The azure dyes: their purification and physicochemical properties. II. Purification of azure B.

A method is described for the purification of the dye azure B in quantities sufficient for biological staining experiments on a larger scale. The method is based on the use of column chromatography. Two columns are employed. In column A with silica gel as adsorbent the azure B fraction is isolated from a suitable substrate ('technical' azure B gained by a modification of Bernthsen's synthesis of methylene blue, or polychrome methylene blue) using an acetate-formate mixture as eluent. In column B, on an Amberlite polymeric adsorbent (XAD-2) the acetate-formate anions are exchanged in chloride. Regeneration of both columns is possible: KMnO4, Na2S2O4 and water are run through column A; 5% NaOH, methanol and water through column B. Purification of azure B on economic terms is thus attained. The opinion is expressed that this method is also applicable to the purification of other cationic dyes.     

Purification of Thionin, Azure A, Azure B and Methylene Blue

Column and paper chromatography of four thiazin dyes revealed both inorganic and organic impurities. In thionin, azure A, azure B and methylene blue, sodium and other metal cations were found as inorganic impurities. The analysis for organic impurities revealed that the dyes were mixtures; specifically each dye contained one or more of the other dyes as impurities. Inorganic impurities were detected by ashing the dyes in the presence of H₂SO₄ and chromatographing the sulfate salts on paper. They were removed by filtration through ion exchange resins. Organic impurities were detected by paper chromatography and removed by column chromatography on Woelm's neutral alumina.     

The Azure Dyes: Their Purification and Physicochemical Properties. I. Purification of Azure A

A method is described for the separation of azure A from commezcial samples of polychrome methylene blue. Up to 300 mg of the pure dye may be isolated in this way. The method is based on chromatography using columns 90 cm high, 7 cm in diameter, loaded with 3 g of polychrome methylene blue. The absorbent is silica gel, the eluent a mixture of acetic and formic acid.

Poor solubility of the dye acetate in water necessitates dissociation of the acetate by alkalinization and subsequent conversion of the dye to the chloride with diluted Ha. Demethylation that occasionally occurs during this procedure is negligible. Pure azure A does not spontaneously demethylate under ordinary conditions.     

Zinc Chloride Methylene Blue, Ii. Preparation of Giesma and Wright Type Low Azure B Blood Stains from Dichromate Oxidized Commercial Dye

TO determine the amount of K₂Cr₂O₇ required to produce optimal Giemsa type staining, six 1 g amounts (corrected for dye content) of zinc methylene blue were oxidized with graded quantities of K₂Cr₂O₇ to produce 4, 8, 12, 16, 20 and 24% conversion of methylene blue to azure B. These were heated with a blank control 15 minutes at 100 C in 60-65 ml 0.4 N HCI. cooled, and adjusted to 50 ml to give 20 mg original dye/ml. Aliquots were then diluted to 1% and stains were made by the “Wet Giemsa” technic (Lillie and Donaldson 1979) using 6 ml 1% polychrome methylene blue, 4 ml 1% cosin (corrected for dye content), 2 ml 0.1 M pH 6.3 phosphate buffer, 5 ml acetone, and 23 ml distilled water. The main is added last and methanol fixed blood films are stained immediately for 20-40 min.

For methylene blue supplied by MCB 12-H-29, optimal stains were obtained with preparations containing 20 and 24% conversion of methylene blue to azure B. With methylene blue supplied by Aldrich (080787), 16% conversion of methylene blue to azure B was optimal. Eosinates prepared from a low azure B/methylene blue preparation selected in this way give good stains when used as a Wright stain in 0.3% methanol solution. However, when the 600 mg eosinate solution in glycerol methanol is supplemented with 160 mg of the same azure B/methylene blue chloride the mixture fails to perform well. The HCI precipitation of the chloride apparently produces the zinc methylene blue chloride salt which is poorly soluble in alcohol. It appears necessary to have a zinc-free azure B/methylene blue chloride to supplement the probably zinc-free eosinate used in the Giemsa mixture.     

