Molecular Engineering Using an Anthanthrone Dye for Low‐Cost Hole Transport Materials: A Strategy for Dopant‐Free,High‐Efficiency,and Stable Perovskite Solar Cells

In this report, highly efficient and humidity‐resistant perovskite solar cells (PSCs) using two new small molecule hole transporting materials (HTM) made from a cost‐effective precursor anthanthrone (ANT) dye, namely, 4,10‐bis(1,2‐dihydroacenaphthylen‐5‐yl)‐6,12‐bis(octyloxy)‐6,12‐dihydronaphtho[7,8,1,2,3‐nopqr]tetraphene (ACE‐ANT‐ACE) and 4,4′‐(6,12‐bis(octyloxy)‐6,12‐dihydronaphtho[7,8,1,2,3‐nopqr]tetraphene‐4,10‐diyl)bis(N,N‐bis(4‐methoxyphenyl)aniline) (TPA‐ANT‐TPA) are presented. The newly developed HTMs are systematically compared with the conventional 2,2′,7,7′‐tetrakis(N,N′‐di‐p‐methoxyphenylamino)‐9,9′‐spirbiuorene (Spiro‐OMeTAD). ACE‐ANT‐ACE and TPA‐ANT‐TPA are used as a dopant‐free HTM in mesoscopic TiO₂/CH₃NH₃PbI₃/HTM solid‐state PSCs, and the performance as well as stability are compared with Spiro‐OMeTAD‐based PSCs. After extensive optimization of the metal oxide scaffold and device processing conditions, dopant‐free novel TPA‐ANT‐TPA HTM‐based PSC devices achieve a maximum power conversion efficiency (PCE) of 17.5% with negligible hysteresis. An impressive current of 21 mA cm^?2 is also confirmed from photocurrent density with a higher fill factor of 0.79. The obtained PCE of 17.5% utilizing TPA‐ANT‐TPA is higher performance than the devices prepared using doped Spiro‐OMeTAD (16.8%) as hole transport layer at 1 sun condition. It is found that doping of LiTFSI salt increases hygroscopic characteristics in Spiro‐OMeTAD; this leads to the fast degradation of solar cells. While, solar cells prepared using undoped TPA‐ANT‐TPA show dewetting and improved stability. Additionally, the new HTMs form a fully homogeneous and completely covering thin film on the surface of the active light absorbing perovskite layers that acts as a protective coating for underlying perovskite films. This breakthrough paves the way for development of new inexpensive, more stable, and highly efficient ANT core based lower cost HTMs for cost‐effective, conventional, and printable PSCs.     

Molecular Engineered Hole‐Extraction Materials to Enable Dopant‐Free,Efficient p‐i‐n Perovskite Solar Cells

Two hole‐extraction materials (HEMs), TPP‐OMeTAD and TPP‐SMeTAD, have been developed to facilitate the fabrication of efficient p‐i‐n perovskite solar cells (PVSCs). By replacing the oxygen atom on HEM with sulfur (from TPP‐OMeTAD to TPP‐SMeTAD), it effectively lowers the highest occupied molecular orbital of the molecule and provides stronger Pb? S interaction with perovskites, leading to efficient charge extraction and surface traps passivation. The TPP‐SMeTAD‐based PVSCs exhibit both improved photovoltaic performance and reduced hysteresis in p‐i‐n PVSCs over those based on TPP‐OMeTAD. This work not only provides new insights on creating perovskite‐HEM heterojunction but also helps in designing new HEM to enable efficient organic–inorganic hybrid PVSCs.     

