Enhanced yield of medium-chain-length polyhydroxyalkanoates from nonanoic acid by co-feeding glucose in carbon-limited, fed-batch culture

Medium-chain-length polyhydroxyalkanoates (MCL-PHAs) were produced in carbon-limited, single-stage, fed-batch fermentations of Pseudomonas putida KT2440 by co-feeding nonanoic acid (NA) and glucose (G) to enhance the yield of PHA from NA. An exponential (μ = 0.25 h⁻¹) followed by a linear feeding strategy at a NA:G ratio of 1:1 (w/w) achieved 71 g l⁻¹ biomass containing 56% PHA. Although the same overall PHA productivity (1.44 g l⁻¹ h⁻¹) was obtained when NA alone was fed at the same specific growth rate, the overall yield of PHA from NA increased by 25% (0.66 g PHA g NA⁻¹ versus 0.53 g g⁻¹) with glucose co-feeding. Further increasing glucose in the feed (NA:G = 1:1.5) resulted in a slightly higher yield (0.69 g PHA g NA⁻¹) but lower PHA content (48%) and productivity (1.16 g l⁻¹ h⁻¹). There was very little change in the PHA composition.     

The relationship between Spirogyra (Zygnematophyceae, Streptophyta) filament type groups and environmental conditions in Central Europe

Species identification of the common filamentous green alga Spirogyra is mainly based on the conjugation process and zygospores. However, this genus is mostly found in its vegetative stage, which complicates studies on the ecological demands for individual species. We therefore used a different approach by assessing the relationship between vegetative Spirogyra filament type groups (morphotypes) and environmental conditions (mainly ions, nutrients, light supply and water temperature). Sampling was done at 133 sites in Central Europe and in total 333 different filament types were classified. Spirogyra was found at pH values between 6.2 and 9.1, while total alkalinity ranged from 0.6 to 7.9 mequiv l⁻¹. The genus is colonizing habitats with a specific conductivity between 75 and 1500 μS cm⁻¹. Total phosphorus amounts varied between 1 and 2240 μg l⁻¹ with a median value of 34 μg l⁻¹, indicating meso- to eutrophic conditions as optimal growth range. Filament type grouping by means of cluster analysis was based on cell cross walls (plane or replicate), average cell widths and average chloroplast numbers and resulted in 10 groups with plane cross walls and three with replicate cross walls. Canonical correspondence analysis revealed nutrients to be the key factor for morphotype occurrence: filaments with increased cell widths preferred elevated nutrient conditions. Other environmental variables (ions, buffer capacity, light supply and water temperature) had no significant effects on morphotype occurrence.     

Effects of carbon concentration and carbon to nitrogen ratio on the growth and sporulation of several biocontrol fungi

Effects of carbon concentration and carbon to nitrogen (C:N) ratio on six biocontrol fungal strains are reported in this paper. All fungal strains had extensive growth on the media supplemented with 6–12 g l⁻¹ carbon and C:N ratios from 10:1 to 80:1, and differed in nutrient requirements for sporulation. Except for the two strains of Paecilomyces lilacinus, all selected fungi attained the highest spore yields at a C:N ratio of 160:1 when the carbon concentration was 12 g l⁻¹ for Metarhizium anisopliae SQZ-1-21, 6 g l⁻¹ for M. anisopliae RS-4-1 and Trichoderma viride TV-1, and 8 g l⁻¹ for Lecanicillium lecanii CA-1-G. The optimal conditions for P. lilacinus sporulation were 8 g l⁻¹ carbon with a C:N ratio of 10:1 for M-14 and 12 g l⁻¹ carbon with a C:N ratio of 20:1 for IPC-P, respectively. The results indicated that the influence of carbon concentration and C:N ratio on fungal growth and sporulation is strain dependent; therefore, consideration for the complexity of nutrient requirements is essential for improving yields of fungal biocontrol agents.     