Zinc Chloride Methylene Blue. I. Biological Stain History, Physical Characteristics and Approximation of Azure B Content of Commercial Samples

Zinc chloride methylene blue appeared on the market almost contemporaneously with the zinc-free medicinal form. The former has rarely been reported as being used in blood stains. Recent suspension of manufacture of medicinal methylene blue by it. principal American producer has excited interest in the use of the zinc chloride form for the preparation of blood stains. According to Lillie (1944a,b) the azure B content of zinc chloride methylene blue may have varied from 5 to 30% in the samples studied. Taking the Merck Index (1968, 1976) figures for the spectroscopic absorption maximum (λmax) of 667.8 and 668 nm as standard, recent samples of zinc chloride methylene blue are calculated to contain 6-8% azure B. These figures are baaed on 1) the shift of λmax after exhaustive pH 9.5 chloroform extraction, 2) evaluation of the actual ratio of the observed TiCl₂ dye content to the theoretical for pure zinc chloride methylene blue, 3) comparison of spectroscopic and staining effects of graded hot dichromate oxidation products with those of highly purified azure B-methylene blue mixtures of known proportions.

As far as can be found, medicinal methylene blue is almost the exclusive source of cosin polychrome methylene blue blood stains. Lillie (1944c) included a short series comparing 5 zinc chloride methylene blues with a dozen medicinal methylene blue samples; all were oxidized with hot dichromate to produce successful Wright stains. No effort was made to remove the zinc Exhaustive pH 9.5 chloroform extraction of zinc chloride methylene blue (lot MCB 12-H-29) yielded a small amount of red dye which when extracted into 0.1 N HCI gave λmax = 650. The extraction moved the absorption peak of the zinc chloride methylene blue from 667 to 668 nm and the midpoint of the 90% maximum absorption band, 18 nm wide, from 666.5 to 667.5 nm.     

Microspectrophotometric Studies of Romanowsky Stained Blood Cells. III. The Action of Methylene Blue and Azure B

The performances of two standardized Romanowsky stains (azure B/eosin and azure B/methylene blue/eosin) have been compared with each other and with a methylene blue/eosin stain. Visible-light absorbance spectra of various hematological substrates have been measured. These have been analyzed in terms of the quantities of bound azure B, methylene blue and eosin dimers and monomers, and in terms of the CIE color coordinates. It has been found that the addition of methylene blue to azure B/eosin produces little change in performance, at least using these two analytical methods. Methylene blue/eosin does not produce the purplish colorations typical of the Romanowsky effect. This is due not to differences between the spectra of methylene blue and azure B, but to the fact that methylene blue does not facilitate the binding of eosin to cellular substrates to the same extent as azure B.     

Lower Azure B Methylene Blue Ratios in Giemsa Type Blood and Malaria Stains

Starting from ancient reports that rare samples of methylene blue were apparently sufficiently contaminated with azures to give red plasmodial and red purple nuclear chromatin in Chenzinsky type methylene blue eosin stains, it was decided to determine how little azure B would suffice for such staining in methylene blue eosin stains. The traditional 1902 Giemsa had an azure:methylene blue: eosin ratio of about 6:3:6.3:10; Lillie's 1943 formula had a 5:7:10 ratio. In the current series of tests 5:7:10 (I), 4:8:10 (II), 3:9:10 (III), 2:10:10 (IV), 1:11:10 (V), and 0:12:10 (VI) were used. Malaria and blood stains were better than the standard 5:7:10 (I) in III, IV and II in that order. Normal and leukemic human blood, mouse blood with Plasmodium berghei, and monkey blood with the CDC strain of Pl. falciparum were used as test materials. The staining mixtures were made from highly purified samples of azure B and methylene blue. Staining mixtures contained 12 ml 0.1% thiazin dye, 10 ml 0.1% eosin, 2 ml each of glycerol, methanol and 0.1 M phosphate buffer pH 6.5, 3 ml acetone as accelerator, and distilled water to make 40 ml; staining times of 10-30 min were used.     

