acid increased steadily during first 12 months composting, from the initial 39 mg/g organic matter to 115 and 137 mg/g in CMs II and III. Measured by temperature, mineralization and humification the addition of ash appeared to boost the composting. Ash had also other beneficial effects on composting it improved the availability of oxygen in compost mass during the drum composting phase and reduced the formation of odorous gases, especially H2S.     

一株分离自绿化废弃物堆肥枯草芽孢杆菌的常压室温等离子诱变及其发酵条件

【背景】为了提高堆肥降解有机废弃物的效率,高效堆肥菌剂成为了研究热点,其中以真菌应用的研究为多,但真菌也有对氧气和底物敏感等缺点,细菌对堆肥的作用开始被研究。本实验室以羧甲基纤维素钠(CMC-Na)为底物,从绿化废弃物堆肥中筛选得到枯草芽孢杆菌(Bacillussubtilis,B.subtilis) BL03,它具有较好的纤维素分解能力,能提高绿化废弃物堆肥中纤维素降解和腐殖质合成的速度。【目的】进一步提高B.subtilisBL03的纤维素酶生产能力。【方法】利用常压室温等离子(Atmospheric and room temperature plasma,ARTP)诱变BL03菌,通过CMC-刚果红固体培养基观察水解透明圈,以及液体发酵后检测酶活力的方法进行3轮筛选;通过连续多代培养观察突变株的遗传稳定性;通过梯度温度、p H培养研究突变株发酵的最适生长温度、培养基初始pH;利用正交设计方法研究适合突变株发酵培养的工业级原料配方。【结果】筛选到2株正突变株,酶活力分别提高了69%和72%;连续10代培养稳定,验证了突变株的遗传稳定性;其中酶活力最高的突变株BLA3890最适培养温度为37°C、培养基初始pH为5.0-6.5,研究得到较经济的发酵培养基配方。【结论】ARTP诱变B. subtilis BL03后得到的突变株BLA1973和BLA3890在绿化废弃物堆肥或其他纤维素降解行业具有进一步研究和应用的价值。     

Fungi of wheat and broad-bean straw composts II. Thermophilic fungi

Thirteen thermohilic genera and 19 species in addition to one variety of each of M. pulchella and H.grisea were collected from wheat and broad-bean straw composts at 45 °C. In wheat and broad-bean, all thermophilic fungi were completely checked between 4–9 days, and 1–8 days composting when the temperature ranged between 58 ° and 67 °C, and 58 ° and 70 °C respectively, and reappeared, represented by P. duponti, M. albomyces, T. lanuginosus and S. thermophile, after 9 or 10 days composting when the temperature decreased to 51.5 °–54 °C. Wheat and broad-bean straw composts were analyzed biochemically to follow the changes in ethanol and diastase soluble, hemicellulose, cellulose and lignin fractions during composting.     

Fungi of wheat and broad-bean straw composts

13 thermophilic genera and 19 species in addition to one variety of each of M. pulchella and H. grisea were collected from wheat and broad-bean straw composts at 45 °C. In wheat and broad-bean, all thermophilic fungi were completely checked between 4–9 days, and 1–8 days composting when the temperature ranged between 58° and 67 °C, and 58 ° and 70 °C respectively, and reappeared, represented by P. duponti, M. albomyces, T. lanuginosus and S. thermophile, after 9 or 10 days composting when the temperature decreased to 51.5° –54 ° C. Wheat and broad-bean straw composts were analysed biochemically to follow the changes in ethanol and diastase soluble, hemicellulose, cellulose and lignin fractions during composting.     

Improvement of phytase thermostability by using sorghum liquor wastes supplemented with starch

When a phytase solution, soluble starch, and sorghum liquor wastes were mixed at the ratio of 1:1:10 (v/w/w), the residual phytase activities after 30 min of treatment at 70 and 80 °C were respectively, about 90% and 18% of that at 37 °C. After 10 min treatment, the residual activity was 67% at 80 °C and 10% at 90 °C.     

