Coated Lithium Powder (CLiP) Electrodes for Lithium‐Metal Batteries

Safety issues caused by the metallic lithium inside a battery represent one of the main reasons for the lack of commercial availability of rechargeable lithium‐metal batteries. The advantage of anodes based on coated lithium powder (CLiP), compared to plain lithium foil, include the suppression of dendrite formation, as the local current density during stripping/plating is reduced due to the higher surface area. Another performance and safety advantage of lithium powder is the precisely controlled mass loading of the lithium anode during electrode preparation, giving the opportunity to avoid Li excess in the cell. As an additional benefit, the coating makes electrode manufacturing safer and eases handling. Here, electrodes based on coated lithium powder electrodes (CLiP) are introduced for application in lithium‐metal batteries. These electrodes are compared to lithium foil electrodes with respect to cycling stability, coulombic efficiency of lithium stripping/plating, overpotential, and morphology changes during cycling.     

Synergistic Effect of 3D Current Collectors and ALD Surface Modification for High Coulombic Efficiency Lithium Metal Anodes

Improving the performance of Li metal anodes is a critical bottleneck to enable next‐generation battery systems beyond Li‐ion. However, stability issues originating from undesirable electrode/electrolyte interactions and Li dendrite formation have impaired long‐term cycling of Li metal anodes. Herein, a bottom‐up fabrication process is demonstrated for a current collector for Li metal electrodeposition and dissolution composed of highly uniform vertically aligned Cu pillars. By rationally controlling geometric parameters of the 3D current collector architecture, including pillar diameter, spacing, and length, the morphology of Li plating/stripping upon cycling can be controlled and optimal cycling performance can be achieved. In addition, it is demonstrated that deposition of an ultrathin layer of ZnO by atomic layer deposition on the current collector surface can facilitate the initial Li nucleation, which dictates the morphology and reversibility of subsequent cycling. This core–shell pillar architecture allows for the effects of geometry and surface chemistry to be decoupled and individually controlled to optimize the electrode performance in a synergistic manner. Using this platform, Li metal anodes are demonstrated with Coulombic efficiency up to 99.5%, providing a pathway toward high‐efficiency and long‐cycle life Li metal batteries with reduced excess Li loading.     

Toward the Sustainable Lithium Metal Batteries with a New Electrolyte Solvation Chemistry

Herein, a new solvation strategy enabled by Mg(NO₃)₂ is introduced, which can be dissolved directly as Mg²⁺ and NO₃^? ions in the electrolyte to change the Li⁺ ion solvation structure and greatly increase interfacial stability in Li‐metal batteries (LMBs). This is the first report of introducing Mg(NO₃)₂ additives in an ester‐based electrolyte composed of ternary salts and binary ester solvents to stabilize LMBs. In particular, it is found that NO₃^? efficiently forms a stable solid electrolyte interphase through an electrochemical reduction reaction, along with the other multiple anion components in the electrolyte. The interaction between Li⁺ and NO₃^? and coordination between Mg²⁺ and the solvent molecules greatly decreases the number of solvent molecules surrounding the Li⁺, which leads to facile Li⁺ desolvation during plating. In addition, Mg²⁺ ions are reduced to Mg via a spontaneous chemical reaction on the Li metal surface and subsequently form a lithiophilic Li–Mg alloy, suppressing lithium dendritic growth. The unique solvation chemistry of Mg(NO₃)₂ enables long cycling stability and high efficiency of the Li‐metal anode and ensures an unprecedented lifespan for a practical pouch‐type LMB with high‐voltage Ni‐rich NCMA73 cathode even under constrained conditions.     

A 3D Lithium/Carbon Fiber Anode with Sustained Electrolyte Contact for Solid‐State Batteries

To reconcile the energy storage ability and operational safety of lithium metal batteries (LMBs), a transformation from a liquid to a solid‐state system is required. However, Li volume variation, poor interfacial contact, and high operation temperatures hinder its practical applications. To address the above issues, here, an integral structure design for solid‐state LMBs is shown, in which a Li‐preinfused 3D carbon fiber (Li/CF) anode is ionically connected to a cathode via an autopolymerized gel electrolyte. The gel electrolyte helps to encapsulate the liquid electrolyte within the Li/CF anode and the cathode to improve the interfacial contact. The gel also serves as a reservoir that balances the liquid electrolyte supply during repeated Li stripping/plating process. As a result, the symmetrical cells and full cells with Li/CF electrodes exhibit improved cycling stability and effective suppression of dendrites at ambient temperature. This work facilitates the realization of solid‐state LMBs with high energy and high safety.     

