Influence of self-assembled monolayer surface chemistry on Candida antarctica lipase B adsorption and specific activity

Immobilization of Candida antarctica B lipase was examined on gold surfaces modified with either methyl- or hydroxyl-terminated self-assembled alkylthiol monolayers (SAMs), representing hydrophobic and hydrophilic surfaces, respectively. Lipase adsorption was monitored gravimetrically using a quartz crystal microbalance. Lipase activity was determined colorimetrically by following p-nitrophenol propionate hydrolysis. Adsorbed lipase topography was examined by atomic force microscopy. The extent of lipase adsorption was nearly identical on either surface (approximately 240 ng cm⁻²), but its specific activity was sixfold higher on the methyl-terminated SAM, showing no activity loss upon immobilization. A uniform, 5.5 nm high, highly packed monolayer of CALB formed on the methyl-terminated SAM, while the adsorbed protein was disordered on the hydroxyl-terminated SAM. Hydrophobic surfaces thus may specifically orient the lipase in a highly active state.     

Enhancing performance of lipase immobilized on methyl-modified silica aerogels at the adsorption and catalysis processes: Effect of cosolvents

Hydrophobic silica aerogels modified with methyl group were applied as support to immobilize Candida rugosa lipase (CRL). At the adsorption process, different alcohols were used to intensify the immobilization of CRL. The results showed that n-butanol wetting the hydrophobic support prior to contacting with enzyme solution could promote lipase activity, but the adsorption quantity onto the support decreased. Based on this, a novel immobilization method was proposed: the support contacted with enzyme solution without any alcohols, and then the immobilized enzymes were activated by 90% (V) n-butanol solution. The experimental results showed that this method could keep high adsorption quantity (413.0 mg protein/g support) and increase the lipase specific activity by more than 50%. To improve the stability of immobilized lipase, the support after adsorption was contacted with n-octane to form an oil layer covering the immobilized lipases, thus the leakage can be decreased from over 30–4% within 24 h. By utilizing proper cosolvents, a high enzyme activity and loading capacity as well as little loss of lipase was achieved without covalent linkage between the lipase and the support. This is known to be an excellent result for immobilization achieved by physical adsorption only.     

Interfacial activation and bioimprinting of Candida rugosa lipase immobilized on polypropylene: effect on the enzymatic activity in solvent-free ethyl oleate synthesis

Lipase from Candida rugosa adsorbed on polypropylene powder (CR/PP) was subjected to activation pre-treatments in order to enhance its activity in solvent-free ethyl oleate synthesis. The lipase activation achieved upon adsorption onto a hydrophobic support like PP was further enhanced through oil–water interfacial activation and bioimprinting of the immobilized catalyst. Several aliphatic hydrocarbons/buffer pH 7 mixtures were used in the pre-activation of CR/PP with specific activity increments of up to 29%. Molecular bioimprinting was also performed, with specific activity enhancement of near 70% with respect to non-treated CR/PP. The effect of several fatty acids used as templates and the water present in the reaction medium was studied. The oil–water activation and bioimprinting treatments that led to the best activities were assayed at the immobilization step. Instead of pre-treating CR/PP adsorbed in buffer medium, interfacial activation with octane/buffer and bioimprinting with a mix of fatty acids were carried out in the immobilization vial. The best results were found for CR/PP immobilized in 5/95 octane/buffer (v/v, %) medium. In that way, a biocatalyst with enhanced specific activity is obtained right from the immobilization vial with no need of further activation steps prior to reaction.     

