Study of the acclimation stage and of the effect of the biodegradability on the performance of a microbial fuel cell

In this work, it has been studied the production of electricity and the oxidation of the pollutants contained in a synthetic wastewater fed with glucose and peptone of soybean as carbon sources, using a mediator-less microbial fuel cell (MFC). Special attention has been paid to the acclimation stage, in which it was found that with high hydraulic and solid retention times it is possible to obtain a very efficient process with a 90% COD removal and practically total conversion of COD into electricity (considering the typical stoichiometric yield of heterotrophic biomass). The influence of concentration sludge was studied working with three different amounts of suspended solids, from 120 to 14000 mg. The maximum power density increased exponentially with the concentration sludge from 2.1 mW m⁻² to 11 mW m⁻² at the highest concentration sludge. More over, the percentage of the influent COD used to produce electricity was higher than 100% when the highest sludge concentration was used. This was explained taking into account the endogenous metabolism of micro-organisms presented in the system.     

Effect of external resistance on bacterial diversity and metabolism in cellulose-fed microbial fuel cells

External resistance affects the performance of microbial fuel cells (MFCs) by controlling the flow of electrons from the anode to the cathode. The purpose of this study was to determine the effect of external resistance on bacterial diversity and metabolism in MFCs. Four external resistances (20, 249, 480, and 1000 Ω) were tested by operating parallel MFCs independently at constant circuit loads for 10 weeks. A maximum power density of 66 mW m⁻² was achieved by the 20 Ω MFCs, while the MFCs with 249, 480, and 1000 Ω external resistances produced 57.5, 27, and 47 mW m⁻², respectively. Denaturing gradient gel electrophoresis analysis of partial 16S rRNA genes showed clear differences between the planktonic and anode-attached populations at various external resistances. Concentrations of short chain fatty acids were higher in MFCs with larger circuit loads, suggesting that fermentative metabolism dominated over anaerobic respiration using the anode as the final electron acceptor.     

Pre-acclimation of a wastewater inoculum to cellulose in an aqueous-cathode MEC improves power generation in air-cathode MFCs

Cellulose has been used in two-chamber microbial fuel cells (MFCs), but power densities were low. Higher power densities can be achieved in air-cathode MFCs using an inoculum from a two-chamber, aqueous-cathode microbial electrolysis cell (MEC). Air-cathode MFCs with this inoculum produced maximum power densities of 1070 mW m⁻² (cathode surface area) in single-chamber and 880 mW m⁻² in two-chamber MFCs. Coulombic efficiencies ranged from 25% to 50%, and COD removals were 50-70% based on total cellulose removals of 60-80%. Decreasing the reactor volume from 26 to 14 mL (while maintaining constant electrode spacing) decreased power output by 66% (from 526 to 180 mW m⁻²) due to a reduction in total mass of cellulose added. These results demonstrate that air-cathode MFCs can produce high power densities with cellulose following proper acclimation of the inoculum, and that organic loading rates are important for maximizing power densities from particulate substrates.     

Horizontal or vertical photobioreactors? How to improve microalgae photosynthetic efficiency

The productivity of a vertical outdoor photobioreactor was quantitatively assessed and compared to a horizontal reactor. Daily light cycles in southern Spain were simulated and applied to grow the microalgae Chlorella sorokiniana in a flat panel photobioreactor.The maximal irradiance around noon differs from 400 μmol photons m⁻² s⁻¹ in the vertical position to 1800 μmol photons m⁻² s⁻¹ in the horizontal position. The highest volumetric productivity was achieved in the simulated horizontal position, 4 g kg culture⁻¹ d⁻¹. The highest photosynthetic efficiency was found for the vertical simulation, 1.3 g of biomass produced per mol of PAR photons supplied, which compares favorably to the horizontal position (0.85 g mol⁻¹) and to the theoretical maximal yield (1.8 g mol⁻¹). These results prove that productivity per unit of ground area could be greatly enhanced by placing the photobioreactors vertically.     

Luminostat operation: a tool to maximize microalgae photosynthetic efficiency in photobioreactors during the daily light cycle?