Interface Engineering for Lithium Metal Anodes in Liquid Electrolyte

Interfacial chemistry between lithium metal anodes and electrolytes plays a vital role in regulating the Li plating/stripping behavior and improving the cycling performance of Li metal batteries. Constructing a stable solid electrolyte interphase (SEI) on Li metal anodes is now understood to be a requirement for progress in achieving feasible Li‐metal batteries. Recently, the application of novel analytical tools has led to a clearer understanding of composition and the fine structure of the SEI. This further promoted the development of interface engineering for stable Li metal anodes. In this review, the SEI formation mechanism, conceptual models, and the nature of the SEI are briefly summarized. Recent progress in probing the atomic structure of the SEI and elucidating the fundamental effect of interfacial stability on battery performance are emphasized. Multiple factors including current density, mechanical strength, operating temperature, and structure/composition homogeneity that affect the interfacial properties are comprehensively discussed. Moreover, strategies for designing stable Li‐metal/electrolyte interfaces are also reviewed. Finally, new insights and future directions associated with Li‐metal anode interfaces are proposed to inspire more revolutionary solutions toward commercialization of Li metal batteries.     

Ultrathin Bilayer of Graphite/SiO2 as Solid Interface for Reviving Li Metal Anode

Lithium metal anodes are expected to drive practical applications that require high energy‐density storage. However, the direct use of metallic lithium causes safety concerns, low rate capabilities, and poor cycling performance due to unstable solid electrolyte interphase (SEI) and undesired lithium dendrite growth. To address these issues, a radio frequency sputtered graphite‐SiO₂ ultrathin bilayer on a Li metal chips is demonstrated, for the first time, as an effective SEI layer. This leads to a dendrite free uniform Li deposition to achieve a stable voltage profile and outstanding long hours plating/stripping compared to the bare Li. Compared to a bare Li anode, the graphite‐SiO₂ bilayer modified Li anode coupled with lithium nickel cobalt manganese oxide cathode (NMC111) and lithium titanate shows improved capacity retention, higher capacity at higher rates, longer cycling stability, and lower voltage hysteresis. Graphite acts as an electrical bridge between the plated Li and Li electrode, which lowers the impedance and buffers the volume expansion during Li plating/stripping. Adding an ultrathin SiO₂ layer facilitates Li‐ion diffusion and lithiation/delithiation, provides higher electrolyte affinity, higher chemical stability, and higher Young's modulus to suppress the Li dendrite growth.     

Tailoring Lithium Deposition via an SEI‐Functionalized Membrane Derived from LiF Decorated Layered Carbon Structure

Lithium (Li) metal is a key anode material for constructing next generation high energy density batteries. However, dendritic Li deposition and unstable solid electrolyte interphase (SEI) layers still prevent practical application of Li metal anodes. In this work, it is demonstrated that an uniform Li coating can be achieved in a lithium fluoride (LiF) decorated layered structure of stacked graphene (SG), leading to the formation of an SEI‐functionalized membrane that retards electron transfer by three orders of magnitude to avoid undesirable Li deposition on the top surface, and ameliorates Li⁺ ion migration to enable uniform and dendrite‐free Li deposition beneath such an interlayer. Surface chemistry analysis and density functional theory calculations demonstrate that these beneficial features arise from the formation of C–F_x surface components on the SG sheets during the Li coating process. Based on such an SEI‐functionalized membrane, stable cycling at high current densities up to 3 mA cm^?2 and Li plating capacities up to 4 mAh cm^?2 can be realized in LiPF₆/carbonate electrolytes. This work elucidates the promising strategy of modifying Li plating behavior through the SEI‐functionalized carbon structure, with significantly improved cycling stability of rechargeable Li metal anodes.     