Hydrolases on silica surfaces: Coverage-activity–molecular property relationships revealed

A set of recommendations to maintain high activity of immobilized enzymes is developed based on direct observation via AFM. This helps to close knowledge gaps that often lead to poor performance of nanobiocatalysts for chemical synthesis. Molecule-level height and volume distribution analyses from high-resolution AFM images were applied to Candida antarctica Lipase B (CALB), subtilisin Carlsberg, and the Lipase from Thermomyces lanuginosus (TLL) deposited on model silica surfaces. Ensembles of flexible or “soft” enzymes appear separated when interactions with the surface are considerable at low surface coverage but form highly entangled structures of increased conformational stability at high surface coverage. By contrast, ensembles of rigid or “hard” enzymes appear to maintain stable aggregates even under strong interaction with the surface. The more rigid the enzyme the higher its tendency to remain in a densely packed state that is able to withstand surface-induced conformational transitions detrimental to catalysis. Weakening of surface-protein interactions for “soft” enzymes will prevent single-molecule immobilization, which reduces catalytic competency through structural changes. Multi-layer coverage in enzyme immobilization should generally be avoided due to mass transfer limitations.     

Immobilization of Candida antarctica lipase B (CALB) on surface-modified rice husk ashes (RHA) via physical adsorption and cross-linking methods

In the present study, the recovery of activity of Candida antarctica lipase B (CALB) immobilized onto surface-modified rice husk ash (RHA) was 90% for both cross-linking and adsorption methods. Both cross-linked and adsorbed immobilized preparations were very stable, retaining more than 48% of their activity over the range of temperatures studied. The optimum temperature and optimum pH values were 37?°C and 7.0, respectively for both immobilized preparations, while the relative activities after storage at 4.0?°C for 60 days were 55% and 65% using cross-linking and adsorption methods, respectively. Also, the activity of the immobilized lipase began to decrease after 10 cycles, more than 58% of the initial activities were still retained after 10 cycles for both immobilization methods. These results indicated that lipase immobilized by cross-linking and adsorption not only effected activity recovery, but also remarkably effected stability, reusability and application adaptability. It can be concluded that, surface-modified RHA can be used as alternative supports for immobilization of CALB for polymerization reactions.     

Improvement of the functional properties of a thermostable lipase from alcaligenes sp. via strong adsorption on hydrophobic supports

Lipase QL from Alcaligenes sp. is a quite thermostable enzyme. For example, it retains 75% of catalytic activity after incubation for 100 h at 55 °C and pH 7.0. Nevertheless, an improvement of the enzyme properties was intended via immobilization by covalent attachment to different activated supports and by adsorption on hydrophobic supports (octadecyl-sepabeads). This latter immobilization technique promotes the most interesting improvement of enzyme properties: (a) the enzyme is hyperactivated after immobilization: the immobilized preparation exhibits a 135% of catalytic activity for the hydrolysis of p-nitrophenyl propionate as compared to the soluble enzyme; (b) the thermal stability of the immobilized enzyme is highly improved: the immobilized preparation exhibits a half-life time of 12 h when incubated at 80 °C, pH 8.5 (a 25-fold stabilizing factor regarding to the soluble enzyme); (c) the optimal temperature was increased from 50 °C (soluble enzyme) up to 70 °C (hydrophobic support enzyme immobilized preparations); (d) the enantioselectivity of the enzyme for the hydrolysis of glycidyl butyrate and its dependence on the experimental conditions was significantly altered. Moreover, because the enzyme becomes reversibly but very strongly adsorbed on these highly hydrophobic supports, the lipase may be desorbed after its inactivation and the support may be reused. Very likely, adsorption occurs via interfacial activation of the lipase on the hydrophobic supports at very low ionic strength. On the other hand, all the covalent immobilization protocols used to immobilize the enzyme hardly improved the properties of the lipase.     

Solid-phase handling of hydrophobins: immobilized hydrophobins as a new tool to study lipases

Hydrophobins are fungal proteins that self-assemble spontaneously at hydrophilic-hydrophobic interfaces and change the polar nature of the surfaces to which they attach. This attribute can be used to introduce hydrophobic foci on the surface of hydrophilic supports where hydrophobins are attached by covalent binding. In this paper, we report the binding of Pleurotus ostreatus hydrophobins to a hydrophilic matrix (agarose) to construct a support for noncovalent immobilization and activation of lipases from Candida antarctica, Humicola lanuginosa, and Pseudomonas flourescens. Lipase immobilization on agarose-bound hydrophobins proceeded at very low ionic strength and resulted in increased lipase activity and stability. The enzyme could be desorbed from the support using moderate concentrations of Triton X-100, and its enantioselectivity was similar to that of lipases interfacially immobilized on conventional hydrophobic supports. These results suggest that lipase adsorption on hydrophobins follows an "interfacial activation" mechanism; immobilization on hydrophobins offers new possibilities for lipase study and modulation and reveals a new application for fungal hydrophobins.     