Differential sensitivity of fungi to lithium chloride in culture media

Forty species of fungi, representing a range of ecological and taxonomic groups, were tested for their ability to grow on agar media amended with lithium chloride (LiCl) at 1.5, 3 and 6 g l⁻¹. Species of Trichoderma varied considerably in their sensitivity to LiCl; at one week on 6 g l⁻¹ LiCl medium, the growth of seven species of Trichoderma was considerably inhibited; however, by three weeks at this level, four of the species tested were able to attain ≥30 % of control growth. Of the seven species tested, an isolate of T. viride was the most sensitive to LiCl in agar. Eleven other imperfect fungi also showed a range of ability to grow on agar amended with LiCl, from total inhibition to complete lack of inhibition. Six ascomycete fungi were greatly inhibited by LiCl at all levels; however, an isolate of Chaetomium globosum was highly tolerant of LiCl. Seven basidiomycete wood-decay fungi were quite sensitive to LiCl in agar, showing total to nearly total inhibition even at the lowest level; however, after three weeks, an isolate of Postia placenta was nearly uninhibited except at 6 g l⁻¹. Five ectomycorrhizal basidiomycete fungi were totally inhibited by all levels of LiCl; however, one ectomycorrhizal imperfect fungus (Cenococcum graniforme) was able to grow at 3 g l⁻¹ and was uninhibited at 1.5 g l⁻¹. Four zygomycete fungus isolates were nearly unaffected in their growth by all levels of LiCl.     

Toxicity of Dinophysis spp. in relation to population density and environmental conditions on the Swedish west coast

The aim of this study in the field was to investigate whether there are differences between the outer archipelago (Gullmar Fjord) and a semi-enclosed fjord system (Koljö Fjord) in occurrences of D. acuta and D. acuminata as well as in their content of diarrheic shellfish toxin (DST) per cell. When all data pairs of cell toxicity of D. acuminata and the corresponding number of cells l⁻¹ from the two sites were tested in a regression analysis, a statistically significant negative correlation became evident and was apparent as a straight line on a log–log plot (p < 0.0001). Obviously, there was an overall inverse relationship between the population density of D. acuminata and the toxin content per cell. Plotted on a linear scale, all data-pairs of cell toxicity and cell number made up a parabolic curve. On this curve the data-pairs could be separated into three groups: (i) D. acuminata occurring in numbers of fewer than approximately 100 cells l⁻¹, and with a toxin content per cell above 5 ρg cell⁻¹; (ii) cell numbers between 100 and approximately 250 cells l⁻¹ with a cell toxin content from 5 to 2 ρg cell⁻¹; (iii) when the population became greater than 250 cells l⁻¹, the toxicity, with few exceptions, was less than 2 ρg cell⁻¹. By applying this subdivision, some clear patterns of the distribution of the differently toxic D. acuminata became evident. When comparing the cell toxicity of the two sites, it was obvious that the D. acuminata cells from all depths from the Gullmar Fjord as a mean were significantly more toxic compared to the Koljö Fjord samples. The results have demonstrated that approximately 100 high-toxicity cells in a low-density population at surface may lead to the same accumulation of DST in a mussel as the ingestion of 1500 low-toxicity cells from a high-density pycnocline population.     

Enhancement of taxane production in hairy root culture of Taxus x media var. Hicksii

This study assessed the effect of two precursors (l-phenylalanine and p-amino benzoic acid) used alone or in combination with methyl jasmonate, on the growth and accumulation of paclitaxel, baccatin III and 10-deacetylbaccatin III in hairy root cultures of Taxus x media var. Hicksii. The greatest increase in dry biomass was observed after 4 weeks of culturing hairy roots in medium supplemented with 1 μM of l-phenylalanine (6.2 g L⁻¹). Addition of 1 μM of l-phenylalanine to the medium also resulted in the greatest 10-deacetylbaccatin III accumulation (422.7 μg L⁻¹), which was not detected in the untreated control culture. Supplementation with 100 μM of l-phenylalanine together with 100 μM of methyl jasmonate resulted in the enhancement of paclitaxel production from 40.3 μg L⁻¹ (control untreated culture) to 568.2 μg L⁻¹, the highest paclitaxel content detected in the study. The effect of p-amino benzoic acid on taxane production was less pronounced, and the highest yield of paclitaxel (221.8 μg L⁻¹) was observed when the medium was supplemented with 100 μM of the precursor in combination with methyl jasmonate.Baccatin III was not detected under the conditions used in this experiment and the investigated taxanes were not excreted into the medium.     