A Coaxial‐Interweaved Hybrid Lithium Metal Anode for Long‐Lifespan Lithium Metal Batteries

Lithium (Li) metal is one of the most promising anode materials to construct next‐generation rechargeable batteries owing to its ultrahigh theoretical capacity and the lowest electrochemical potential. Unfortunately, practical application of Li metal batteries is severely hindered by short lifespan and safety concerns caused by Li dendrite growth during cycling. Herein, a coaxial‐interweaved hybrid Li metal anode is proposed for dendrite inhibition that significantly improves the cycling stability of Li metal batteries. The hybrid Li metal anode is fabricated by Li composition into a 3D interweaved scaffold, where each fiber of the interwoven scaffold is composed of a conductive skeleton and a coaxial lithiophilic layer modified on the surface. The coaxial‐interweaved structure endows the hybrid anode with favored Li affinity to guide uniform Li deposition, sufficient channels for ion transportation and electron conduction, and enhanced stability during Li plating and stripping. Consequently, the hybrid Li metal anode affords high Coulombic efficiency over 98.5% for 750 cycles with dendrite‐free morphologies in half cells and improved capacity retention of 80.1% after 100 cycles in LiFePO₄ full cells. The innovative coaxial‐interweaved hybrid Li metal anode demonstrates multiscale design strategy from lithiophilic modification to scaffold construction and promises the prospect of Li metal batteries for future applications.     

Pristine or Highly Defective? Understanding the Role of Graphene Structure for Stable Lithium Metal Plating

The role of graphene host structure/chemistry in plating–stripping in lithium metal anodes employed for lithium metal batteries is first examined in this study. Structural and chemical defects are bad, since highly defective graphene promotes unstable solid electrolyte interphase (SEI) growth. This consumes the fluoroethylene carbonate (FEC) additive in the carbonate electrolyte and is correlated with rapid decay in Coulombic efficiency (CE) and formation of filament‐like Li dendrites. A unique flow‐aided sonication exfoliation method is employed to synthesize “defect‐free” graphene (df‐G), allowing for a direct performance comparison with conventional reduced graphene oxide (r‐GO). At cycle 1, the r‐GO is better electrochemically wetted by Li than df‐G, indicating that initially it is more lithiophilic. With cycling, the nucleation overpotential with r‐GO becomes higher than with df‐G, indicating less facile plating reactions. The df‐G yields state‐of‐the‐art electrochemical performance, with the post cycled metal surface being relatively smooth and dendrite‐free. Conversely, r‐GO templates have CE rapidly degrade from the onset, with extensive dendrites after cycling. Severe SEI growth and associated FEC depletion with r‐GO are further confirmed by electrochemical impedance analysis and surface science methods. A new design rule is provided for Li metal templates: An ideal host must be noncatalytic toward SEI formation.     

Al Doping for Mitigating the Capacity Fading and Voltage Decay of Layered Li and Mn‐Rich Cathodes for Li‐Ion Batteries

Li and Mn‐rich layered cathodes, despite their high specific capacity, suffer from capacity fading and discharge voltage decay upon cycling. Both specific capacity and discharge voltage of Li and Mn‐rich cathodes are stabilized upon cycling by optimized Al doping. Doping Li and Mn‐rich cathode materials Li_1.2Ni_0.16Mn_0.56Co_0.08O₂ by Al on the account of manganese (as reflected by their stoichiometry) results in a decrease in their specific capacity but increases pronouncedly their stability upon cycling. Li_1.2Ni_0.16Mn_0.51Al_0.05Co_0.08O₂ exhibits 96% capacity retention as compared to 68% capacity retention for Li_1.2Ni_0.16Mn_0.56Co_0.08O₂ after 100 cycles. This doping also reduces the decrease in the average discharge voltage upon cycling, which is the longstanding fatal drawback of these Li and Mn‐rich cathode materials. The electrochemical impedance study indicates that doping by Al has a surface stabilization effect on these cathode materials. The structural analysis of cycled electrodes by Raman spectroscopy suggests that Al doping also has a bulk stabilizing effect on the layered LiMO₂ phase resulting in the better electrochemical performance of Al doped cathode materials as compared to the undoped counterpart. Results from a prolonged systematic work on these cathode materials are presented and the best results that have ever been obtained are reported.     