Electrospun polyacrylonitrile nanofibrous membranes for lipase immobilization

Polyacrylonitrile (PAN) nanofibers could be fabricated by electrospinning with fiber diameter in the range of 150–300 nm, providing huge surface area for enzyme immobilization and catalytic reactions. Lipase from Candida rugosa was covalently immobilized onto PAN nanofibers by amidination reaction. Aggregates of enzyme molecules were found on nanofiber surface from field emission scanning electron microscopy and covalent bond formation between enzyme molecule and the nanofiber was confirmed from FTIR measurements. After 5 min activation and 60 min reaction with enzyme-containing solution, the protein loading efficiency was quantitative and the activity retention of the immobilized lipase was 81% that of free enzyme. The mechanical strength of the NFM improved after lipase immobilization where tensile stress at break and Young's modulus were almost doubled. The immobilized lipase retained >95% of its initial activity when stored in buffer at 30 °C for 20 days, whereas free lipase lost 80% of its initial activity. The immobilized lipase still retained 70% of its specific activity after 10 repeated batches of reaction. This lipase immobilization method shows the best performance among various immobilized lipase systems using the same source of lipase and substrate when considering protein loading, activity retention, and kinetic parameters.     

The slow-down of the CALB immobilization rate permits to control the inter and intra molecular modification produced by glutaraldehyde

Lipase B from Candida antarctica (CALB) has been immobilized on octyl-agarose in two ways: rapidly, in 5 mM sodium phosphate (85% immobilization yield after 30 min), or slowly, in the presence of 30% (v/v) ethanol (40% immobilization yield after 30 min). Both biocatalysts were treated with glutaraldehyde in order to obtain different modification degrees on their amino groups (25, 50 and 100% modification). SDS-PAGE and detergent desorption experiments showed that, when the immobilization was performed in absence of ethanol, very large aggregates were formed by intermolecular crosslinking, while when 30% ethanol was added during immobilization, almost 90% of the enzyme remained as a monomer. The stability of both derivatives improved upon modification, both in thermal inactivation experiments (at pHs 5, 7 and 9) or in the presence of 50% (v/v) dimethylsulfoxide, achieving stabilization values ranging between 5 and 20 depending on the inactivation conditions. The stability increased proportionally with the modification degree, and was also higher when intermolecular bonds were performed (by a 2–4 factor). Moreover, the activity/pH profile was completely altered after enzyme modification, and, under certain conditions, the activity of the modified biocatalysts doubled that of the non-modified immobilized CALB. Results show that the addition of ethanol permits to have a distance between enzyme molecules that did not allow intermolecular crosslinking, and this has permitted to distinguish between the effects of intramolecular glutaraldehyde modifications and intermolecular glutaraldehyde crosslinking. The simple and controlled treatment of CALB-octyl with glutaraldehyde has proved to be an effective way to obtain a biocatalyst with improved activity and stability under different conditions.     

