Biotechnological production of xylitol in a three-phase fluidized bed bioreactor with immobilized yeast cells in Ca-alginate beads

Cells of Candida guilliermondii entrapped in Ca-alginate beads were used for xylitol production, from concentrated hemicellulose hydrolyzate of sugarcane bagasse, in a fluidized bed bioreactor (FBR). The maximum xylitol concentration 28.9 g xylitol/L was obtained at a high aeration rate of 600 mL/min after 70 h of fermentation, indicating that the use of high aeration rate in this system is favored for better oxygen transfer into the immobilized cells. The specific xylitol productivity and the xylitol yield were of 0.4 g xylitol/L.h and 0.58 g xylitol/g xylose respectively. The immobilization efficiency at the end of the fermentation was of 65 %. After 90 h of fermentation xylitol productivity and yield decreased to 0.25 g xylitol/L.h and 0.47 g xylitol/g xylose respectively, indicating the beginning of xylitol consumption by the yeast. The use of FBR system with immobilized cells presented high xylitol yield and productivity.     

Metabolic behavior of immobilized Candida guilliermondii cells during batch xylitol production from sugarcane bagasse acid hydrolyzate

Candida guilliermondii cells, immobilized in Ca-alginate beads, were used for batch xylitol production from concentrated sugarcane bagasse hydrolyzate. Maximum xylitol concentration (20.6 g/L), volumetric productivity (0.43 g/L. h), and yield (0.47 g/g) obtained after 48 h of fermentation were higher than similar immobilized-cell systems but lower than free-cell cultivation systems. Substrates, products, and biomass concentrations were used in material balances to study the ways in which the different carbon sources were utilized by the yeast cells under microaerobic conditions. The fraction of xylose consumed to produce xylitol reached a maximum value (0.70) after glucose and oxygen depletion while alternative metabolic routes were favored by sub-optimal conditions.     

Use of immobilized Candida cells on xylitol production from sugarcane bagasse

In this study we used the yeast Candida guilliermondii FTI 20037 immobilized by entrapment in Ca-alginate beads (2.5-3 mm diameter) for xylitol production from concentrated sugarcane bagasse hemicellulosic hydrolysate in a repeated batch system. The fermentation runs were carried out in 125- and 250-ml Erlenmeyer flasks placed in an orbital shaker at 30 degrees C and 200 rpm during 72 h, keeping constant the proportion between work volume and flask total volume. According to the results, cell viability was substantially high (98%) in all fermentative cycles. The values of parameters xylitol yield and volumetric productivity increased significantly with the reutilization of the immobilized biocatalysts. The highest values of xylitol final concentration (11.05 g/l), yield factor (0.47 g/g) and volumetric productivity (0.22 g/lh) were obtained in 250-ml Erlenmeyer flasks containing 80 ml of medium plus 20 ml of immobilized biocatalysts. The support used in this study (Ca-alginate) presented stability in the experimental conditions used. The results show that the use of immobilized cells is a promising approach for increasing the xylitol production rates.     

Xylitol production from sugarcane bagasse hydrolyzate in fluidized bed reactor. Effect of air flowrate

Cells of Candida guilliermondii immobilized onto porous glass spheres were cultured batchwise in a fluidized bed bioreactor for xylitol production from sugarcane bagasse hemicellulose hydrolyzate. An aeration rate of only 25 mL/min ensured minimum yields of xylose consumption (0.60) and biomass production (0.14 g(DM)/g(Xyl)), as well as maximum xylitol yield (0.54 g(Xyt)/g(Xyl)) and ratio of immobilized to total cells (0.83). These results suggest that cell metabolism, although slow because of oxygen limitation, was mainly addressed to xylitol production. A progressive increase in the aeration rate up to 140 mL/min accelerated both xylose consumption (from 0.36 to 0.78 g(Xyl)/L.h) and xylitol formation (from 0.19 to 0.28 g(Xyt)/L.h) but caused the fraction of immobilized to total cells and the xylitol yield to decrease up to 0.22 and 0.36 g(Xyt)/g(Xyl), respectively. The highest xylitol concentration (17.0 g(Xyt)/L) was obtained at 70 mL/min, but the specific xylitol productivity and the xylitol yield were 43% and 22% lower than the corresponding values obtained at the lowest air flowrate, respectively. The concentrations of consumed substrates and formed products were used in material balances to evaluate the xylose fractions consumed by C. guilliermondii for xylitol production, complete oxidation through the hexose monophosphate shunt, and cell growth. The experimental data collected at variable oxygen level allowed estimating a P/O ratio of 1.35 mol(ATP)/mol(O) and overall ATP requirements for biomass growth and maintenance of 3.4 mol(ATP)/C-mol(DM).     