Few‐Layer MoS2 Flakes as Active Buffer Layer for Stable Perovskite Solar Cells

Solution‐processed few‐layer MoS₂ flakes are exploited as an active buffer layer in hybrid lead–halide perovskite solar cells (PSCs). Glass/FTO/compact‐TiO₂/mesoporous‐TiO₂/CH₃NH₃PbI₃/MoS₂/Spiro‐OMeTAD/Au solar cells are realized with the MoS₂ flakes having a twofold function, acting both as a protective layer, by preventing the formation of shunt contacts between the perovskite and the Au electrode, and as a hole transport layer from the perovskite to the Spiro‐OMeTAD. As prepared PSC demonstrates a power conversion efficiency (η) of 13.3%, along with a higher lifetime stability over 550 h with respect to reference PSC without MoS₂ (Δη/η = ?7% vs. Δη/η = ?34%). Large‐area PSCs (1.05 cm² active area) are also fabricated to demonstrate the scalability of this approach, achieving η of 11.5%. Our results pave the way toward the implementation of MoS₂ as a material able to boost the shelf life of large‐area perovskite solar cells in view of their commercialization.     

Molecular Engineering of Copper Phthalocyanines: A Strategy in Developing Dopant‐Free Hole‐Transporting Materials for Efficient and Ambient‐Stable Perovskite Solar Cells

Copper (II) phthalocyanines (CuPcs) have attracted growing interest as promising hole‐transporting materials (HTMs) in perovskite solar cells (PSCs) due to their low‐cost and excellent stability. However, the most efficient PSCs using CuPc‐based HTMs reported thus far still rely on hygroscopic p‐type dopants, which notoriously deteriorate device stability. Herein, two new CuPc derivatives are designed, namely CuPc‐Bu and CuPc‐OBu, by molecular engineering of the non‐peripheral substituents of the Pc rings, and applied as dopant‐free HTMs in PSCs. Remarkably, a small structural change from butyl groups to butoxy groups in the substituents of the Pc rings significantly influences the molecular ordering and effectively improves the hole mobility and solar cell performance. As a consequence, PSCs based on dopant‐free CuPc‐OBu as HTMs deliver an impressive power conversion efficiency (PCE) of up to 17.6% under one sun illumination, which is considerably higher than that of devices with CuPc‐Bu (14.3%). Moreover, PSCs containing dopant‐free CuPc‐OBu HTMs show a markedly improved ambient stability when stored without encapsulation under ambient conditions with a relative humidity of 85% compared to devices containing doped Spiro‐OMeTAD. This work thus provides a fundamental strategy for the future design of cost‐effective and stable HTMs for PSCs and other optoelectronic devices.     

Charge Transfer from Methylammonium Lead Iodide Perovskite to Organic Transport Materials: Efficiencies,Transfer Rates,and Interfacial Recombination

Perovskite‐based photovoltaics have been rapidly developed, with record power conversion efficiencies now exceeding 22%. In order to rationally design efficient and stable perovskite solar cells, it is important to understand not only charge trapping and recombination events, but also processes occurring at the perovskite/transport material (TM) interface, such as charge transfer and interfacial recombination. In this work, time‐resolved microwave conductivity measurements are performed to investigate these interfacial processes for methylammonium lead iodide and various state‐of‐the‐art organic TMs. A global kinetic model is developed, which accurately describes both the dynamics of excess charges in the perovskite layer and transfer to charge‐specific TMs. The authors conclude that for state‐of‐the‐art materials, such as Spiro‐OMeTAD and PCBM, the charge extraction efficiency is not significantly affected by intra‐band gap traps for trap densities under 10¹⁵ cm^–3. Finally, the transfer rates to C60, PCBM, EDOT‐OMeTPA, and Spiro‐OMeTAD are sufficient to outcompete second order recombination under excitation densities representative for illumination by AM1.5.     