Decarboxylative aldol reaction catalysed by lipases and a protease in organic co-solvent mixtures and nearly anhydrous organic solvent media

Abstract

The effects of the choice of lipase, reaction medium, immobilization, presence of additives and temperature on conversion and stereoselectivity during a lipase catalysed decarboxylative aldol reaction were examined. It was shown that Candida antarctica lipase B (CALB) catalysed a decarboxylative aldol reaction between 4-nitrobenzaldehyde and ethyl acetoacetate in a 60% acetonitrile–40% aqueous buffer co-solvent mixture. Interestingly, free and immobilized forms of CALB showed opposite enantioselectivity in this media. The addition of 30 mol% imidazole increased the reaction rate from 8.5 to 55.7 μM min^??1 mg^??1. A 98% conversion could be achieved in 14 h (instead of 168 h) by adding imidazole. Other lipases also catalysed this reaction in different reaction media to a varying extent. With Mucor javanicus lipase in 30% DMSO, 20% enantiomeric excess (ee) of the (R)-product was observed. CALB also catalysed this reaction in nearly anhydrous acetonitrile. In the presence of cross-linked protein coated microcrystals of CALB, 90% conversion was obtained in this media in 24 h. A commercially available protease, alcalase, was also found to catalyse this reaction. While low water media gave poor conversion, the reaction in aqueous–60% acetonitrile co-solvent mixture gave 99% conversion in 72 h, provided imidazole was used as an additive.     

Improved activity of a lipase by vacuum drying on to a hydrophobic microporous support

Summary Lipase from Rhizopus arrhizus was immobilized by physical adsorption on hydrophobic microporous polypropylene supports. The immobilized enzyme catalyst was employed for the hydrolysis of palm kernel olein in the presence of n-hexane. The initial rate of lipolysis for vacuum dried immobilized lipase is nearly double that of air dried. The initial rate of lipolysis declines with increase of drying time. Immobilized lipase clearly reveals a relatively high initial rate after 30 days of storage at 4 °C. Stability of the immobilized lipase in buffer could be enhanced up to three-fold that of the free lipase.     

Immobilization of Candida antarctica Lipase B on fumed silica

Enzymes are usually immobilized on solid supports or solubilized when they are to be used in organic solvents with poor enzyme solubility. We have reported previously on a novel immobilization method for subtilisin Carlsberg on fumed silica with results that reached some of the best previously reported catalytic activities in hexane for this enzyme. Here we extend our method to Candida antarctica Lipase B (CALB) as an attractive target due to many potential applications of this enzyme in solvents. Our CALB/fumed silica preparations approached the catalytic activity of commercial Novozym 435 for a model esterification in hexane at 90 wt.% fumed silica (relative to the mass of the preparation). An intriguing observation was that the catalytic activity at first increases as more fumed silica was made available to the enzyme but then decreased precipitously when fumed silica exceeded 90 wt.%. This was not the case for s. Carlsberg where the catalytic activity leveled off at high relative amounts of fumed silica. We determined adsorption kinetics, performed variations of the pre-immobilization aqueous pH, determined the stability, and applied fluorescence microscopy to the preparations. A comparison with recent concepts by Gross et al. may point towards a rationale for an optimum intermediate surface coverage for some enzymes on solid supports.     

Activity and adsorption of lipase from Nigella sativa seeds on Celite at different pH values

Lipase from Nigella sativa seeds was immobilized by adsorption on Celite 535 from phosphate buffer solutions varying pH values of 5.0–8.0 at 25?°C. Langmuir isotherms described the adsorption equilibria well for lipase adsorption at all pH range. The saturation capacity for adsorption of lipase increased from 14.5 to 24.3 mg g^?1 Celite as the adsorption pH was reduced from 8 to 5, but the adsorption equilibrium constant remained constant and was determined to be 1.92 × 10⁵ M^?1. The adsorbed enzymes showed different activity values depending on the pH of the adsorption medium. The immobilized enzymes prepared at pH 6 displayed the highest activity values.     

Hydrolysis of butteroil by immobilized lipase using a hollow-fiber reactor: part I. lipase adsorption studies

Adsorption of proteins from a crude preparation containing a lipase from Aspergillus niger on microporous polypropylene hollow fibers was studied at six different temperatures. Langmuir isotherms accurately describe the overall adsorption equilibria. Lipase is selectively adsorbed relative to the other proteins in the crude preparation. Hence, immobilization also provides further purification of the lipase. The predictions of the Langmuir model for the change in the specific activity of lipase upon adsorption are consistent with experimental results. The loading capacity of the hollow fibers decreases and the adsorption constant increases as temperature is increased. This effect is more significant in the case of lipolytic activity than it is for the total amount of adsorbed protein. Small, positive enthalpy changes are associated with the adsorption of lipase on these hydrophobic membranes.     