Microbial community structure changes during bioremediation of PAHs in an aged coal-tar contaminated soil by in-vessel composting

The microbial community structure changes of an aged-coal-tar soil contaminated with polycyclic aromatic hydrocarbons (PAHs) were investigated during simulated bioremediation at the laboratory-scale using an in-vessel composting approach. The composting reactors were operated using a logistic three-factor factorial design with three temperatures (T=38, 55 or 70 °C), four soil to green-waste amendment ratios (S:GW=0.6:1, 0.7:1, 0.8:1 or 0.9:1 on a dry weight basis) and three moisture contents (MC=40%, 60% or 80%). Relative changes in microbial populations were investigated by following the dynamics of phospholipid fatty acid (PLFA) signatures using a ¹³C-labeled palmitic acid internal standard and sensitive GC/MS analysis during in-vessel composting over 98 days. The results of this investigation indicated that fungal to bacterial PLFA ratios were significantly influenced by temperature (p<0.05), and Gram-positive to Gram-negative bacterial ratios were significantly influenced by temperature (p<0.001) and S:GW ratio (p<0.01) during in-vessel composting. Additionally, the Gram-positive to Gram-negative bacterial ratios were correlated to the extent of PAH losses (p<0.005) at 70 °C.     

Microbiological analysis of composts produced on South Carolina poultry farms

Aims: The purpose of this study was to determine whether the methods used in compost operations of small and medium‐sized poultry forms resulted in the production of an amendment free of foodborne pathogens. Methods and Results: Nine compost heaps on five South Carolina poultry farms were surveyed at different stages of the composting process. Compost samples were analysed for coliforms and enriched for Escherichia coli O157:H7, Salmonella spp. and Listeria monocytogenes. The waste materials and composting practices differed among the surveyed farms. On two farms, new materials were added to heaps that had previously completed the active composting phase. Five compost heaps did not reach an internal temperature of 55°C, and c. 62% of all internal samples in the first composting phase contained moisture contents <40%. Escherichia coli was detected in 63% of the surface samples (n = 38) and 9·8% of the internal samples (n = 82) from the first composting phase, as compared with 16·7% of the surface samples (n = 12) and 0% internal samples (n = 24) from the second composting phase. Salmonella was detected in 26 and 6·1% of all surface and internal samples collected from heaps in the first composting phase, respectively, but was absent in all compost samples undergoing a second composting phase. The predominant Salmonella serotypes were Thompson, Montevideo and Anatum. Neither E. coli O157:H7 nor L. monocytogenes was detected in any of the samples. Conclusions: Our results indicate that the conditions at the compost surface are suitable for pathogen survival, and the complete composting process can result in the elimination of pathogens in poultry wastes. Significance and Impact of the Study: This research provides information regarding the effectiveness of the composting practices and microbiological quality of poultry compost produced by small‐ and medium‐sized farms. Ensuring the safety of compost that may be applied to soils should be an integral part of preharvest food safety programme.     

Variation in microbial population during composting of agro-industrial waste

Two compost piles were prepared, using two ventilation systems: forced ventilation and ventilation through mechanical turning. The material to compost was a mixture of orange waste, olive pomace, and grass clippings (2:1:1 v/v). During the composting period (375 days), samples were periodically taken from both piles, and the enumeration of fungi, actinomycetes, and heterotrophic bacteria was carried out. All studied microorganisms were incubated at 25 and 55 °C after inoculation in appropriate growth media. Fungi were dominant in the early stages of both composting processes; heterotrophic bacteria proliferated mainly during the thermophilic stage, and actinomycetes were more abundant in the final stage of the composting process. Our results showed that the physical and chemical parameters: temperature, pH, moisture, and aeration influenced the variation of the microbial population along the composting process. This study demonstrated that composting of these types of wastes, despite the prolonged mesophilic stage, provided an expected microbial variation.     

Continuous thermophilic composting (CTC) for rapid biodegradation and maturation of organic municipal solid waste

Fewer and fewer municipal solid wastes are treated by composting in China because of the disadvantages of enormous investment, long processing cycle and unstable products in a conventional composting treatment. In this study, a continuous thermophilic composting (CTC) method, only a thermophilic phase within the process, has been applied to four bench-scale composting runs, and further compared with a conventional composting run by assessing the indexes of pH, total organic carbon (TOC), total Kjeldahl nitrogen (TKN), C/N ratio, germination index (GI), specific oxygen uptake rate (SOUR), dissolved organic carbon (DOC) and dehydrogenase activity. After composting for 14 days, 16 days, 18 days and 19 days in the four CTC runs, respectively, mature compost products were obtained, with quality similar to or better than which had been stabilized for 28 days in run A. The products from the CTC runs also showed favorable stability in room temperature environment after the short-term composting at high temperature. The study suggested CTC as a novel method for rapid degradation and maturation of organic municipal solid wastes.     