Copper Salts Doped Spiro‐OMeTAD for High‐Performance Perovskite Solar Cells

The development of effective and stable hole transporting materials (HTMs) is very important for achieving high‐performance planar perovskite solar cells (PSCs). Herein, copper salts (cuprous thiocyanate (CuSCN) or cuprous iodide (CuI)) doped 2,2,7,7‐tetrakis(N,N‐di‐p‐methoxyphenylamine)‐9,9‐spirobifluorene (spiro‐OMeTAD) based on a solution processing as the HTM in PSCs is demonstrated. The incorporation of CuSCN (or CuI) realizes a p‐type doping with efficient charge transfer complex, which results in improved film conductivity and hole mobility in spiro‐OMeTAD:CuSCN (or CuI) composite films. As a result, the PCE is largely improved from 14.82% to 18.02% due to obvious enhancements in the cell parameters of short‐circuit current density and fill factor. Besides the HTM role, the composite film can suppress the film aggregation and crystallization of spiro‐OMeTAD films with reduced pinholes and voids, which slows down the perovskite decomposition by avoiding the moisture infiltration to some extent. The finding in this work provides a simple method to improve the efficiency and stability of planar perovskite solar cells.     

Enhanced Stability of Perovskite Solar Cells Incorporating Dopant‐Free Crystalline Spiro‐OMeTAD Layers by Vacuum Sublimation

The main handicap still hindering the eventual exploitation of organometal halide perovskite‐based solar cells is their poor stability under prolonged illumination, ambient conditions, and increased temperatures. This article shows for the first time the vacuum processing of the most widely used solid‐state hole conductor (SSHC), i.e., the Spiro‐OMeTAD [2,2′,7,7′‐tetrakis (N,N‐di‐p‐methoxyphenyl‐amine) 9,9′‐spirobifluorene], and how its dopant‐free crystalline formation unprecedently improves perovskite solar cell (PSC) stability under continuous illumination by about two orders of magnitude with respect to the solution‐processed reference and after annealing in air up to 200 °C. It is demonstrated that the control over the temperature of the samples during the vacuum deposition enhances the crystallinity of the SSHC, obtaining a preferential orientation along the π–π stacking direction. These results may represent a milestone toward the full vacuum processing of hybrid organic halide PSCs as well as light‐emitting diodes, with promising impacts on the development of durable devices. The microstructure, purity, and crystallinity of the vacuum sublimated Spiro‐OMeTAD layers are fully elucidated by applying an unparalleled set of complementary characterization techniques, including scanning electron microscopy, X‐ray diffraction, grazing‐incidence small‐angle X‐ray scattering and grazing‐incidence wide‐angle X‐ray scattering, X‐ray photoelectron spectroscopy, and Rutherford backscattering spectroscopy.     

4‐Tert‐butylpyridine Free Organic Hole Transporting Materials for Stable and Efficient Planar Perovskite Solar Cells

4‐Tert ‐butylpyridine (t BP) is an important additive in triarylamine‐based organic hole‐transporting materials (HTMs) for improving the efficiency and steady‐state performance of perovskite solar cells (PVSCs). However, the low boiling point of t BP (196 °C) significantly affects the long‐term stability and device performance of PVSCs. Herein, the design and synthesis of a series of covalently linked Spiro[fluorene‐9,9′‐xanthene] (SFX)‐based organic HTMs and pyridine derivatives to realize efficient and stable planar PVSCs are reported. One of the tailored HTMs, N2,N2,N7,N7‐tetrakis(4‐methoxyphenyl)‐3′,6′‐bis(pyridin‐4‐ylmethoxy) spiro[fluorene‐9,9′‐xanthene]‐2,7‐diamine ( XPP ) with two para‐position substituted pyridines that immobilized on the SFX core unit shows a high power conversion efficiency (PCE) of 17.2% in planar CH₃NH₃PbI₃‐based PVSCs under 100 mW cm^?2 AM 1.5G solar illumination, which is much higher than the efficiency of 5.5% that using the well‐known 2,2′,7,7′‐tetrakis‐(N ,N ‐di‐p ‐methoxy‐phenyl‐amine)9,9′‐spirobifluorene (Spiro‐OMeTAD) as HTM (without t BP) under the same condition. Most importantly, the pyridine‐functionalized HTM‐based PVSCs without t BP as additive show much better long‐term stability than that of the state‐of‐the‐art HTM Spiro‐OMeTAD‐based solar cells that containing t BP as additive. This is the first case that the t BP‐free HTMs are demonstrated in PVSCs with high PCEs and good stability. It paves the way to develop highly efficient and stable t BP‐free HTMs for PVSCs toward commercial applications.     