The luminostat regime has been proposed as a way to maximize light absorption and thus to increase the microalgae photosynthetic efficiency within photobioreactors. In this study, simulated outdoor light conditions were applied to a lab-scale photobioreactor in order to evaluate the luminostat control under varying light conditions. The photon flux density leaving the reactor (PFD_out) was varied from 4 to 20 μmol photons m⁻² s⁻¹and the productivity and photosynthetic efficiency of Chlorella sorokiniana were assessed.Maximal volumetric productivity (1.22 g kg⁻¹ d⁻¹) and biomass yield on PAR photons (400-700 nm) absorbed (1.27 g mol⁻¹) were found when PFD_out was maintained between 4 and 6 μmol photons m⁻² s⁻¹. The resultant photosynthetic efficiency was comparable to that already reported in a chemostat-controlled reactor. A strict luminostat regime could not be maintained under varying light conditions. Further modifications to the luminostat control are required before application under outdoor conditions.     

Enhancement in current density and energy conversion efficiency of 3-dimensional MFC anodes using pre-enriched consortium and continuous supply of electron donors

Using a pre-enriched microbial consortium as the inoculum and continuous supply of carbon source, improvement in performance of a three-dimensional, flow-through MFC anode utilizing ferricyanide cathode was investigated. The power density increased from 170 W/m³ (1800 mW/m²) to 580 W/m³ (6130 mW/m²), when the carbon loading increased from 2.5 g/l-day to 50 g/l-day. The coulombic efficiency (CE) decreased from 90% to 23% with increasing carbon loading. The CEs are among the highest reported for glucose and lactate as the substrate with the maximum current density reaching 15.1 A/m². This suggests establishment of a very high performance exoelectrogenic microbial consortium at the anode. A maximum energy conversion efficiency of 54% was observed at a loading of 2.5 g/l-day. Biological characterization of the consortium showed presence of Burkholderiales and Rhodocyclales as the dominant members. Imaging of the biofilms revealed thinner biofilms compared to the inoculum MFC, but a 1.9-fold higher power density.     

Power overshoot in two-chambered microbial fuel cell (MFC)

A two-chamber microbial fuel cell was started using iron-reducing strains as inoculum and acetate as carbon sources. The tested microbial fuel cell had an open-circuit voltage of 0.67 V, and reached 1045 mA m⁻² and a power density of 486 mW m⁻² at 0.46 V before power overshoot occurred. Anodic reactions were identified as the rate-determining steps. Stirring the anolyte insignificantly increased cell performance, suggesting a minimal external mass transfer resistance from the anolyte to the anodic biofilm. Data regression analysis indicates that charge transfer resistance at the biofilm-anode junction was negligible. The order of magnitude estimation of electrical conductance indicates that electron transfer resistance had an insignificant effect on microbial fuel cell performance. Resistance in electrogens for substrate utilization is proposed to induce microbial fuel cell power overshoot.     

Electricity generation and modeling of microbial fuel cell from continuous beer brewery wastewater

Electricity production and modeling of microbial fuel cell (MFC) from continuous beer brewery wastewater was studied in this paper. A single air-cathode MFC was constructed, carbon fiber was used as anode and diluted brewery wastewater (COD = 626.58 mg/L) as substrate. The MFC displayed an open-circuit voltage of 0.578 V and a maximum power density of 9.52 W/m³ (264 mW/m²). Using the model based on polarization curve, various voltage losses were quantified. At current density of 1.79 A/m², reaction kinetic loss and mass transport loss both achieved to 0.248 V; while ohmic loss was 0.046 V. Results demonstrated that it was feasible and stable for producing bioelectricity from brewery wastewater; while the most important factors which influenced the performance of the MFC are reaction kinetic loss and mass transport loss.     

Improved performance of membrane free single-chamber air-cathode microbial fuel cells with nitric acid and ethylenediamine surface modified activated carbon fiber felt anodes

Surface modifications of anode materials are important for enhancing power generation of microbial fuel cell (MFC). Membrane free single-chamber air-cathode MFCs, MFC-A and MFC-N, were constructed using activated carbon fiber felt (ACF) anodes treated by nitric acid and ethylenediamine (EDA), respectively. Experimental results showed that the start-up time to achieve the maximum voltages for the MFC-A and MFC-N was shortened by 45% and 51%, respectively as compared to that for MFC-AT equipped with an unmodified anode. Moreover, the power output of MFCs with modified anodes was significantly improved. In comparison with MFC-AT which had a maximum power density of 1304 mW/m², the MFC-N achieved a maximum power density of 1641 mW/m². The nitric acid-treated anode in MFC-A increased the power density by 58% reaching 2066 mW/m². XPS analysis of the treated and untreated anode materials indicated that the power enhancement was attributable to the changes of surface functional groups.     