Correlation between Li Plating Behavior and Surface Characteristics of Carbon Matrix toward Stable Li Metal Anodes

Carbonaceous materials are widely employed to host Li for stable and safe Li metal batteries while relatively little effort is devoted to tailoring the surface properties of carbon to facilitate uniform Li plating. Herein, the correlation between Li plating behavior and the surface characteristics of electrospun porous carbon nanofibers (PCNFs) is systemically elucidated through experiments and theoretical calculations. It is revealed that the neat carbon surface suffers from severe lattice mismatch with Li metal, hindering uniform Li plating. In contrast, open pores created on the PCNF surface serve as active sites for controlled initial nucleation of Li. The introduction of oxygenated functional groups further facilitates the nucleation of Li on PCNFs through the largely reduced nucleation energy barrier. The Li film uniformly deposited on PCNFs enables efficient use of the whole carbon surface, giving rise to enhanced cyclic stability of the electrode. When used as an anode in lithium–sulfur batteries, the modified electrode delivers an excellent energy density of 385 Wh kg^?1 after 100 cycles. The fundamental correlation established in this study is universal to all types of carbonaceous materials and sheds new light on the rational design of high‐performance Li metal anodes by controlling the initial Li nucleation.     

Universal Soldering of Lithium and Sodium Alloys on Various Substrates for Batteries

The high theoretical specific capacity of lithium (Li) metal and the nonflammability of solid‐state electrolytes (SSEs) make the solid‐state Li metal battery a promising option to develop safe batteries with high energy density. To make the switch from liquid to solid‐state electrolyte, the high interfacial resistance resulting from the poor solid–solid contacts between Li metal and SSEs needs to be addressed. Herein, a one‐step soldering technique to quickly coat molten Li onto different substrates including metals, ceramics, and polymers is presented. It is deduced that the surface energy and viscosity of the molten Li can be tuned by adding alloy elements, which improves the wettability against various substrates. When soldered onto the surface of garnet‐based SSEs, the Li alloys exhibit significantly improved contact, which leads to an interface resistance as low as ≈7 Ω cm². While cycling under high loads, the newly plated Li still maintains tight contact with the garnet surface and demonstrates excellent electrochemical stability. Several Li binary alloys as well as sodium (Na) binary alloys are successfully tested on various substrates to demonstrate the versatility of this soldering technique for potential battery applications.     

High Polarity Poly(vinylidene difluoride) Thin Coating for Dendrite‐Free and High‐Performance Lithium Metal Anodes

The high‐polarity β‐phase poly(vinylidene difluoride) (β‐PVDF), which has all trans conformation with F and H atoms located on the opposite sides of the polymer backbone, is demonstrated to be a promising artificial solid‐electrolyte interphase coating on both Cu and Li metal anodes for dendrite‐free Li deposition/stripping and enhanced cycling performance. A thin (≈4 µm) β‐PVDF coating on Cu enables uniform Li deposition/stripping at high current densities up to 5 mA cm^?2, Li‐plating capacity loadings of up to 4 mAh cm^?2, and excellent cycling stability over hundreds of cycles under practical conditions (1 mA cm^?2 with 2 mAh cm^?2). Full cells containing an LiFePO₄ cathode and an anode of either β‐PVDF coated Cu or Li also exhibit excellent cycling stability. The profound effects of the high‐polarity PVDF coating on dendrite suppression are attributed to the electronegative F‐rich interface that favors layer‐by‐layer Li deposition. This study offers a new strategy for the development of dendrite‐free metal anode technology.     

Electrokinetic Phenomena Enhanced Lithium‐Ion Transport in Leaky Film for Stable Lithium Metal Anodes

The application of lithium (Li) metal anodes in Li metal batteries has been hindered by growth of Li dendrites, which lead to short cycling life. Here a Li‐ion‐affinity leaky film as a protection layer is reported to promote a dendrite‐free Li metal anode. The leaky film induces electrokinetic phenomena to enhance Li‐ion transport, leading to a reduced Li‐ion concentration polarization and homogeneous Li‐ion distribution. As a result, the dendrite‐free Li metal anode during Li plating/stripping is demonstrated even at an extremely high deposition capacity (6 mAh cm^?2) and current density (40 mA cm^?2) with improved Coulombic efficiencies. A full cell battery with the leaky‐film protected Li metal as the anode and high‐areal‐capacity LiNi_0.8Co_0.1Mn_0.1O₂ (NCM‐811) (≈4.2 mAh cm^?2) or LiFePO₄ (≈3.8 mAh cm^?2) as the cathode shows improved cycling stability and capacity retention, even at lean electrolyte conditions.     