Spiro‐Phenylpyrazole‐9,9′‐Thioxanthene Analogues as Hole‐Transporting Materials for Efficient Planar Perovskite Solar Cells

Perovskite solar cells have emerged as a promising technique for low‐cost, light weight, and highly efficient photovoltaics. However, they still largely rely on 2,2′,7,7′‐tetrakis(N,N‐di‐p‐methoxyphenylamine)‐9,9′‐spirobifluorene (Spiro‐OMeTAD) to serve as hole‐transporting materials (HTMs). Here, a series of HTMs with small molecular weight is designed, which are constructed on a spiro core involving phenylpyrazole and a second heteroaromatics, i.e., xanthene (O atom), thioxanthene (S atom), and acridine (N atom). Through varying from phenylpyrazole substituted xanthene ( PPyra‐XA ), thioxanthene ( PPyra‐TXA ), to acridine ( PPyra‐ACD ), their optical and electrochemical properties, hole mobilities, and the photovoltaic performance are optimized. As a consequence, PPyra‐TXA based device exhibits the highest power conversion efficiency (PCE) of 18.06%, outperforming that of Spiro‐OMeTAD (16.15%), which could be attributed to the enhancement of hole mobility exerted by the thioxanthene. In addition, the dopant‐free device shows PCE of 11.7%. These results open a new direction for designing spiro‐HTMs by simple modification of chemical structures.     

LiTFSI‐Free Spiro‐OMeTAD‐Based Perovskite Solar Cells with Power Conversion Efficiencies Exceeding 19%

To date, the most efficient perovskite solar cells (PSCs) employ an n–i–p device architecture that uses a 2,2′,7,7′‐tetrakis(N,N‐di‐p‐methoxyphenyl‐amine)‐9,9′‐spirobifluorene (spiro‐OMeTAD) hole‐transporting material (HTM), which achieves optimum conductivity with the addition of lithium bis(trifluoromethane)sulfonimide (LiTFSI) and air exposure. However, this additive along with its oxidation process leads to poor reproducibility and is detrimental to stability. Herein, a dicationic salt spiro‐OMeTAD(TFSI)₂, is employed as an effective p‐dopant to achieve power conversion efficiencies of 19.3% and 18.3% (apertures of 0.16 and 1.00 cm²) with excellent reproducibility in the absence of LiTFSI and air exposure. As far as it is known, these are the highest‐performing n–i–p PSCs without LiTFSI or air exposure. Comprehensive analysis demonstrates that precise control of the proportion of [spiro‐OMeTAD]⁺ directly provides high conductivity in HTM films with low series resistance, fast hole extraction, and lower interfacial charge recombination. Moreover, the spiro‐OMeTAD(TFSI)₂‐doped devices show improved stability, benefitting from well‐retained HTM morphology without forming aggregates or voids when tested under an ambient atmosphere. A facile approach is presented to fabricate highly efficient PSCs by replacing LiTFSI with spiro‐OMeTAD(TFSI)₂. Furthermore, this study provides an insight into the relationship between device performance and the HTM doping level.     

Development of Dopant‐Free Organic Hole Transporting Materials for Perovskite Solar Cells

There has been considerable progress over the last decade in development of the perovskite solar cells (PSCs), with reported performances now surpassing 25.2% power conversion efficiency. Both long‐term stability and component costs of PSCs remain to be addressed by the research community, using hole transporting materials (HTMs) such as 2,2′,7,7′‐tetrakis(N,N′‐di‐pmethoxyphenylamino)‐9,9′‐spirbiuorene(Spiro‐OMeTAD) and poly[bis(4‐phenyl)(2,4,6‐trimethylphenyl)amine] (PTAA). HTMs are essential for high‐performance PSC devices. Although effective, these materials require a relatively high degree of doping with additives to improve charge mobility and interlayer/substrate compatibility, introducing doping‐induced stability issues with these HTMs, and further, additional costs and experimental complexity associated with using these doped materials. This article reviews dopant‐free organic HTMs for PSCs, outlining reports of structures with promising properties toward achieving low‐cost, effective, and scalable materials for devices with long‐term stability. It summarizes recent literature reports on non‐doped, alternative, and more stable HTMs used in PSCs as essential components for high‐efficiency cells, categorizing HTMs as reported for different PSC architectures in addition to use of dopant‐free small molecular and polymeric HTMs. Finally, an outlook and critical assessment of dopant‐free organic HTMs toward commercial application and insight into the development of stable PSC devices is provided.     