Increased xylitol production rate during long-term cell recycle fermentation of Candida tropicalis

Long-term cell recycle fermentations of Candida tropicalis were performed over 14 rounds of fermentation. The average xylitol concentrations, fermentation times, volumetric productivities and product yields for 14 rounds were 105 g l^–1, 333 h, 4.4 g l^–1 h^–1 and 78%, respectively, in complex medium; and 110 g l^–1, 284 h, 5.4 g l^–1 h^–1 and 81%, respectively, in a chemically defined medium. These productivities were 1.7 and 2.4 times those with batch fermentation in the complex and chemically defined media, respectively. The xylitol yield from xylose with cell recycle fermentation using the chemically defined medium was 81% (w/w), which was 7% greater than the xylitol yield with batch fermentation (74%); both modes of fermentation gave the same yield using the complex medium. These results suggest that the chemically defined medium is more suitable for production of xylitol than complex medium.     

Nitrogenous preference of toxigenic Pseudo-nitzschia australis (Bacillariophyceae) from field and laboratory experiments

Field and laboratory experiments were designed to determine the differential growth and toxin response to inorganic and organic nitrogen additions in Pseudo-nitzschia spp. Nitrogen enrichments of 50 μM nitrate (KNO₃), 10 μM ammonium (NH₄Cl), 20 μM urea and a control (no addition) were carried out in separate carboys with seawater collected from the mouth of the San Francisco Bay (Bolinas Bay), an area characterized by high concentrations of macronutrients and iron. All treatments showed significant increases in biomass, with chlorophyll a peaking on days 4–5 for all treatments except urea, which maintained exponential growth through the termination of the experiment. Pseudo-nitzschia australis Frenguelli abundance was 10³ cells l⁻¹ at the start of the experiment and increased by an order of magnitude by day 2. Particulate domoic acid (pDA) was initially low but detectable (0.15 μg l⁻¹), and increased throughout exponential and stationary phases across all treatments. At the termination of the experiment, the urea treatment produced more than double the amount of pDA (9.39 μg l⁻¹) than that produced by the nitrate treatment (4.26 μg l⁻¹) and triple that of the control and ammonium treatments (1.36 μg l⁻¹ and 2.64 μg l⁻¹, respectively). The mean specific growth rates, calculated from increases in chlorophyll a and from cellular abundance of P. australis, were statistically similar across all treatments.These field results confirmed laboratory experiments conducted with a P. australis strain isolated from Monterey Bay, CA (isolate AU221-a) grown in artificial seawater enriched with 50 μM nitrate, 50 μM ammonium or 25 μM of urea as the sole nitrogen source. The exponential growth rate of P. australis was significantly slower for cells grown on urea (ca. 0.5 day⁻¹) compared to the cells grown on either nitrate or ammonium (ca. 0.9 day⁻¹). However the urea-grown cells produced more particulate and dissolved domoic acid (DA) than the ammonium- or nitrate-grown cells. The field and laboratory experiments demonstrate that P. australis is able to grow effectively on urea as the primary source of nitrogen and produced more pDA when grown on urea in both natural assemblages and unialgal cultures. These results suggest that the influence of urea from coastal runoff may prove to be more important in the development or maintenance of toxic blooms than previously thought, and that the source of nitrogen may be a determining factor in the relative toxicity of west coast blooms of P. australis.     

Can soil Chytridiomycota survive and grow in different osmotic potentials?

Twenty isolates from soil in the orders Spizellomycetales, Blastocladiales and Chytridiales (Chytridiomycota) grew on complex solid media supplemented with 10 g l⁻¹ sodium chloride. In a synthetic liquid medium, 4.4 g l⁻¹ sodium chloride strongly inhibited growth in three of the five isolates, possibly because of the effect of the ions or osmolarity of the solution. The maximum concentration for growth in synthetic liquid medium with different osmotic potentials using polyethylene glycol (PEG) varied considerably amongst the isolates. Three patterns of growth with increasing concentrations of PEG were evident among isolates within the genus Rhizophydium. Up to the concentration where growth ceased, the dry weight of each isolate either decreased, remained constant, or in one case, increased. Most of the fungi survived when incubated at room temperature for 7 d in complex liquid media supplemented with 35 g l⁻¹ sodium chloride or 300 g l⁻¹ PEG. These data indicate that soil Chytridiomycota can survive various osmotic potentials that may occur during the wetting and drying phases in soils.     