ON THE NATURE OF THE DYE PENETRATING THE VACUOLE OF VALONIA FROM SOLUTIONS OF METHYLENE BLUE

When uninjured cells of Valonia are placed in methylene blue dissolved in sea water it is found, after 1 to 3 hours, that at pH 5.5 practically no dye penetrates, while at pH 9.5 more enters the vacuole. As the cells become injured more dye enters at pH 5.5, as well as at pH 9.5. No dye in reduced form is found in the sap of uninjured cells exposed from 1 to 3 hours to methylene blue in sea water at both pH values. When uninjured cells are placed in azure B solution, the rate of penetration of dye into the vacuole is found to increase with the rise in the pH value of the external dye solution. The partition coefficient of the dye between chloroform and sea water is higher at pH 9.5 than at pH 5.5 with both methylene blue and azure B. The color of the dye in chloroform absorbed from methylene blue or from azure B in sea water at pH 5.5 is blue, while it is reddish purple when absorbed from methylene blue and azure B at pH 9.5. Dry salt of methylene blue and azure B dissolved in chloroform appears blue. It is shown that chiefly azure B in form of free base is absorbed by chloroform from methylene blue or azure B dissolved in sea water at pH 9.5, but possibly a mixture of methylene blue and azure B in form of salt is absorbed from methylene blue at pH 5.5, and azure B in form of salt is absorbed from azure B in sea water at pH 5.5. Spectrophotometric analysis of the dye shows the following facts. 1. The dye which is absorbed by the cell wall from methylene blue solution is found to be chiefly methylene blue. 2. The dye which has penetrated from methylene blue solution into the vacuole of uninjured cells is found to be azure B or trimethyl thionine, a small amount of which may be present in a solution of methylene blue especially at a high pH value. 3. The dye which has penetrated from methylene blue solution into the vacuole of injured cells is either methylene blue or a mixture of methylene blue and azure B. 4. The dye which is absorbed by chloroform from methylene blue dissolved in sea water is also found to be azure B, when the pH value of the sea water is at 9.5, but it consists of azure B and to a less extent of methylene blue when the pH value is at 5.5. 5. Methylene blue employed for these experiments, when dissolved in sea water, in sap of Valonia, or in artificial sap, gives absorption maxima characteristic of methylene blue. Azure B found in the sap collected from the vacuole cannot be due to the transformation of methylene blue into this dye after methylene blue has penetrated into the vacuole from the external solution because no such transformation detectable by this method is found to take place within 3 hours after dissolving methylene blue in the sap of Valonia. These experiments indicate that the penetration of dye into the vacuole from methylene blue solution represents a diffusion of azure B in the form of free base. This result agrees with the theory that a basic dye penetrates the vacuole of living cells chiefly in the form of free base and only very slightly in the form of salt. But as soon as the cells are injured the methylene blue (in form of salt) enters the vacuole. It is suggested that these experiments do not show that methylene blue does not enter the protoplasm, but they point out the danger of basing any theoretical conclusion as to permeability on oxidation-reduction potential of living cells from experiments made or the penetration of dye from methylene blue solution into the vacuole, without determining the nature of the dye inside and outside the cell.     

Azure Stains

Two uses of methylene azure are suggested. This dye gives a very good nuclear stain after most fixations when preceded by weak NaOH; but eosin Y cannot be used as a counter-stain. Methylene azure also proves very useful in the Mallory eosinemethylene-blue technic, in which it can be substituted to advantage for polychrome methylene blue. The following three schedules are recommended:

2.5% aqueous phloxined˙ 15 minutes

0.1% aqueous azured˙ 1-30 minutes

2.5% aqueous phloxined˙ 15 minutes

Mixture in equal parts of 0.1% azure and 0.1% methylene blued˙ 30 minutes

2.5% aqueous phloxined˙ 1 minute

1.0% aqueous azured˙ 1-2 minutes

Of these the first two give rather better results; but when time is lacking the third is quite satisfactory.     