Why are Hot Holes Easier to Extract than Hot Electrons from Methylammonium Lead Iodide Perovskite?

Charge‐carriers photoexcited above a semiconductor's bandgap rapidly thermalize to the band‐edge. The cooling of these difficult to collect “hot” carriers caps the available photon energy that solar cells–including efficient perovskite solar cells–may utilize. Here, the dynamics and efficiency of hot carrier extraction from MAPbI₃ (MA = methylammonium) perovskite by spiro‐OMeTAD (a hole‐transporting layer) and TiO₂ (an electron‐transporting layer) are investigated and explained using both ultrafast electronic spectroscopy and theoretical modeling. Time‐resolved spectroscopy reveals a quasi‐equilibrium distribution of hot carriers forming upon excess‐energy excitation of the perovskite–a distribution largely unaffected by the presence of TiO₂. In contrast, the quasi‐equilibrium distribution of hot carriers is virtually nonexistent when spiro‐OMeTAD is present, which is indicative of efficient hot hole extraction at the interface of MAPbI₃. Density functional theory calculations predict that deep energy‐levels of MAPbI₃ exhibit electronically delocalized character, with significant overlap with the localized valence band charge of the spiro‐OMeTAD molecules lying on the surface of MAPbI₃. Consequently, hot holes are easily extracted from the deep energy‐levels of MAPbI₃ by spiro‐OMeTAD. These findings uncover the origins of efficient hot hole extraction in perovskites and offer a practical blueprint for optimizing solar cell interlayers to enable hot carrier utilization.     

High‐Performance and Stable Perovskite Solar Cells Based on Dopant‐Free Arylamine‐Substituted Copper(II) Phthalocyanine Hole‐Transporting Materials

A power conversion efficiency (PCE) as high as 19.7% is achieved using a novel, low‐cost, dopant‐free hole transport material (HTM) in mixed‐ion solution‐processed perovskite solar cells (PSCs). Following a rational molecular design strategy, arylamine‐substituted copper(II) phthalocyanine (CuPc) derivatives are selected as HTMs, reaching the highest PCE ever reported for PSCs employing dopant‐free HTMs. The intrinsic thermal and chemical properties of dopant‐free CuPcs result in PSCs with a long‐term stability outperforming that of the benchmark doped 2,2′,7,7′‐Tetrakis‐(N,N‐di‐p‐methoxyphenylamine)‐9,9′‐Spirobifluorene (Spiro‐OMeTAD)‐based devices. The combination of molecular modeling, synthesis, and full experimental characterization sheds light on the nanostructure and molecular aggregation of arylamine‐substituted CuPc compounds, providing a link between molecular structure and device properties. These results reveal the potential of engineering CuPc derivatives as dopant‐free HTMs to fabricate cost‐effective and highly efficient PSCs with long‐term stability, and pave the way to their commercial‐scale manufacturing. More generally, this case demonstrates how an integrated approach based on rational design and computational modeling can guide and anticipate the synthesis of new classes of materials to achieve specific functions in complex device structures.     