Facilitating Interfacial Stability Via Bilayer Heterostructure Solid Electrolyte Toward High‐energy,Safe and Adaptable Lithium Batteries

Solid‐state electrolytes are widely anticipated to enable the revival of high energy density and safe metallic Li batteries, however, their lower ionic conductivity at room temperature, stiff interfacial contact, and severe polarization during cycling continue to pose challenges in practical applications. Herein, a dual‐composite concept is applied to the design of a bilayer heterostructure solid electrolyte composed of Li⁺ conductive garnet nanowires (Li_6.75La₃Zr_1.75Nb_0.25O₁₂)/polyvinylidene fluoride‐co‐hexafluoropropylene (PVDF‐HFP) as a tough matrix and modified metal organic framework particles/polyethylene oxide/PVDF‐HFP as an interfacial gel. The integral ionic conductivity of the solid electrolyte reaches 2.0 × 10^?4 S cm^?1 at room temperature. In addition, a chemically/electrochemically stable interface is rapidly formed, and Li dendrites are well restrained by a robust inorganic shield and matrix. As a result, steady Li plating/stripping for more than 1700 h at 0.25 mA cm^?2 is achieved. Solid‐state batteries using this bilayer heterostructure solid electrolyte deliver promising battery performance (efficient capacity output and cycling stability) at ambient temperature (25 °C). Moreover, the pouch cells exhibit considerable flexibility in service and unexpected endurance under a series of extreme abuse tests including hitting with a nail, burning, immersion under water, and freezing in liquid nitrogen.     

Fast‐Charging and Ultrahigh‐Capacity Lithium Metal Anode Enabled by Surface Alloying

Li metal anodes are going through a great revival but they still encounter grand challenges. One often neglected issue is that most reported Li metal anodes are only cyclable under relatively low current density (<5 mA cm^?2) and small areal capacity (<5 mAh cm^?2), which essentially limits their high‐power applications and results in ineffective Li utilization (<1%). Herein, it is reported that surface alloyed Li metal anodes can enable reversible cycling with ultrafast rate and ultralarge areal capacity. Low‐cost Si wafers are used and are chemically etched down to 20–30 µm membranes. Simply laminating a Si membrane onto Li foil results in the formation of Li_xSi alloy film fused onto Li metal with mechanical robustness and high Li‐ion conductivity. Symmetric cell measurements show that the surface alloyed Li anode has excellent cycling stability, even under high current density up to 25 mA cm^?2 and unprecedented areal capacity up to 100 mAh cm^?2. Furthermore, the surface alloyed Li anode is paired with amorphous MoS₃ cathode and achieves remarkable full‐cell performance.     

Uniform Lithium Deposition Assisted by Single‐Atom Doping toward High‐Performance Lithium Metal Anodes

For a long time lithium (Li) metal has been considered one of the most promising anodes for next‐generation rechargeable batteries. Despite decades of concentrated research, its practical application is still hindered by dendritic Li deposition and infinite volume change of Li metal anodes. Here, atomically dispersed metals doped graphene is synthesized to regulate Li metal nucleation and guide Li metal deposition. The single‐atom (SA) metals, supported on the nitrogen‐doped graphene can not only increase the Li adsorption energy of the localized area around the metal atomic sites with a moderate adsorption energy gradient but also improve the atomic structural stability of the overall materials by constructing a coordination mode of M‐N_x‐C (M, N, and C denoted as metal, nitrogen, and carbon atoms, respectively). As a result, the as‐obtained electrode exhibits an ultralow voltage hysteresis of 19 mV, a high average Coulombic efficiency of 98.45% over 250 cycles, and a stable Li plating/stripping performance even at a high current density of 4.0 mA cm^?2. This work demonstrates the application of SA metal doping in the rational design of Li metal anodes and provides a new concept for further development of Li metal batteries.     