Variables that affect xylitol production from sugarcane bagasse hydrolysate in a zeolite fluidized bed reactor

The operational conditions for xylitol production by fermentation of sugarcane bagasse hydrolysate in a fluidized bed reactor with cells immobilized on zeolite were evaluated. Fermentations were carried out under different conditions of air flowrate (0.0125-0.0375 vvm), zeolite mass (100-200 g), initial pH (4-6), and xylose concentration (40-60 g/L), according to a 2(4) full factorial design. The air flowrate increase resulted in a metabolic deviation from product to biomass formation. On the other hand, the pH increase favored both the xylitol yield (Y(P/S)) and volumetric productivity (Q(P)), and the xylose concentration increase positively influenced the xylitol concentration. The best operational conditions evaluated were based on the use of an air flowrate of 0.0125 vvm, 100 g of zeolite, pH 6, and xylose concentration of 60 g/L. Under these conditions, 38.5 g/L of xylitol were obtained, with a Y(P/S) of 0.72 g/g, Q(P) of 0.32 g/L.h, and cell retention of 25.9%.     

Improvement in xylitol production from sugarcane bagasse hydrolysate achieved by the use of a repeated-batch immobilized cell system

Candida guilliermondii cells were immobilized in Ca-alginate beads and used for xylitol production from concentrated sugarcane bagasse hydrolysate during five successive fermentation batches, each lasting 48 hours. The bioconversion efficiency of 53.2%, the productivity of 0.50 g/l x h and the final xylitol concentration of 23.8 g/l obtained in the first batch increased to 61.5%, 0.59 g/l x h and 28.4 g/l, respectively, in the other four batches (mean values), with variation coefficients of up to 2.3%.     

Xylitol production from corn fiber and sugarcane bagasse hydrolysates by Candida tropicalis

A natural isolate, Candida tropicalis was tested for xylitol production from corn fiber and sugarcane bagasse hydrolysates. Fermentation of corn fiber and sugarcane bagasse hydrolysate showed xylose uptake and xylitol production, though these were very low, even after hydrolysate neutralization and treatments with activated charcoal and ion exchange resins. Initial xylitol production was found to be 0.43 g/g and 0.45 g/g of xylose utilised with corn fiber and sugarcane bagasse hydrolysate respectively. One of the critical factors for low xylitol production was the presence of inhibitors in these hydrolysates. To simulate influence of hemicellulosic sugar composition on xylitol yield, three different combinations of mixed sugar control experiments, without the presence of any inhibitors, have been performed and the strain produced 0.63 g/g, 0.68 g/g and 0.72 g/g of xylose respectively. To improve yeast growth and xylitol production with these hydrolysates, which contain inhibitors, the cells were adapted by sub culturing in the hydrolysate containing medium for 25 cycles. After adaptation the organism produced more xylitol 0.58 g/g and 0.65 g/g of xylose with corn fiber hydrolysate and sugarcane bagasse hydrolysate respectively.     

Xylitol production by immobilized recombinant Saccharomyces cerevisiae in a continuous packed-bed bioreactor