Dopant‐Free Hole Transporting Polymers for High Efficiency,Environmentally Stable Perovskite Solar Cells

Over the past five years, a rapid progress in organometal‐halide perovskite solar cells has greatly influenced emerging solar energy science and technology. In perovksite solar cells, the overlying hole transporting material (HTM) is critical for achieving high power conversion efficiencies (PCEs) and for protecting the air‐sensitive perovskite active layer. This study reports the synthesis and implementation of a new polymeric HTM series based on semiconducting 4,8‐dithien‐2‐yl‐benzo[1,2‐d;4,5‐d′]bistriazole‐alt‐benzo[1,2‐b:4,5‐b′]dithiophenes (pBBTa‐BDTs), yielding high PCEs and environmentally‐stable perovskite cells. These intrinsic (dopant‐free) HTMs achieve a stabilized PCE of 12.3% in simple planar heterojunction cells—the highest value to date for a polymeric intrinsic HTM. This high performance is attributed to efficient hole extraction/collection (the most efficient pBBTa‐BDT is highly ordered and orients π‐face‐down on the perovskite surface) and balanced electron/hole transport. The smooth, conformal polymer coatings suppress aerobic perovskite film degradation, significantly enhancing the solar cell 85 °C/65% RH PCE stability versus typical molecular HTMs.     

Low‐Cost N,N′‐Bicarbazole‐Based Dopant‐Free Hole‐Transporting Materials for Large‐Area Perovskite Solar Cells

Despite the recent unprecedented development of efficient dopant‐free hole transporting materials (HTMs) for high‐performance perovskite solar cells (PSCs) on small‐area devices (≤0.1 cm²), low‐cost dopant‐free HTMs for large‐area PSCs (≥1 cm²) with high power conversion efficiencies (PCEs) have rarely been reported. Herein, two novel HTMs, 3,3′,6,6′ (or 2,2′,7,7′)‐tetrakis(N,N′‐di‐p‐methoxyphenylamine)‐N,N′‐bicarbazole (3,6 BCz‐OMeTAD or 2,7 BCz‐OMeTAD), are synthesized via an extremely simple route from very cheap raw materials. Owing to their excellent film‐forming abilities and matching energy levels, 3,6 BCz‐OMeTAD and 2,7 BCz‐OMeTAD can be successfully employed as a perfect ultrathin (≈30 nm) hole transporting layer in large‐area PSCs up to 1 cm². The 3,6 BCz‐OMeTAD and 2,7 BCz‐OMeTAD based large‐area PSCs show highest PCEs up to 17.0% and 17.6%, respectively. More importantly, high performance large‐area PSCs based on 2,7 BCz‐OMeTAD retain 90% of the initial efficiency after 2000 h storage in an ambient environment without encapsulation.     

Integrated Design of Organic Hole Transport Materials for Efficient Solid‐State Dye‐Sensitized Solar Cells

A series of triphenylamine‐based small molecule organic hole transport materials (HTMs) with low crystallinity and high hole mobility are systematically investigated in solid‐state dye‐sensitized solar cells (ssDSCs). By using the organic dye LEG4 as a photosensitizer, devices with X3 and X35 as the HTMs exhibit desirable power conversion efficiencies (PCEs) of 5.8% and 5.5%, respectively. These values are slightly higher than the PCE of 5.4% obtained by using the state‐of‐the‐art HTM Spiro‐OMeTAD. Meanwhile, transient photovoltage decay measurement is used to gain insight into the complex influences of the HTMs on the performance of devices. The results demonstrate that smaller HTMs induce faster electron recombination in the devices and suggest that the size of a HTM plays a crucial role in device performance, which is reported for the first time.     

High Electron Affinity Enables Fast Hole Extraction for Efficient Flexible Inverted Perovskite Solar Cells

Inverted perovskite solar cells (PSCs) with low‐temperature processed hole transporting materials (HTMs) suffer from poor performance due to the inferior hole‐extraction capability at the HTM/perovskite interfaces. Here, molecules with controlled electron affinity enable a HTM with conductivity improved by more than ten times and a decreased energy gap between the Fermi level and the valence band from 0.60 to 0.24 eV, leading to the enhancement of hole‐extraction capacity by five times. As a result, the 3,6‐difluoro‐2,5,7,7,8,8‐hexacyanoquinodimethane molecules are used for the first time enhancing open‐circuit voltage (V_oc) and fill factor (FF) of the PSCs, which enable rigid‐and flexible‐based inverted perovskite devices achieving highest power conversion efficiencies of 22.13% and 20.01%, respectively. This new method significantly enhances the V_oc and FF of the PSCs, which can be widely combined with HTMs based on not only NiO_x but also PTAA, PEDOTT:PSS, and CuSCN, providing a new way of realizing efficient inverted PSCs.     