Effect of culture medium composition on Trichoderma reesei’s morphology and cellulase production

The objective of this study was to determine how fungal morphology influences the volumetric cellulase productivity of Trichoderma reesei cultured in four media with lactose and lactobionic acid as fed-batch in a 7 L stirred tank bioreactor. The use of a cellulose–yeast extract culture medium yielded the highest enzyme production with a volumetric enzyme activity of 69.8 U L⁻¹ h⁻¹, and a maximum fungal biomass of 14.7 g L⁻¹. These findings were associated with the following morphological characteristics of the fungus: total mycelia was 98% of total mean projected area, mean hyphae length of 10 mm, mean hyphae volume of 45.1 mm³, mean hyphae diameter of 7.9 μm, number of branches 9, and number of tips per hypha 29. A positive correlation was found between the total mycelia, the number of tips and the volumetric enzyme productivity, indicating the weight of these variables on the enzyme productivity.     

Characteristics of fed-batch cultures of recombinant <Emphasis Type="Italic">Escherichia coli</Emphasis> containing human-like collagen cDNA at different specific growth rates

Fed-batch cultures of recombinant Escherichia coli BL21 for producing human-like collagen were performed at different specific growth rates (0.1~0.25 h⁻¹) before induction and at a constant value of 0.05 h⁻¹ after induction by the method of pseudo-exponential feeding. Although the final biomass (around 69 g l⁻¹) was almost the same in all fed-batch cultures, the highest product concentration (13.6 g l⁻¹) was achieved at the specific growth rate of 0.15 h⁻¹ and the lowest (9.6 g l⁻¹) at 0.25 h⁻¹. The mean productivity of human-like collagen was the highest at 0.15 h⁻¹ (0.57 g l⁻¹ h⁻¹) and the lowest at 0.1 h⁻¹ (0.35 g l⁻¹ h⁻¹). In the phase before induction, the cell yield coefficient (Y_X/S) decreased when the specific growth rate increased, while the formation of acetic acid increased upto 2.5 g l⁻¹ at 0.25 h⁻¹. The mean product yield coefficient (Y_P/S) also decreased with specific growth rate increasing. The respiration quotient (RQ) increased slightly with specific growth rate increasing before induction, and the mean value of RQ was around 72%. The optimum growth rate for human-like collagen production was 0.15~0.2 h⁻¹.     

Effects of oils and oil-related substrates on the synthetic activity of membrane-bound lipase from Rhizopus chinensis and optimization of the lipase fermentation media

The lipase from filamentous fungi Rhizopus chinensis, as a membrane-bound enzyme, possesses the excellent catalysis ability for esterification and transesterification reactions, and has a good potential in many industrial applications. In order to improve the synthetic activity of the lipase, the effects of oils and oil-related substrates on its production and the fermentation media optimization were investigated. Based on the results, it was suggested that oleic acid could be the important substrate for the lipase production. Among various oils and oil-related substrates, olive oil containing high content of oleic acid was the optimal one for the lipase production. Using orthogonal test and response surface methodology (RSM), the composition of fermentation media was further optimized. The optimized media for lipase synthetic activity and activity yield was composed of peptone 57.94 and 55.58 g L⁻¹, olive oil 21.94 and 22.99 g L⁻¹, maltose 12.91 and 14.34 g L⁻¹, respectively, with K₂HPO₄ 3 g L⁻¹, MgSO₄·7H₂O 5 g L⁻¹ and initial pH 6.0. Under the optimal conditions, the lipase activity and the activity yield were improved 61.5 and 93.4% comparing the results before optimization, respectively. The adequate models obtained had predicted the lipase production successfully.     