Continuous xylitol production with two different immobilized recombinant Saccharomyces cerevisiae strains (H475 and S641), expressing low and high xylose reductase (XR) activities, was investigated in a lab-scale packed-bed bioreactor. The effect of hydraulic residence time (HRT; 1.3-11.3 h), substrate/cosubstrate ratio (0.5 and 1), recycling ratio (0, 5, and 10), and aeration (anaerobic and oxygen limited conditions) were studied. The cells were immobilized by gel entrapment using Ca-alginate as support and the beads were treated with Al(3+) to improve their mechanical strength. Xylose was converted to xylitol using glucose as cosubstrate for regeneration of NAD(P)H required in xylitol formation and for generation of maintenance energy. The stability of the recombinant strains after 15 days of continuous operation was evaluated by XR activity and plasmid retention analyses. Under anaerobic conditions the volumetric xylitol productivity increased with decreasing HRT with both strains. With a recycling ratio of 10, volumetric productivities as high as 3.44 and 5.80 g/L . h were obtained with the low XR strain at HRT 1.3 h and with the high XR strain at HRT 2.6 h, respectively. However, the highest overall xylitol yields on xylose and on cosubstrate were reached at higher HRTs. Lowering the xylose/cosubstrate ratio from 1 to 0.5 increased the overall yield of xylitol on xylose, but the productivity and the xylitol yield on cosubstrate decreased. Under oxygen limited conditions the effect of the recycling ratio on production parameters was masked by other factors, such as an accumulation of free cells in the bioreactor and severe genetic instability of the high XR strain. Under anaerobic conditions the instability was less severe, causing a decrease in XR activity from 0.15 to 0.10 and from 3.18 to 1.49 U/mg with the low and high XR strains, respectively. At the end of the fermentation, the fraction of plasmid bearing cells in the beads was close to 100% for the low XR strain; however, it was significantly lower for the high XR strain, particularly for cells from the interior of the beads. (c) 1996 John Wiley & Sons, Inc.     

酵母发酵蔗渣半纤维素水解物生产木糖酶

采用二次正交旋转组合设计研究了蔗渣半纤维素水解过程中硫酸浓度与液 固比对木糖收率的影响。回归分析表明 ,这两个因素与木糖的收率之间存在显著的回归关系。通过回归方程优化水解条件 ,当硫酸浓度 2 .4g L ,液 固 =6 .2 ,在蒸汽压力 2 .5× 10 4Pa的条件下水解 2 .5h ,10 0g蔗渣可水解生成木糖约 2 4g。大孔树脂吸附层析处理蔗渣半纤维素水解物 ,能有效地减少其中的酵母生长抑制物含量 ,显著改善水解物的发酵性能。用大孔树脂在pH 2条件下处理过的蔗渣半纤维素水解物作基质 ,含木糖 2 0 0g L ,产木糖醇酵母菌株CandidatropicalisAS2 .1776发酵 110h耗完基质中的木糖 ,生成木糖醇 12 7g L ,产物转化率 0 .6 4(木糖醇g 木糖g) ,产物生成速率 1.15g L·h .     

Coupling two sizes of CSTR-type bioreactors for sequential lactic acid and xylitol production from hemicellulosic hydrolysates of vineshoot trimmings

This study develops a system for the efficient valorisation of hemicellulosic hydrolysates of vineshoot trimmings. By connecting two reactors of 2L and 10L, operational conditions were set up for the sequential production of lactic acid and xylitol in continuous fermentation, considering the dependence of the main metabolites and fermentation parameters on the dilution rate. In the first bioreactor, Lactobacillus rhamnosus consumed all the glucose to produce lactic acid at 31.5°C, with 150rpm and 1L of working volume as the optimal conditions. The residual sugars were employed for the xylose to xylitol bioconversion by Debaryomyces hansenii in the second bioreactor at 30°C, 250rpm and an air-flow rate of 2Lmin(-1). Several steady states were reached at flow rates (F) in the range of 0.54-5.33mLmin(-1), leading to dilution rates (D) ranging from 0.032 to 0.320h(-1) in Bioreactor 1 and from 0.006 to 0.064h(-1) in Bioreactor 2. The maximum volumetric lactic acid productivity (Q(P LA)=2.908gL(-1)h(-1)) was achieved under D=0.266h(-1) (F=4.44mLmin(-1)); meanwhile, the maximum production of xylitol (5.1gL(-1)), volumetric xylitol productivity (Q(P xylitol)=0.218gL(-1)h(-1)), volumetric rate of xylose consumption (Q(S xylose)=0.398gL(-1)h(-1)) and product yield (0.55gg(-1)) were achieved at an intermediate dilution rate of 0.043h(-1) (F=3.55mLmin(-1)). Under these conditions, ethanol, which was the main by-product of the fermentation, was produced in higher amounts (1.9gL(-1)). Finally, lactic acid and xylitol were effectively recovered by conventional procedures.     