Stabilization of Li Metal Anode in DMSO‐Based Electrolytes via Optimization of Salt–Solvent Coordination for Li–O2 Batteries

The conventional electrolyte of 1 m lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) in dimethyl sulfoxide (DMSO) is unstable against the Li metal anode and therefore cannot be used directly in practical Li–O₂ batteries. Here, we demonstrate that a highly concentrated electrolyte based on LiTFSI in DMSO (with a molar ratio of 1:3) can greatly improve the stability of the Li metal anode against DMSO and significantly improve the cycling stability of Li–O₂ batteries. This highly concentrated electrolyte contains no free DMSO solvent molecules, but only complexes of (TFSI^?)_a ? Li⁺? (DMSO)_b (where a + b = 4), and thus enhances their stability with Li metal anodes. In addition, such salt–solvent complexes have higher Gibbs activation energy barriers than the free DMSO solvent molecules, indicating improved stability of the electrolyte against the attack of superoxide radical anions. Therefore, the stability of this highly concentrated electrolyte at both Li metal anodes and carbon‐based air electrodes has been greatly enhanced, resulting in improved cycling performance of Li–O₂ batteries. The fundamental stability of the electrolyte in the absence of free‐solvent against the chemical and electrochemical reactions can also be used to enhance the stability of other electrochemical systems.     

3D Vertically Aligned Li Metal Anodes with Ultrahigh Cycling Currents and Capacities of 10 mA cm−2/20 mAh cm−2 Realized by Selective Nucleation within Microchannel Walls

Although metallic lithium is regarded as the “Holy Grail” for next‐generation rechargeable batteries due to its high theoretical capacity and low overpotential, the uncontrollable Li dendrite growth, especially under high current densities and deep plating/striping, has inhibited its practical application. Herein, a 3D‐printed, vertically aligned Li anode (3DP‐VALi) is shown to efficiently guide Li deposition via a “nucleation within microchannel walls” process, enabling a high‐performance, dendrite‐free Li anode. Moreover, the microchannels within the microwalls are beneficial for promoting fast Li⁺ diffusion, supplying large space for the accommodation of Li during the plating/stripping process. The high‐surface‐area 3D anode design enables high operating current densities and high areal capacities. As a result, the Li–Li symmetric cells using 3DP‐VALi demonstrate excellent electrochemical performances as high as 10 mA cm^?2/10 mAh cm^?2 for 1500 h and 5 mA cm^?2/20 mAh cm^?2 for 400 h, respectively. Additionally, the Li–S and Li–LiFePO₄ cells using 3DP‐VALi anodes present excellent cycling stability up to 250 and 800 cycles at a rate of 1 C, respectively. It is believed that these new findings could open a new window for dendrite‐free metal anode design and pave the way toward energy storage devices with high energy/power density.     

An Interconnected Channel‐Like Framework as Host for Lithium Metal Composite Anodes

Lithium (Li) metal anodes have long been counted on to meet the increasing demand for high energy, high‐power rechargeable battery systems but they have been plagued by uncontrollable plating, unstable solid electrolyte interphase (SEI) formation, and the resulting low Coulombic efficiency. These problems are even aggravated under commercial levels of current density and areal capacity testing conditions. In this work, the channel‐like structure of a carbonized eggplant (EP) as a stable “host” for Li metal melt infusion, is utilized. With further interphase modification of lithium fluoride (LiF), the as‐formed EP–LiF composite anode maintains ≈90% Li metal theoretical capacity and can successfully suppress dendrite growth and volume fluctuation during cycling. EP–LiF offers much improved symmetric cell and full‐cell cycling performance with lower and more stable overpotential under various areal capacity and elevated rate capability. Furthermore, carbonized EP serves as a light‐weight high‐performance current collector, achieving an average Coulombic efficiency ≈99.1% in ether‐based electrolytes with 2.2 mAh cm^?2 cycling areal capacity. The natural structure of carbonized EP will inspire further artificial designs of electrode frameworks for both Li anode and sulfur cathodes, enabling promising candidates for next‐generation high‐energy density batteries.