Cyanobacteria and cyanobacterial toxins in the alkaline crater lakes Sonachi and Simbi, Kenya

The phytoplankton communities and the production of cyanobacterial toxins were investigated in two alkaline Kenyan crater lakes, Lake Sonachi and Lake Simbi. Lake Sonachi was mainly dominated by the cyanobacterium Arthrospira fusiformis, Lake Simbi by A. fusiformis and Anabaenopsis abijatae. The phytoplankton biomasses measured were high, reaching up to 3159 mg l⁻¹ in L. Sonachi and up to 348 mg l⁻¹ in L. Simbi. Using HPLC techniques, one structural variant of the hepatotoxin microcystin (microcystin-RR) was found in L. Sonachi and four variants (microcystin-LR, -RR, -LA and -YR) were identified in L. Simbi. The neurotoxin anatoxin-a was found in both lakes. To our knowledge this is the first evidence of cyanobacterial toxins in L. Sonachi and L. Simbi. Total microcystin concentrations varied from 1.6 to 12.0 μg microcystin-LR equivalents g⁻¹ DW in L. Sonachi and from 19.7 to 39.0 μg microcystin-LR equivalents g⁻¹ DW in L. Simbi. Anatoxin-a concentrations ranged from 0.5 to 2.0 μg g⁻¹ DW in L. Sonachi and from 0 to 1.4 μg g⁻¹ DW in L. Simbi. In a monocyanobacterial strain of A. fusiformis, isolated from L. Sonachi, microcystin-YR and anatoxin-a were produced. The concentrations found were 2.2 μg microcystin g⁻¹ DW and 0.3 μg anatoxin-a g⁻¹ DW. This is the first study showing A. fusiformis as producer of microcystins and anatoxin-a. Since A. fusiformis occurs in mass developments in both lakes, a health risk for wildlife can be expected.     

Production of nisin Z using <Emphasis Type="Italic">Lactococcus lactis</Emphasis> IO-1 from hydrolyzed sago starch

A membrane bioreactor for production of nisin Z was constructed using Lactococcus lactis IO-1 in continuous culture using hydrolyzed sago starch as carbon source. A strategy used to enhance the productivity of nisin Z was to maintain the cells in a continuous growth at high cell concentration. This resulted in a volumetric productivity of nisin Z, as 50,000 IU l⁻¹ h⁻¹ using a cell concentration of 15 g l⁻¹, 30^°C, pH 5.5 and a dilution rate of 1.24 h⁻¹. Adding 10 g l⁻¹ YE and 2 g l⁻¹ polypeptone, other inducers were unnecessary to maintain production of nisin. The operating conditions of the reactor removed nisin and lactate, thus minimizing their effects which allowed the maintenance of cells in continuous exponential growth phase mode with high metabolic activity.     

Immobilized cells cultivated in semi-continuous mode in a fluidized bed reactor for xylitol production from sugarcane bagasse

Summary Xylitol production from sugarcane bagasse hemicellulosic hydrolyzate was evaluated in a fluidized bed reactor operated in semi-continuous mode, using cells immobilized on porous glass. The fermentative process was performed during five successive cycles of 72 h each one. The lowest xylitol production occurred in the first cycle, where a high cell concentration (12 g l⁻¹) was observed. In the subsequent cycles the xylitol concentration was ever increasing due to the cells adaptation to the medium. In the last one, 18 g xylitol l⁻¹ was obtained with a yield factor of 0.44 g g⁻¹ and volumetric productivity of 0.32 g l⁻¹ h⁻¹.     

Improved productivity of <Emphasis Type="Italic">β</Emphasis>-fructofuranosidase by a derepressed mutant of <Emphasis Type="Italic">Aspergillus niger</Emphasis> from conventional and non-conventional substrates

Summary Wild-type cultures of Aspergillus niger produced a basal level of β-fructofuranosidase on glucose of 1 IU l⁻¹ h⁻¹. In contrast, a catabolite-derepressed mutant strain of the same organism produced a markedly higher level (25 IU l⁻¹ h⁻¹) of this enzyme when grown on the same carbon source. Wheat bran induced both the wild type (252 IU l⁻¹ h⁻¹) and the mutant strain (516 IU l⁻¹ h⁻¹) to produce 252- to 516-fold higher levels of this enzyme than was observed with the wild-type grown on glucose and was the best carbon source. When corn steep liquor served as a nitrogen source, the wild-type organism showed a higher activity of enzyme on monosaccharides and disaccharides comparable to that produced by corncobs in the basal medium and that mutant was a potentially improved (> 2-fold) organism for the production of β-fructofuranosidase on all carbon sources. Enhanced substrate consumption and product formation kinetic parameters suggest that the mutant organism may be exploited for bulk production of this useful enzyme.     