Influence of cultivation conditions on xylose-to-xylitol bioconversion by a new isolate of Debaryomyces hansenii

About 270 yeast isolates were screened for xylitol production using xylose as the sole carbon source. The best isolate, Debaryomyces hansenii UFV-170, released 5.84 g L(-1) xylitol from 10 g L(-1) xylose after 24 h, corresponding to a yield of xylitol on consumed substrate (Y(P/S)) of 0.54 g g(-1). This strain was cultivated batch-wise at variable starting concentrations of xylose (S(o)) and biomass (X(o)) and agitation intensity, in order to improve xylitol production and to evaluate, through simple carbon balances, the influence of these conditions on xylose metabolism. Under the best microaerobic conditions (S(o) = 53 g L(-1), X(o) = 1.4 g L(-1), 200 rpm), xylitol production reached 37.0 g L(-1), corresponding to xylitol volumetric productivity of 1.0 g L(-1)h(-1), specific productivity of 0.22 g g(-1)h(-1) and Y(P/S) = 0.76 g g(-1). Almost 83% of xylose was consumed for xylitol production, the rest being consumed for growth, while respiration was negligible. The new isolate appeared to be a promising alternative for industrial xylitol bioproduction.     

化学改性甘蔗渣对固定化细胞发酵产丁醇的影响

旨在研究化学改性的甘蔗渣作为固定化载体对丙酮丁醇梭菌Clostridium acetobutylicum XY16发酵制备生物丁醇的影响。首先利用不同浓度的聚乙烯亚胺(PEI)和1 g/L戊二醛(GA)对甘蔗渣表面进行化学改性,增强甘蔗渣对Clostridium acetobutylicum XY16的附载能力。经4 g/L聚乙烯亚胺和1 g/L戊二醛改性的甘蔗渣(添加量10 g/L)应用到固定化批次发酵中,发酵36 h后丁醇和总溶剂浓度最高,分别达到了12.24 g/L和21.67 g/L,同时溶剂的生产速率达到0.60 g/(L·h),生产速率比游离细胞和未改性甘蔗渣固定化细胞分批发酵分别提高了130.8%和66.7%。在此基础上对改性甘蔗渣固定化的细胞进行6次重复批次发酵,丁醇和总溶剂的产量稳定,溶剂生产速率逐渐提高至0.83 g/(L·h),同时转化率也提高至0.42 g/g。     

Xylitol production from D-xylose byCandida guillermondii: Fermentation behaviour

Summary The ability ofCandida guillermondii to produce xylitol from xylose and to ferment individual non xylose hemicellulosic derived sugars was investigated in microaerobic conditions. Xylose was converted into xylitol with a yield of 0,63 g/g and ethanol was produced in negligible amounts. The strain did not convert glucose, mannose and galactose into their corresponding polyols but only into ethanol and cell mass. By contrast, fermentation of arabinose lead to the formation of arabitol. On D-xylose medium,Candida guillermondii exhibited high yield and rate of xylitol production when the initial sugar concentration exceeded 110 g/l. A final xylitol concentration of 221 g/l was obtained from 300 g/l D-xylose with a yield of 82,6% of theoretical and an average specific rate of 0,19 g/g.h.Nomenclature Q_p average volumetric productivity of xylitol (g xylitol/l per hour) - q_p average specific productivity of xylitol (g xylitol/g of cells per hour) - So initial xylose concentration (g/l) - tf incubation time (hours) - Y_P/S xylitol yield (g of xylitol produced/g of xylose utilized) - Y_E/S ethanol yield (g of ethanol produced/g of substrate utilized) - Y_X/S cells yield (g of cells/g of substrate utilized) - specific growth rate coefficient (h^–1) - _max maximum specific growth rate coefficient (h^–1)     

Effects of sulfuric acid loading and residence time on the composition of sugarcane bagasse hydrolysate and its use as a source of xylose for xylitol bioproduction