Chemical and biological changes during composting of different organic wastes and assessment of compost maturity

Changes in organic C, total N, C:N ratio, activities of cellulase, xylanase and protease, and microbial population were determined during composting of different organic wastes such as mixture of sugarcane trash and cattle dung, press mud, poultry waste and water hyacinth biomass. There were losses of N in poultry waste and water hyacinth with the effect an initial increase in C:N ratio was observed which decreased later on due to decomposition. The activities of cellulase, xylanase and protease were maximum between 30 and 60 days of composting in various wastes. Similar trend was observed with respect to mesophilic bacterial and fungal population. Various quality parameters like C:N ratio, water soluble C (WSC), CO(2) evolution and level of humic substances were compared after 90 day composting. There was statistically significant correlation between C:N ratio and CO(2) evolution, WSC and humic substances. Significant correlation between CO(2) evolved and level of humic substances was also observed. The study shows that no single parameter can be taken as an index of compost maturity. However, C:N ratio and CO(2) evolved from finished compost can be taken as the most reliable indices of compost maturity.     

Changes in biochemical and microbiological parameters during the period of rapid composting of dairy manure with rice chaff

Various parameters were measured during the period of composting of dairy manure and rice chaff in different ratios (dairy manure/rice chaff=V/V, pile 1: 75/25; pile 2: 80/20; pile 3: 85/15) to evaluate their suitability as indicators for the composting process. The temperature in pile 1 increased rapidly and remained above 60 °C for 30 days, while the temperature in pile 3 increased slowly relative to the other two piles. Furthermore, the degradation of organic substrates, as indicated by the reduction of C/N ratio, was rapid in pile 1 (below 20% 28 days after beginning of the composting). The major fluctuations of various water-soluble fractions in all piles were observed during the first 3 weeks, and the results in general showed that the highest microbial populations and enzymatic activities also appeared in this phase. Various parameters indicated that the rapid composting method was a feasible one for treating agricultural wastes.     

Composting of waste from palm oil mill: a sustainable waste management practice

Malaysia is blessed with abundant natural resources and bears a favorable climate for commercial cultivation of crops such as oil palm. In Malaysia the total plantation area of oil palm was 4,487,957 ha in 2008. It has been reported that in 2005 there was a total of 423 palm oil mills having production capacity of approximately 89 million tonnes of fresh fruit bunch (FFB) per year. Waste from the oil palm mill process include palm oil mill effluent (POME), generated mainly from oil extraction, washing and cleaning up processes. POME contains cellulosic material, fat, oil, and grease. Discharging untreated effluent into water streams may cause considerable environmental problems. The solid wastes generated are mainly decanter cake, empty fruit bunches, seed shells and fibre from the mesocarp. POME as well as the solid wastes may rapidly deteriorate the surrounding environment if not dealt with properly. Hence there is an urgent need for a sustainable waste management system to tackle these wastes. As these wastes are organic in origin, they are rich in plant nutrients. Composting of waste generated from palm oil mills can be good practice as it will be helpful in recycling useful plant nutrients. This review deals with various aspects of waste management practices in palm oil mills and the possibility of composting the wastes.     

Fungal Communities Associated with the Biodegradation of Polyester Polyurethane Buried under Compost at Different Temperatures

Plastics play an essential role in the modern world due to their low cost and durability. However, accumulation of plastic waste in the environment causes wide-scale pollution with long-lasting effects, making plastic waste management expensive and problematic. Polyurethanes (PUs) are heteropolymers that made up ca. 7% of the total plastic production in Europe in 2011. Polyester PUs in particular have been extensively reported as susceptible to microbial biodegradation in the environment, particularly by fungi. In this study, we investigated the impact of composting on PUs, as composting is a microbially rich process that is increasingly being used for the processing of green waste and food waste as an economically viable alternative to landfill disposal. PU coupons were incubated for 12 weeks in fresh compost at 25°C, 45°C, and 50°C to emulate the thermophilic and maturation stages of the composting process. Incubation at all temperatures caused significant physical deterioration of the polyester PU coupons and was associated with extensive fungal colonization. Terminal restriction fragment length polymorphism (TRFLP) analysis and pyrosequencing of the fungal communities on the PU surface and in the surrounding compost revealed that the population on the surface of PU was different from the surrounding compost community, suggesting enrichment and selection. The most dominant fungi identified from the surfaces of PU coupons by pyrosequencing was Fusarium solani at 25°C, while at both 45°C and 50°C, Candida ethanolica was the dominant species. The results of this preliminary study suggest that the composting process has the potential to biodegrade PU waste if optimized further in the future.