Density dependent effects of an infaunal suspension-feeding bivalve (Austrovenus stutchburyi) on sandflat nutrient fluxes and microphytobenthic productivity

We examined in situ the density dependent effects of an infaunal suspension-feeding bivalve, Austrovenus stutchburyi (hereafter Austrovenus) on sandflat nutrient fluxes and microphytobenthic (MPB) production. Nine experimental plots (0.64 m^− 2) were established at two locations separated by 300 m. Ambient fauna was left intact and Austrovenus added to plots creating a density range from 20 to 2000 ind. m^− 2. Three weeks later, light and dark benthic chambers (area = 0.114 m^− 2) were deployed to measure MPB production and nutrient fluxes. Austrovenus density was positively correlated with organic content and porosity but did not affect other sediment properties (grain size, pigment content) or resident macrofauna. In dark chambers there was a net influx of oxygen (O₂) into the sediments which increased with Austrovenus density (from − 0.45 to − 1.21 mmol m^− 2 h^− 1) whereas in light chambers there was a net efflux from the sediments which decreased with density (from 0.90 to 0.31 mmol m^− 2 h^− 1). Significant (p < 0.01) multiple linear regression models explained respectively 42% and 72% of the variability in the dark and light chamber O₂ fluxes with Austrovenus density as the most important predictor variable. When the effects of significant co-variables (light intensity, grain size) were accounted for, the negative relationship between O₂ flux and Austrovenus density was less steep in light chambers (ANCOVA p < 0.001) suggesting a stimulation of MPB production at higher densities. Estimates of gross MPB primary production indicated a 30% increase in rates of carbon fixation with Austrovenus density (from 36 to 48 mg C m^− 2 h^− 1). Ammonium (NH₄⁺) was released from the sediments in both light and dark chambers and increased with Austrovenus density by a factor of 5.9-6.9×. Multiple linear regression models were significant for light and dark chambers (p < 0.001; r² 86-87%) with Austrovenus again as the most important variable influencing fluxes. ANCOVA results (p < 0.001) indicated that in dark chambers NH₄⁺ efflux increased with Austrovenus density at a rate 1.76× greater than in light chambers. These results indicate that the greater efflux of NH₄⁺ at high densities was being trapped by photosynthesising MPB at the sediment-water interface supporting higher rates of primary production. Our results suggest that a reduction in Austrovenus density will lower nutrient fluxes potentially influencing system productivity by reducing MPB production.     

Electrocatalytic activity of anodic biofilm responses to pH changes in microbial fuel cells

This study investigates the effects of anodic pH on electricity generation in microbial fuel cells (MFCs) and the intrinsic reasons behind them. In a two-chamber MFC, the maximum power density is 1170 ± 58 mW m⁻² at pH 9.0, which is 29% and 89% higher than those working at pH 7.0 and 5.0, respectively. Electrochemical measurements reveal that pH affects the electron transfer kinetics of anodic biofilms. The apparent electron transfer rate constant (k_app) and exchange current density (i₀) are greater whereas the charge transfer resistance (R_ct) is smaller at pH 9.0 than at other conditions. Scanning electron microscopy verifies that alkaline conditions benefit biofilm formation in MFCs. These results demonstrate that electrochemical interactions between bacteria and electrodes in MFCs are greatly enhanced under alkaline conditions, which can be one of the important reasons for the improved MFC output.     

Electricity production in membrane-less microbial fuel cell fed with livestock organic solid waste

Two different MFC configurations designed for handling solid wastes as a feedstock were evaluated in batch mode: a single compartment combined membrane-electrodes (SCME) design; and a twin-compartment brush-type anode electrodes (TBE) design (reversed T-shape MFC with two-air cathode) without a proton exchange membrane (PEM). Cattle manure was tested as a model livestock organic solid waste feedstock. Under steady conditions, voltage of 0.38 V was recorded with an external resistance of 470 Ω. When digested anaerobic sludge was used as the seed in the SCME design, a maximum power density of 36.6 mW/m² was recorded. When hydrogen-generating bacteria (HGB) were used as the seed used in the TBE design, a higher power density of 67 mW/m² was recorded.     