Interaction Among Copper Toxicity,Temperature and Salinity on the Population Dynamics of <Emphasis Type="Italic">Brachionus Rotundiformis</Emphasis> (Rotifera)

Heavy metals may interact with ecological factors such as temperature, food level and salinity, causing both mortality and reduced reproduction in organisms. Among different heavy metals, copper compounds are commonly used for eliminating algal blooms in aquaculture tanks. At certain concentrations, copper is toxic to rotifers. In the present work, we evaluated the combined effects of salt concentrations (2.5 and 5.0 g l⁻¹ NaCl), copper levels (0, 0.03125, 0.0625, 0.125 and 0.25 mg l⁻¹ as CuCl₂) and two temperatures (20 and 25 °C) on the population growth of B. rotundiformis using Chlorella as the algal food (at 0.5 × 10⁶ cells ml⁻¹ for every 24 h). Regardless of salinity and temperature, copper at concentrations as low as 0.03 mg l⁻¹ had an adverse effect on the population growth of rotifers and above 0.125 mg l⁻¹, the populations did not grow. The effect of the toxicant on B. rotundiformis was more severe at 25° than at 20 °C at lower salinity. In general, we observed peak densities of rotifers around day 12 at 20 °C but 6–8 days earlier at 25 °C. Peak population densities of B. rotundiformis in the controls at the salinity of 2.5 g l⁻¹ ranged from 90 to 180 ind. ml⁻¹, depending on temperature; at a salinity of 5.0 g l⁻¹, these were lower. The population growth rates, r, in our study varied from +0.31 to –0.12 depending on the test conditions. There was a significant impact of temperature, salinity and toxicity level on the population growth rate of B. rotundiformis. Our results suggested that even narrow changes in salinity could negatively influence the toxicity of heavy metal on the population growth rates of B. rotundiformis.     

Biodegradation and detoxification of nicotine in tobacco solid waste by a Pseudomonas sp.

A Pseudomonas sp. grew with nicotine optimally 3 g l^–1 and at 30 °C and pH 7. Nicotine was fully degraded within 10 h. The resting cells degraded nicotine in tobacco solid waste completely within 6 h in 0.02 m sodium phosphate buffer (pH 7) at maximally 56 mg nicotine h^–1 g dry cell^–1.     

Acid hydrolysis of sugarcane bagasse for lactic acid production

In order to use sugarcane bagasse as a substrate for lactic acid production, optimum conditions for acid hydrolysis of the bagasse were investigated. After lignin extraction, the conditions were varied in terms of hydrochloric (HCl) or sulfuric (H₂SO₄) concentration (0.5–5%, v/v), reaction time (1–5 h) and incubation temperature (90–120 °C). The maximum catalytic efficiency (E) was 10.85 under the conditions of 0.5% of HCl at 100 °C for 5 h, which the main components (in g l⁻¹) in the hydrolysate were glucose, 1.50; xylose, 22.59; arabinose, 1.29; acetic acid, 0.15 and furfural, 1.19. To increase yield of lactic acid production from the hydrolysate by Lactococcus lactis IO-1, the hydrolysate was detoxified through amberlite and supplemented with 7 g l⁻¹ of xylose and 7 g l⁻¹ of yeast extract. The main products (in g l⁻¹) of the fermentation were lactic acid, 10.85; acetic acid, 7.87; formic acid, 6.04 and ethanol, 5.24.     

Succinic acid production by a newly isolated bacterium

A new bacterial strain producing succinic acid was enriched from bovine rumen content. It is facultatively anaerobic, belongs to the family Pasteurellaceae and has similarity to the genus Mannheimia. In batch cultivations with D-glucose or sucrose the strain produced up to 5.8 g succinic acid l⁻¹ with a productivity and a yield of up to 1.5 g l⁻¹ h⁻¹ and 0.6 g g⁻¹, respectively. With crude glycerol up to 8.4 g l⁻¹, 0.9 g l⁻¹ h⁻¹ and 1.2 g g⁻¹ were obtained. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.