A 2(2) full factorial design was employed to evaluate the effects of sulfuric acid loading and residence time on the composition of sugarcane bagasse hydrolysate obtained in a 250-L reactor. The acid loading and the residence time were varied from 70 to 130 mg acid per gram of dry bagasse and from 10 to 30 min, respectively, while the temperature (121 degrees C) and the bagasse loading (10%) were kept constant. Both the sulfuric acid loading and the residence time influenced the concentrations of xylose and inhibitors in the hydrolysate. The highest xylose concentration (22.71 g/L) was achieved when using an acid loading of 130 mg/g and a residence time of 30 min. These conditions also led to increased concentrations of inhibiting byproducts in the hydrolysate. All of the hydrolysates were vacuum-concentrated to increase the xylose concentration, detoxified by pH alteration and adsorption into activated charcoal, and used for xylitol bioproduction in a stirred tank reactor. Neither the least (70 mg/g, 10 min) nor the most severe (130 mg/g, 30 min) hydrolysis conditions led to the best xylitol production (37.5 g/L), productivity (0.85 g/L h), and yield (0.78 g/g).     

Influence of temperature and pH on xylitol production from xylose by Debaryomyces hansenii

The production of xylitol from concentrated synthetic xylose solutions (S(o) = 130-135 g/L) by Debaryomyces hansenii was investigated at different pH and temperature values. At optimum starting pH (pH(o) = 5.5), T = 24 degrees C, and relatively low starting biomass levels (0.5-0.6 g(x)/L), 88% of xylose was utilized for xylitol production, the rest being preferentially fermented to ethanol (10%). Under these conditions, nearly 70% of initial carbon was recovered as xylitol, corresponding to final xylitol concentration of 91.9 g(P)/L, product yield on substrate of 0.81 g(P)/g(S), and maximum volumetric and specific productivities of 1.86 g(P)/L x h and 1.43 g(P)/g(x) x h, respectively. At higher and lower pH(o) values, respiration also became important, consuming up to 32% of xylose, while negligible amounts were utilized for cell growth (0.8-1.8%). The same approach extended to the effect of temperature on the metabolism of this yeast at pH(o) = 5.5 and higher biomass levels (1.4-3.0 g(x)/L) revealed that, at temperatures ranging from 32-37 degrees C, xylose was nearly completely consumed to produce xylitol, reaching a maximum volumetric productivity of 4.67 g(P)/L x h at 35 degrees C. Similarly, both respiration and ethanol fermentation became significant either at higher or at lower temperatures. Finally, to elucidate the kinetic mechanisms of both xylitol production and thermal inactivation of the system, the related thermodynamic parameters were estimated from the experimental data with the Arrhenius model: activation enthalpy and entropy were 57.7 kJ/mol and -0.152 kJ/mol x K for xylitol production and 187.3 kJ/mol and 0.054 kJ/mol x K for thermal inactivation, respectively.     

The influence of aeration and hemicellulosic sugars on xylitol production by Candida tropicalis

The influence of other hemicellulosic sugars (arabinose, galactose, mannose and glucose), oxygen limitation, and initial xylose concentration on the fermentation of xylose to xylitol was investigated using experimental design methodology. Oxygen limitation and initial xylose concentration had considerable influences on xylitol production by Canadida tropicalis ATCC 96745. Under semiaerobic conditions, the maximum xylitol yield was 0.62 g/g substrate, while under aerobic conditions, the maximum volumetric productivity was 0.90 g/l h. In the presence of glucose, xylose utilization was strongly repressed and sequential sugar utilization was observed. Ethanol produced from the glucose caused 50% reduction in xylitol yield when its concentration exceeded 30 g/l. When complex synthetic hemicellulosic sugars were fermented, glucose was initially consumed followed by a simultaneous uptake of the other sugars. The maximum xylitol yield (0.84 g/g) and volumetric productivity (0.49 g/l h) were obtained for substrates containing high arabinose and low glucose and mannose contents.     