Solution Processable Inorganic–Organic Double‐Layered Hole Transport Layer for Highly Stable Planar Perovskite Solar Cells

Perovskite solar cells (PSCs) have reached their highest efficiency with 2,2′,7,7′‐tetrakis(N,N′‐di‐p‐methoxyphenylamine)‐9,9′‐spirobifluorene (spiro‐OMeTAD). However, this material can cause problems with respect to reproducibility and stability. Herein, a solution‐processable inorganic–organic double layer based on tungsten oxide (WO₃) and spiro‐OMeTAD is reported as a hole transport layer in PSCs. The device equipped with a WO₃/spiro‐OMeTAD layer achieves the highest efficiency (21.44%) in the tin (IV) oxide planar structure. The electronic properties of the double layer are thoroughly analyzed using photoluminescence, space‐charge–limited current, and electrochemical impedance spectroscopy. The WO₃/spiro‐OMeTAD layer exhibits better hole extraction ability and faster hole mobility. The WO₃ layer particularly improves the open‐circuit voltage (V_OC) by lowering the quasi‐Fermi energy level for holes and reducing charge recombination, resulting in high V_OC (1.17 V in the champion cell). In addition, the WO₃ layer as a scaffold layer promotes the formation of a uniform and pinhole‐free spiro‐OMeTAD overlayer in the WO₃/spiro‐OMeTAD layer. High stability under thermal and humid conditions stems from this property. The study presents a facile approach for improving the efficiency and stability of PSCs by stacking an organic layer on an inorganic layer.     

Less is More: Dopant‐Free Hole Transporting Materials for High‐Efficiency Perovskite Solar Cells

Perovskite solar cells have delivered power conversion efficiency beyond 22% in less than seven years, implying the potential for the paradigm shift of low‐cost photovoltaics with high efficiency and low embedded energy. Besides the “perovskite fever,” the development of new hole transport materials (HTM), especially dopant‐free HTMs, is another research hotspot. This is because the currently used HTMs, such as spiro‐OMeTAD derivatives, require additional chemical doping process to ensure sufficient conductivity and proper ionic potential level for efficient hole transport and collection. However, the commonly used dopants are volatile and hygroscopic which not only increase the complexity and cost of device fabrication but also deteriorate the device stability. So far, there have been several reviews on new HTMs, but review or analysis on dopant‐free HTMs is scarce. In this review, all reported dopant‐free HTMs are categorized into four primary different types and lessons will be learned during the separate discussions. The stability test behavior of all the intrinsic HTMs will be evaluated directly. In the end, the correlations between the properties of the intrinsic HTMs and parameters of the devices will be plotted to shed light on the future direction of development of this field.     

Carbon Nanoparticles in High‐Performance Perovskite Solar Cells

In the past few years, organic–inorganic metal halide ABX₃ perovskites (A = Rb, Cs, methylammonium, formamidinium (FA); B = Pb, Sn; X = Cl, Br, I) have rapidly emerged as promising materials for photovoltaic applications. Tuning the film morphology by various deposition techniques and additives is crucial to achieve solar cells with high performance and long‐term stability. In this work, carbon nanoparticles (CNPs) containing functional groups are added to the perovskite precursor solution for fabrication of fluorine‐doped tin oxide/TiO₂/perovskite/spiro‐OMeTAD/gold devices. With the addition of CNPs, the perovskite films are thermally more stable, contain larger grains, and become more hydrophobic. NMR experiments provide strong evidence that the functional groups of the CNPs interact with FA cations already in the precursor solution. The fabricated solar cells show a power‐conversion efficiency of 18% and negligible hysteresis.