A comparative performance evaluation of jute and eggshell matrices to immobilize pancreatic lipase

A pancreatic lipase was immobilized on readily available and inexpensive jute and eggshell matrices. The purity of extracted enzyme was confirmed by SDS-PAGE. The maximum protein load for eggshell was 10.23 mg/g, and for jute, it was 5.7 mg/g. The free enzyme activity retention was greater than 80% for eggshell and 43% for jute. The immobilized lipase was stable over a pH range from 7 to 8 for eggshell and 7.5 to 8.5 for jute with over a temperature range from 25 to 45 °C for eggshell and 37 to 40 °C for the jute. FTIR data indicated new bonds on the jute upon immobilization. Although no new bond was observed, immobilization data on eggshell fit well with the Langmuir adsorption isotherm model. The model constants, Γ_max and K_l, were 13.92 mg/g and 0.382 mL/mg, respectively. Mixed adsorption with both ionic and hydrophobic interactions was observed. Lipase adsorption was reduced significantly in presence of Tween 80, whereas the effect was less in case of ionic strength, pH and temperature. For both matrices, scanning electron microscopy (SEM) was used to demonstrate the changes in surface morphology after immobilization. The performance of eggshell was better than that of jute as a matrix for immobilizing pancreatic lipase.     

大孔树脂固定化脂肪酶及在微水相中催化合成生物柴油的研究

以不同大孔树脂吸附法固定化假丝酵母99_125脂肪酶,在微水有机相中的应用表明非极性树脂NKA是最佳的固定化载体。分别以正庚烷及磷酸盐缓冲液作为固定化介质,发现在正庚烷介质中树脂NKA的固定化效率能够达到98.98%,与采用磷酸盐缓冲液作为介质相比,固定化酶的水解活力和表观酶活回收率分别提高了4.07和3.43倍。考察了在微水相中固定化酶催化合成生物柴油的催化性能,结果表明,在给酶量为1.92∶1(初始酶粉与树脂的质量比),pH值为7.4,体系水含量为15%(水与油的质量比),反应温度为40℃条件下,固定化酶具有最佳的催化能力;以正庚烷为介质固定化脂肪酶催化合成生物柴油,采用三次流加甲醇的方式,单批转化率最高达到97.3%,连续反应19批以后转化率仍保持为70.2%。     

Comparison of covalent and physical immobilization of lipase in gigaporous polymeric microspheres

Lipase (EC 3.1.1.3) is a versatile enzyme which has been widely used in ester-reaction industries. We have previously discovered that gigaporous polystyrene (PST) microspheres can be used as a novel immobilization carrier for lipase. In this work, a series of gigaporous microspheres with different densities of epoxy group including poly(glycidyl methacrylate) (PGMA) and poly(styrene-co-glycidyl methacrylate) [P(ST-GMA)] were evaluated as lipase immobilization carriers, which were also compared with gigaporous PST microspheres and the commercial immobilized lipase Novozym 435. Lipase immobilized in gigaporous PGMA microspheres showed the highest activity yield, reusability, and stability as well as the best affinity for the substrate. The characterizations of adsorption curves, the change of epoxy group amounts, and hydrophobic–hydrophilic properties of the microspheres were carried out to investigate the interaction between lipase molecules and carriers. It was found that covalent binding played a key role in improving the properties of lipase immobilized in gigaporous PGMA microspheres.     