Qualitative Analysis by Thin-Layer Chromatography of Some Common Dyes Used in Biological Staining

Thin-layer chromatography will resolve impurities in commercial dyes, and will do so much faster than paper chromatography. Solvent systems consisting of (a) n-propanol: n-butanol: NH₄OH (conc.): H₂O—4:4:1:1; (b) n-propanol: NH₄OH (conc.): H₂O—8:1:1 on silica gel G plates; and (c) n-propanol: NH₄OH (conc.): H₂O-7:2:1 on Adsorbosil plates were found to be the most effective. Dyes studied were azure A, azure B, azure C, methylene blue, toluidine blue O, thionin, pyronin B, pyronin Y, methyl green, crystal violet amido black 10B and buffalo black (NBR).     

Microspectrophotometric studies of Romanowsky stained blood cells. III. The action of methylene blue and azure B

The performances of two standardized Romanowsky stains (azure B/eosin and azure B/methylene blue/eosin) have been compared with each other and with a methylene blue/eosin stain. Visible-light absorbance spectra of various hematological substrates have been measured. These have been analyzed in terms of the quantities of bound azure B, methylene blue and eosin dimers and monomers, and in terms of the CIE color coordinates. It has been found that the addition of methylene blue to azure B/eosin produces little change in performance, at least using these two analytical methods. Methylene blue/eosin does not produce the purplish colorations typical of the Romanowsky effect. This is due not to differences between the spectra of methylene blue and azure B, but to the fact that methylene blue does not facilitate the binding of eosin to cellular substrates to the same extent as azure B.     

Additional Schiff-Type Reagents for Use in Cytochemistry

Twenty-four new Schiff-type reagents were discovered in a survey of 140 different dyes. These dyes include acid fuchsin, acridine yellow, acriflavine hydrochloride, azure C., Bismarck brown R, Bismarck brown Y, celestine blue B, chrysoidine 3R, chrysoidine Y extra, cresyl violet, crystal violet, gentian violet, methylene blue, neutral violet, phenosafranin, phosphine GN, proflavine, toluidine blue O, and toluylene blue. Positive results obtained with crystal violet and a few samples of methylene blue are considered due to impurities. Various chemical extractions, aldehyde blocking reagents, and enzymatic treatments were used to verify the aldehyde specificity of the above dye-SO₂, reagents as well as azure A, brilliant cresyl blue, neutral red, safranin O, and thionin which have been mentioned by other workers. These reagents were tested in the Feulgen reaction for DNA and the PAS reaction for polysaccharides. Absorption curves were obtained from individual nuclei stained for DNA. The absorption peaks ranged from 450 mμ, to 630 mμ. depending on the dye studied. The Feulgen reaction could be followed by the PAS reaction or vice versa in mouse intestine using reactive dyes of complementary colors. The evidence indicates that a potential Schiff-type reagent must have at least one free NH₂ group on the dye molecule.     

Thiazin Dyes in Supravital Staining of nerve Fibers

Supravital staining by thiazins of segments of small intestine and mesentery of young dogs was studied with reference to specificity for nervous tissue. Attempts to secure a purer form of methylene blue by alumina adsorption and alcohol elution of the commercial, medicinal dye yielded a product which appeared to be structurally different from the original dye. The treated dye had absorption maxima from 620 to 655 mμ in contrast with 665 for the untreated. Small nerve bundles were stained by the treated dye after 2 to 4 hours of immersion, but staining was always incomplete. Staining by untreated methylene blue was compared with that by the leucobase, thionol, methylene green, toluidine blue, new methylene blue and the azures. It was concluded that the specificity for nerve fibers resides mainly in the =N(CH₃)₂Cl radical, although some specificity appears to be effected by the methyl groups on the trivalent nitrogen, since azure A (dimethyl) and azure C (mono-methyl) stained weakly, but thionin did not. Methylene green showed some specificity but stained weakly. The leucobase was less active than the reoxidized dye obtained from it.     

The purification of methylene blue and azure B by solvent extraction and crystallization.