Immobilized cells cultivated in semi-continuous mode in a fluidized bed reactor for xylitol production from sugarcane bagasse

Summary Xylitol production from sugarcane bagasse hemicellulosic hydrolyzate was evaluated in a fluidized bed reactor operated in semi-continuous mode, using cells immobilized on porous glass. The fermentative process was performed during five successive cycles of 72 h each one. The lowest xylitol production occurred in the first cycle, where a high cell concentration (12 g l⁻¹) was observed. In the subsequent cycles the xylitol concentration was ever increasing due to the cells adaptation to the medium. In the last one, 18 g xylitol l⁻¹ was obtained with a yield factor of 0.44 g g⁻¹ and volumetric productivity of 0.32 g l⁻¹ h⁻¹.     

Itaconic acid production by immobilizedAspergillus terreus from xylose and glucose

Summary Aspergillus terreus NRRC 1960 spores were entrapped in calcium alginate gel beads or alternotely the fungal mycelium was immobilized either on Celite R-626 or in agar gel cubes, and the biocatalyst was employed both in repeated batch and in continuous column reactors to produce itaconic acid from D-xylose or D-glucose. The highest itaconic acid yield obtained in a submerged culture batch fermentation was 54.5% based on total initial glucose (55 g/l) with a volumetric productivity of 0.32 g/l h, and 44.8% from xylose (67 g/l) with a productivity of 0.20 g/l h. In a repeated batch fermentation mycelium immobilized in agar gel had a productivity of 0.112 g/l h, and mycelium grown from spores immobilized in calcium alginate gel 0.06 g/l h, both from xylose (60 g/l). With the best immobilized biocatalyst system used employing Celite R-626 as a carrier, volumetric productivities of 1.2 g/l h from glucose and 0.56 g/l h from xylose (both at 60 g/l) were obtained in continuous column operation for more than 2 weeks.     

Isolation and Characterization of Xylitol-Producing Yeasts from the Gut of Colleopteran Insects

A total of 35 yeasts were isolated from the gut of beetles collected from Hyderabad city, India. Twenty of these yeasts utilized xylose as a sole carbon source but only 12 of these converted xylose to xylitol. The ability to convert xylose to xylitol varied among the isolates and ranged from 0.12 to 0.58 g/g xylose. Based on the phenotypic characteristics and phylogenetic analysis of the D1/D2 domain sequence of 26S rRNA gene, these isolates were identified as members of Pichia, Candida, Issatchenkia, and Clavispora. Strain YS 54 (CBS 10446), which was phylogenetically similar to Pichia caribbica and which formed hat-shaped ascospore characteristics of the genus Pichia, was the best xylitol producer (0.58 g xylitol/g xylose). YS 54 was also capable of producing xylitol from sugarcane bagasse hydrolysate and the efficiency of conversion was 0.32 g xylitol/g xylose after 20 cycles of adaptation in medium containing sugarcane bagasse hydrolysate.     

Enhanced Xylitol Production by Precultivation of Candida guilliermondii Cells in Sugarcane Bagasse Hemicellulosic Hydrolysate

The present work evaluated the key enzymes involved in xylitol production (xylose reductase [XR] and xylitol dehydrogenase [XDH]) and their correlation with xylose, arabinose, and acetic acid assimilation during cultivation of Candida guilliermondii FTI 20037 cells in sugarcane bagasse hemicellulosic hydrolysate. For this purpose, inocula previously grown either in sugarcane bagasse hemicellulosic hydrolysate (SBHH) or in semidefined medium (xylose as a substrate) were used. The highest xylose/acetic acid consumption ratio (1.78) and the lowest arabinose consumption (13%) were attained in the fermentation using inoculum previously grown in semidefined medium (without acetic acid and arabinose). In this case, the highest values of XR (1.37 U mg prot⁻¹) and XDH (0.91 U mg prot⁻¹) activities were observed. The highest xylitol yield (∼0.55 g g⁻¹) and byproducts (ethanol and glycerol) formation were not influenced by inoculum procedure. However, the cell previously grown in the hydrolysate was effective in enhancing xylitol production by keeping the XR enzyme activity at high levels (around 0.99 U·mg_prot⁻¹), reducing the XDH activity (34.0%) and increasing xylitol volumetric productivity (26.5%) with respect to the inoculum cultivated in semidefined medium. Therefore, inoculum adaptation to SBHH was shown to be an important strategy to improve xylitol productivity.