Immobilization on octyl-agarose beads and some catalytic features of commercial preparations of lipase a from Candida antarctica (Novocor ADL): Comparison with immobilized lipase B from Candida antarctica

Lipase A from Candida antarctica (CALA, commercialized as Novocor ADL) was immobilized on octyl-agarose, which is a very useful support for lipase immobilization, and coated with polyethylenimine to improve the stability. The performance was compared to that of the form B of the enzyme (CALB) immobilized on the same support, as both enzymes are among the most popular ones used in biocatalysis. CALA immobilization produced a significant increase in enzyme activity vs. p-nitrophenyl butyrate (pNPB) (by a factor of seven), and the coating with PEI did not have a significant effect on enzyme activity. CALB reduced its activity slightly after enzyme immobilization. Octyl-CALA was less stable than octyl-CALB at pH 9 and more stable at pH 5 and, more clearly, at pH 7. PEI coating only increased octyl-CALA stability at pH 9. In organic solvents, CALB had much better stability in methanol and was similarly stable in acetonitrile or dioxane. In these systems, the PEI coating of octyl-CALA permitted some stabilization. While octyl-CALA was more active vs. pNPB, octyl-CALB was much more active vs. mandelic esters or triacetin. Thus, depending on the specific reaction and the conditions, CALA or CALB may offer different advantages and drawbacks. © 2018 American Institute of Chemical Engineers Biotechnol. Prog., 35: e2735, 2019     

Versatility of glutaraldehyde to immobilize lipases: Effect of the immobilization protocol on the properties of lipase B from Candida antarctica

Glutaraldehyde chemistry has been used to immobilize lipase B from Candida antarctica (CALB) under different situations. Using high ionic strength, ionic adsorption is avoided, but CALB is adsorbed on the support via interfacial activation. Using non-ionic detergents (e.g., Triton X-100), the enzyme becomes ionically adsorbed on the activated support. If detergent and salt are simultaneously present during immobilization, a covalent attachment to the support is first produced. In absence of detergent or high ionic strength, a mixture of all of the previous immobilization reasons should coexist. Thus, 5 different CALB biocatalysts were prepared following the previous described protocols, and its stability and activity, pH/activity profile and specificity versus R and S methyl mandelate were analyzed. The existence of covalent attachment of more than 95% of the enzyme molecules was confirmed by washing the biocatalysts in salt and detergent solutions. The glutaraldehyde treatment of the enzyme adsorbed on aminated supports did not produce a significant improvement on the activity of the enzyme versus p-nitrophenylpropinate (pNPB) nor a high stabilization of the enzyme. This differed from the effects of a similar treatment of CAL adsorbed on octyl agarose. However, they were similar to the effects of this treatment on covalently immobilized CALB, suggesting that the immobilization protocol may greatly affect the final effect of a chemical modification on the enzyme properties.Dramatic changes in the enzyme features were observed comparing the different preparations, mainly in the specificity of CALB versus p-NPB and R-methyl mandelate (from 2.5 to 20), or in the enantiospecificity versus R/S methyl mandelate (from 1.8 to 16), confirming that these different immobilization protocols produced biocatalysts with different features. Moreover, changes in experimental conditions produced very different effects on the properties of the different CALB preparations.     

Biodiesel production from canola oil by using lipase immobilized onto hydrophobic microporous styrene–divinylbenzene copolymer

In this study, the methyl esters of the long chain fatty acids (biodiesel) were synthesized by methanolysis of canola oil by immobilized lipase. Lipase from Thermomyces lanuginosus was immobilized by both physical adsorption and covalent attachment onto polyglutaraldehyde activated styrene–divinylbenzene (STY–DVB) copolymer, which is synthesized by using high internal phase emulsion (polyHIPE). Two different STY–DVB copolymers were evaluated: STY–DVB copolymer and STY–DVB copolymer containing polyglutaraldehyde (STY–DVB–PGA). Lipase from T. lanuginosus was immobilized with 60% and 85% yield on the hydrophobic microporous STY–DVB and STY–DVB–PGA copolymer, respectively. Biodiesel production using the latter lipase preparation was realized by a three-step addition of methanol to avoid strong substrate inhibition. Under the optimized conditions, the maximum biodiesel yield was 97% at 50 °C in 24 h reaction. The immobilized enzyme retained its activity during the 10 repeated batch reactions.