Detailed schemes are described for the preparation of purified methylene blue and azure B from commercial samples of methylene blue. Purified methylene blue is obtained by extracting a solution of the commercial product in an aqueous buffer (pH 9.5) with carbon tetrachloride. Methylene blue remains in the aqueous layer but contaminating dyes pass into the carbon tetrachloride. Metal salt contaminants are removed when the dye is crystallized by the addition of hydrochloric acid at a final concentration of 0.25 N. Purified azure B is obtained by extracting a solution of commercial methylene blue in dilute aqueous sodium hydroxide (pH 11-11.5) with carbon tetrachloride. In this pH range, methylene blue is unstable and yields azure B. The latter passes into the carbon tetrachloride layer as it is formed. Metal salt contaminants remain in the aqueous layer. A concentrated solution oa azure B is obtained by extracting the carbon tetrachloride layer with 4.5 X 10(-4)N hydrobromic acid. The dye is then crystallized by increasing the hydrobromic acid concentration to 0.23 N. Thin-layer chromatography of the purified dyes shows that contamination with related thiazine dyes is absent or negligible. Ash analyses reveal that metal salt contamination is also negligible (sulphated ash less than 0.2%).     

Azure a-Schiff, Alcian Blue, HIO4-Schiff, Naphthol Yellow S—A Sequential Staining Method for Paraffin Sections

Paraffin sections from tissue fixed 4-12 hr in 10% formalin containing 0.5% cetyl pyridinium chloride, and washed 2 hr, were stained as follows: (1) Hydrolyze in 5 N HCl at room temperature for 8.5-9 min, or use standard Feulgen hydrolysis at 60 C. (2) Stain in azure A-Schiff, 0.5% in bisulfite bleach (1 N HCl, 5; 10% Na₂S₂O₅, 5; and distilled water 90—parts by volume) for 10 min. (3) Place in bisulfite bleach 2 changes, 2 min each; wash in water, 1-2 min. (4) Stain in Alcian blue (0.1% in 0.01 2V HCl, pH 2.0) for 10 min. (5) Place in 0.01 N HCl for 2-3 min; wash in water for 1-2 min. (6) Oxidize in 0.5% HIO₄ for 5 min; wash in water, 1-2 min. (7) Stain in Schiff's leucofuchsiu, 10 min. (8) Treat with bisulfite bleach as in step 3; wash in running water, 10 min. (9) Stain in naphthol yellow S (0.01% in 1% acetic acid) for 1-2 min. (10) Place in 1% acetic acid for 2 min, dehydrate in tertiary butanol, clear and cover. Result: DNA is deep blue; acidic mucins are light blue; neutral polysaccharides, red to magenta; and proteins, yellow. Proper timing of the hydrolysis for the Feulgen reaction is the most critical step. Overhydrolysis results in green nuclei (staining by naphthol yellow S) whereas purplish nuclei are the results of insufficient hydrolysis.     

A polychromatic staining method for epoxy embedded tissue: a new combination of methylene blue and basic fuchsine for light microscopy.

A simple and rapid method is described for staining semithin sections of material embedded in epoxy resin for observing tissues prior to transmission electron microscopy. The method is suitable for tissue fixed with a glutaraldehyde-formaldehyde mixture and postfixed in osmium tetroxide. No etching or oxidizing procedures are necessary. Sections 0.5-0.8 microm thick are dried onto a slide and stained with either 0.75% methylene blue and 0.25% azure B or 0.5% methylene blue and 0.5% azure II in 0.5% aqueous borax and heated over a flame for 8-10 sec. The slides are rinsed with water, then stained the same way with 0.1% basic fuchsine in 5% aqueous ethanol. Cytoplasm stains blue; nuclei darker blue; collagen, mucus and elastin pink to red; fat and intracellular lipid droplets gray-green.     

SPECTROPHOTOMETRIC STUDIES OF PENETRATION : V. RESEMBLANCES BETWEEN THE LIVING CELL AND AN ARTIFICIAL SYSTEM IN ABSORBING METHYLENE BLUE AND TRIMETHYL THIONINE.