Development of chemically defined media supporting high cell density growth of Ketogulonicigenium vulgare and Bacillus megaterium

The immediate precursor of L-ascorbic acid, or vitamin C, is 2-keto-l-gulonic acid (2-KLG). This is commonly produced commercially by Ketogulonicigenium vulgare and Bacillus megaterium, using corn steep liquor powder (CSLP) as an organic nitrogen source. In this study, the effects of the individual CSLP components (amino acids, vitamins, and metal elements) on 2-KLG production were evaluated, with the aim of developing a complete, chemically defined medium for 2-KLG production. Forty components of CSLP were analyzed, and key components were correlated to biomass, 2-KLG productivity, and consumption rate of L-sorbose. Glycine had the greatest effect, followed by serine, biotin, proline, nicotinic acid, and threonine. The combination of 0.28 g L⁻¹ serine, 0.36 g L⁻¹glycine, 0.18 g L⁻¹ threonine, 0.28 g L⁻¹proline, 0.19 g L⁻¹nicotinic acid, and 0.62 mg L⁻¹biotin in a chemically defined medium produced the highest maximum biomass concentration (4.2 × 10⁹ cfu mL⁻¹), 2-KLG concentration (58 g L⁻¹), and yield (0.76 g g⁻¹) after culturing for 28 h.     

Microorganism-immobilized carbon nanoparticle anode for microbial fuel cells based on direct electron transfer

A fast and convenient bacterial immobilization method was proposed as an attempt to improve the anode efficiency of a microbial fuel cell, in which bacteria were entrapped into carbon nanoparticle matrix. The direct electron transfer from the entrapped bacterial cells to the anode was verified using cyclic voltammogram (CV). Using the immobilized bioanode, the start-up time of the MFC was greatly reduced. Meanwhile, the maximum power density of 1,947 mW m⁻² with the modified anode was much higher than that with the biofilm-based carbon cloth anode (1,479 mW m⁻²). Impedance measurements suggested that performance improvement resulted from the decrease in charge transfer and diffusion resistances. The results demonstrated that bacteria immobilization using carbon nanoparticle matrix was a simple and efficient approach for improving the anodes performances in MFCs.     

Performance of microbial fuel cell in response to change in sludge loading rate at different anodic feed pH

Performance of two dual chambered mediator-less microbial fuel cells (MFCs) was evaluated at different sludge loading rate (SLR) and feed pH. Optimum performance in terms of organic matter removal and power production was obtained at the SLR of 0.75 kg COD kg VSS⁻¹ d⁻¹. Maximum power density of 158 mW/m² and 600 mW/m² was obtained in MFC-1 (feed pH 6.0) and MFC-2 (feed pH 8.0), respectively. Internal resistance of the cell decreased with increase in SLR. When operated only with biofilm on anode, the maximum power density was 109.5 mW/m² in MFC-1 and 459 mW/m² in MFC-2, which was, respectively, 30% and 23.5% less than the value obtained in MFC-1 and MFC-2 at SLR of 0.75 kg COD kg VSS⁻¹ d⁻¹. Maximum volumetric power of 15.51 W/m³ and 36.72 W/m³ was obtained in MFC-1 and MFC-2, respectively, when permanganate was added as catholyte. Higher feed pH (8.0) favoured higher power production.     

Energy efficiency of an outdoor microalgal photobioreactor sited at mid-temperate latitude

This work examined the energetic performance of a 6-month semi-continuous cultivation of Scenedesmus obliquus in an outdoor photobioreactor at mid-temperate latitude, without temperature control. By measuring the seasonal biomass production (mean 11.31, range 1.39-23.67 g m⁻² d⁻¹), higher heating value (22.94 kJ g⁻¹) and solar irradiance, the mean seasonally-averaged photosynthetic efficiency (2.18%) and gross energy productivity (0.27 MJ m⁻² d⁻¹) was calculated. When comparing the solar energy conversion efficiency to the energy investment for culture circulation, significant improvements in reactor energy input must be made to make the system viable. Using the data collected to model the energetic performance of a substitute photobioreactor design, we conclude that sustainable photobioreactor cultivation of microalgae in similar temperate climates requires a short light path and low power input, only reasonably obtained by flat-panel systems. However, temperature control was not necessary for effective long-term cultivation.     

Variation in vegetation and seed banks of freshwater lakes with contrasting intensity of aquaculture along the Yangtze River, China

We examined species composition and richness in the seed banks and established vegetation in lakes along the Yangtze River with two contrasting aquaculture types: pen-culture lakes, characterized by pen-culture of commercial fish and crab, and lake-culture lake with more intensive stocking of the entire lake. The mean live biomass and species richness of submerged vegetation was significantly reduced or absent in lake-culture lakes (0-159 g m⁻² and 0-0.3 species per sample, respectively), compared to those with pen-culture lakes (1552-2971 g m⁻² and 1.5-3.2 species per sample, respectively) in all three study years. Also mean seedling density and species richness of seed banks were significantly lower in these lake-culture lakes (133 m⁻² vs. 265 m⁻² and 0.6 species vs. 0.9 species per sample, respectively). These results suggest that intensive aquaculture in these lakes has had serious negative effects on submerged vegetation and the associated seed banks. Vegetation history was partly reflected by distribution patterns of seed banks across sediment depth strata. A principal component analysis produced a very clear separation of lakes from pen-culture and lake-culture on the basis of their species composition. Moreover, the principal component analysis also indicated that the variation in the soil seed bank corresponded poorly with vegetation data. This probably reflects species-specific strategies for seed production.     