The rate of diffusion through the non-aqueous layer of the protoplasm depends largely on the partition coefficients mentioned above. Since these cannot be determined we have employed an artificial system in which chloroform is used in place of the non-aqueous layer of the protoplasm. The partition coefficients may be roughly determined by shaking up the aqueous solutions with chloroform and analyzing with the spectrophotometer (which is necessary with methylene blue because we are dealing with mixtures). This will show what dyes may be expected to pass through the protoplasm into the vacuole in case it behaves like the artificial system. From these results we may conclude that the artificial system and the living cell act almost alike toward methylene blue and azure B, which supports the notion of non-aqueous layers in the protoplasm. There is a close resemblance between Valonia and the artificial system in their behavior toward these dyes at pH 9.5. In the case of Nitella, on the other hand, with methylene blue solution at pH 9.2 the sap in the artificial system takes up relatively more azure B (absorption maximum at 650 mµ) than the vacuole of the living cell (655 mµ). But both take up azure B much more rapidly than methylene blue. A comparison cannot be made between the behavior of the artificial system and that of the living cell at pH 5.5 since in the latter case there arises a question of injury to cells before enough dye is collected in the sap for analysis.     

A polychromatic staining method for epoxy embedded tissue: a new combination of methylene blue and basic fuchsine for light microscopy

A simple and rapid method is described for staining semithin sections of material embedded in epoxy resin for observing tissues prior to transmission electron microscopy. The method is suitable for tissue fixed with a glutaraldehyde-formaldehyde mixture and postfixed in osmium tetroxide. No etching or oxidizing procedures are necessary. Sections 0.5-0.8 µm thick are dried onto a slide and stained with either 0.75% methylene blue and 0.25% azure B or 0.5% methylene blue and 0.5% azure II in 0.5% aqueous borax and heated over a flame for 8-10 sec. The slides are rinsed with water, then stained the same way with 0.1% basic fuchsine in 5% aqueous ethanol. Cytoplasm stains blue; nuclei darker blue; collagen, mucus and elastin pink to red; fat and intracellular lipid droplets gray-green.     

A polychromatic staining method for epoxy embedded tissue: a new combination of methylene blue and basic fuchsine for light microscopy

A simple and rapid method is described for staining semithin sections of material embedded in epoxy resin for observing tissues prior to transmission electron microscopy. The method is suitable for tissue fixed with a glutaraldehyde-formaldehyde mixture and postfixed in osmium tetroxide. No etching or oxidizing procedures are necessary. Sections 0.5–0.8 µm thick are dried onto a slide and stained with either 0.75% methylene blue and 0.25% azure B or 0.5% methylene blue and 0.5% azure II in 0.5% aqueous borax and heated over a flame for 8–10 sec. The slides are rinsed with water, then stained the same way with 0.1% basic fuchsine in 5% aqueous ethanol. Cytoplasm stains blue; nuclei darker blue; collagen, mucus and elastin pink to red; fat and intracellular lipid droplets gray-green.     

The Oxidation Products of Methylene Blue

The mechanism of the oxidation of methylene blue varies with the conditions. The formation of trimethyl thionin (azure B) and of asymmetrical dimethyl thionolin (azure A) is followed under alkaline conditions by that of dimethyl thionin (methylene violet) and under acid conditions by that of monomethyl thionin (named by authors azure C).

Simple and practical methods are given for the preparation of azure A and azure C. The latter product, which has not been obtained from methylene blue hitherto, has valuable staining properties as a nuclear and bacterial stain in tissue and may also be employed satisfactorily as a substitute for azure A in the MacNeal tetrachrome formula as a blood stain or substitute for the Giemsa stain.

Azure B has no particular merit in staining.

Azure C proves to be a very valuable stain. A procedure is given for its use with eosin Y and orange II as counterstains, by which it is possible to demonstrate bacteria in tissue and at the same time the cytological elements of the tissue.