Reduction of ammonia and volatile organic compounds from food waste-composting facilities using a novel anti-clogging biofilter system

The performance of a pilot-scale anti-clogging biofilter system (ABS) was evaluated over a period of 125 days for treating ammonia and volatile organic compounds emitted from a full-scale food waste-composting facility. The pilot-scale ABS was designed to intermittently and automatically remove excess biomass using an agitator. When the pressure drop in the polyurethane filter bed was increased to a set point (50 mm H₂O m⁻¹), due to excess biomass acclimation, the agitator automatically worked by the differential pressure switch, without biofilter shutdown. A high removal efficiency (97-99%) was stably maintained for the 125 days after an acclimation period of 1 week, even thought the inlet gas concentrations fluctuated from 0.16 to 0.55 g m⁻³. Due the intermittent automatic agitation of the filter bed, the biomass concentration and pressure drop in the biofilter were maintained within the ranges of 1.1-2.0 g-DCW g PU⁻¹ and below 50 mm H₂O m⁻¹, respectively.     

Can small water level fluctuations affect the biomass of Nymphaea alba in large lakes?

In this study we investigated above-ground biomass and morphological responses of a floating-leaved plant species, Nymphaea alba, to small spring water level manipulations (0.1–0.5 m) in a large, shallow lake over a 9-year period (1995–2003). A year effect was found in mean annual above-ground plant biomass with higher values found in years of low water levels, 275–339 g DW m⁻² in 1995 and 2003 against 143–198 g DW m⁻² in 1996–2002 (no data transformation). No significant changes in biomass patterns were observed within each season (one summer peak), except in 1995 when a summer decline in biomass occurred. The amplitude and duration of exposure to high water levels affected the spring and annual above ground biomass of N. alba. The plant responded to high spring water levels by producing longer and thinner petioles to preserve leaves from flooding while no significant changes in leaf surface area (except in May) and leaf/petiole biomass ratio were obtained. The results are interpreted with regard to plant adaptations to changing environments (biomass allocation patterns in the different plant organs and stem density) and the effects of other abiotic factors relevant to the size of the system. We concluded that small deviations in spring water level can be driving forces in a large system in controlling the above-ground biomass of this floating-leaved plant.     

Overyielding and the role of complementary use of nitrogen in wetland plant communities

Biodiversity and ecosystem functioning experiments have demonstrated that plant biomass of species grown in mixtures is often greater than plant biomass of monocultures (i.e., mixtures over yield). While we understand that plant species utilize resources differently, how a combination of species increases resource use and productivity is not well known, especially in wetland ecosystems. Here, we used a mesocosm experiment to explore diversity effects on plant biomass production and to examine the role of N partitioning as a mechanism for overyielding in wetland ecosystems. Plant functional groups (FGs) represented the unit of diversity, and we included five levels of diversity (0-4 FGs). To test for N partitioning, we used a stable isotope technique to determine niche breadth and proportion similarity of inorganic N use (NO₃⁻ and NH₄⁺) for individual FGs as well as mixtures containing 3 and 4 FGs. We found that total plant biomass increased in the first season from an average of 290 ± 60 SE g ash-free dry mass (AFDM) m⁻² at the 1 FG level to 490 ± 70 g AFDM m⁻² at the 4 FG level and in the second season from an average of 560 ± 80 g AFDM m⁻² at the 1 FG level to 1000 ± 90 g AFDM m⁻² at the 4 FG level indicating overyielding. Plant species comprising the majority of mesocosm biomass demonstrated preferential uptake of ¹⁵NO₃⁻, while species with relatively less biomass (e.g., Acorus calamus and Carex crinita) preferred ¹⁵NH₄⁺. Concentrations of ¹⁵N in biomass increased with FG richness, but only in the ¹⁵NO₃⁻ treatment. Niche breadth did not vary among levels of FG richness. We observed a greater niche overlap with an increase of FGs, with species taking up greater proportion of ¹⁵NO₃⁻ than ¹⁵NH₄⁺. Our results indicate that plant overyielding in wetland mesocosms is not the result of niche partitioning of N chemical forms, but is associated with greater uptake of NO₃.